wait_for_completion_timeout does not return negative values so the tests
for <= 0 are not needed and the case differentiation in the error handling
path unnecessary.
Signed-off-by: NNicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Recent commit
30c78167 ("ath10k:
set max_num_vdevs based on wmi op version")
skipped wmi-tlv case and left max_num_vdevs reset.
Make sure it is properly set.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

htt->max_throughput_mbps is not used anywhere.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Return a negative error code on failure.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
 { ... return ret; }
|
ret = 0
)
... when != ret = e1
    when != &ret
*if(...)
{
  ... when != ret = e2
      when forall
 return ret;
}
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This per-station debugfs entry helps to send delba in manual mode
for debugging purpose. It accepts tid, initiator and reason code
as inputs.

To send delba,

echo 0 1 37 >/sys/kernel/debug/ieee80211/phyX/netdev:wlanX/
	     stations/XX:XX:XX:XX:XX:XX/delba
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This per-station debugfs entry helps to send addba response in
manual mode for debugging purpose. It accepts tid and status code
as input arguments.

To send addba response,

echo 0 25 >/sys/kernel/debug/ieee80211/phyX/netdev:wlanX/
	   stations/XX:XX:XX:XX:XX:XX/addba_resp
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This per-station debugfs entry helps to send addba request in manual
mode. Need to pass two configuration parameters (tid, buffer size)
as input.

To send addba,

echo 1 32 >/sys/kernel/debug/ieee80211/phyX/netdev:wlanX/
	   stations/XX:XX:XX:XX:XX:XX/addba
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Add per station debugfs files when a station is added to mac80211's
station list. This helps to group peer specific debugfs entries
altogether. Right now this callback adds support to test aggregation
procedures (addba/addba_resp/delba) manually.

To enable automatic aggregation in target,
echo 0 >/sys/kernel/debug/ieee80211/phyX/netdev:wlanX/
	stations/XX:XX:XX:XX:XX:XX/aggr_mode

For manual mode,
echo 1 >/sys/kernel/debug/ieee80211/phyX/netdev:wlanX/
	stations/XX:XX:XX:XX:XX:XX/aggr_mode
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Add WMI support for sending delba request. This command is used for
debugging purpose.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Add WMI support for sending addba response manually. This command
is used for debugging purpose.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Add WMI support for sending addba request. This command is meant
for debugging purpose.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Add WMI support for clearing addba response before switching aggregation
mode (auto/manual) for debugging purpose.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This feature allows the FW to batch RX indications,
reducing the rate of host interrupt generation, which
in turn reduces CPU load. Currently, this is enabled
only for the 10.2 firmware.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

A value of zero indicates that 128B is the maximum
DMA request size for read/writes. But PCI cards based
on AR9880 can support 256B, so enable this for
the 10.2 firmware.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

kbuild reported a linking error:

ERROR: "devm_hwmon_device_register_with_groups"
[drivers/net/wireless/ath/ath10k/ath10k_core.ko] undefined!

Fix it by returning early and letting the compiler to optimise out the function
call.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

phymode should use 11b only if NO_OFDM flags is set.
Hence check up channel flag for NO_OFDM and set to
11b.
Signed-off-by: NPeter Oh <poh@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Assoc peer command contain information about NSS.
When we will get IEEE80211_RC_NSS_CHANGED we should
also send (re) assoc peer command to be sure firmware
will know about it and RC will work correctly.

This was found during code review.
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This fix TX problem when IBSS used in HT mode.
Before we used 6Mbps all the time for TX direction.
Reported-by: NYeoh Chun-Yeow <yeohchunyeow@gmail.com>
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Temperature sensor generates electrical analog voltage from temperature
of each chain. The analog voltage is converted to digital value through
ADC. For reading temperature values fom user space, hw monitoring device
is used.

Whenever the user requests for current temperature, the driver sends WMI
command and wait for response. For reading temperature,

cat /sys/class/ieee80211/phy*/device/hwmon/hwmon2/temp1_input
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Add WMI command support for reading temperature from the target and
corresponding WMI temperature event handler. The pdev_get_temperature
command is currently supported in 10.2 firmware alone.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Thermal cooling device support is added to control the temperature
by throttling the data transmission for the given duration. Throttling
is done using hw MAC quiet time setting. Period, duration and offset
from TBTT can be set up to quiet the MAC transmits for the required duty
cycle (% of quiet duration). The thermal device allows user to configure
duty cycle.

The quiet params are derived as follows.
	period = max(25TU, beacon interval / number of bss)
	duration = period * duty cycle / 100

Quiet mode can be disabled by setting the duty cycle to 0. The cooling
device can be found under /sys/class/thermal/cooling_deviceX/.
Corresponding soft link to this device can be found under phy folder.

/sys/class/ieee80211/phy*/device/cooling_device.

To set duty cycle as 40%,

echo 40 >/sys/class/ieee80211/phy*/device/cooling_device/cur_state
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Add WMI support to send pdev_set_quiet_mode command to target.
This will be used for thermal mitigation purpose.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

10.2.4 firmware uses bitmask in wmi_resource_config to configure
10.2 firmware features like airtime fairness and rx batch mode instead
of maintaining separete bool entry. This allows new features that can be
configure during init time without breaking backward compatibility.

kvalo: use WMI op version, bump up FW API to 4 to not break older versions of
ath10k
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The internal firmware version doesn't tell much to the user, it's more
informative to use that field to print the wmi op version.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

ATH10K_FW_FEATURE_WMI_10X should not be used for anymore as that's
now deprecated, instead use wmi op version.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

To make it easier to manage firmware differences, we should not use
ATH10K_FW_FEATURE_WMI_10X outside ath10k_core_init_firmware_features(). To
achieve that create new field ar->max_num_vdevs and set it based on wmi op
version.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Firmware doesn't allow precise tx rate control so
P2P wasn't entirely spec compliant (it was using
CCK rates in some cases).

The only way to make sure firmware doesn't use CCK
rates is to have a vdev with P2P subtype used for
scanning and tx. This can be done via a special
dedicated P2P device interface support.

This also removes the ancient hack from ath10k in
favor of p2pdev.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Per-vif bss_conf.ps should be used to configure
powersave.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Setting 0 ps timeout to firmware yields very poor
latency and traffic issues. This is the case when
multi-vif is active.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

To comply with WMM-PS the device shouldn't wake up
with a NullFunc frame pair when tx-ing. Instead PM
bit on each tx frame should be used.

To make this work correctly firmware needs to be
told to use a different STA PS wake threshold when
u-APSD is enabled.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Some firmware revisions need peer phymode to be
specified as MODE_11B when associating as station
to a 11b AP. Otherwise they can starve other
stations.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Setting fragmentation threshold has not been supported by
any of firmware versions, hence unregister the callback and
remove the function.
Signed-off-by: NPeter Oh <poh@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Introduce a new wmi interface controls noise floor (NF) calibration
period via debugfs as firmware has introduced it on v10.2.

It allows users to modify frequency of NF calibration in millisecond
and changes RSSI reporting frequency consequently.
Short calibration period will trigger more frequent NF calibration,
so that RSSI reported in receive frames is more realistic.

Till now calibration was done at 30 seconds.
Signed-off-by: NPeter Oh <poh@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

New pdev paramters have been added to firmware 10.2,
hence update wmi interfaces to sync with.
Signed-off-by: NPeter Oh <poh@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Latest main firmware branch introduced a new WMI
ABI called wmi-tlv. It is not a tlv strictly
speaking but something that resembles it because
it is ordered and may have duplicate id entries.

This prepares ath10k to support new hw.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Some functions can be shared across different WMI
ABIs. Make them public so different WMI backends
can use them from different source files in the
future.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Since the 10.x fw branch support was introduced it
became apparent ath10k will need to be able to
deal with different fw ABIs eventually.

The patch creates an abstraction for dealing with
command and event structures across different ABIs
and mostly gets rid of the
ATH10K_FW_FEATURE_WMI_10X flag usage.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This splits the actual event parsing into
intermediary structures to facilitate future
support of vastly different ABI WMI backends.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Better to have this in same place as other firmware interface handling.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Instead of using feature flags, add new 32 bit variable for managing different
WMI versions. This makes it firmware interface tests a bit less convoluted,
especially when we add one more interface.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>