Clean up EH speed down implementation.

* is_io boolean variable is replaced eflags.  is_io is ATA_EFLAG_IS_IO.

* Error categories now have names.

* Better comments.

* Reorder 5min and 10min rules in ata_eh_speed_down_verdict()

* Use local variable @link to cache @dev->link in ata_eh_speed_down()

These changes are to improve readability and ease further changes.
This patch doesn't introduce any behavior change.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Move ata_set_mode() to libata-eh.c.  ata_set_mode() is surely an EH
action and will be more tightly coupled with the rest of error
handling.  Move it to libata-eh.c.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Factor out ata_eh_schedule_probe() from ata_eh_handle_dev_fail() and
ata_eh_recover().  This is to improve maintainability and make future
changes easier.

In the previous revision, ata_dev_enabled() test was accidentally
dropped while factoring out.  This problem was spotted by Bartlomiej.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Implement protocol tests - ata_is_atapi(), ata_is_nodata(),
ata_is_pio(), ata_is_dma(), ata_is_ncq() and ata_is_data() and use
them to replace is_atapi_taskfile() and hard coded protocol tests.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Area for DFLAGs which are cleared on INIT is full.  Extend it by 8
bits.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

For intel ones, ahci unconditionally OR'd 0xf to PCS.  This isn't
correct for the following cases.

* ich6/7m's which only implement P0 and P2 (0xf works fine tho)

* ich8/9's which have six ports and needs 0x3f to enable all ports

This patch updates PCS programming such that...

* port_map determined by ahci_save_initial_config() is OR'd instead of 0xf

* PCS is updated only if necessary (there are turned off enable bits)

port_map is determined from PORTS_IMPL PCI register which is
implemented as write or write-once register.  If the register isn't
programmed, ahci automatically generates it from number of ports,
which is good enough for PCS programming.  ICH6/7M are probably the
only ones where non-contiguous enable bits are necessary && PORTS_IMPL
isn't programmed properly but they're proven to work reliably with 0xf
anyway.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Lots of work needed to bring it up to scratch but it does work so you can
now use the card. That makes it at least useful, especially as the other
cardbus cards are usually INIC162x which aren't yet supported well.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Jeff said he preferred that the SFF tf_load followed the spec and we
documented that anyone who needed different overrode it, rather than it
using the ->check_status methods. No driver relies on the current behaviour.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

I believe this version meets all Sergei's objections

Correct the logic for when we issue a set features for transfer mode

- If the device has IORDY and the controller has IORDY - set the mode
- If the device has IORDY and the controller does not - turn IORDY off
- If neither has IORDY do nothing
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

ACPI spec (ver 3.0a, p289) requires IDE power on/off executes ACPI _PSx
methods. As recently most PATA drivers use libata, this patch adds _PSx
method support in libata. ACPI spec doesn't mention if SATA requires the
same _PSx method.
Signed-off-by: NShaohua Li <shaohua.li@intel.com>
Acked-by: NLen Brown <len.brown@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Historically word 48 in the identify data was used to mean 32bit I/O
was supported for VLB IDE etc. ATA8 reassigns this word to the Trusted
Computing Group, where it is used for TCG features. This means that
an ATA8 TCG drive is going to trigger 32bit I/O on some systems which
will be funny.

Anyway we need to sort this out ready for ATA8 so:
- Reorder the ata.h header a bit so the ata_version function occurs early
  in it
- Make dword_io check the ATA version
- Add an ATA8 version checking TCG presence test

While we are at it the current drafts have a flaw where it may not be
possible to disable TCG features at boot (and opt out of the trusted
model) as TCG intends because it relies on presence of a different
optional feature (DCS). Handle this in software by refusing the TCG
commands if libata.allow_tpm is not set. (We must make it possible
as some environments such as proprietary VDR devices will doubtless
want to use it to lock up content)

Finally as with CPRM print a warning so that the user knows they may
not be able to full access and use the device.
Signed-off-by: NAlan Cox <alan@redhat.com>

Add Toshiba Satellite R20 and Tecra M6 to broken suspend list.  Matt
Piermarini reported and provided the M6 patch.  This is from OSDL bug 7780.
Signed-off-by: NPeter Schwenke <peter@bluetoad.com.au>
Cc: Matt Piermarini <mattpiermarini@yahoo.com>
Acked-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

When we set the MFGPT timer tick, there is a chance that we'll
immediately assert an event.  If for some reason the IRQ routing
for this clock has been setup for some other purpose, then we
could end up firing an interrupt into the SMM handler or worse.

This rearranges the timer tick init function to initalize the handler
before we set up the MFGPT clock to make sure that even if we get
an event, it will go to the handler.

Furthermore, in the handler we need to make sure that we clear the
event, even if the timer isn't running.
Signed-off-by: NJordan Crouse <jordan.crouse@amd.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NIngo Molnar <mingo@elte.hu>
Tested-by: NArnd Hannemann <hannemann@i4.informatik.rwth-aachen.de>

Fix typo in arch/powerpc/boot/flatdevtree_env.h.
There is no Documentation/networking/ixgbe.txt.

README.cycladesZ is now in Documentation/.
wavelan.p.h is now in drivers/net/wireless/.
HFS.txt is now Documentation/filesystems/hfs.txt.
OSS-files are now in sound/oss/.
Signed-off-by: NJohann Felix Soden <johfel@users.sourceforge.net>
Acked-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'release' of git://lm-sensors.org/kernel/mhoffman/hwmon-2.6:
  hwmon: (it87) request only Environment Controller ports

* git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86:
  Revert "x86: fix NMI watchdog & 'stopped time' problem"

* git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched:
  sched: group scheduler, set uid share fix

rcu_online_cpu() should be __cpuinit instead of __devinit.

WARNING: vmlinux.o(.text+0x4b6d5): Section mismatch: reference to .init.text: (between 'rcu_cpu_notify' and 'wakeme_after_rcu')
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Acked-by: NIngo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The extra rom[0] check is flagging valid temperatures as invalid when
there is already a CRC data transmission check.

w1_therm_read_bin()
	if (rom[8] == crc && rom[0])
		verdict = 1;

Requiring rom[0] to be non-zero will flag as invalid temperature
conversions when the low byte is zero, specifically the temperatures 0C,
16C, 32C, 48C, -16C, -32C, and -48C.

The CRC check is produced on the device for the previous 8 bytes and is
required to ensure the data integrity in transmission.  I don't see why the
extra check for rom[0] being non-zero is in there.  Evgeniy Polyakov didn't
know either.  Just for a check I unplugged the sensor, executed a
temperature conversion, and read the results.  The read was all ff's, which
also failed the CRC, so it doesn't need to protect against a disconnected
sensor.

I have more extensive patches in the work, but these two trivial ones will
do for today.  I would like to hear from people who use the ds2490 USB to
one wire dongle.  1 if you would be willing to test the patches as I
currently only have the one sensor on a short parisite powered wire, 2 if
there is any cheap sources for the ds2490.
Signed-off-by: NDavid Fries <david@fries.net>
Acked-by: NEvgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Correct the decoding of negative C temperatures.  The code did a binary OR
of two bytes to make a 16 bit value, but assignd it to an integer.  This
caused the value to not be sign extended and to loose that it was a
negative number in the assignment.

Before the patch (in my freezer),
	w1_slave
	ed fe 4b 46 7f ff 03 10 e4 : crc=e4 YES
	ed fe 4b 46 7f ff 03 10 e4 t=4078
With the patch,
	e3 fe 4b 46 7f ff 0d 10 81 : crc=81 YES
	e3 fe 4b 46 7f ff 0d 10 81 t=-17
Signed-off-by: NDavid Fries <david@fries.net>
Acked-by: NEvgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The IT8705F and related parts are Super I/O controllers that contain
many separate devices.

Some BIOSes describe IT8705F I/O port usage under a motherboard device
(PNP0C02) with overlapping regions, e.g., 0x290-0x29f and 0x290-0x294.

The it87 driver supports only the Environment Controller, which requires
only two ISA ports, but it used to request an eight-port range.  If that
range exceeds a range reported by the BIOS, as 0x290-0x297 would, the
request fails, and the it87 driver cannot claim the device.

This patch makes the it87 driver request only the two ports used for the
Environment Controller device.

Systems where this problem has been reported:
    Gigabyte GA-K8N Ultra 9
    Gigabyte M56S-S3
    Gigabyte GA-965G-DS3

Kernel bug reports:
    http://bugzilla.kernel.org/show_bug.cgi?id=9514
    http://lkml.org/lkml/2007/12/4/466

Related change:
    http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commitdiff;h=a7839e960675b549f06209d18283d5cee2ce9261

    The patch above increases the number of PNP port resources we support.
    Prior to this patch, we ignored some port resources, which masked the
    it87 problem.
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

setting cpu share to 1 causes hangs, as reported in:

    http://bugzilla.kernel.org/show_bug.cgi?id=9779

as the default share is 1024, the values of 0 and 1 can indeed
cause problems. Limit it to 2 or higher values.

These values can only be set by the root user - but still it
makes sense to protect against nonsensical values.
Signed-off-by: NIngo Molnar <mingo@elte.hu>

This reverts commit d4d25dec.

It tried to fix long standing bugzilla entries, but the solution was
reported to break other systems. The reporter of

http://bugzilla.kernel.org/show_bug.cgi?id=9791

tracked it down to this commit and confirmed that reverting the patch
restores the correct behaviour. It's too late in the release cycle to
find a better solution than reverting the commit to avoid regressions.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NIngo Molnar <mingo@elte.hu>

Change two occurances of "behavour" to "behaviour".
Signed-off-by: NLinus Nilsson <lajnold@acc.umu.se>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/selinux-2.6:
  selinux: fix memory leak in netlabel code

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  [ICMP]: ICMP_MIB_OUTMSGS increment duplicated
  [IPV6]: RFC 2011 compatibility broken
  [IPV6]: ICMP6_MIB_OUTMSGS increment duplicated
  [NET]: rtnl_link: fix use-after-free
  [AF_KEY]: Fix skb leak on pfkey_send_migrate() error
  [ATM] atm/suni.c: Fix section mismatch.
  [ATM] atm/idt77105.c: Fix section mismatch.
  [IrDA]: af_irda memory leak fixes
  [NEIGH]: Revert 'Fix race between neigh_parms_release and neightbl_fill_parms'
  [NETFILTER]: bridge-netfilter: fix net_device refcnt leaks
  [IPV6] ROUTE: Make sending algorithm more friendly with RFC 4861.
  [IPV4] FIB_HASH : Avoid unecessary loop in fn_hash_dump_zone()
  [NET]: Fix interrupt semaphore corruption in Intel drivers.
  [IPV4] fib_trie: fix duplicated route issue
  [IPV4] fib_hash: fix duplicated route issue
  [IPV6]: Mischecked tw match in __inet6_check_established.
  rfkill: call rfkill_led_trigger_unregister() on error

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  tc35815: Use irq number for tc35815-mac platform device id
  [MIPS] Malta: Fix reading the PCI clock frequency on big-endian
  [MIPS] SMTC: Fix build error.

In linux-2.6.24-rc1, security/commoncap.c:cap_inh_is_capped() was
introduced. It has the exact reverse of its intended behavior. This
led to an unintended privilege esculation involving a process'
inheritable capability set.

To be exposed to this bug, you need to have Filesystem Capabilities
enabled and in use. That is:

- CONFIG_SECURITY_FILE_CAPABILITIES must be defined for the buggy code
  to be compiled in.

- You also need to have files on your system marked with fI bits raised.
Signed-off-by: NAndrew G. Morgan <morgan@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@akpm@linux-foundation.org>

Fix line length calculation. var->width is the size of the display in mm. We
like to use the pixel size.

Without this fix, dynamic (fbset) based resolution and depths changes with
s3c2410_fb don't work at all.

Spotted by john cass <johnpcass@yahoo.com>
Signed-off-by: NStefan Schmidt <stefan@openmoko.org>
Signed-off-by: NHarald Welte <laforge@openmoko.org>
Acked-by: NBen Dooks <ben-linux@fluff.org>
Acked-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@akpm@linux-foundation.org>

Signed-off-by: NCyrill Gorcunov <gorcunov@gmail.com>
Acked-by: NJesper Nilsson <jesper.nilsson@axis.com>
Cc: Mikael Starvik <starvik@axis.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@akpm@linux-foundation.org>

The caller is __cpuinit.
Also, this code block and its caller are inside #ifdef CONFIG_HOTPLUG_CPU
blocks, so this code should reflect that config symbol's usage.

WARNING: vmlinux.o(.text+0x4252f): Section mismatch: reference to .init.text: (between 'timer_cpu_notify' and 'msleep')
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@akpm@linux-foundation.org>

Fix section mismatch in hrtimer.c:

WARNING: vmlinux.o(.text+0x50c61): Section mismatch: reference to .init.text: (between 'hrtimer_cpu_notify' and 'down_read_trylock')

Noticed by Johannes Berg and confirmed by Sam Ravnborg.
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@akpm@linux-foundation.org>

If we get a data URB back from the hardware after we have put the tty to
bed we go kaboom.  Fortunately all we need to do is process the URB without
trying to ram its contents down the throat of an ex-tty.
Signed-off-by: NAlan Cox <alan@redhat.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@akpm@linux-foundation.org>

The tc35815-mac platform device used a pci bus number and a devfn to
identify its target device, but the pci bus number may vary if some
bus-bridges are found.  Use irq number which is be unique for embedded
controllers.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The JMPRS register on Malta boards keeps a 32-bit CPU-endian
value. The readw() function assumes that the value it reads is a
little-endian 16-bit number. Therefore, using readw() to obtain
the value of the JMPRS register is a mistake. This error leads
to incorrect reading of the PCI clock frequency on big-endian
during board start-up.

Change readw() to __raw_readl().

This was tested by injecting a call to printk() and verifying
that the value of the jmpr variable was consistent with current
setting of the JP4 "PCI CLK" jumper.
Signed-off-by: NDmitri Vorobiev <dmitri.vorobiev@gmail.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Fix compile warning (which becomes compile error due to -Werror).  Type of
argument "flags" for spin_lock_irqsave() was incorrect in some functions.
Signed-off-by: NFrank Rowand <frank.rowand@am.sony.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Fix a memory leak in security_netlbl_sid_to_secattr() as reported here:
 * https://bugzilla.redhat.com/show_bug.cgi?id=352281Signed-off-by: NPaul Moore <paul.moore@hp.com>
Signed-off-by: NJames Morris <jmorris@namei.org>

Commit "96793b48" (Add ICMPMsgStats
MIB (RFC 4293)) made a mistake.

In that patch, David L added a icmp_out_count() in
ip_push_pending_frames(), remove icmp_out_count() from
icmp_reply(). But he forgot to remove icmp_out_count() from
icmp_send() too.  Since icmp_send and icmp_reply will call
icmp_push_reply, which will call ip_push_pending_frames, a duplicated
increment happened in icmp_send.

This patch remove the icmp_out_count from icmp_send too.
Signed-off-by: NWang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The snmp6 entry name was changed, and it broke compatibility
to RFC 2011.
Signed-off-by: NWang Chen <wangchen@cn.fujitsu.com>
Acked-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>