This driver implements support for iBT2.1 Bluetooth controller embedded
in the AG620 communication combo. The controller needs to be configured
with bddata and can be patched with a binary patch file (pbn).
These operations are performed in manufacturing mode.
Signed-off-by: NLoic Poulain <loic.poulain@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch adds a missing reg for writeable stuff for regmap.

Cc: Alan Ott <alan@signal11.us>
Signed-off-by: NAlexander Aring <aar@pengutronix.de>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch force always to set "is_tx_from_off", when calibration
timeout was not occurred. In case of error handling the is_tx_from_off
can be inside in an invalid state.
Signed-off-by: NAlexander Aring <aar@pengutronix.de>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The resource "ctx" can be still used by at86rf230_async_state_change, we
need to free it at the complete handler of the async state change to
avoid a use after free.
Signed-off-by: NAlexander Aring <aar@pengutronix.de>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

T: Bus=01 Lev=01 Prnt=01 Port=04 Cnt=02 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0489 ProdID=e095 Rev=00.01
C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

This device requires ar3k/AthrBT_0x31010100.dfu and
ar3k/ramps_0x31010100_40.dfu firmware files that are not in
linux-firmware yet.

BugLink: https://bugs.launchpad.net/bugs/1542944Signed-off-by: NDmitry Tunin <hanipouspilot@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org

If the call to request_firmware() fails in btbcm_setup_patchram(),
the BCM chip will be operating with its default firmware.

In this case, btbcm_setup_patchram() should not return immediately
but instead should skip to btbcm_check_bdaddr() and quirk setup.
Signed-off-by: NPetri Gynther <pgynther@google.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Recent macbooks (early 2015) with BCM43241 use this ACPI ID. Add it to the
list of supported devices.
Reported-by: NLeif Liddy <leif.liddy@gmail.com>
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This ACPI ID is used at least by HP for their Omni 10 5600eg tablet.
Signed-off-by: NJ.J. Meijer <jjmeijer88@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

T: Bus=03 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=13d3 ProdID=3395 Rev=00.01
C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

BugLink: https://bugs.launchpad.net/bugs/1542564Reported-and-tested-by: NChristopher Simerly <kilikopela29@gmail.com>
Signed-off-by: NDmitry Tunin <hanipouspilot@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org

A return value of the intel_wait_booting() function compared with
a constant ETIMEDOUT instead of -ETIMEDOUT.
Signed-off-by: NAnton Protopopov <a.s.protopopov@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Fixed a coding style issue. Added a blank link after declaration.
Signed-off-by: NBhumika Goyal <bhumirks@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

We were changing return values and accidentally made
rocker_world_port_obj_vlan_add() into a no-op.

Fixes: fccd84d4 ('rocker: return -EOPNOTSUPP for undefined world ops')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While building keystone_defconfig of arm we are getting build failure
with the error:

drivers/net/ethernet/ti/netcp_core.c:1846:31: error: invalid type argument of '->' (have 'struct tc_to_netdev')
  if (handle != TC_H_ROOT || tc->type != TC_SETUP_MQPRIO)
                               ^
drivers/net/ethernet/ti/netcp_core.c:1851:35: error: invalid type argument of '->' (have 'struct tc_to_netdev')
      (dev->real_num_tx_queues < tc->tc))
                                   ^
drivers/net/ethernet/ti/netcp_core.c:1855:8: error: invalid type argument of '->' (have 'struct tc_to_netdev')
  if (tc->tc) {
        ^
drivers/net/ethernet/ti/netcp_core.c:1856:28: error: invalid type argument of '->' (have 'struct tc_to_netdev')
   netdev_set_num_tc(dev, tc->tc);
                            ^
drivers/net/ethernet/ti/netcp_core.c:1857:21: error: invalid type argument of '->' (have 'struct tc_to_netdev')
   for (i = 0; i < tc->tc; i++)
                     ^
drivers/net/ethernet/ti/netcp_core.c: At top level:
drivers/net/ethernet/ti/netcp_core.c:1879:2: warning: initialization from incompatible pointer type
  .ndo_setup_tc  = netcp_setup_tc,
  ^

The callback of ndo_setup_tc should be:
int (*ndo_setup_tc)(struct net_device *dev, u32 handle, __be16 protocol,
                    struct tc_to_netdev *tc);

But we missed marking the last argument as a pointer.

Fixes: 16e5cc64 ("net: rework setup_tc ndo op to consume general tc operand")
CC: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NSudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Current initialization sequence is lacking, causing some configurations
to fail.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The phy's firmware version isn't being parsed properly as it's
currently parsed like the rest of the 848xx phys.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There's a problem in current 84833 phy configuration -
in case 1Gb link is configured and jumbo-sized packets are being
used, device will experience RX crc errors.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, when link is using KR2 it cannot be forced to any speed other
than 20g.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.om>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

FW hsi contains regpairs, mostly for 64-bit address representations.
Since same paradigm is applied each time a regpair is filled, this
introduces a new utility macro for setting such regpairs.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Each configuration element send via ramrod requires a Slow Path Queue
entry. This slightly changes the way such an entry is configured, but
contains mostly semantic changes [where more parameters are gathered
in a sub-struct instead of being directly passed].
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Due to HW design, some of the memories are wide-bus and access to those
needs to be sequentialized on a per-HW-block level; Read/write to a
given HW-block might break other read/write to wide-bus memory done at
~same time.

Status blocks initialization in CAU is done into such a wide-bus memory.
This moves the initialization into using DMAE which is guaranteed to be
safe to use on such memories.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Initial driver submission used GFP_ATOMIC almost inclusively when
allocating memory. We now remedy this point, using GFP_KERNEL where
it's possible.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1. scope correction for few functions that are used in single file.
2. Adjust variables that are used in fast-path to fit into single cacheline
3. Update rcv_frame() to skip shared check for frames coming over wire
Signed-off-by: NMahesh Bandewar <maheshb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mode argument was erronusly defined as u32 but it has always
been u16. Also use ipvlan_set_mode() helper to set the mode instead
of assigning directly. This should avoid future erronus assignments /
updates.
Signed-off-by: NMahesh Bandewar <maheshb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Scrub skb before hitting the iptable hooks to ensure packets hit
these hooks. Set the xnet param only when the packet is crossing the
ns boundry so if the IPvlan slave and master belong to the same ns,
the param will be set to false.
Signed-off-by: NMahesh Bandewar <maheshb@google.com>
CC: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dm9000 driver doesn't work in at least one device-tree
configuration, spitting an error message on irq resource :
[    1.062495] dm9000 8000000.ethernet: insufficient resources
[    1.068439] dm9000 8000000.ethernet: not found (-2).
[    1.073451] dm9000: probe of 8000000.ethernet failed with error -2

The reason behind is that the interrupt might be provided by a gpio
controller, not probed when dm9000 is probed, and needing the probe
deferral mechanism to apply.

Currently, the interrupt is directly taken from resources. This patch
changes this to use the more generic platform_get_irq(), which handles
the deferral.

Moreover, since commit Fixes: 7085a740 ("drivers: platform: parse
IRQ flags from resources"), the interrupt trigger flags are honored in
platform_get_irq(), so remove the needless code in dm9000.
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Acked-by: NMarcel Ziswiler <marcel@ziswiler.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: NSergei Ianovich <ynvich@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fix incorrect indexing of dev->dev_addr[] when copying the MAC address
of FMV-J182 at buf[5].
Signed-off-by: NKen Kawasaki <ken_kawasaki@nifty.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change makes it so that if UDP CSUM is not specified we will default
to enabling it.  The main motivation behind this is the fact that with the
use of outer checksum we can greatly improve the performance for VXLAN
tunnels on devices that don't know how to parse tunnel headers.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Acked-by: NTom Herbert <tom@herbertland.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change makes it so that if UDP CSUM is not specified we will default
to enabling it.  The main motivation behind this is the fact that with the
use of outer checksum we can greatly improve the performance for GENEVE
tunnels on hardware that doesn't know how to parse them.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Acked-by: NTom Herbert <tom@herbertland.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Device emulation supports max size of 4096.
Signed-off-by: NShrikrishna Khare <skhare@vmware.com>
Signed-off-by: NBhavesh Davda <bhavesh@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SW data field in descriptor can be used by software to hold private
data for the driver. As there are 4 words available for this purpose,
use separate macros to place it or retrieve the same to/from
descriptors. Also do type cast of data types accordingly.

Cc: Wingman Kwok <w-kwok2@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Grygorii Strashko <grygorii.strashko@ti.com>
CC: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rename the pad to sw_data as per description of this field in the hardware
spec(refer sprugr9 from www.ti.com). Latest version of the document is
at http://www.ti.com/lit/ug/sprugr9h/sprugr9h.pdf and section 3.1
Host Packet Descriptor describes this field.

Define and use a constant for the size of sw_data field similar to
other fields in the struct for desc and document the sw_data field
in the header. As the sw_data is not touched by hw, it's type can be
changed to u32.

Rename the helpers to match with the updated dma desc field sw_data.

Cc: Wingman Kwok <w-kwok2@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Grygorii Strashko <grygorii.strashko@ti.com>
CC: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The commit 89907779 ("netcp: try to reduce type confusion in
descriptors") introduces a regression in Kernel 4.5-rc1 and it breaks
get/set_pad_info() functionality.

The TI NETCP driver uses pad0 and pad1 fields of knav_dma_desc to
store DMA/MEM buffer pointer and buffer size respectively. And in both
cases for Keystone 2 the pointer type size is 32 bit regardless of
LAPE enabled or not, because CONFIG_ARCH_DMA_ADDR_T_64BIT originally
is not expected to be defined.

Unfortunately, above commit changed buffer's pointers save/restore
code (get/set_pad_info()) and added intermediate conversation to u64
which works incorrectly on 32bit Keystone 2 and causes TI NETCP driver
crash in RX/TX path due to "Unable to handle kernel NULL pointer"
exception. This issue was reported and discussed in [1].

Hence, fix it by partially reverting above commit and restoring
get/set_pad_info() functionality as it was before.

[1] https://www.mail-archive.com/netdev@vger.kernel.org/msg95361.html
Cc: Wingman Kwok <w-kwok2@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
CC: David Laight <David.Laight@ACULAB.COM>
CC: Arnd Bergmann <arnd@arndb.de>
Reported-by: NFranklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the problem that more CAN messages could be sent to the
interface as could be send on the CAN bus. This was more likely for slow baud
rates. The sleeping _start_xmit was woken up in the _write_bulk_callback. Under
heavy TX load this produced another bulk transfer without checking the
free_slots variable and hence caused the overflow in the interface.
Signed-off-by: NGerhard Uttenthaler <uttenthaler@ems-wuensche.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

The patch adds support for IFI CAN/FD controller [1]. This driver
currently supports sending and receiving both standard CAN and new
CAN/FD frames. Both ISO and BOSCH variant of CAN/FD is supported.

[1] http://www.ifi-pld.de/IP/CANFD/canfd.htmlSigned-off-by: NMarek Vasut <marex@denx.de>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Just sort the drivers in the Makefile, no functional change.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Sort the drivers that are directly listed in the Kconfig alphabetically, no
functional change.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Sort the Kconfig includes, no functional change.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Technologic Systems provides an IP compatible with the SJA1000,
instantiated in an FPGA. Because of some bus widths issue, access to
registers is made through a "window" that works like this:

    base + 0x0: address to read/write
    base + 0x2: 8-bit register value

This commit adds a new compatible device, "technologic,sja1000", with
read and write functions using the window mechanism.
Signed-off-by: NDamien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>