No longer needed and causes build breakage.
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Add the 8.0 GT/s speed.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Take advantage of some gaps in the table to fit in support for AGP speeds.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Both PCIe and PCI-X bridges report their secondary bus speed in their
respective capabilities.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Move the max_bus_speed and cur_bus_speed into the pci_bus.  Expose the
values through the PCI slot driver instead of the hotplug slot driver.
Update all the hotplug drivers to use the pci_bus instead of their own
data structures.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

These enums must not overlap anyway, since we only have a single
pci_bus_speed_strings array.  Use a single enum, and move it to
pci.h.  Add 'SPEED' to the pcie names to make it clear what they are.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The Alternate Routing-ID Interpretation capability allows a single device
to have up to 256 functions.  They can be populated sparsely, so the
current technique of scanning every eighth function is not guaranteed
to find them all.  By introducing a 'next_fn' function pointer, we can
use the linked list of functions in the ARI capability to scan all the
functions which exist.

We can then speed up the pci_scan_slot by skipping the scan of subsequent
devfns for PCIe devices which are the direct children of Root Ports or
Downstream Ports.  These devices are only permitted to implement device
0, unless they are ARI devices, in which case they'll be scanned by the
ARI code above.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The new cs5535-* drivers use PCI header config info rather than MSRs to
determine the memory region to use for things like GPIOs and MFGPTs.  As
anticipated, we've run into a buggy BIOS:

[    0.081818] pci 0000:00:14.0: reg 10: [io  0x6000-0x7fff]
[    0.081906] pci 0000:00:14.0: reg 14: [io  0x6100-0x61ff]
[    0.082015] pci 0000:00:14.0: reg 18: [io  0x6200-0x63ff]
[    0.082917] pci 0000:00:14.2: reg 20: [io  0xe000-0xe00f]
[    0.083551] pci 0000:00:15.0: reg 10: [mem 0xa0010000-0xa0010fff]
[    0.084436] pci 0000:00:15.1: reg 10: [mem 0xa0011000-0xa0011fff]
[    0.088816] PCI: pci_cache_line_size set to 32 bytes
[    0.088938] pci 0000:00:14.0: address space collision: [io 0x6100-0x61ff] already in use
[    0.089052] pci 0000:00:14.0: can't reserve [io  0x6100-0x61ff]

This is a Soekris board, and its BIOS sets the size of the PCI ISA bridge
device's BAR0 to 8k.  In reality, it should be 8 bytes (BAR0 is used for
SMBus stuff).  This quirk checks for an incorrect size, and resets it
accordingly.
Signed-off-by: NAndres Salomon <dilinger@collabora.co.uk>
Tested-by: NLeigh Porter <leigh@leighporter.org>
Tested-by: NJens Rottmann <JRottmann@LiPPERTEmbedded.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Callers (acpi_memhotplug.c, dock.c and others) check for the return
value of acpi_bus_add() and assume a valid device was returned in
case zero was returned.

Thus return -ENODEV if no device was found in acpi_bus_scan and
propagate this through acpi_bus_add and acpi_bus_start.

Also remove a confusing comment in acpiphp_glue.c, acpi_bus_scan
will and cannot invoke if acpi_bus_add returns no valid device.
Signed-off-by: NThomas Renninger <trenn@suse.de>
Acked-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

We are missing these when building the pci_dev from scratch off
the Open Firmware device-tree
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The aer_inject module hangs in aer_inject() when checking the device's
error masks.  The hang is due to a recursive use of the aer_inject lock.
The aer_inject() routine grabs the lock while processing the error and then
calls pci_read_config_dword to read the masks. The pci_read_config_dword
routine is earlier overridden by pci_read_aer, which among other things,
grabs the aer_inject lock.

Fixed by moving the pci_read_config_dword calls to read the masks to before
the lock is taken.
Acked-by: NHuang Ying <ying.huang@intel.com>
Signed-off-by: NAndrew Patterson <andrew.patterson@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The Correcteable/Uncorrectable Error Mask Registers are used by PCIe AER
driver which will controls the reporting of individual errors to PCIe RC
via PCIe error messages.

If hardware masks special error reporting to RC, the aer_inject driver
should not inject aer error.
Acked-by: NAndi Kleen <ak@linux.intel.com>
Signed-off-by: NYouquan, Song <youquan.song@intel.com>
Acked-by: NYing, Huang <ying.huang@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

It turns out that some PCI devices require extra delays when changing
power state from D3 to D0 (and the other way around).  Although this
is against the PCI specification, we can handle it quite easily by
allowing drivers to define arbitrary D3 delays for devices known to
require extra time for switching power states.

Introduce additional field d3_delay in struct pci_dev and use it to
store the value of the device's D0->D3 delay, in miliseconds.  Make
the PCI PM core code use the per-device d3_delay unless
pci_pm_d3_delay is greater (in which case the latter is used).
[This also allows the driver to specify d3_delay shorter than the
 10 ms required by the PCI standard if the device is known to be able
 to handle that.]

Make the sky2 driver set d3_delay to 150 for devices handled by it.

Fixes http://bugzilla.kernel.org/show_bug.cgi?id=14730 which is a
listed regression from 2.6.30.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Commit e0cd5160 "PCI: derive nearby CPUs from device's instead of bus'
NUMA information" causes an null pointer dereference when reading from
the sysfs attributes local_cpu* on Intel machines with no ACPI NUMA
proximity info, since dev->numa_node gets set to -1 for all PCI devices,
which then gets passed to cpumask_of_node.

Add a check to prevent this.
Signed-off-by: NDavid John <davidjon@xenontk.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

If the BIOS does not export _OSC to allow OS take over the PCIe AER, the
pcie aer driver will not initialize the aer service. However, the
aer_inject driver does not check this scenario, which results in a kernel
oops when injecting an aer error into OS.  For example:

BUG: unable to handle kernel NULL pointer dereference at 0000000000000350
IP: [<ffffffff812e08f7>] _spin_lock_irqsave+0xc/0x23
PGD 155c41067 PUD 157fe0067 PMD 0
Oops: 0002 [#1] SMP
Pid: 5119, comm: aer-inject Not tainted 2.6.32-rc8-mce #2
RIP: 0010:[<ffffffff812e08f7>]  [<ffffffff812e08f7>] _spin_lock_irqsave+0xc/0x23
RSP: 0018:ffff880157f81e28  EFLAGS: 00010096
RAX: 0000000000000296 RBX: 0000000000000000 RCX: 0000000000000100
RDX: 0000000000010000 RSI: 0000000000000246 RDI: 0000000000000350
RBP: ffff880157f81e28 R08: 0000000000000004 R09: ffff880157f81dac
R10: ffff88015a666f60 R11: ffff88015a666f40 R12: ffff88015758cc00
R13: 0000000000000350 R14: 0000000000000000 R15: 0000000000000100
FS:  00007f4d4a66e6f0(0000) GS:ffff8800282e0000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 0000000000000350 CR3: 000000015661a000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process aer-inject (pid: 5119, threadinfo ffff880157f80000, task ffff8801585f4340)
Stack:
 ffff880157f81e78 ffffffff811b1615 ffff880157f81e78 ffffffff81222823
Call Trace:
 [<ffffffff811b1615>] aer_irq+0x38/0x117
 [<ffffffff81222823>] ? device_for_each_child+0x5f/0x6f
 [<ffffffffa00967bf>] aer_inject_write+0x409/0x45e [aer_inject]
 [<ffffffff810eb80e>] vfs_write+0xae/0x16a
 [<ffffffff810eb98e>] sys_write+0x47/0x6e
 [<ffffffff8100ba2b>] system_call_fastpath+0x16/0x1b
RIP  [<ffffffff812e08f7>] _spin_lock_irqsave+0xc/0x23
 RSP <ffff880157f81e28>
CR2: 0000000000000350

So check the _OSC before assuming that AER is available to the OS.
Signed-off-by: NYouquan, Song <youquan.song@intel.com>
Acked-by: NYing, Huang <ying.huang@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

No change in logic.

Before:
  drivers/pci/pcie/portdrv_core.c:
    total: 7 errors, 2 warnings, 508 lines checked
  drivers/pci/pcie/portdrv_pci.c:
    total: 4 errors, 2 warnings, 300 lines checked

After:
  drivers/pci/pcie/portdrv_core.c:
    total: 0 errors, 0 warnings, 506 lines checked
  drivers/pci/pcie/portdrv_pci.c:
    total: 0 errors, 0 warnings, 299 lines checked
Signed-off-by: NHidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Introduced by commit 5b889bf2 ("PCI: Fix build if quirks are not
enabled"), which made the pci_dev_reset_methods[] array static and
'const', but didn't then change the code to match, and use a const
pointer when moving it to quirks.c.

Trivially fixed by just adding the required 'const' to the iterator
variable.
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

After commit b9c3b266 ("PCI: support
device-specific reset methods") the kernel build is broken if
CONFIG_PCI_QUIRKS is unset.

Fix this by moving pci_dev_specific_reset() to drivers/pci/quirks.c and
providing an empty replacement for !CONFIG_PCI_QUIRKS builds.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Reported-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The cardbus code creates PCI devices without ever going through the
necessary fixup bits and pieces that normal PCI devices go through.

There's in fact a commented out call to pcibios_fixup_bus() in there,
it's commented because ... it doesn't work.

I could make pcibios_fixup_bus() do the right thing on powerpc easily
but I felt it cleaner instead to provide a specific hook pci_fixup_cardbus
for which a weak empty implementation is provided by the PCI core.

This fixes cardbus on powerbooks and probably all other PowerPC
platforms which was broken completely for ever on some platforms and
since 2.6.31 on others such as PowerBooks when we made the DMA ops
mandatory (since those are setup by the fixups).
Acked-by: NDominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Changing occurrences of variants of PCI-X and PCIe to the PCI-SIG
terms listed in the "Trademark and Logo Usage Guidelines".
http://www.pcisig.com/developers/procedures/logos/Trademark_and_Logo_Usage_Guidelines_updated_112206.pdf

Patch is limited to drivers/pci/ and changes concern non-comment parts or
anything that might be visible to the user.
Signed-off-by: NStefan Assmann <sassmann@redhat.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Changing occurrences of variants of PCI-X and PCIe to the PCI-SIG
terms listed in the "Trademark and Logo Usage Guidelines".
http://www.pcisig.com/developers/procedures/logos/Trademark_and_Logo_Usage_Guidelines_updated_112206.pdf

Patch is limited to drivers/pci/ and changes concern comments only.
Signed-off-by: NStefan Assmann <sassmann@redhat.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Handle device specific timeout and use FLR.
Signed-off-by: NYu Zhao <yu.zhao@intel.com>
Signed-off-by: NDexuan Cui <dexuan.cui@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Handle device specific reset requirements (i.e. vendor reg for reset
along with appropriate timeout).
Signed-off-by: NYu Zhao <yu.zhao@intel.com>
Signed-off-by: NDexuan Cui <dexuan.cui@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Add a new type of quirk for resetting devices at pci_dev_reset time.
This is necessary to handle device with nonstandard reset procedures,
especially useful for guest drivers.
Signed-off-by: NYu Zhao <yu.zhao@intel.com>
Signed-off-by: NDexuan Cui <dexuan.cui@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Prior to this patch, if pci_read_config_byte(dev, PCI_CACHE_LINE_SIZE, ...)
returns 0 for all dev, pci_cache_line_size ends up set to zero
(instead of pci_dfl_cache_line_size).

This patch ensures the pci_cache_line_size = pci_dfl_cache_line_size
setting in the above scenario.

This happens in case of a kvm-88 guest (where, consequently, the rtl8139
NIC failed to initialize).
Acked-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NCsaba Henk <csaba@gluster.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Having read the PM part of the PCIe 2.0 specification more carefully
I think that it was a mistake to restrict the wake-up enable
propagation to non-PCIe devices, because if we do not request
control of the root ports' PME registers via OSC, PCIe PME is
supposed to be handled by the platform, just like the non-PCIe PME.
Even if we do that, the wake-up propagation is done to allow the
devices to wake up the system from sleep states which involves the
platform anyway, so it won't hurt.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

commit eb3fa7cb said Intel IOMMU

    Intel IOMMU driver needs memory during DMA map calls to setup its
    internal page tables and for other data structures.  As we all know
    that these DMA map calls are mostly called in the interrupt context
    or with the spinlock held by the upper level drivers(network/storage
    drivers), so in order to avoid any memory allocation failure due to
    low memory issues, this patch makes memory allocation by temporarily
    setting PF_MEMALLOC flags for the current task before making memory
    allocation calls.

    We evaluated mempools as a backup when kmem_cache_alloc() fails
    and found that mempools are really not useful here because
     1) We don't know for sure how much to reserve in advance
     2) And mempools are not useful for GFP_ATOMIC case (as we call
        memory alloc functions with GFP_ATOMIC)

    (akpm: point 2 is wrong...)

The above description doesn't justify to waste system emergency memory
at all. Non MM subsystem must not use PF_MEMALLOC. Memory reclaim need
few memory, anyone must not prevent it. Otherwise the system cause
mysterious hang-up and/or OOM Killer invokation.

Plus, akpm already pointed out what we should do.

Then, this patch revert it.

Cc: Keshavamurthy Anil S <anil.s.keshavamurthy@intel.com>
Signed-off-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

We are seeing a bug when booting w/ iommu=pt with current upstream
(bisect blames 19943b0e "intel-iommu:
Unify hardware and software passthrough support).

The issue is specific to this loop during identity map initialization
of each device:

domain_context_mapping_one(si_domain, ..., CONTEXT_TT_PASS_THROUGH)
...
		/* Skip top levels of page tables for
		* iommu which has less agaw than default.
		*/
		for (agaw = domain->agaw; agaw != iommu->agaw; agaw--) {
			pgd = phys_to_virt(dma_pte_addr(pgd));
			if (!dma_pte_present(pgd)) {      <------ failing here
				spin_unlock_irqrestore(&iommu->lock, flags);
			return -ENOMEM;
		}

This box has 2 iommu's in it.  The catchall iommu has MGAW == 48, and
SAGAW == 4.  The other iommu has MGAW == 39, SAGAW == 2.

The device that's failing the above pgd test is the only device connected
to the non-catchall iommu, which has a smaller address width than the
domain default.  This test is not necessary since the context is in PT
mode and the ASR is ignored.

Thanks to Don Dutile for discovering and debugging this one.

Cc: stable@kernel.org
Signed-off-by: NChris Wright <chrisw@sous-sol.org>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

The hotplug notifier will call find_domain() to see if the device in
question has been assigned an IOMMU domain. However, this should never
be called for devices with a "dummy" domain, such as graphics devices
when intel_iommu=igfx_off is set and the corresponding IOMMU isn't even
initialised. If you do that, it'll oops as it dereferences the (-1)
pointer.

The notifier function should check iommu_no_mapping() for the
device before doing anything else.

Cc: stable@kernel.org
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Some HP BIOSes report an RMRR region (a region which needs a 1:1 mapping
in the IOMMU for a given device) which has an end address lower than its
start address. Detect that and warn, rather than triggering the
BUG() in dma_pte_clear_range().

Cc: stable@kernel.org
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

The BIOS errors where an IOMMU is reported either at zero or a bogus
address are causing problems even when the IOMMU is disabled -- because
interrupt remapping uses the same hardware. Ensure that the checks get
applied for the interrupt remapping initialisation too.

Cc: stable@kernel.org
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Many BIOSes will lie to us about the existence of an IOMMU, and claim
that there is one at an address which actually returns all 0xFF.

We need to detect this early, so that we know we don't have a viable
IOMMU and can set up swiotlb before it's too late.

Cc: stable@kernel.org
Signed-off-by: NChris Wright <chrisw@sous-sol.org>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Remove a stray space in pci_save_state().
Signed-off-by: NKleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Commit ae21ee65 "PCI: acs p2p upsteram
forwarding enabling" doesn't actually enable ACS.

Add a function to pci core to allow an IOMMU to request that ACS
be enabled.  The existing mechanism of using iommu_found() in the pci
core to know when ACS should be enabled doesn't actually work due to
initialization order;  iommu has only been detected not initialized.

Have Intel and AMD IOMMUs request ACS, and Xen does as well during early
init of dom0.

Cc: Allen Kay <allen.m.kay@intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: NChris Wright <chrisw@sous-sol.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

This problem happened when removing PCIe root port using PCI logical
hotplug operation.

The immediate cause of this problem is that the pointer to invalid
data structure is passed to pcie_update_aspm_capable() by
pcie_aspm_exit_link_state(). When pcie_aspm_exit_link_state() received
a pointer to root port link, it unconfigures the root port link and
frees its data structure at first. At this point, there are not links
to configure under the root port and the data structure for root port
link is already freed. So pcie_aspm_exit_link_state() must not call
pcie_update_aspm_capable() and pcie_config_aspm_path().

This patch fixes the problem by changing pcie_aspm_exit_link_state()
not to call pcie_update_aspm_capable() and pcie_config_aspm_path() if
the specified link is root port link.

------------[ cut here ]------------
kernel BUG at drivers/pci/pcie/aspm.c:606!
invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC
last sysfs file: /sys/devices/pci0000:40/0000:40:13.0/remove
CPU 1
Modules linked in: shpchp
Pid: 9345, comm: sysfsd Not tainted 2.6.32-rc5 #98 ProLiant DL785 G6
RIP: 0010:[<ffffffff811df69b>]  [<ffffffff811df69b>] pcie_update_aspm_capable+0x15/0xbe
RSP: 0018:ffff88082a2f5ca0  EFLAGS: 00010202
RAX: 0000000000000e77 RBX: ffff88182cc3e000 RCX: ffff88082a33d006
RDX: 0000000000000001 RSI: ffffffff811dff4a RDI: ffff88182cc3e000
RBP: ffff88082a2f5cc0 R08: ffff88182cc3e000 R09: 0000000000000000
R10: ffff88182fc00180 R11: ffff88182fc00198 R12: ffff88182cc3e000
R13: 0000000000000000 R14: ffff88182cc3e000 R15: ffff88082a2f5e20
FS:  00007f259a64b6f0(0000) GS:ffff880864600000(0000) knlGS:0000000000000000
CS:  0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 00007feb53f73da0 CR3: 000000102cc94000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process sysfsd (pid: 9345, threadinfo ffff88082a2f4000, task ffff88082a33cf00)
Stack:
 ffff88182cc3e000 ffff88182cc3e000 0000000000000000 ffff88082a33cf00
<0> ffff88082a2f5cf0 ffffffff811dff52 ffff88082a2f5cf0 ffff88082c525168
<0> ffff88402c9fd2f8 ffff88402c9fd2f8 ffff88082a2f5d20 ffffffff811d7db2
Call Trace:
 [<ffffffff811dff52>] pcie_aspm_exit_link_state+0xf5/0x11e
 [<ffffffff811d7db2>] pci_stop_bus_device+0x76/0x7e
 [<ffffffff811d7d67>] pci_stop_bus_device+0x2b/0x7e
 [<ffffffff811d7e4f>] pci_remove_bus_device+0x15/0xb9
 [<ffffffff811dcb8c>] remove_callback+0x29/0x3a
 [<ffffffff81135aeb>] sysfs_schedule_callback_work+0x15/0x6d
 [<ffffffff81072790>] worker_thread+0x19d/0x298
 [<ffffffff8107273b>] ? worker_thread+0x148/0x298
 [<ffffffff81135ad6>] ? sysfs_schedule_callback_work+0x0/0x6d
 [<ffffffff810765c0>] ? autoremove_wake_function+0x0/0x38
 [<ffffffff810725f3>] ? worker_thread+0x0/0x298
 [<ffffffff8107629e>] kthread+0x7d/0x85
 [<ffffffff8102eafa>] child_rip+0xa/0x20
 [<ffffffff8102e4bc>] ? restore_args+0x0/0x30
 [<ffffffff81076221>] ? kthread+0x0/0x85
 [<ffffffff8102eaf0>] ? child_rip+0x0/0x20
Code: 89 e5 8a 50 48 31 c0 c0 ea 03 83 e2 07 e8 b2 de fe ff c9 48 98 c3 55 48 89 e5 41 56 49 89 fe 41 55 41 54 53 48 83 7f 10 00 74 04 <0f> 0b eb fe 48 8b 05 da 7d 63 00 4c 8d 60 e8 4c 89 e1 eb 24 4c
RIP  [<ffffffff811df69b>] pcie_update_aspm_capable+0x15/0xbe
 RSP <ffff88082a2f5ca0>
---[ end trace 6ae0f65bdeab8555 ]---
Reported-by: NAlex Chiang <achiang@hp.com>
Tested-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The pci_cleanup_aer_correct_error_status() function has been
#if 0'd out since 2.6.25.  Time to remove the dead code.
Signed-off-by: NAndrew Patterson <andrew.patterson@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The current implementation of pci_cleanup_aer_uncorrect_error_status
only clears either fatal or non-fatal error status bits depending
on the state of the I/O channel. This implementation will then often
leave some bits set after PCI error recovery completes.  The uncleared bit
settings will then be falsely reported the next time an AER interrupt is
generated for that hierarchy. An easy way to illustrate this issue is to
use the aer-inject module to simultaneously inject both an uncorrectable
non-fatal and uncorrectable fatal error.  One of the errors will not be
cleared.

This patch resolves this issue by unconditionally clearing all bits in
the AER uncorrectable status register. All settings and corrective action
strategies are saved and determined before
pci_cleanup_aer_uncorrect_error_status is called, so this change should not
affect errory handling functionality.
Signed-off-by: NAndrew Patterson <andrew.patterson@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Remove unnecessary definitions from portdrv.h and use generic
definitions instead.
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Remove 'port_type' field in struct pcie_port_data(), because we can
get port type information from struct pci_dev. With this change, this
patch also does followings:

 - Remove struct pcie_port_data because it no longer has any field.
 - Remove portdrv private definitions about port type (PCIE_RC_PORT,
   PCIE_SW_UPSTREAM_PORT and PCIE_SW_DOWNSTREAM_PORT), and use generic
   definitions instead.
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>