The driver configures the IDLE condition to interrupt the SDMA engine.
Since the SDMA UART ROM script doesn't clear the IDLE bit itself, this
caused repeated 1-byte DMA transfers, regardless of available data in the
RX FIFO. Also, when returning due to the IDLE condition, the UART ROM
script already increased its counter, causing residue to be off by one.

This patch clears the IDLE condition to avoid repeated 1-byte DMA transfers
and decreases count by when the DMA transfer was aborted due to the IDLE
condition, fixing serial transfers using DMA on i.MX6Q.
Reported-by: NPeter Seiderer <ps.report@gmx.net>
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Tested-by: NFabio Estevam <fabio.estevam@freescale.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 17b8f2a3 ("serial: imx: add support for half duplex rs485")
introduced the following build warning:

drivers/tty/serial/imx.c: In function 'imx_set_termios':
drivers/tty/serial/imx.c:1301:7: warning: suggest explicit braces to avoid ambiguous 'else' [-Wparentheses]

Add the suggested braces to avoid the build warning.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The transmitter is expected to be controlled by the UART's RTS pin.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Support for IRDA was added in 2009 in commit v2.6.31-rc1~399^2~2. There
are no in-tree users.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix indention, remove old address of the FSF, remove in-file changelog,
mention Freescale.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

There is no benefit in keeping this information in RAM when it's not
used any more, so better use function local variables instead.

These members are unused since c0d1c6b0 ("serial: imx: Fix the
reporting of interrupts")
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This if (0) exists since the driver was introduced in commit
c49bde83eb6a ([ARM PATCH] 1956/2: Re: Motorola i.MX serial driver)
back in 2004.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The writeable bits in the USR2 register are all "write 1 to
clear" so only write the bits that actually should be cleared.

Fixes: f1f836e4 ("serial: imx: Add Rx Fifo overrun error message")
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

UBRC is a read-only register, so we should not store and restore it inside
imx_flush_buffer().
Reported-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Make of_device_id array const.
Signed-off-by: NSanjeev Sharma <Sanjeev_Sharma@mentor.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When running an userspace program that does a 'tcflush(fd, TCIOFLUSH)' call
we still see the last received character in the URXD register afterwards.

Clear UCR2_SRST bit so that the UART FIFO is flushed properly.

Since UCR2_SRST also resets some UART registers, we need to save and restore
some of them.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Tested-by: NFugang Duan <B38611@freescale.com>
Acked-by: NJason Liu <r64343@freecale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When IGNPAR is set in termios->c_iflag,  characters with
framing errors should be ignored.
Signed-off-by: NEric Nelson <eric.nelson@boundarydevices.com>
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If IGNPAR/INPCK are clear in termios->c_iflag,  characters
received with parity or framing errors should be preserved
and passed to the upper layers of the tty stack.

Specifically, the decision of whether to set the character
value to zero should be made by n_tty.c/n_tty_receive_parity_error().
Signed-off-by: NEric Nelson <eric.nelson@boundarydevices.com>
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds Software flow control support in DMA mode.
Signed-off-by: NJiada Wang <jiada_wang@mentor.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

After send out x_char in UART driver, x_char needs to be cleared
by UART driver itself, otherwise data in TXFIFO can no longer be
sent out.
Also tx counter needs to be increased to keep track of correct
number of transmitted data.
Signed-off-by: NJiada Wang <jiada_wang@mentor.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Other than enable Receiver Overrun Interrupt Enable (UCR4_OREN)
in start_tx interface, UCR4_OREN should be enabled before enable
of Receiver.
Signed-off-by: NJiada Wang <jiada_wang@mentor.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Start rx_dma once RXFIFO is not empty that can avoid dma request lost
and causes data delay issue.
Signed-off-by: NRobin Gong <b38343@freescale.com>
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

DMA mode for UART can be used even w/o HW flow control with RTS/CTS.
So it need to be initialized and enabled earlier.
Signed-off-by: NAnton Bondarenko <anton_bondarenko@mentor.com>
Signed-off-by: NJiada Wang <jiada_wang@mentor.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Terminating the DMA, make sure the interrupt is disabled, too.
This fixes random kernel Oops due to dma_tx_call() called for
invalid transmissions.

If we disable the TDMAEN, make sure it's enabled again if a TX
DMA is started.
Signed-off-by: NJiada Wang <jiada_wang@mentor.com>
Signed-off-by: NDirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently in dma_tx_callback(), no matter if there is still
remaining data pending in circle buffer or not, DMA transmit
will be terminated.

This will result in some data never get transmitted.
In order to fix this issue, call imx_dma_tx() again in
dma_tx_callback, when there is pending data and uart hasn't
been stopped.
Signed-off-by: NJiada Wang <jiada_wang@mentor.com>
Signed-off-by: NDirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 2ad28e3e.

Instead of always wake up write_wait process in TX callback,
TX callback should call imx_dma_tx() again, and let imx_dma_tx
transfer the remaining data in circle buffer.

The issue with commit 2ad28e3e is, in case there is remaining
data in circle buffer, but no process is waiting on write_wait
queue, then as no following uart_write() will be called after
uart_write_wakeup(), thus cause data loss.

Moreover according to Documentation/serial/driver, uart_write_wakeup()
should be called in case the transmit buffer have dropped below
a threshold.
Signed-off-by: NJiada Wang <jiada_wang@mentor.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

To synchronize between dma_tx_callback() and imx_dma_tx() use the same
variable, dma_is_txing. This prevents any race between these two functions
and ensures that a new DMA can start only after the first has been
finished.

Before the new DMA can be set up, update the circular buffer logic, first.
Therefore, change dma_is_txing after that update, instead of before.

While doing this, in dma_tx_callback() extend the locking to dma_unmap_sg()
and the update of dma_is_txing.
Signed-off-by: NDirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

First, reformat the code to exit immediately. This allows us to add
more code in more readable format.

In case the TX DMA was still running, remove and disable it's resources.
Signed-off-by: NDirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In case dmaengine_prep_slave_sg() fails, add the missing dma_unmap_sg().
Signed-off-by: NDirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: NAnton Bondarenko <anton_bondarenko@mentor.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Inverting the logic of the if statement for the sg initialization
makes the if statement easier and better to read.

No functional change.
Signed-off-by: NDirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use imx_start_tx() just to enable the TX interrupt. It's the job of the
TX interrupt ISR to fill the transmit buffer, then. If the transmit buffer
is empty, the TX interrupt should be executed as soon as the start_tx()
enables the interrupt, so there is no reason for the extra
imx_transmit_buffer() call, here. Remove it.
Signed-off-by: NDirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: NAndy Lowe <andy_lowe@mentor.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Several places are accessing the UCR1 register without locking.
This probably will cause a race issue when another thread
is accessing the same register.
Add locking to preventing concurrent access of the UCR1 register.
Signed-off-by: NJiada Wang <jiada_wang@mentor.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add CREAD flag hanlding in set_termios and UART DMA mode
which ignores all received chars when CREAD flag cleared.
Signed-off-by: NJiada Wang <jiada_wang@mentor.com>
Signed-off-by: NAnton Bondarenko <anton_bondarenko@mentor.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When CONFIG_SERIAL_IMX_CONSOLE=n and CONFIG_CONSOLE_POLL=y we get the following
build warning:

drivers/tty/serial/imx.c:306:13: warning: 'imx_port_ucrs_save' defined but not used [-Wunused-function]
drivers/tty/serial/imx.c:315:13: warning: 'imx_port_ucrs_restore' defined but not used [-Wunused-function]

imx_port_ucrs_save/restore are only used under CONFIG_SERIAL_IMX_CONSOLE, so
their definitions should be also be protected only by CONFIG_SERIAL_IMX_CONSOLE.

This was detected when building 'allmodconfig'.
Reported-by: NOlof's autobuilder <build@lixom.net>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

For the console poll usage, .poll_init() will perform deeper hardware
initialization to ensure the serial port is always active.
Signed-off-by: NDaniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: NDirk Behme <dirk.behme@de.bosch.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Huang Shijie <b32955@freescale.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

imx_put_poll_char() has been simplified to remove the code to disable
interrupts. The present code can corrupt register state when re-entered
from FIQ handler.

Switch to _relaxed() MMIO functions (which are safe for polled I/O and
needed to avoid taking spin locks).
Signed-off-by: NDaniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: NDirk Behme <dirk.behme@de.bosch.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Huang Shijie <b32955@freescale.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

There is no real value in displaying "Serial: IMX driver" in every boot.

The uart_register_driver() can fail and even so the "Serial: IMX driver" will
be displayed, which is not really helpful.

This is particularly annoying when booting multi_v7_defconfig kernel on a SoC
that is not a i.MX and even though this message gets displayed.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When kzalloc() fails the core MM will already complain about it, so there is
no need to have the error message locally.

Remove the unneeded error message.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Instead of jumping to 'error_out1' label we can simplify the code and return the
error code directly.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

On a imx system with ttymxc0, ttymxc1 and ttymxc4 registered we see the
following output from 'cat /proc/interrupts':

$ cat /proc/interrupts
           CPU0
...
 58:         39       GIC  58  2020000.serial
 67:        115       GIC  67  21f8000.i2c

The only uart irq that appears is ttymxc0, which is the console.

As ttymxc1 and ttymxc4 will only have their irq registered at imx_startup(),
they are not shown right after probe.

Transmitting to ttymxc1 and ttymxc4 will cause their irqs to be registered, but
the output shows:

$ echo "111111" > /dev/ttymxc1
$ echo "444444" > /dev/ttymxc4
$ cat /proc/interrupts
           CPU0
...
 58:        150       GIC  58  2020000.serial
 59:          1       GIC  59
 62:          1       GIC  62
 67:        115       GIC  67  21f8000.i2c

,which misses printing the associated device address.

In order to fix this, register all the irqs inside the probe function via
devm_request_irq(), which will correctly report the serial interrupts associated
with their correspondent serial device and also helps simplyfing the code by
avoiding the calls to free_irq().

$ echo "111111" > /dev/ttymxc1
$ echo "444444" > /dev/ttymxc4
$ cat /proc/interrupts

	   CPU0
....
 58:        202       GIC  58  2020000.serial
 59:          1       GIC  59  21e8000.serial
 62:          1       GIC  62  21f4000.serial
 67:        115       GIC  67  21f8000.i2c
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

A platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The wait_event() makes the application hang for ever in the following case:
 [1] the hardware flow control is enabled.
 [2] the other end (or the remote end) is terminated, and the TX is still
     waiting for the hardware flow control signal to become asserted.

This patch fixes it by changing the wait_event to wait_event_interruptible.
Signed-off-by: NHuang Shijie <shijie8@gmail.com>
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When the uart port is suspending, the RX data is useless.
So in this case, we can terminate the RX DMA right now.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

when the 'CTSC' bit is negated. 'CTS' has no function when 'CTSC' is asserted.
0: The CTS pin is high (inactive)
1: The CTS pin is low (active)

For throttle, it needs to clear 'CTS' and 'CTSC' bits.
For unthrottle, it needs to enable 'CTS' and 'CTSC' bits.

The patch just fix the issue.
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NHuang Shijie <shijie8@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>