There is a new version of dmc available for skylake.
Following additions from ver1.27

1. Fix for the issue where DC_STATE was getting enabled even when
disabled by driver causing data corruption.

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NAnusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1510276712-29590-2-git-send-email-anusha.srivatsa@intel.com

We apply this logic to Gen9 as well. We didn't notice this issue as
most part we've encountered so far only use the crystal as source for
their timestamp registers.

Fixes: dab91783 ("drm/i915: expose command stream timestamp frequency to userspace")
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NLionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171113233455.12085-5-lionel.g.landwerlin@intel.com

Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

Without masking out the old value, we can end up pointing the DDI to a
disabled PLL, which makes the system fall over. Mask out the previous
value before setting the PLL to DDI mapping.

This can be observed by running igt/testdisplay with both an eDP and
HDMI/DP output active.

v2: Add the Bugzilla link

Fixes: 555e38d2 ("drm/i915/cnl: DDI - PLL mapping")
Testcase: igt/testdisplay
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103997
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: NJames Ausmus <james.ausmus@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Tested-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171201021700.13504-1-james.ausmus@intel.com

It has been many years since the last confirmed sighting (and fix) of an
RC6 related bug (usually a system hang). Remove the parameter to stop
users from setting dangerous values, as they often set it during triage
and end up disabling the entire runtime pm instead (the option is not a
fine scalpel!).

Furthermore, it allows users to set known dangerous values which were
intended for testing and not for production use. For testing, we can
always patch in the required setting without having to expose ourselves
to random abuse.

v2: Fixup NEEDS_WaRsDisableCoarsePowerGating fumble, and document the
lack of ilk support better.
v3: Clear intel_info->rc6p if we don't support rc6 itself.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171201113030.18360-1-chris@chris-wilson.co.uk

As we declare the GPU wedged if the reset fails, such a failure is quite
terminal. Before taking that drastic action, let's sleep first and try
active, in the hope that the hardware has quietened down and is then
able to reset. After a few such attempts, it is fair to say that the HW
is truly wedged.

v2: Always print the failure message now, we precheck whether resets are
disabled.

References: https://bugs.freedesktop.org/show_bug.cgi?id=104007Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171201122011.16841-1-chris@chris-wilson.co.ukReviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>

Reject interlaced modes on VLV/CHV DP outputs. This simply does
not work correctly in the hardware. We do get some output, but
it's quite corrupted.

The available documentation fails to mention this fact. I
contacted some hardware people who eventually managed to locate
the relevant HSD for VLV, which was resolved by declaring
interlaced DP output as not supported. The HSD was never cloned
for CHV even though it inherited most of the hardware and
thus has the same problems with interlaced DP output.

Cc: Dennis Vshivkov <awesome.walrus+bugzilla@gmail.com>
Reported-by: NDennis Vshivkov <awesome.walrus+bugzilla@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103922Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171129180847.30613-1-ville.syrjala@linux.intel.comAcked-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

Get rid of the crtc->config usages from within
intel_pipe_{enable,disable}() by passing in the appropriate
crtc state.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171129153732.3612-3-ville.syrjala@linux.intel.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>

We should make sure the pipe has fully started when we enable it from
the i830 "power well". Otherwise theoretically i830 could also hit
problems with vblank timestamps jumping around (since we skip the
wait during modeset on i830). Additionally moving planes between the
pipes etc. might not work correctly until both pipes are actually up and
running.

v2: Less pointless duplication in the code (Chris)

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171129153732.3612-2-ville.syrjala@linux.intel.com

Previously I was under the impression that the scanline counter
reads 0 when the pipe is off. Turns out that's not correct, and
instead the scanline counter simply stops when the pipe stops, and
it retains it's last value until the pipe starts up again, at which
point the scanline counter jumps to vblank start.

These jumps can cause the timestamp to jump backwards by one frame.
Since we use the timestamps to guesstimage also the frame counter
value on gen2, that would cause the frame counter to also jump
backwards, which leads to a massice difference from the previous value.
The end result is that flips/vblank events don't appear to complete as
they're stuck waiting for the frame counter to catch up to that massive
difference.

Fix the problem properly by actually making sure the scanline counter
has started to move before we assume that it's safe to enable vblank
processing.

v2: Less pointless duplication in the code (Chris)

Cc: stable@vger.kernel.org
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Fixes: b7792d8b ("drm/i915: Wait for pipe to start before sampling vblank timestamps on gen2")
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171129153732.3612-1-ville.syrjala@linux.intel.com

i830_disable_pipe() gets called from the power well code, and thus
we're already holding the power domain mutex. That means we can't
call plane->get_hw_state() as it will also try to grab the
same mutex and will thus deadlock.

Replace the assert_plane() calls (which calls ->get_hw_state()) with
just raw register reads in i830_disable_pipe(). As a bonus we can
now get a warning if plane C is enabled even though we don't even
expose it as a drm plane.

v2: Do a separate WARN_ON() for each plane (Chris)

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Fixes: 51f5a096 ("drm/i915: Add .get_hw_state() method for planes")
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171129125411.29055-1-ville.syrjala@linux.intel.com

Transcoder EDP does not support audio. Let's not try to
read the state of the audio enable bit HSW_AUD_PIN_ELD_CP_VLD
based on the pipe when using transcoder EDP.

While at it make the function static and flatten it.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171129164303.18793-3-ville.syrjala@linux.intel.comReviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

No point in adding the "force audio" property to DP connectors
that don't support audio (g4x or port A).
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171129164303.18793-2-ville.syrjala@linux.intel.comReviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Apparently g4x doesn't support audio over DP. Bspec lists the
bit as "Reserved for Audio Output Enable", and empirical evidence
tells us that the bit won't stick. So stop trying to enable DP
audio on g4x.

Link: https://patchwork.freedesktop.org/patch/msgid/20171129164303.18793-1-ville.syrjala@linux.intel.comReviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103989Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>

To execute a requests requires us to have first woken the device, using
the rpm wakeref (as the request needs to write to hardware to setup the
context/ppGTT and execute on the GPU). So call intel_runtime_pm_get()
around queuing the request; the request itself will then carry a wakeref
until completion.

References: https://bugs.freedesktop.org/show_bug.cgi?id=103994Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171130094231.10405-1-chris@chris-wilson.co.ukReviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>

When capturing the bo, we allocate an error object with an array of
min(vma->size, vma->node.size) pages, plus a bit for compression overhead.
However, when creating the fake vma to describe the bo, only one of the
sizes was filled in, resulting in a too small array. Through my and CI
testing, this was sufficient for the mostly empty NULL context as
it compressed well (or the out-of-bounds access simply didn't cause an
issue). However, in real workloads on Cannonlake, we were overflowing
that array and causing havoc with the random memory corruption.
Reported-by: NRafael Antognolli <rafael.antognolli@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103964
Fixes: 4e90a6e2 ("drm/i915: Record default HW state in the GPU error state")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Tested-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171201001536.13941-1-chris@chris-wilson.co.ukReviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>

drivers/gpu/drm/i915/i915_irq.c|3096 col 29| error: comparison between signed and unsigned integer expressions [-Werror=sign-compare]
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171130125253.21405-1-chris@chris-wilson.co.ukReviewed-by: NMichal Wajdeczko <michal.wajdeczko@intel.com>

This comment predates atomic, and I think with the way we currently
track IPS, it's safe to enable this for the case we switch too.

Changes since v1:
- Keep IPS enabled when switching planes.
Changes since v2:
- Enable IPS when at least one plane is enabled. (Ville)
Changes since v3:
- Actually do what was advertised in v3, sigh! (Ville, CI)
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171122183906.47767-1-maarten.lankhorst@linux.intel.comReviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>

ips_enabled was used as a variable of whether IPS can be enabled or not,
but should be used to test whether IPS is actually enabled.

Changes since v1:
- Call needs_modeset on new crtc state. (Ville)
- IPS can be enabled with sprite plane enabled too. (Ville)
- Fix CDCLK vs IPS workaround. (Ville)
Changes since v2:
- Only re-enable fastset when inheriting mode. (Ville)
- Put the conditions for enabling and disabling IPS in a helper.
Changes since v3:
- Keep the max_cdclk workaround working. (Ville)
- Also check logical cdclk out of paranoia.
- Remove planes check from IPS disable function for initial disable.
- Remove assert_plane_enabled/disabled checks and use
  crtc_state->active_planes for hsw_enable_ips only, always allow
  calling hsw_disable_ips to disable it initially in hw.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171122183901.47720-1-maarten.lankhorst@linux.intel.com
[mlankhorst: pipe_config -> crtc_state (Ville)]
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>

We store a SW state of the t11_t12 timing in 100usec units but have to
program it in 100msec as required by HW. The rounding used during
programming means there will be a mismatch between the SW and HW states
of this value triggering a "PPS state mismatch" error. Avoid this by
storing the already rounded-up value in the SW state.

Note that we still calculate panel_power_cycle_delay with the finer
100usec granularity to avoid any needless waits using that version of
the delay.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103903
Cc: joks <joks@linux.pl>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171129175137.2889-1-imre.deak@intel.com

If the HW is already wedged, attempting to submit a request will
generate an -EIO. If we tried this during suspend, we would abort
whereas all we want to do is to go sleep and throw away the corrupt
state.

Fixes: 5ab57c70 ("drm/i915: Flush logical context image out to memory upon suspend")
Testcase: igt/gem_eio/suspend
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171130102951.14965-1-chris@chris-wilson.co.uk

Testing the texture read performance shows that the same tuning for
the SQ credits is needed on GLK as on BXT/APL. This has been also
confirmed by Altug from the HW team.

V4: Rebase + fix
Signed-off-by: NValtteri Rantala <valtteri.rantala@intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com> (v1)
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1511880305-12166-1-git-send-email-valtteri.rantala@intel.com

This patch makes v9.39 firmware as default firmware for KBL.

Note: GuC logging control is changed with this firmware. GuC is
expecting i915 to set control bit to enable "default logging"
while using GuC action UK_LOG_ENABLE_LOGGING.
However i915 is currently not doing this because it is version
specific change and can be handled entirely in GuC. It will need
to be fixed in future firmwares.

This update includes (since v9.14):

- DCC spec changes for BXT + DCT enabling
- Bug Fix for power conservation feature SLPC_DCC
- Scheduler 1-element submission during DCC cycles.
- SB based Pre-ETM/ETM flow enabling for debug signed GuC/HuC
- Moving GuC non_critical r/w data to lower SRAM 64KB
- Media engine Reset fix.  Correctly marking context for resubmission in
  Media Reset case.
- ABT Disable bug fix. Disabled Evaluation mode on context change.
- Async FW in Engine Schedule feature (not enabled from KMD)
- GuC clean up to align developer build in line to production build.
- Disable ARAT interrupt before programming ARAT delta.
- Memory range check in Parse to avoid failure due to overflow.
- GuC Msg Channel Hang WA - Stall GUC for mmio access when IDI is low
  during CPD flow.
- Fix for submit queue over flow issue
- Enabling IBC on KBL GT3 15W, GT4 45W
- Disabling wrong device ID WA in production signed kernel
- Enabling WA for MSGCH hang issue upto required KBL stepping
- Clear forcewake in CSB when SQ is empty.
- 3Tries of GuC2CSME wake request
- During reset one parameter was not getting accounted
- Disable DCC 1-elem mode submission
- Move UkGuckmdInterface.h file from 2016 folders to common 2016 folder.
- This is file location change.No functional change done as part of this
  check in.
- Enabling Guc Log changes for ultra low logging for OCA
- Enabling Dynamic Render Power Well Hysteresis Programming for Compute
  Worklaods
- Enabling build failure check to catch critical section overflow.
- Disable build.bat redundant prints.
- Move few least used functions to non-critical section.
- Rearrange GuC documentation folder structure.
- Synchronize SLPC internal debug interface with other branches.
- Fixing Issue with Default Guc Log changes for OCA using special Control
  Bit
- Aggressive DCC implementation for supported platforms.

v2: Rebase. Updated commit message.
Signed-off-by: NJeff McGee <jeff.mcgee@intel.com>
Signed-off-by: NSagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Spotswood John A <john.a.spotswood@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Anusha Srivatsa<anusha.srivatsa@intel.com >
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1511972351-574-4-git-send-email-sagar.a.kamble@intel.com

This patch makes v9.29 firmware as default firmware for BXT.

Note: GuC logging control is changed with this firmware. GuC is
expecting i915 to set control bit to enable "default logging"
while using GuC action UK_LOG_ENABLE_LOGGING.
However i915 is currently not doing this because it is version
specific change and can be handled entirely in GuC. It will need
to be fixed in future firmwares.

This update includes (since v8.7):

- Added support to log media reset count for host to read it
- BXT WA for fixing MTP hangs. WaDisableDOPRenderClkGatingAtSubmit
- Sub-feature level control for power management features.
- Minor clean-up for power management interface.
- Unified power management interface and scheduler interface into
  1 file using same version.
- Bug Fix for multi context scheduler flag.
- DCC spec changes for BXT + DCT enabling
- Springboard based Pre-ETM/ETM flow enabling for debug signed GuC/HuC
- Moving GuC non_critical r/w data to lower SRAM 64KB
- Enabled IBC for BXT
- Media engine Reset fix.  Correctly marking context for resubmission in
  Media Reset case.
- SLPC Dynamic RPe fix to resolve issues where incorrect frequency was set.
- ABT Disable bug fix. Disabled Evaluation mode on context change.
- GuC clean up to align developer build in line to production build.
- Disable ARAT interrupt before programming ARAT delta.
- Memory range check in Parse to avoid failure due to overflow.
- Clear forcewake in CSB when SQ is empty.
- SLPC IBC 1.6 for APL to ensure multiplier does not cap IA below Pe.
- Move UkGuckmdInterface.h file from 2016 folders to common 2016 folder.
- This is file location change. No functional change done as part of this
  check in.
- 3 tries of wake request needed from GuC2CSME for ME to wake up. Request
  has come from ME spec
- During reset one parameter was not getting accounted
- Enabling Guc Log changes for ultra low logging for OCA
- Disable build.bat redundant prints.
- Move few least used functions to non-critical section.
- Rearrange GuC documentation folder structure.
- Fixing Issue with Default Guc Log changes for OCA using special Control
  Bit

v2: Rebase. Updated commit message.
Signed-off-by: NJeff McGee <jeff.mcgee@intel.com>
Signed-off-by: NSagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Spotswood John A <john.a.spotswood@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: NAnusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1511972351-574-3-git-send-email-sagar.a.kamble@intel.com

This patch makes v9.33 firmware as default firmware for SKL.

Note: GuC logging control is changed with this firmware. GuC is
expecting i915 to set control bit to enable "default logging"
while using GuC action UK_LOG_ENABLE_LOGGING.
However i915 is currently not doing this because it is version
specific change and can be handled entirely in GuC. It will need
to be fixed in future firmwares.

This update includes (since v6.1):

- HuC RSA Keys updated.
- Adding per engine preemption support in GuC scheduler
- Minor bug fixes.
- Added support to log media reset count for host to read it
- Sub-feature level control for power management features.
- Minor clean-up for power management interface.
- Unified power management interface and scheduler interface into
  1 file using same version.
- Bug Fix for multi context scheduler flag.
- DCC spec changes for BXT + DCT enabling
- SB based Pre-ETM/ETM flow enabling for debug signed GuC/HuC
- Moving GuC non_critical r/w data to lower SRAM 64KB
- Media engine Reset fix.  Correctly marking context for resubmission in
  Media Reset case.
- ABT Disable bug fix. Disabled Evaluation mode on context change.
- Async FW in Engine Schedule feature (not enabled from KMD)
- GuC clean up to align developer build in line to production build.
- DCC consistency fix for SKL
- Disable ARAT interrupt before programming ARAT delta.
- Memory range check in Parse to avoid failure due to overflow.
- Enabled WA for MSGCH hang issue
- Clear forcewake in CSB when SQ is empty.
- Move UkGuckmdInterface.h file from 2016 folders to common 2016 folder.
- This is file location change.No functional change done as part of this
  check in.
- Enable decoupled freq for SKL GT4
- 3 tries of wake request needed from GuC2CSME for ME to wake up. Request
  has come from ME spec
- During reset one parameter was not getting accounted
- Enabling Guc Log changes for ultra low logging for OCA
- Enabling build failure check to catch critical section overflow.
- Disable build.bat redundant prints.
- Move few least used functions to non-critical section.
- Rearrange GuC documentation folder structure.
- Synchronize SLPC internal debug interface with other branches.
- Fixing Issue with Default Guc Log changes for OCA using special Control
  Bit

v2: Rebase. Updated commit message.
Signed-off-by: NJeff McGee <jeff.mcgee@intel.com>
Signed-off-by: NSagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Spotswood John A <john.a.spotswood@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: NAnusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1511972351-574-2-git-send-email-sagar.a.kamble@intel.com

Sagar noticed the check can be consolidated between the engine stats
implementation and the PMU.

My first choice was a static inline helper but that got into include
ordering mess quickly fast so I went with a macro instead. At some point
we should perhaps looking into taking out the non-ringubffer bits from
intel_ringbuffer.h into a new intel_engine.h or something.

v2: Use engine->flags. (Chris Wilson)
v3: Rebase and mark GuC as not yet supported. (Chris Wilson)
v4: Move flag setting to intel_engines_reset_default_submission.
    (Chris Wilson)
v5: Move flag setting to logical_ring_setup.
v6: intel_engines_reset_default_submission is the wrong place to set the
    flag - it needs to be in execlists_set_default_submission. (Sagar)
v7: Flag setting in logical_ring_setup is not required. (Chris)
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Suggested-by: NSagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com> (v6)
Link: https://patchwork.freedesktop.org/patch/msgid/20171129102805.22690-1-tvrtko.ursulin@linux.intel.com

Will be adding a new per-engine flags shortly so it makes sense
to consolidate.

v2: Keep the original code flow in intel_engine_cleanup_cmd_parser.
    (Joonas Lahtinen)
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Suggested-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NSagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171129082409.18189-1-tvrtko.ursulin@linux.intel.com

We seem to be missing some W/A for 2M pages and are getting
a hit on raw GPU read bandwidths (even 30%) even though the
GPU write bandwidths improve (even 10%).

For now, disable THP, which is our only practical source of
2M pages until we have a W/A for the issue.

v2:
- Be explicit that we talk about GPU bandwidths (Eero)
- s/deny/never/ because that's why (Chris)
Reported-by: NValtteri Rantala <valtteri.rantala@intel.com>
Fixes: b901bb89 ("drm/i915/gemfs: enable THP")
Signed-off-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Valtteri Rantala <valtteri.rantala@intel.com>
Cc: Eero Tamminen <eero.t.tamminen@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NMatthew Auld <matthew.auld@intel.com>
Tested-by: NValtteri Rantala <valtteri.rantala@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171127091233.7001-1-joonas.lahtinen@linux.intel.com

In commit 0426c046 ("drm/i915/pmu: Only allow running on a single
CPU") I attempted to clarify the CPU hotplug logic in our PMU
implementation, but missed that a more logical error to return, when
attempting to initialize an event on a currently inactive CPU, is -EINVAL
rather than -ENODEV.

This is because i915 PMU explicitly disallows running counters on more
than one CPU at a time, and is not reporting that the requested CPU does
not exist, or is off-line.
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Reported-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171128105515.21998-1-tvrtko.ursulin@linux.intel.com

Previously we would enable hotplug polling on the outputs immediately
upon construction. This would allow a very early hotplug event to
trigger before we had finishing setting up the driver to handle it.
Instead, move the output polling to the last step of registration, after
we have set up all handlers, including the fbdev configuration.

v2: Symmetrically turnoff the hotplug helper in unregister after the
fbdev is first synchronised then finalized. This stops a late hotplug
event being processed after the interrupts are disabled.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> #v1
Link: https://patchwork.freedesktop.org/patch/msgid/20171128110147.28654-1-chris@chris-wilson.co.uk

The kerneldoc markup for i915_gem_timelines_mark_idle() was incorrect,
so take the opportunity to also convert it from the "mark_idle" to "park"
naming scheme.

drivers/gpu/drm/i915/i915_gem_timeline.c:120: warning: No description found for parameter 'i915'
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171127123054.20966-1-chris@chris-wilson.co.ukReviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>

Switch over from the non-descript dev_priv locals to i915.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171123115338.10270-2-chris@chris-wilson.co.ukReviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>

Since the shrinker is registered and unregistered during
i915_driver_register and i915_driver_unregister, respectively, rename
the init/cleanup functions to match.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171123115338.10270-1-chris@chris-wilson.co.ukReviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>

It may be of interest to both compare the active HW context against the
default (aka NULL) context, to see what has been changed and if either are
corrupt.

v2: Rename the fake vma as fake.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171126220901.14735-1-chris@chris-wilson.co.ukReviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>

Even though all rendering should have been flushed at the end of the
previous requests, add an extra flush after switching to the
kernel_context. As the switch to the kernel_context is used when idling
the gpu (e.g. suspend), having an extra layer of paranoia to ensure
everything is flushed to memory seems sensible.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171126214856.23702-1-chris@chris-wilson.co.ukReviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>

Building i915 without backlight support results in a harmless warning
for intel_panel_set_backlight:

drivers/gpu/drm/i915/intel_panel.c:653:13: error: 'intel_panel_set_backlight' defined but not used [-Werror=unused-function]

This moves it into the CONFIG_BACKLIGHT_CLASS_DEVICE section that
its caller is in.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20171127151239.1813673-2-arnd@arndb.de

The alternative intel_backlight_device_register() definition apparently
never got used, but I have now run into a case of i915 being compiled
without CONFIG_BACKLIGHT_CLASS_DEVICE, resulting in a number of
identical warnings:

drivers/gpu/drm/i915/intel_drv.h:1739:12: error: 'intel_backlight_device_register' defined but not used [-Werror=unused-function]

This marks the function as 'inline', which was surely the original
intention here.

Fixes: 1ebaa0b9 ("drm/i915: Move backlight registration to connector registration")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20171127151239.1813673-1-arnd@arndb.de

As both the hotplug event and fbdev configuration run asynchronously, it
is possible for them to run concurrently. If configuration fails, we were
freeing the fbdev causing a use-after-free in the hotplug event.

<7>[ 3069.935211] [drm:intel_fb_initial_config [i915]] Not using firmware configuration
<7>[ 3069.935225] [drm:drm_setup_crtcs] looking for cmdline mode on connector 77
<7>[ 3069.935229] [drm:drm_setup_crtcs] looking for preferred mode on connector 77 0
<7>[ 3069.935233] [drm:drm_setup_crtcs] found mode 3200x1800
<7>[ 3069.935236] [drm:drm_setup_crtcs] picking CRTCs for 8192x8192 config
<7>[ 3069.935253] [drm:drm_setup_crtcs] desired mode 3200x1800 set on crtc 43 (0,0)
<7>[ 3069.935323] [drm:intelfb_create [i915]] no BIOS fb, allocating a new one
<4>[ 3069.967737] general protection fault: 0000 [#1] PREEMPT SMP
<0>[ 3069.977453] ---------------------------------
<4>[ 3069.977457] Modules linked in: i915(+) vgem snd_hda_codec_hdmi snd_hda_codec_realtek snd_hda_codec_generic x86_pkg_temp_thermal intel_powerclamp coretemp crct10dif_pclmul crc32_pclmul ghash_clmulni_intel snd_hda_codec snd_hwdep snd_hda_core snd_pcm r8169 mei_me mii prime_numbers mei i2c_hid pinctrl_geminilake pinctrl_intel [last unloaded: i915]
<4>[ 3069.977492] CPU: 1 PID: 15414 Comm: kworker/1:0 Tainted: G     U          4.14.0-CI-CI_DRM_3388+ #1
<4>[ 3069.977497] Hardware name: Intel Corp. Geminilake/GLK RVP1 DDR4 (05), BIOS GELKRVPA.X64.0062.B30.1708222146 08/22/2017
<4>[ 3069.977508] Workqueue: events output_poll_execute
<4>[ 3069.977512] task: ffff880177734e40 task.stack: ffffc90001fe4000
<4>[ 3069.977519] RIP: 0010:__lock_acquire+0x109/0x1b60
<4>[ 3069.977523] RSP: 0018:ffffc90001fe7bb0 EFLAGS: 00010002
<4>[ 3069.977526] RAX: 6b6b6b6b6b6b6b6b RBX: 0000000000000282 RCX: 0000000000000000
<4>[ 3069.977530] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff880170d4efd0
<4>[ 3069.977534] RBP: ffffc90001fe7c70 R08: 0000000000000001 R09: 0000000000000000
<4>[ 3069.977538] R10: 0000000000000000 R11: ffffffff81899609 R12: ffff880170d4efd0
<4>[ 3069.977542] R13: ffff880177734e40 R14: 0000000000000001 R15: 0000000000000000
<4>[ 3069.977547] FS:  0000000000000000(0000) GS:ffff88017fc80000(0000) knlGS:0000000000000000
<4>[ 3069.977551] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
<4>[ 3069.977555] CR2: 00007f7e8b7bcf04 CR3: 0000000003e0f000 CR4: 00000000003406e0
<4>[ 3069.977559] Call Trace:
<4>[ 3069.977565]  ? mark_held_locks+0x64/0x90
<4>[ 3069.977571]  ? _raw_spin_unlock_irq+0x24/0x50
<4>[ 3069.977575]  ? _raw_spin_unlock_irq+0x24/0x50
<4>[ 3069.977579]  ? trace_hardirqs_on_caller+0xde/0x1c0
<4>[ 3069.977583]  ? _raw_spin_unlock_irq+0x2f/0x50
<4>[ 3069.977588]  ? finish_task_switch+0xa5/0x210
<4>[ 3069.977592]  ? lock_acquire+0xaf/0x200
<4>[ 3069.977596]  lock_acquire+0xaf/0x200
<4>[ 3069.977600]  ? __mutex_lock+0x5e9/0x9b0
<4>[ 3069.977604]  _raw_spin_lock+0x2a/0x40
<4>[ 3069.977608]  ? __mutex_lock+0x5e9/0x9b0
<4>[ 3069.977612]  __mutex_lock+0x5e9/0x9b0
<4>[ 3069.977616]  ? drm_fb_helper_hotplug_event.part.19+0x16/0xa0
<4>[ 3069.977621]  ? drm_fb_helper_hotplug_event.part.19+0x16/0xa0
<4>[ 3069.977625]  drm_fb_helper_hotplug_event.part.19+0x16/0xa0
<4>[ 3069.977630]  output_poll_execute+0x8d/0x180
<4>[ 3069.977635]  process_one_work+0x22e/0x660
<4>[ 3069.977640]  worker_thread+0x48/0x3a0
<4>[ 3069.977644]  ? _raw_spin_unlock_irqrestore+0x4c/0x60
<4>[ 3069.977649]  kthread+0x102/0x140
<4>[ 3069.977653]  ? process_one_work+0x660/0x660
<4>[ 3069.977657]  ? kthread_create_on_node+0x40/0x40
<4>[ 3069.977662]  ret_from_fork+0x27/0x40
<4>[ 3069.977666] Code: 8d 62 f8 c3 49 81 3c 24 e0 fa 3c 82 41 be 00 00 00 00 45 0f 45 f0 83 fe 01 77 86 89 f0 49 8b 44 c4 08 48 85 c0 0f 84 76 ff ff ff <f0> ff 80 38 01 00 00 8b 1d 62 f9 e8 01 45 8b 85 b8 08 00 00 85
<1>[ 3069.977707] RIP: __lock_acquire+0x109/0x1b60 RSP: ffffc90001fe7bb0
<4>[ 3069.977712] ---[ end trace 4ad012eb3af62df7 ]---

In order to keep the dev_priv->ifbdev alive after failure, we have to
avoid the free and leave it empty until we unload the module (which is
less than ideal, but a necessary evil for simplicity). Then we can use
intel_fbdev_sync() to serialise the hotplug event with the configuration.
The serialisation between the two was removed in commit 934458c2
("Revert "drm/i915: Fix races on fbdev""), but the use after free is much
older, commit 366e39b4 ("drm/i915: Tear down fbdev if initialization
fails")

Fixes: 366e39b4 ("drm/i915: Tear down fbdev if initialization fails")
Fixes: 934458c2 ("Revert "drm/i915: Fix races on fbdev"")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Reviewed-by: NLukas Wunner <lukas@wunner.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20171125194155.355-1-chris@chris-wilson.co.uk

We should be consistent on naming of similar definitions.
Signed-off-by: NMichal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171124170239.29360-1-michal.wajdeczko@intel.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Chris has discovered that RC6, RC6p and RC6pp counters are mutually
exclusive, and even that on some SNB SKUs you get RC6p increasing, and on
the others RC6.

Furthermore RC6p and RC6pp were only present starting from GEN6 until,
GEN7, not including Haswell.

All this combined makes it questionable whether we need to reserve new ABI
for these counters. One idea was to just combine them all under the RC6
counter to simplify things for userspace. So that is what this patch does.
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Suggested-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171124171331.17981-1-tvrtko.ursulin@linux.intel.com