This SSP Controller supports a number of serial communication methods
and as such cannot be registered using of_register_spi_devices.
Instead we register it simply as a primecell device.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Enables the 3 UARTs found on a u8500 using DT.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Reviewed-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

This adds all devices that are normally present through the
u8500_init_machine function in the device tree as well, which
will duplicate the devices that are visible.

This will not do much by itself because the device from the
device tree are not matched by any device driver until they
are converted as well. The next step is to move over one
device at a time to actually be used from the device tree
instead of the hardcoded device using auxdata to pass the
correct platform_data.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

This lets us move over evertything to device tree one by one.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

This provides very basic Device Tree support for ST-Ericsson's
low-cost development platform, Snowball. If Device Tree for
ux500 is enabled and the correct board is configured within the
Device Tree blob, the correct *_init_machine() will be called.

This patch is based on some original work completed by:
  Niklas Hernaeus <niklas.hernaeus@linaro.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NNiklas Hernaeus <niklas.hernaeus@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

AB8500 GPIO1 is the base of AB8500 gpio number too.
Signed-off-by: NPhilippe Langlais <philippe.langlais@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

At the request of Arnd Bergmann this patch moves all SoC
platform devices found in sysfs from /sys/devices/platform to
/sys/devices/soc<SoCNum>/. It is believed as the devices are
SoC specific and a /sys/devices/soc node has recently
become available, that this would be a more appropriate place to
display the data.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

This patch provides a means for any device within ux500
platform code to allocate its own parent. This is particularly
prudent with the introduction of /sys/devices/socX, as a
device can now proclaim to be integral part of an SoC, rather
than a more generic platform device. Latter patches make good
use of this functionality.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

This moves all the header files related to the abx500 family into
a common include directory below mfd. From now on we place any
subchip header in that directory. Headers previously in e.g.
<linux/mfd/ab8500/gpio.h> get prefixed and are now e.g.
<linux/mfd/abx500/ab8500-gpio.h>. The top-level abstract interface
remains in <linux/mfd/abx500.h>.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Properly support the correct SDI-init sequence on the
ST-Ericsson HREFv60 and later boards in order to get
support for SD cards.
Signed-off-by: NStefan Nilsson XK <stefan.xk.nilsson@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Convert the ux500 platforms to be using the gic_handle_irq
function as their primary interrupt handler.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

Do more work in the per-machine init calls instead of customizing
each init call.
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The <[plat|mach]/gpio.h> file is included from upper directories
and deal with generic GPIO and gpiolib stuff. Break out the
platform and driver specific defines and functions into its own
header file.

Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Alessandro Rubini <rubini@unipv.it>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NNicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>

With SDI support for the Snowball we can boot from the
SD card.
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NRobert Marklund <robert.marklund@stericsson.com>

Based on work from Mathieu J. Poirier <mathieu.poirier@linaro.org>
For more information on snowball please visit
http://www.igloocommunity.orgSigned-off-by: NRobert Marklund <robert.marklund@stericsson.com>

This board now has complete regulation constraints and can turn
off unused regulators. For the moment we need to wire VAUX1
(V-DISPLAY rail) always on since it somehow affects the external
MMC.

Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This patch provides platform data for following
 - uart reset function to assist uart register lockup workaround

 - init/exit function to fix glitch in the tx pin in tty_open
	when tty port0 is opened a glitch is seen in the tx line
	of uart0. This happens in pl011_startup() when tx fifo
	interrupt is provoked into asserting.
	Now uart0 pins are enabled (alt function) only when init
	is complete and turned back to gpio when closed.
Signed-off-by: NShreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This specifies the new per-platform timeout per I2C bus and
switches the I2C buses to fast mode, and increase the FIFO
depth to 8 for reads and writes.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Adding two sets of I2C devices to the same bus doesn't quite work,
atleast not anymore. Stash one array and determine how much of it
shall be added instead.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: NLucas De Marchi <lucas.demarchi@profusion.mobi>

This registers the TPS61052 regulator to the ux500 MOP/HREF boards.

Cc: Samuel Ortiz <samuel.ortiz@intel.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Ola Lilja <ola.o.lilja@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This adds an ab8500 regulator initialization vector for the
HREF/MOP500 series of boards. This also sets the display
regulator to be on at boot so we don't loose our splash
screen when the board comes up.
Signed-off-by: NBengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This is the board support patch for ab8500 gpio driver
on mach-ux500.Patch implements 16 virtual
IRQ mapped to 16 interrupt capable AB8500 GPIOs.
Signed-off-by: NBibek Basu <bibek.basu@stericsson.com>
[Modify for header file placement]
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The regulators on the AB8500 have a lot of custom
hardware control settings pertaining to 8 external
signals, settings which are board-specific and need
be provided from the platform at startup.

Initialization added for regulators Vana, VextSupply1,
VextSupply2, VextSupply3, Vaux1, Vaux2, Vaux3, VTVout,
Vintcore12, Vaudio, Vdmic, Vamic1, Vamic2, VrefDDR.
Signed-off-by: NBengt Jonsson <bengt.g.jonsson@stericsson.com>
Reviewed-by: NRickard Andersson <rickard.andersson@stericsson.com>
Reviewed-by: NJonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The HREFv60 variant of the MOP500 family of boards remove the
external GPIO expander and route these pins back to some of the
readily available internal GPIO pins instead.

Based on a patch by Bibek Basu <bibek.basu@stericsson.com> for
an internal kernel version.

Cc: Bibek Basu <bibek.basu@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Split off pin definitions for the MOP500 board family to its
own file.
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This will configure the platform data for the PL011, PL022
and PL180 (derivate) PrimeCells found in the Ux500 to use DMA
with the generic DMA engine for DMA40.
Signed-off-by: NPer Forlin <per.forlin@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

- DMA tx and rx maps for usb channels are set to be configured at
  runtime
- GPIO configurations for usb are added
- MUSB is enabled with soc specific base address, irq and dma
  configurations
Signed-off-by: NMian Yousaf Kaukab <mian-yousaf.kaukab@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Signed-off-by: NPhilippe Langlais <philippe.langlais@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Proximity sensor is managed as an input event (SW_PROXIMITY).
Signed-off-by: NPhilippe Langlais <philippe.langlais@linaro.org>
[Named GPIO pin]
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The U8500 UIB contains a Synaptics RMI touchpanel and
a matrix keyboard via the TC35893 port expander device.
Signed-off-by: NSundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Add support for dynamic detection of the UIB used (at the cost of one i2c error
on the lesser-used UIB) and also provide an override via a command line
parameter if needed.
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: NSundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The ab8500 regulator board configuration is updated and put in an
array which can easily be used in the MFD board configuration. The
regulator board configuration is also added to the MFD
configuration in this patch.
Signed-off-by: NBengt Jonsson <bengt.g.jonsson@stericsson.com>
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: NSundar Iyer <sundar.iyer@stericsson.com>
[Minor fixups to GPIO enumerators]
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>

Move keylayouts to a dedicated file and plug these keylayouts
for input platform data. This will make addition of new and custom
keylayouts localized.
Signed-off-by: NSundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>

Add block identifier to be able to add multiple mfd clients
to the mfd core
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NSundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>

Most of the register layout, client IRQ numbers on the TC35892 is shared also
by other variants. Make this generic as tc3589x
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NSundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>

Acked-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NSundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>