3945 and 4965 share the functionality for setting RTS and CTS to
the tx_cmd. Unify these functions and move the common
functionality to core.
Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Instead of always allocate the max number of tx queue structure,
use dynamic allocation based on the number of queues in device
configuration. With these changes, device does not have to allocate more
memory than the h/w can support.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

iwl_power_initialize() initializes driver data (not device hardware), and does
not need to execute more than once (when the driver initializes).  Therefore, it
does not belong in iwl3945_apm_init(), which initializes hardware, and may run
more than once.

Move it to iwl3945_pci_probe(), where it will run only once.  This agrees
with similar placement in iwl-agn.c's iwl_pci_probe(), although placement
under "services" seemed more appropriate than under "mac80211".
Signed-off-by: NBen Cahill <ben.m.cahill@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

iwl3945_rfkill_poll() has been silently calling wiphy_rfkill_set_hw_state()
every 2 seconds, regardless of whether hardware RF KILL switch changed state.

Call wiphy_rfkill_set_hw_state() only when RFKILL switch changes.
Add IWL_DEBUG_RF_KILL log message and documentation.
Signed-off-by: NBen Cahill <ben.m.cahill@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Now that we're unconditionally using apm_ops.stop() to reset and power-down
the device in __iwl3945_down(), the apm_ops.reset() is redundant.  Removing
this call will also allow us to remove iwl3945_apm_reset().

Remove unneeded iwl_clear_bit(CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ) because
this bit will be set again very soon in iwl3945_hw_txq_ctx_stop() and other
following calls.
Signed-off-by: NBen Cahill <ben.m.cahill@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In some cases (e.g. when mac80211 calls iwl_mac_stop() for suspend or user
no longer wants device active), device has not been going into low power state
via __iwl_down().  apm_ops.reset() does not put device into low power state;
instead it resets the device, then puts it into a powered-up state ready to be
re-loaded with uCode and re-started.  This has needlessly warmed up user's
laptops and drained batteries.

With current architecture in which mac80211 controls device up/down (including
resetting device after firmware errors), there is no need for apm_ops.reset()
any more; apm_ops.reset() is basically a combination of apm_ops.stop() and
apm_ops.init().

Instead, __iwl_down() now unconditionally places the device into a low-power
state via apm_ops.stop(). Device may be re-started via __iwl_up() calling
apm_ops.init() as soon as it may be needed (e.g. quickly for firmware errors),
but in the meantime, device will stop wasting energy.

Note that, even in this low power state, if driver re-enables interrupts,
the device retains the ability to sense the hardware RF-KILL switch, and
(except for 3945) interrupt the host when it changes.
Signed-off-by: NBen Cahill <ben.m.cahill@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Need to free the dynamic allocated memory before ieee80211_free_hw();
once call ieee80211_free_hw(), should not reference to "priv" data
structure.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The iwlwifi drivers have LED blinking requirements that
mac80211 cannot fulfill due to the use of just a single
LED instead of different ones for TX, RX, radio etc.
Instead, the single LED blinks according to transfers
and is solid on the rest of the time. As such, having
LED class devices registered that mac80211 triggers are
connected to is pointless as we don't use the triggers
anyway.

Remove all the useless code and add hooks into the
driver itself. At the same time, make the LED code
abstracted so the core code that determines blink rate
etc. can be shared between 3945 and agn in iwlcore.

At the same time, the fact that we removed the use of
the mac80211 LED triggers means we can also remove the
IWLWIFI_LEDS Kconfig symbol since the LED support is
now self-contained.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In order to have an easier way to debug issues, create
trace events (using the ftrace framework) that will
allow us to follow exactly what the driver is doing
with the device.

The text format isn't all that useful, but the binary
format can also be obtained easily via debugfs and
then analysed on the fly or offline with debugging
tools.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Ever since Johannes' "iwlwifi: improve scan support" iwlwifi
no longer needs any of lib80211's functions or definitions.

This patch updates iwlwifi's Kconfig _selections_ and
removes all left lib80211.h inclusions from the source files.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Acked-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Instead of hardcode module parameter's permissions, use pre-defined.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When hardware or uCode problem occurs driver captures significant
information from device to enable debugging. The format of this information
is different between 3945 and 4965 and later devices, yet currently the
3945 uses the 4965 and later format. Fix this by adding a new library call
that is initialized to the correct formatting routine based on device.

This moves the iwlagn event and error log handling back to iwl-agn.c to
make it part of iwlagn module.

Also remove the 3945 sysfs file that triggers dump of event log - there is
already a debugfs file that can do it for all drivers.
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Replenishment of receive buffers is done in the tasklet handling
received frames as well as in a workqueue. When we are in the tasklet
we cannot sleep and thus attempt atomic skb allocations. It is generally
not a big problem if this fails since iwl_rx_allocate is always followed
by a call to iwl_rx_queue_restock which will queue the work to replenish
the buffers at a time when sleeping is allowed.

We thus add the __GFP_NOWARN to the skb allocation in iwl_rx_allocate to
reduce the noise if such an allocation fails while we still have enough
buffers. We do maintain the warning and the error message when we are low
on buffers to communicate to the user that there is a potential problem with
memory availability on system

This addresses issue reported upstream in thread "iwlagn: order 2 page
allocation failures" in
http://thread.gmane.org/gmane.linux.kernel.wireless.general/39187Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Acked-by: NMel Gorman <mel@csn.ul.ie>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

RX handling maintains a few lists that keep track of the RX buffers.
Buffers move from one list to the other as they are used, replenished, and
again made available for usage. In one such instance, when a buffer is used
it enters the "rx_used" list. When buffers are replenished an skb is
attached to the buffer and it is moved to the "rx_free" list. The problem
here is that the buffer is first removed from the "rx_used" list _before_ the
skb is allocated. Thus, if the skb allocation fails this buffer remains
removed from the "rx_used" list and is thus lost for future usage.

Fix this by first allocating the skb before trying to attach it to a list.
We add an additional check to not do this unnecessarily.
Reported-by: NRick Farrington <rickdic@hotmail.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

RX handling maintains a few lists that keep track of the RX buffers.
Buffers move from one list to the other as they are used, replenished, and
again made available for usage. In one such instance, when a buffer is used
it enters the "rx_used" list. When buffers are replenished an skb is
attached to the buffer and it is moved to the "rx_free" list. The problem
here is that the buffer is first removed from the "rx_used" list _before_ the
skb is allocated. Thus, if the skb allocation fails this buffer remains
removed from the "rx_used" list and is thus lost for future usage.

Fix this by first allocating the skb before trying to attach it to a list.
We add an additional check to not do this unnecessarily.
Reported-by: NRick Farrington <rickdic@hotmail.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Significant literature suggests users use debug flags 0x43fff - this causes
the debug flags to be set that causes information to be printed for every
received frame - including beacons. In the best case it fills up the logs,
at worst it slows driver down and causes failures due to timeouts.

In the RX handler, print debugging only if user requested RX debugging.
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Commit 1ccb84d87d04df3c76cd4352fe69786d8c7cf016 by Wey-Yi Guy
("iwlwifi: clean up unused NL80211_IFTYPE_MONITOR for Monitor mode")
broke injection of non-broadcast frames to unassociated stations
(causing a SYSASSERT for all such injected frames), due to injected
frames no longer automatically getting a broadcast station ID assigned.
This patch restores the old behavior, fixing the aforementioned
regression.

Also, consistently check for IEEE80211_TX_CTL_INJECTED instead of
iwl_is_monitor_mode in the TX path, as TX_CTL_INJECTED specifically
means that a given packet is coming from a monitor interface, while
iwl_is_monitor_mode only shows whether a monitor interface exists
on the device.
Signed-off-by: NGábor Stefanik <netrolller.3d@gmail.com>
Acked-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With EDCA and HCCA we have 16 potential tid values. This is accommodated by
mac80211, but iwlwifi only supports EDCA. With this implementation it is
thus possible for mac80211 to request a tid that will cause iwlwifi to read
outside array bounds. A similar problem exists if traffic is received in an
unsupported category.

We add error checking to catch these situations.
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Depending on required latency requested by pm_qos (via mac80211)
we can automatically adjust the sleep state. Also, mac80211 has
a user-visible dynamic sleep feature where we are supposed to
stay awake after sending/receiving frames to better receive
response frames to our packets, this can be integrated into the
sleep command.

Currently, and this patch doesn't change that yet, we default
to using sleep level 1 if PS is enabled. With a module parameter
to iwlcore, automatic adjustment to changing network latency
requirements can be enabled -- this isn't yet the default due
to requiring more testing.

The goal is to enable automatic adjustment and then go into the
deepest possible sleep state possible depending on the networking
latency requirements.

This patch does, however, enable IEEE80211_HW_SUPPORTS_DYNAMIC_PS
to avoid the double-timer (one in software and one in the device)
when transmitting -- the exact timeout may be ignored but that is
not of big concern.

Note also that we keep the hard-coded power indices around for
thermal throttling -- the specification of that calls for using
the specified power levels. Those can also be selected in debugfs
to allow easier testing of such parameters.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Break down the traffic type and counter for both Tx and Rx.
Enhance the tx_statistics and rx_statistics debugfs function and move
to /sys/kernel/debug/ieee80211/phy0/iwlagn/debug directory to help
better debugging both driver and uCode related problems.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The traffic buffer will only beallocated and used if either bit 23
(IWL_DX_TX) or bit 24 (IWL_DL_RX) of "debug" is set;
example: "debug=0x800000" - log tx data traffic
         "debug=0x1000000" - log rx data traffic
         "debug=0x1800000" - log both tx and rx traffic

The traffic log will store the beginning portion (64 bytes)  of the
latest 256 of tx and rx packets in the round-robbin buffer for
debugging,
user can examine the log through debugfs file.

How to display the current logged tx/rx traffic and txfifo and rxfifo
read/write point:
"cat traffic_log" in /sys/kernel/debug/ieee80211/phy0/iwlagn/debug
directory

By echo "0" to traffic_log file will empty the traffic log buffer and
reset both tx and rx taffic log index to 0.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Commit "iwlwifi: make debug level more user friendly" cleaned up the
debug level handling. In doing so it created a single global debug
level for all devices. Some setups do consits of more that one iwlwifi
device and in these setups there is a requirement that debug levels
should be unique per device.

We now re-introduce the per device debugging while maintaining the
cleanup effort of the previous patch.

The maintain the global debug level and now introduce a per-device debug
level that will be used if it (the per-device debug level) is set. The
per-device debug level can be controlled via the debug_level sysfs file
while the global debug level is controlled by the debug module parameter.
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Acked-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A regression was added through patch a4ed90d6:

"cfg80211: respect API on orig_flags on channel for beacon hint"

We did indeed respect _orig flags but the intention was not clearly
stated in the commit log. This patch fixes firmware issues picked
up by iwlwifi when we lift passive scan of beaconing restrictions
on channels its EEPROM has been configured to always enable.

By doing so though we also disallowed beacon hints on devices
registering their wiphy with custom world regulatory domains
enabled, this happens to be currently ath5k, ath9k and ar9170.
The passive scan and beacon restrictions on those devices would
never be lifted even if we did find a beacon and the hardware did
support such enhancements when world roaming.

Since Johannes indicates iwlwifi firmware cannot be changed to
allow beacon hinting we set up a flag now to specifically allow
drivers to disable beacon hints for devices which cannot use them.

We enable the flag on iwlwifi to disable beacon hints and by default
enable it for all other drivers. It should be noted beacon hints lift
passive scan flags and beacon restrictions when we receive a beacon from
an AP on any 5 GHz non-DFS channels, and channels 12-14 on the 2.4 GHz
band. We don't bother with channels 1-11 as those channels are allowed
world wide.

This should fix world roaming for ath5k, ath9k and ar9170, thereby
improving scan time when we receive the first beacon from any AP,
and also enabling beaconing operation (AP/IBSS/Mesh) on cards which
would otherwise not be allowed to do so. Drivers not using custom
regulatory stuff (wiphy_apply_custom_regulatory()) were not affected
by this as the orig_flags for the channels would have been cleared
upon wiphy registration.

I tested this with a world roaming ath5k card.

Cc: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Reviewed-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The current command sending in iwlwifi is a bit of a mess:
 1) there is a struct, iwl_cmd, that contains both driver
    and device data in a single packed structure -- this
    is very confusing
 2) the on-stack data and the command metadata share a
    structure by embedding the latter in the former, which
    is also rather confusing because it leads to weird
    unions and similarly odd constructs
 3) each txq always has enough space for 256 commands,
    even if only 32 end up being used

This patch fixes these things:
 1) rename iwl_cmd to iwl_device_cmd and keep track of
    command metadata and device command separately, in
    two arrays in each tx queue
 2) remove the 'meta' member from iwl_host_cmd and only
    put in the required members
 3) allocate the cmd/meta arrays separately instead of
    embedding them into the txq structure
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We need to provide a reasonable minimum that will result in a
working setup if used. Set minimum to be 10 to provide for
4 standard TX queues + 1 command queue + 2 (unused) HCCA queues +
4 HT queues (one per AC).

We allow the user to change the number of queues used via a module
parameter and use this minimum value to check if it is valid. Without
this patch a user can select a value for the number of queues that
will result in a failing setup.
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Reviewed-by: NTomas Winkler <tomas.winkler@intel.com>
Acked-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rfkill state changes are mostly available through debug messages.
These are significant enough to always make user aware of so
we turn them into warnings.

Also insert a missing newline in some rfkill related debug message.
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When a hardware error is detected we need to be clear about that
and not create impression that the microcode is able to deal
with it.
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* Deprecate the "debug50" module parameter used to obtain
  5000 series and up debugging. Replace it with "debug" module
  parameter to match with original driver and be consistent
  between them. The "debug50" module parameter can still be used,
  except that the module parameter is not writable in keeping
  with its previous state. We currently just mark it as "deprecated"
  and do not have it in the feature-removal-schedule. Some more
  cleanup of module parameters needs to be done and can then be
  entered together.

* Only make "debug" module parameters visible if the driver
  is compiled with CONFIG_IWLWIFI_DEBUG. This will eliminate
  a lot of confusion where users think they have set debug flags
  but yet cannot see any debug output.

* Make module parameters writable. This eliminates the need for the
  "debug_level" sysfs file, which can now also be deprecated and
  added to feature-removal-schedule. This file is in significant
  use though with many iwlwifi documents and text referring users
  to it. We can thus not take its removal lightly and keep it around.

With iwlcore shared between iwlagn and iwl3945 we really do not need
debug module parameters for each but can instead have one debug
module parameter for the iwlcore module. The same issue is here as
with the sysfs file - a lot of iwlwifi documentation and text (like
bug reports) rely on iwlagn and iwl3945 having this module parameter,
so changing this to a module parameter of iwlcore will have significant
impact and we do not do this for that reason.

One consequence of this patch is that if a user is running a system
with both 3945 and later hardware then the setting of the one module
parameter will affect the value of the other. The likelihood of this
seems low - and even if this setup is present it does not seem like an
issue for both modules to run with the same debug level.
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Adding new API version to account for change to ucode file format.  New
header includes the build number of the ucode.  This build number is the
SVN revision thus allowing for exact correlation to the code that
generated it.

The header adds the build number so that older ucode images can also be
enhanced to include the build in the future.

some cleanup in iwl_read_ucode needed to ensure old header not used and
reduce unnecessary references through pointer with the data is already
in heap variable.
Signed-off-by: NJay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* Rename maximum number of queue (TFD_QUEUE_MAX) to IWL39_NUM_QUEUES to
  be consistent with rest of iwlwifi.
* Remove unused defines.
* Fix loops that iterate over number of TX queues to stop when maximum is reached
  (currently it is maximum + 1).
* Remove queues_num module parameter as it is not used.
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This changes the power_level file to adhere to the "one value
per file" sysfs rule. The user will know which power level was
requested as it will be the number just written to this file. It
is thus not necessary to create a new sysfs file for this value.

In addition it fixes a problem where powertop's parsing expects
this value to be the first value in this file without any descriptions.
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch unifies setup_rxon_timing funcions
of AGN and 3945. HWs differ only in supported maximal
beacon interval. This is reflected in hw_paras.max_beacon_itrvl
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When userspace requests only certain channels to be scanned,
we currently ignore that request entirely.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Patch fixes the following bugs at
http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=2005
http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=2007

If we suspend with an association and then resumed,
we need to synchronize the active rxon with staging rxon,
else we will get an error when iwl_alive_start try to commit
rxon and staging is set to channel 0. Before going to suspend
staging and active rxon are in sync. After resuming from the
suspend, iwl_mac_start is called and it clears the staging
rxon. Patch fixes the bug by not clearing the staging rxon
in iwl_mac_start.

Patch also adds similar fix to 3945.
Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This ports the iwlwifi rfkill code to the new API offered by
cfg80211 and thus removes a lot of useless stuff. The soft-
rfkill is completely removed since that is now handled by
setting the interfaces down.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Tested-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Port "iwlcore: Allow skb allocation from tasklet." to 3945

If RX queue becomes empty then we need to restock the queue from
tasklet to prevent ucode from starving. A caller to iwl_rx_allocate
will decide if allocated buffer should come from GFP_ATOMIC or
GFP_KERNEL.
Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch unifies 3945 and AGN station management
It also removes useless struct iwl_station_mgmt ops
and cleanups a bit the interface
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Tested-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Periodic RX interrupt needed with ICT interrupt to prevent RX race.
Sending RX interrupt require many steps to be done in the
the device:
 1- write interrupt to current index in ICT table.
 2- dma RX frame.
 3- update RX shared data to indicate last write index.
 4- send interrupt.
This could lead to RX race, driver could receive RX interrupt
but the shared data changes does not reflect that.
this could lead to RX race, RX periodic will solve this race
Signed-off-by: NMohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add ICT interrupt handler support, ICT should improve CPU utilization
 since it does not require target read which is very expensive. This
 interrupt handler only added to 5000 cards and newer. Device will write
 interrupts to ICT shared table to inform driver about its interrupts.

These patches will not touch 3945 and 4965 interrupt handlers and tasklet.
Signed-off-by: NMohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add new lock to be used when accessing some registers. Also move
    the register lock and iwl_grab_nic_access inside the function for register access. This
    will prevent from forgetting to hold locks and nic access in the right way and make code
    easier to maintain.

    We over use the priv->lock spin lock and I guess we need to add new
    one for Tx queue after that we might need to change most of these lock to
    BH and just keep priv->lock as irq type.
Signed-off-by: NMohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>