- 15 6月, 2018 9 次提交
-
-
由 Mel Gorman 提交于
Commit 5d190420 ("mremap: fix race between mremap() and page cleanning") fixed races between mremap and other operations for both file-backed and anonymous mappings. The file-backed was the most critical as it allowed the possibility that data could be changed on a physical page after page_mkclean returned which could trigger data loss or data integrity issues. A customer reported that the cost of the TLBs for anonymous regressions was excessive and resulting in a 30-50% drop in performance overall since this commit on a microbenchmark. Unfortunately I neither have access to the test-case nor can I describe what it does other than saying that mremap operations dominate heavily. This patch removes the LATENCY_LIMIT to handle TLB flushes on a PMD boundary instead of every 64 pages to reduce the number of TLB shootdowns by a factor of 8 in the ideal case. LATENCY_LIMIT was almost certainly used originally to limit the PTL hold times but the latency savings are likely offset by the cost of IPIs in many cases. This patch is not reported to completely restore performance but gets it within an acceptable percentage. The given metric here is simply described as "higher is better". Baseline that was known good 002: Metric: 91.05 004: Metric: 109.45 008: Metric: 73.08 016: Metric: 58.14 032: Metric: 61.09 064: Metric: 57.76 128: Metric: 55.43 Current 001: Metric: 54.98 002: Metric: 56.56 004: Metric: 41.22 008: Metric: 35.96 016: Metric: 36.45 032: Metric: 35.71 064: Metric: 35.73 128: Metric: 34.96 With patch 001: Metric: 61.43 002: Metric: 81.64 004: Metric: 67.92 008: Metric: 51.67 016: Metric: 50.47 032: Metric: 52.29 064: Metric: 50.01 128: Metric: 49.04 So for low threads, it's not restored but for larger number of threads, it's closer to the "known good" baseline. Using a different mremap-intensive workload that is not representative of the real workload there is little difference observed outside of noise in the headline metrics However, the TLB shootdowns are reduced by 11% on average and at the peak, TLB shootdowns were reduced by 21%. Interrupts were sampled every second while the workload ran to get those figures. It's known that the figures will vary as the non-representative load is non-deterministic. An alternative patch was posted that should have significantly reduced the TLB flushes but unfortunately it does not perform as well as this version on the customer test case. If revisited, the two patches can stack on top of each other. Link: http://lkml.kernel.org/r/20180606183803.k7qaw2xnbvzshv34@techsingularity.netSigned-off-by: NMel Gorman <mgorman@techsingularity.net> Reviewed-by: NAndrew Morton <akpm@linux-foundation.org> Cc: Nadav Amit <nadav.amit@gmail.com> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Aaron Lu <aaron.lu@intel.com> Cc: Hugh Dickins <hughd@google.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Mathieu Malaterre 提交于
Commit 26f09e9b ("mm/memblock: add memblock memory allocation apis") introduced two new function definitions: memblock_virt_alloc_try_nid_nopanic() memblock_virt_alloc_try_nid() Commit ea1f5f37 ("mm: define memblock_virt_alloc_try_nid_raw") introduced the following function definition: memblock_virt_alloc_try_nid_raw() This commit adds an includeof header file <linux/bootmem.h> to provide the missing function prototypes. Silence the following gcc warning (W=1): mm/memblock.c:1334:15: warning: no previous prototype for `memblock_virt_alloc_try_nid_raw' [-Wmissing-prototypes] mm/memblock.c:1371:15: warning: no previous prototype for `memblock_virt_alloc_try_nid_nopanic' [-Wmissing-prototypes] mm/memblock.c:1407:15: warning: no previous prototype for `memblock_virt_alloc_try_nid' [-Wmissing-prototypes] Link: http://lkml.kernel.org/r/20180606194144.16990-1-malat@debian.orgSigned-off-by: NMathieu Malaterre <malat@debian.org> Reviewed-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Tetsuo Handa 提交于
As a theoretical problem, dup_mmap() of an mm_struct with 60000+ vmas can loop while potentially allocating memory, with mm->mmap_sem held for write by current thread. This is bad if current thread was selected as an OOM victim, for current thread will continue allocations using memory reserves while OOM reaper is unable to reclaim memory. As an actually observable problem, it is not difficult to make OOM reaper unable to reclaim memory if the OOM victim is blocked at i_mmap_lock_write() in this loop. Unfortunately, since nobody can explain whether it is safe to use killable wait there, let's check for SIGKILL before trying to allocate memory. Even without an OOM event, there is no point with continuing the loop from the beginning if current thread is killed. I tested with debug printk(). This patch should be safe because we already fail if security_vm_enough_memory_mm() or kmem_cache_alloc(GFP_KERNEL) fails and exit_mmap() handles it. ***** Aborting dup_mmap() due to SIGKILL ***** ***** Aborting dup_mmap() due to SIGKILL ***** ***** Aborting dup_mmap() due to SIGKILL ***** ***** Aborting dup_mmap() due to SIGKILL ***** ***** Aborting exit_mmap() due to NULL mmap ***** [akpm@linux-foundation.org: add comment] Link: http://lkml.kernel.org/r/201804071938.CDE04681.SOFVQJFtMHOOLF@I-love.SAKURA.ne.jpSigned-off-by: NTetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Rik van Riel <riel@redhat.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: David Rientjes <rientjes@google.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Jarrett Farnitano 提交于
Without yielding while loading kimage segments, a large initrd will block all other work on the CPU performing the load until it is completed. For example loading an initrd of 200MB on a low power single core system will lock up the system for a few seconds. To increase system responsiveness to other tasks at that time, call cond_resched() in both the crash kernel and normal kernel segment loading loops. I did run into a practical problem. Hardware watchdogs on embedded systems can have short timers on the order of seconds. If the system is locked up for a few seconds with only a single core available, the watchdog may not be pet in a timely fashion. If this happens, the hardware watchdog will fire and reset the system. This really only becomes a problem when you are working with a single core, a decently sized initrd, and have a constrained hardware watchdog. Link: http://lkml.kernel.org/r/1528738546-3328-1-git-send-email-jmf@amazon.comSigned-off-by: NJarrett Farnitano <jmf@amazon.com> Reviewed-by: N"Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Shakeel Butt 提交于
The memcg kmem cache creation and deactivation (SLUB only) is asynchronous. If a root kmem cache is destroyed whose memcg cache is in the process of creation or deactivation, the kernel may crash. Example of one such crash: general protection fault: 0000 [#1] SMP PTI CPU: 1 PID: 1721 Comm: kworker/14:1 Not tainted 4.17.0-smp ... Workqueue: memcg_kmem_cache kmemcg_deactivate_workfn RIP: 0010:has_cpu_slab ... Call Trace: ? on_each_cpu_cond __kmem_cache_shrink kmemcg_cache_deact_after_rcu kmemcg_deactivate_workfn process_one_work worker_thread kthread ret_from_fork+0x35/0x40 To fix this race, on root kmem cache destruction, mark the cache as dying and flush the workqueue used for memcg kmem cache creation and deactivation. SLUB's memcg kmem cache deactivation also includes RCU callback and thus make sure all previous registered RCU callbacks have completed as well. [shakeelb@google.com: handle the RCU callbacks for SLUB deactivation] Link: http://lkml.kernel.org/r/20180611192951.195727-1-shakeelb@google.com [shakeelb@google.com: add more documentation, rename fields for readability] Link: http://lkml.kernel.org/r/20180522201336.196994-1-shakeelb@google.com [akpm@linux-foundation.org: fix build, per Shakeel] [shakeelb@google.com: v3. Instead of refcount, flush the workqueue] Link: http://lkml.kernel.org/r/20180530001204.183758-1-shakeelb@google.com Link: http://lkml.kernel.org/r/20180521174116.171846-1-shakeelb@google.comSigned-off-by: NShakeel Butt <shakeelb@google.com> Acked-by: NVladimir Davydov <vdavydov.dev@gmail.com> Cc: Michal Hocko <mhocko@kernel.org> Cc: Greg Thelen <gthelen@google.com> Cc: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: David Rientjes <rientjes@google.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Dan Williams 提交于
Hussam reports: I was poking around and for no real reason, I did cat /dev/mem and strings /dev/mem. Then I saw the following warning in dmesg. I saved it and rebooted immediately. memremap attempted on mixed range 0x000000000009c000 size: 0x1000 ------------[ cut here ]------------ WARNING: CPU: 0 PID: 11810 at kernel/memremap.c:98 memremap+0x104/0x170 [..] Call Trace: xlate_dev_mem_ptr+0x25/0x40 read_mem+0x89/0x1a0 __vfs_read+0x36/0x170 The memremap() implementation checks for attempts to remap System RAM with MEMREMAP_WB and instead redirects those mapping attempts to the linear map. However, that only works if the physical address range being remapped is page aligned. In low memory we have situations like the following: 00000000-00000fff : Reserved 00001000-0009fbff : System RAM 0009fc00-0009ffff : Reserved ...where System RAM intersects Reserved ranges on a sub-page page granularity. Given that devmem_is_allowed() special cases any attempt to map System RAM in the first 1MB of memory, replace page_is_ram() with the more precise region_intersects() to trap attempts to map disallowed ranges. Link: https://bugzilla.kernel.org/show_bug.cgi?id=199999 Link: http://lkml.kernel.org/r/152856436164.18127.2847888121707136898.stgit@dwillia2-desk3.amr.corp.intel.com Fixes: 92281dee ("arch: introduce memremap()") Signed-off-by: NDan Williams <dan.j.williams@intel.com> Reported-by: NHussam Al-Tayeb <me@hussam.eu.org> Tested-by: NHussam Al-Tayeb <me@hussam.eu.org> Cc: Christoph Hellwig <hch@lst.de> Cc: <stable@vger.kernel.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Daniel Jordan 提交于
Commit 570a335b ("swap_info: swap count continuations") introduces COUNT_CONTINUED but refers to it incorrectly as SWAP_HAS_CONT in a comment in swap_count. Fix it. Link: http://lkml.kernel.org/r/20180612175919.30413-1-daniel.m.jordan@oracle.com Fixes: 570a335b ("swap_info: swap count continuations") Signed-off-by: NDaniel Jordan <daniel.m.jordan@oracle.com> Reviewed-by: NAndrew Morton <akpm@linux-foundation.org> Cc: "Huang, Ying" <ying.huang@intel.com> Cc: Hugh Dickins <hughd@google.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Roman Gushchin 提交于
Shakeel reported a crash in mem_cgroup_protected(), which can be triggered by memcg reclaim if the legacy cgroup v1 use_hierarchy=0 mode is used: BUG: unable to handle kernel NULL pointer dereference at 0000000000000120 PGD 8000001ff55da067 P4D 8000001ff55da067 PUD 1fdc7df067 PMD 0 Oops: 0000 [#4] SMP PTI CPU: 0 PID: 15581 Comm: bash Tainted: G D 4.17.0-smp-clean #5 Hardware name: ... RIP: 0010:mem_cgroup_protected+0x54/0x130 Code: 4c 8b 8e 00 01 00 00 4c 8b 86 08 01 00 00 48 8d 8a 08 ff ff ff 48 85 d2 ba 00 00 00 00 48 0f 44 ca 48 39 c8 0f 84 cf 00 00 00 <48> 8b 81 20 01 00 00 4d 89 ca 4c 39 c8 4c 0f 46 d0 4d 85 d2 74 05 RSP: 0000:ffffabe64dfafa58 EFLAGS: 00010286 RAX: ffff9fb6ff03d000 RBX: ffff9fb6f5b1b000 RCX: 0000000000000000 RDX: 0000000000000000 RSI: ffff9fb6f5b1b000 RDI: ffff9fb6f5b1b000 RBP: ffffabe64dfafb08 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 000000000000c800 R12: ffffabe64dfafb88 R13: ffff9fb6f5b1b000 R14: ffffabe64dfafb88 R15: ffff9fb77fffe000 FS: 00007fed1f8ac700(0000) GS:ffff9fb6ff400000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000120 CR3: 0000001fdcf86003 CR4: 00000000001606f0 Call Trace: ? shrink_node+0x194/0x510 do_try_to_free_pages+0xfd/0x390 try_to_free_mem_cgroup_pages+0x123/0x210 try_charge+0x19e/0x700 mem_cgroup_try_charge+0x10b/0x1a0 wp_page_copy+0x134/0x5b0 do_wp_page+0x90/0x460 __handle_mm_fault+0x8e3/0xf30 handle_mm_fault+0xfe/0x220 __do_page_fault+0x262/0x500 do_page_fault+0x28/0xd0 ? page_fault+0x8/0x30 page_fault+0x1e/0x30 RIP: 0033:0x485b72 The problem happens because parent_mem_cgroup() returns a NULL pointer, which is dereferenced later without a check. As cgroup v1 has no memory guarantee support, let's make mem_cgroup_protected() immediately return MEMCG_PROT_NONE, if the given cgroup has no parent (non-hierarchical mode is used). Link: http://lkml.kernel.org/r/20180611175418.7007-2-guro@fb.com Fixes: bf8d5d52 ("memcg: introduce memory.min") Signed-off-by: NRoman Gushchin <guro@fb.com> Reported-by: NShakeel Butt <shakeelb@google.com> Tested-by: NShakeel Butt <shakeelb@google.com> Tested-by: NJohn Stultz <john.stultz@linaro.org> Acked-by: NJohannes Weiner <hannes@cmpxchg.org> Acked-by: NMichal Hocko <mhocko@kernel.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Jia He 提交于
In our armv8a server(QDF2400), I noticed lots of WARN_ON caused by PAGE_SIZE unaligned for rmap_item->address under memory pressure tests(start 20 guests and run memhog in the host). WARNING: CPU: 4 PID: 4641 at virt/kvm/arm/mmu.c:1826 kvm_age_hva_handler+0xc0/0xc8 CPU: 4 PID: 4641 Comm: memhog Tainted: G W 4.17.0-rc3+ #8 Call trace: kvm_age_hva_handler+0xc0/0xc8 handle_hva_to_gpa+0xa8/0xe0 kvm_age_hva+0x4c/0xe8 kvm_mmu_notifier_clear_flush_young+0x54/0x98 __mmu_notifier_clear_flush_young+0x6c/0xa0 page_referenced_one+0x154/0x1d8 rmap_walk_ksm+0x12c/0x1d0 rmap_walk+0x94/0xa0 page_referenced+0x194/0x1b0 shrink_page_list+0x674/0xc28 shrink_inactive_list+0x26c/0x5b8 shrink_node_memcg+0x35c/0x620 shrink_node+0x100/0x430 do_try_to_free_pages+0xe0/0x3a8 try_to_free_pages+0xe4/0x230 __alloc_pages_nodemask+0x564/0xdc0 alloc_pages_vma+0x90/0x228 do_anonymous_page+0xc8/0x4d0 __handle_mm_fault+0x4a0/0x508 handle_mm_fault+0xf8/0x1b0 do_page_fault+0x218/0x4b8 do_translation_fault+0x90/0xa0 do_mem_abort+0x68/0xf0 el0_da+0x24/0x28 In rmap_walk_ksm, the rmap_item->address might still have the STABLE_FLAG, then the start and end in handle_hva_to_gpa might not be PAGE_SIZE aligned. Thus it will cause exceptions in handle_hva_to_gpa on arm64. This patch fixes it by ignoring (not removing) the low bits of address when doing rmap_walk_ksm. IMO, it should be backported to stable tree. the storm of WARN_ONs is very easy for me to reproduce. More than that, I watched a panic (not reproducible) as follows: page:ffff7fe003742d80 count:-4871 mapcount:-2126053375 mapping: (null) index:0x0 flags: 0x1fffc00000000000() raw: 1fffc00000000000 0000000000000000 0000000000000000 ffffecf981470000 raw: dead000000000100 dead000000000200 ffff8017c001c000 0000000000000000 page dumped because: nonzero _refcount CPU: 29 PID: 18323 Comm: qemu-kvm Tainted: G W 4.14.15-5.hxt.aarch64 #1 Hardware name: <snip for confidential issues> Call trace: dump_backtrace+0x0/0x22c show_stack+0x24/0x2c dump_stack+0x8c/0xb0 bad_page+0xf4/0x154 free_pages_check_bad+0x90/0x9c free_pcppages_bulk+0x464/0x518 free_hot_cold_page+0x22c/0x300 __put_page+0x54/0x60 unmap_stage2_range+0x170/0x2b4 kvm_unmap_hva_handler+0x30/0x40 handle_hva_to_gpa+0xb0/0xec kvm_unmap_hva_range+0x5c/0xd0 I even injected a fault on purpose in kvm_unmap_hva_range by seting size=size-0x200, the call trace is similar as above. So I thought the panic is similarly caused by the root cause of WARN_ON. Andrea said: : It looks a straightforward safe fix, on x86 hva_to_gfn_memslot would : zap those bits and hide the misalignment caused by the low metadata : bits being erroneously left set in the address, but the arm code : notices when that's the last page in the memslot and the hva_end is : getting aligned and the size is below one page. : : I think the problem triggers in the addr += PAGE_SIZE of : unmap_stage2_ptes that never matches end because end is aligned but : addr is not. : : } while (pte++, addr += PAGE_SIZE, addr != end); : : x86 again only works on hva_start/hva_end after converting it to : gfn_start/end and that being in pfn units the bits are zapped before : they risk to cause trouble. Jia He said: : I've tested by myself in arm64 server (QDF2400,46 cpus,96G mem) Without : this patch, the WARN_ON is very easy for reproducing. After this patch, I : have run the same benchmarch for a whole day without any WARN_ONs Link: http://lkml.kernel.org/r/1525403506-6750-1-git-send-email-hejianet@gmail.comSigned-off-by: NJia He <jia.he@hxt-semitech.com> Reviewed-by: NAndrea Arcangeli <aarcange@redhat.com> Tested-by: NJia He <hejianet@gmail.com> Cc: Suzuki K Poulose <Suzuki.Poulose@arm.com> Cc: Minchan Kim <minchan@kernel.org> Cc: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com> Cc: Arvind Yadav <arvind.yadav.cs@gmail.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: <stable@vger.kernel.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 14 6月, 2018 6 次提交
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi由 Linus Torvalds 提交于
Pull SCSI fixes from James Bottomley: "This is a set of minor (and safe changes) that didn't make the initial pull request plus some bug fixes" * tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: scsi: qla2xxx: Mask off Scope bits in retry delay scsi: qla2xxx: Fix crash on qla2x00_mailbox_command scsi: aic7xxx: aic79xx: fix potential null pointer dereference on ahd scsi: mpt3sas: Add an I/O barrier scsi: qla2xxx: Fix setting lower transfer speed if GPSC fails scsi: hpsa: disable device during shutdown scsi: sd_zbc: Fix sd_zbc_check_zone_size() error path scsi: aacraid: remove bogus GFP_DMA32 specifies
-
git://git.infradead.org/linux-platform-drivers-x86由 Linus Torvalds 提交于
Pull x86 platform driver updates from Darren Hart: "Several incremental improvements including new keycodes, new models, new quirks, and related documentation. Adds LED platform driver activation for Mellanox systems. Some minor optimizations and cleanups. Includes several bug fixes, message silencing, mostly minor Automated summary: acer-wmi: - add another KEY_POWER keycode apple-gmux: - fix gmux_get_client_id()'s return type asus-laptop: - Simplify getting .drvdata asus-wireless: - Fix format specifier dell-laptop: - Fix keyboard backlight timeout on XPS 13 9370 dell-smbios: - Match on www.dell.com in OEM strings too dell-wmi: - Ignore new rfkill and fn-lock events - Set correct keycode for Fn + left arrow fujitsu-laptop: - Simplify soft key handling ideapad-laptop: - Add E42-80 to no_hw_rfkill - Add fn-lock setting - Add MIIX 720-12IKB to no_hw_rfkill lib/string_helpers: - Add missed declaration of struct task_struct intel_scu_ipc: - Replace mdelay with usleep_range in intel_scu_ipc_i2c_cntrl mlx-platform: - Add LED platform driver activation platform/mellanox: - Add new ODM system types to mlx-platform - mlxreg-hotplug: add extra cycle for hotplug work queue - mlxreg-hotplug: Document fixes for hotplug private data platform_data/mlxreg: - Document fixes for hotplug device silead_dmi: - Add entry for Chuwi Hi8 tablet touchscreen - Add touchscreen info for the Onda V891w tablet - Add info for the PoV mobii TAB-P800W (v2.0) - Add touchscreen info for the Jumper EZpad 6 Pro thinkpad_acpi: - silence false-positive-prone pr_warn - do not report thermal sensor state for tablet mode switch - silence HKEY 0x6032, 0x60f0, 0x6030" * tag 'platform-drivers-x86-v4.18-1' of git://git.infradead.org/linux-platform-drivers-x86: (30 commits) platform/x86: silead_dmi: Add entry for Chuwi Hi8 tablet touchscreen platform/x86: dell-laptop: Fix keyboard backlight timeout on XPS 13 9370 platform/x86: dell-wmi: Ignore new rfkill and fn-lock events platform/x86: mlx-platform: Add LED platform driver activation platform/mellanox: Add new ODM system types to mlx-platform platform/mellanox: mlxreg-hotplug: add extra cycle for hotplug work queue platform/x86: ideapad-laptop: Add E42-80 to no_hw_rfkill platform/x86: silead_dmi: Add touchscreen info for the Onda V891w tablet platform/x86: silead_dmi: Add info for the PoV mobii TAB-P800W (v2.0) platform/x86: silead_dmi: Add touchscreen info for the Jumper EZpad 6 Pro platform/x86: asus-wireless: Fix format specifier platform/x86: asus-wmi: Fix NULL pointer dereference platform/x86: dell-wmi: Set correct keycode for Fn + left arrow platform/x86: acer-wmi: add another KEY_POWER keycode platform/x86: ideapad-laptop: Add fn-lock setting platform/x86: ideapad-laptop: Add MIIX 720-12IKB to no_hw_rfkill lib/string_helpers: Add missed declaration of struct task_struct platform/x86: DELL_WMI use depends on instead of select for DELL_SMBIOS platform/mellanox: mlxreg-hotplug: Document fixes for hotplug private data platform_data/mlxreg: Document fixes for hotplug device ...
-
由 Linus Torvalds 提交于
Merge tag 'pwm/for-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm Pull pwm updates from Thierry Reding: "This contains a couple of fixes and cleanups for the Meson and ACPI/LPSS drivers as well as capture support for STM32. Note that given the cross- subsystem changes, the STM32 patches were merged through the MFD and PWM trees, both sharing an immutable branch" * tag 'pwm/for-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: pwm: stm32: Fix build warning with CONFIG_DMA_ENGINE disabled pwm: stm32: Enforce dependency on CONFIG_MFD_STM32_TIMERS ACPI / LPSS: Add missing prv_offset setting for byt/cht PWM devices pwm: lpss: platform: Save/restore the ctrl register over a suspend/resume dt-bindings: mfd: stm32-timers: Add support for dmas pwm: simplify getting .drvdata pwm: meson: Fix allocation of PWM channel array
-
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux由 Linus Torvalds 提交于
Pull i2c updates from Wolfram Sang: - mainly feature additions to drivers (stm32f7, qup, xlp9xx, mlxcpld, ...) - conversion to use the i2c_8bit_addr_from_msg macro consistently - move includes to platform_data - core updates to allow the (still in review) I3C subsystem to connect - and the regular share of smaller driver updates * 'i2c/for-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (68 commits) i2c: qup: fix building without CONFIG_ACPI i2c: tegra: Remove suspend-resume i2c: imx-lpi2c: Switch to SPDX identifier i2c: mxs: Switch to SPDX identifier i2c: busses: make use of i2c_8bit_addr_from_msg i2c: algos: make use of i2c_8bit_addr_from_msg i2c: rcar: document R8A77980 bindings i2c: qup: Add command-line parameter to override SCL frequency i2c: qup: Correct duty cycle for FM and FM+ i2c: qup: Add support for Fast Mode Plus i2c: qup: add probe path for Centriq ACPI devices i2c: robotfuzz-osif: drop pointless test i2c: robotfuzz-osif: remove pointless local variable i2c: rk3x: Don't print visible virtual mapping MMIO address i2c: opal: don't check number of messages in the driver i2c: ibm_iic: don't check number of messages in the driver i2c: imx: Switch to SPDX identifier i2c: mux: pca954x: merge calls to of_match_device and of_device_get_match_data i2c: mux: demux-pinctrl: use proper parent device for demux adapter i2c: mux: improve error message for failed symlink ...
-
由 Linus Torvalds 提交于
Merge tag 'apparmor-pr-2018-06-13' of git://git.kernel.org/pub/scm/linux/kernel/git/jj/linux-apparmor Pull AppArmor updates from John Johansen: "Features - add support for mapping secids and using secctxes - add the ability to get a task's secid - add support for audit rule filtering Cleanups: - multiple typo fixes - Convert to use match_string() helper - update git and wiki locations in AppArmor docs - improve get_buffers macro by using get_cpu_ptr - Use an IDR to allocate apparmor secids Bug fixes: - fix '*seclen' is never less than zero - fix mediation of prlimit - fix memory leak when deduping profile load - fix ptrace read check - fix memory leak of rule on error exit path" * tag 'apparmor-pr-2018-06-13' of git://git.kernel.org/pub/scm/linux/kernel/git/jj/linux-apparmor: (21 commits) apparmor: fix ptrace read check apparmor: fix memory leak when deduping profile load apparmor: fix mediation of prlimit apparmor: fixup secid map conversion to using IDR apparmor: Use an IDR to allocate apparmor secids apparmor: Fix memory leak of rule on error exit path apparmor: modify audit rule support to support profile stacks apparmor: Add support for audit rule filtering apparmor: update git and wiki locations in AppArmor docs apparmor: Convert to use match_string() helper apparmor: improve get_buffers macro by using get_cpu_ptr apparmor: fix '*seclen' is never less than zero apparmor: fix typo "preconfinement" apparmor: fix typo "independent" apparmor: fix typo "traverse" apparmor: fix typo "type" apparmor: fix typo "replace" apparmor: fix typo "comparison" apparmor: fix typo "loosen" apparmor: add the ability to get a task's secid ...
-
由 Linus Torvalds 提交于
The changes to automatically test for working stack protector compiler support in the Kconfig files removed the special STACKPROTECTOR_AUTO option that picked the strongest stack protector that the compiler supported. That was all a nice cleanup - it makes no sense to have the AUTO case now that the Kconfig phase can just determine the compiler support directly. HOWEVER. It also meant that doing "make oldconfig" would now _disable_ the strong stackprotector if you had AUTO enabled, because in a legacy config file, the sane stack protector configuration would look like CONFIG_HAVE_CC_STACKPROTECTOR=y # CONFIG_CC_STACKPROTECTOR_NONE is not set # CONFIG_CC_STACKPROTECTOR_REGULAR is not set # CONFIG_CC_STACKPROTECTOR_STRONG is not set CONFIG_CC_STACKPROTECTOR_AUTO=y and when you ran this through "make oldconfig" with the Kbuild changes, it would ask you about the regular CONFIG_CC_STACKPROTECTOR (that had been renamed from CONFIG_CC_STACKPROTECTOR_REGULAR to just CONFIG_CC_STACKPROTECTOR), but it would think that the STRONG version used to be disabled (because it was really enabled by AUTO), and would disable it in the new config, resulting in: CONFIG_HAVE_CC_STACKPROTECTOR=y CONFIG_CC_HAS_STACKPROTECTOR_NONE=y CONFIG_CC_STACKPROTECTOR=y # CONFIG_CC_STACKPROTECTOR_STRONG is not set CONFIG_CC_HAS_SANE_STACKPROTECTOR=y That's dangerously subtle - people could suddenly find themselves with the weaker stack protector setup without even realizing. The solution here is to just rename not just the old RECULAR stack protector option, but also the strong one. This does that by just removing the CC_ prefix entirely for the user choices, because it really is not about the compiler support (the compiler support now instead automatially impacts _visibility_ of the options to users). This results in "make oldconfig" actually asking the user for their choice, so that we don't have any silent subtle security model changes. The end result would generally look like this: CONFIG_HAVE_CC_STACKPROTECTOR=y CONFIG_CC_HAS_STACKPROTECTOR_NONE=y CONFIG_STACKPROTECTOR=y CONFIG_STACKPROTECTOR_STRONG=y CONFIG_CC_HAS_SANE_STACKPROTECTOR=y where the "CC_" versions really are about internal compiler infrastructure, not the user selections. Acked-by: NMasahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 13 6月, 2018 25 次提交
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild由 Linus Torvalds 提交于
Pull more Kbuild updates from Masahiro Yamada: - fix some bugs introduced by the recent Kconfig syntax extension - add some symbols about compiler information in Kconfig, such as CC_IS_GCC, CC_IS_CLANG, GCC_VERSION, etc. - test compiler capability for the stack protector in Kconfig, and clean-up Makefile - test compiler capability for GCC-plugins in Kconfig, and clean-up Makefile - allow to enable GCC-plugins for COMPILE_TEST - test compiler capability for KCOV in Kconfig and correct dependency - remove auto-detect mode of the GCOV format, which is now more nicely handled in Kconfig - test compiler capability for mprofile-kernel on PowerPC, and clean-up Makefile - misc cleanups * tag 'kbuild-v4.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: linux/linkage.h: replace VMLINUX_SYMBOL_STR() with __stringify() kconfig: fix localmodconfig sh: remove no-op macro VMLINUX_SYMBOL() powerpc/kbuild: move -mprofile-kernel check to Kconfig Documentation: kconfig: add recommended way to describe compiler support gcc-plugins: disable GCC_PLUGIN_STRUCTLEAK_BYREF_ALL for COMPILE_TEST gcc-plugins: allow to enable GCC_PLUGINS for COMPILE_TEST gcc-plugins: test plugin support in Kconfig and clean up Makefile gcc-plugins: move GCC version check for PowerPC to Kconfig kcov: test compiler capability in Kconfig and correct dependency gcov: remove CONFIG_GCOV_FORMAT_AUTODETECT arm64: move GCC version check for ARCH_SUPPORTS_INT128 to Kconfig kconfig: add CC_IS_CLANG and CLANG_VERSION kconfig: add CC_IS_GCC and GCC_VERSION stack-protector: test compiler capability in Kconfig and drop AUTO mode kbuild: fix endless syncconfig in case arch Makefile sets CROSS_COMPILE
-
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm由 Linus Torvalds 提交于
Pull additional ACPI updates from Rafael Wysocki: "These update the ACPICA code in the kernel to upstream revision 20180531 including one important AML parser fix and updates related to the IORT table, make the kernel recognize the "Windows 2017.2" _OSI string and update the customized methods documentation. Specifics: - Update the ACPICA code in the kernel to upstream revision 20180531 including: * AML parser fix to continue loading tables after detecting an AML error (Erik Schmauss). * AML parser debug option to dump parse trees (Bob Moore). * Debugger updates (Bob Moore). * Initial bits of Unload () operator deprecation (Bob Moore). * Updates related to the IORT table (Robin Murphy). - Make Linux respond to the "Windows 2017.2" _OSI string which allows native Thunderbolt enumeration to be used on Dell systems and was unsafe before recent changes in the PCI subsystem (Mario Limonciello) - Update the ACPI method customization feature documentation (Erik Schmauss)" * tag 'acpi-4.18-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: ACPICA: Recognize the _OSI string "Windows 2017.2" ACPICA: Update version to 20180531 ACPICA: Interpreter: Begin deprecation of Unload operator ACPICA: AML parser: attempt to continue loading table after error ACPICA: Debugger: Reduce verbosity for module-level code errors. ACPICA: AML Parser: Add debug option to dump parse trees ACPICA: Debugger: Add count of namespace nodes after namespace dump ACPICA: IORT: Add PMCG node supprt ACPICA: IORT: Update for revision D ACPI / Documentation: update ACPI customize method feature docs
-
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm由 Linus Torvalds 提交于
Pull more power management updates from Rafael Wysocki: "These revert a recent PM core change that introduced a regression, fix the build when the recently added Kryo cpufreq driver is selected, add support for devices attached to multiple power domains to the generic power domains (genpd) framework, add support for iowait boosting on systens with hardware-managed P-states (HWP) enabled to the intel_pstate driver, modify the behavior of the wakeup_count device attribute in sysfs, fix a few issues and clean up some ugliness, mostly in cpufreq (core and drivers) and in the cpupower utility. Specifics: - Revert a recent PM core change that attempted to fix an issue related to device links, but introduced a regression (Rafael Wysocki) - Fix build when the recently added cpufreq driver for Kryo processors is selected by making it possible to build that driver as a module (Arnd Bergmann) - Fix the long idle detection mechanism in the out-of-band (ondemand and conservative) cpufreq governors (Chen Yu) - Add support for devices in multiple power domains to the generic power domains (genpd) framework (Ulf Hansson) - Add support for iowait boosting on systems with hardware-managed P-states (HWP) enabled to the intel_pstate driver and make it use that feature on systems with Skylake Xeon processors as it is reported to improve performance significantly on those systems (Srinivas Pandruvada) - Fix and update the acpi_cpufreq, ti-cpufreq and imx6q cpufreq drivers (Colin Ian King, Suman Anna, Sébastien Szymanski) - Change the behavior of the wakeup_count device attribute in sysfs to expose the number of events when the device might have aborted system suspend in progress (Ravi Chandra Sadineni) - Fix two minor issues in the cpupower utility (Abhishek Goel, Colin Ian King)" * tag 'pm-4.18-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: Revert "PM / runtime: Fixup reference counting of device link suppliers at probe" cpufreq: imx6q: check speed grades for i.MX6ULL cpufreq: governors: Fix long idle detection logic in load calculation cpufreq: intel_pstate: enable boost for Skylake Xeon PM / wakeup: Export wakeup_count instead of event_count via sysfs PM / Domains: Add dev_pm_domain_attach_by_id() to manage multi PM domains PM / Domains: Add support for multi PM domains per device to genpd PM / Domains: Split genpd_dev_pm_attach() PM / Domains: Don't attach devices in genpd with multi PM domains PM / Domains: dt: Allow power-domain property to be a list of specifiers cpufreq: intel_pstate: New sysfs entry to control HWP boost cpufreq: intel_pstate: HWP boost performance on IO wakeup cpufreq: intel_pstate: Add HWP boost utility and sched util hooks cpufreq: ti-cpufreq: Use devres managed API in probe() cpufreq: ti-cpufreq: Fix an incorrect error return value cpufreq: ACPI: make function acpi_cpufreq_fast_switch() static cpufreq: kryo: allow building as a loadable module cpupower : Fix header name to read idle state name cpupower: fix spelling mistake: "logilename" -> "logfilename"
-
由 Rafael J. Wysocki 提交于
ACPICA update to upstream revision 20180531 (including an important AML parser fix and updates related to IORT) and a change to start responding to the "Windows 2017.2" _OSI string. * acpica: ACPICA: Recognize the _OSI string "Windows 2017.2" ACPICA: Update version to 20180531 ACPICA: Interpreter: Begin deprecation of Unload operator ACPICA: AML parser: attempt to continue loading table after error ACPICA: Debugger: Reduce verbosity for module-level code errors. ACPICA: AML Parser: Add debug option to dump parse trees ACPICA: Debugger: Add count of namespace nodes after namespace dump ACPICA: IORT: Add PMCG node supprt ACPICA: IORT: Update for revision D
-
由 Rafael J. Wysocki 提交于
Additional updates of the generic power domains (genpd) framework (support for devices attached to multiple domains) and the cpupower utility (minor fixes) for 4.18-rc1. * pm-domains: PM / Domains: Add dev_pm_domain_attach_by_id() to manage multi PM domains PM / Domains: Add support for multi PM domains per device to genpd PM / Domains: Split genpd_dev_pm_attach() PM / Domains: Don't attach devices in genpd with multi PM domains PM / Domains: dt: Allow power-domain property to be a list of specifiers * pm-tools: cpupower : Fix header name to read idle state name cpupower: fix spelling mistake: "logilename" -> "logfilename"
-
由 Rafael J. Wysocki 提交于
Additional cpufreq updates for 4.18-rc1: fixes and cleanups in the core and drivers and intel_pstate extension to do iowait boosting on systems with HWP that improves performance quite a bit. * pm-cpufreq: cpufreq: imx6q: check speed grades for i.MX6ULL cpufreq: governors: Fix long idle detection logic in load calculation cpufreq: intel_pstate: enable boost for Skylake Xeon cpufreq: intel_pstate: New sysfs entry to control HWP boost cpufreq: intel_pstate: HWP boost performance on IO wakeup cpufreq: intel_pstate: Add HWP boost utility and sched util hooks cpufreq: ti-cpufreq: Use devres managed API in probe() cpufreq: ti-cpufreq: Fix an incorrect error return value cpufreq: ACPI: make function acpi_cpufreq_fast_switch() static cpufreq: kryo: allow building as a loadable module
-
由 Linus Torvalds 提交于
This reverts commit 95cde3c5. The commit had good intentions, but it breaks kvm-tool and qemu-kvm. With it in place, "lkvm run" just fails with Error: KVM_CREATE_VM ioctl Warning: Failed init: kvm__init which isn't a wonderful error message, but bisection pinpointed the problematic commit. The problem is almost certainly due to the special kvm debugfs entries created dynamically by kvm under /sys/kernel/debug/kvm/. See kvm_create_vm_debugfs() Bisected-and-reported-by: NLinus Torvalds <torvalds@linux-foundation.org> Cc: Wanpeng Li <kernellwp@gmail.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Thomas Richter <tmricht@linux.ibm.com> Cc: Kees Cook <keescook@chromium.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Linus Torvalds 提交于
Commit ceef7d10 ("KVM: x86: VMX: hyper-v: Enlightened MSR-Bitmap support") broke the build with Hyper-V disabled, because it accesses ms_hyperv.nested_features without checking if that exists. This is the quick-and-hacky build fix. I suspect the proper fix is to replace the static_branch_unlikely(&enable_evmcs) tests with an inline helper function that also checks that CONFIG_HYPERV is enabled, since without that, enable_evmcs makes no sense. But I want a working build environment first and foremost, and I'm upset this slipped through in the first place. My primary build tests missed it because I tend to build with everything enabled, but it should have been caught in the kvm tree. Fixes: ceef7d10 ("KVM: x86: VMX: hyper-v: Enlightened MSR-Bitmap support") Cc: Vitaly Kuznetsov <vkuznets@redhat.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux由 Linus Torvalds 提交于
Pull more overflow updates from Kees Cook: "The rest of the overflow changes for v4.18-rc1. This includes the explicit overflow fixes from Silvio, further struct_size() conversions from Matthew, and a bug fix from Dan. But the bulk of it is the treewide conversions to use either the 2-factor argument allocators (e.g. kmalloc(a * b, ...) into kmalloc_array(a, b, ...) or the array_size() macros (e.g. vmalloc(a * b) into vmalloc(array_size(a, b)). Coccinelle was fighting me on several fronts, so I've done a bunch of manual whitespace updates in the patches as well. Summary: - Error path bug fix for overflow tests (Dan) - Additional struct_size() conversions (Matthew, Kees) - Explicitly reported overflow fixes (Silvio, Kees) - Add missing kvcalloc() function (Kees) - Treewide conversions of allocators to use either 2-factor argument variant when available, or array_size() and array3_size() as needed (Kees)" * tag 'overflow-v4.18-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (26 commits) treewide: Use array_size in f2fs_kvzalloc() treewide: Use array_size() in f2fs_kzalloc() treewide: Use array_size() in f2fs_kmalloc() treewide: Use array_size() in sock_kmalloc() treewide: Use array_size() in kvzalloc_node() treewide: Use array_size() in vzalloc_node() treewide: Use array_size() in vzalloc() treewide: Use array_size() in vmalloc() treewide: devm_kzalloc() -> devm_kcalloc() treewide: devm_kmalloc() -> devm_kmalloc_array() treewide: kvzalloc() -> kvcalloc() treewide: kvmalloc() -> kvmalloc_array() treewide: kzalloc_node() -> kcalloc_node() treewide: kzalloc() -> kcalloc() treewide: kmalloc() -> kmalloc_array() mm: Introduce kvcalloc() video: uvesafb: Fix integer overflow in allocation UBIFS: Fix potential integer overflow in allocation leds: Use struct_size() in allocation Convert intel uncore to struct_size ...
-
由 Linus Torvalds 提交于
Merge tag 'for-4.18/dm-changes-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm Pull device mapper updates from Mike Snitzer: - Adjust various DM structure members to improve alignment relative to 4.18 block's mempool_t and bioset changes. - Add DM writecache target that offers writeback caching to persistent memory or SSD. - Small DM core error message change to give context for why a DM table type transition wasn't allowed. * tag 'for-4.18/dm-changes-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm: dm: add writecache target dm: adjust structure members to improve alignment dm: report which conflicting type caused error during table_load()
-
由 Kees Cook 提交于
The f2fs_kvzalloc() function has no 2-factor argument form, so multiplication factors need to be wrapped in array_size(). This patch replaces cases of: f2fs_kvzalloc(handle, a * b, gfp) with: f2fs_kvzalloc(handle, array_size(a, b), gfp) as well as handling cases of: f2fs_kvzalloc(handle, a * b * c, gfp) with: f2fs_kvzalloc(handle, array3_size(a, b, c), gfp) This does, however, attempt to ignore constant size factors like: f2fs_kvzalloc(handle, 4 * 1024, gfp) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ expression HANDLE; type TYPE; expression THING, E; @@ ( f2fs_kvzalloc(HANDLE, - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | f2fs_kvzalloc(HANDLE, - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression HANDLE; expression COUNT; typedef u8; typedef __u8; @@ ( f2fs_kvzalloc(HANDLE, - sizeof(u8) * (COUNT) + COUNT , ...) | f2fs_kvzalloc(HANDLE, - sizeof(__u8) * (COUNT) + COUNT , ...) | f2fs_kvzalloc(HANDLE, - sizeof(char) * (COUNT) + COUNT , ...) | f2fs_kvzalloc(HANDLE, - sizeof(unsigned char) * (COUNT) + COUNT , ...) | f2fs_kvzalloc(HANDLE, - sizeof(u8) * COUNT + COUNT , ...) | f2fs_kvzalloc(HANDLE, - sizeof(__u8) * COUNT + COUNT , ...) | f2fs_kvzalloc(HANDLE, - sizeof(char) * COUNT + COUNT , ...) | f2fs_kvzalloc(HANDLE, - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ expression HANDLE; type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( f2fs_kvzalloc(HANDLE, - sizeof(TYPE) * (COUNT_ID) + array_size(COUNT_ID, sizeof(TYPE)) , ...) | f2fs_kvzalloc(HANDLE, - sizeof(TYPE) * COUNT_ID + array_size(COUNT_ID, sizeof(TYPE)) , ...) | f2fs_kvzalloc(HANDLE, - sizeof(TYPE) * (COUNT_CONST) + array_size(COUNT_CONST, sizeof(TYPE)) , ...) | f2fs_kvzalloc(HANDLE, - sizeof(TYPE) * COUNT_CONST + array_size(COUNT_CONST, sizeof(TYPE)) , ...) | f2fs_kvzalloc(HANDLE, - sizeof(THING) * (COUNT_ID) + array_size(COUNT_ID, sizeof(THING)) , ...) | f2fs_kvzalloc(HANDLE, - sizeof(THING) * COUNT_ID + array_size(COUNT_ID, sizeof(THING)) , ...) | f2fs_kvzalloc(HANDLE, - sizeof(THING) * (COUNT_CONST) + array_size(COUNT_CONST, sizeof(THING)) , ...) | f2fs_kvzalloc(HANDLE, - sizeof(THING) * COUNT_CONST + array_size(COUNT_CONST, sizeof(THING)) , ...) ) // 2-factor product, only identifiers. @@ expression HANDLE; identifier SIZE, COUNT; @@ f2fs_kvzalloc(HANDLE, - SIZE * COUNT + array_size(COUNT, SIZE) , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression HANDLE; expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( f2fs_kvzalloc(HANDLE, - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | f2fs_kvzalloc(HANDLE, - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | f2fs_kvzalloc(HANDLE, - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | f2fs_kvzalloc(HANDLE, - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | f2fs_kvzalloc(HANDLE, - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | f2fs_kvzalloc(HANDLE, - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | f2fs_kvzalloc(HANDLE, - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | f2fs_kvzalloc(HANDLE, - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression HANDLE; expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( f2fs_kvzalloc(HANDLE, - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | f2fs_kvzalloc(HANDLE, - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | f2fs_kvzalloc(HANDLE, - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | f2fs_kvzalloc(HANDLE, - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | f2fs_kvzalloc(HANDLE, - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | f2fs_kvzalloc(HANDLE, - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ expression HANDLE; identifier STRIDE, SIZE, COUNT; @@ ( f2fs_kvzalloc(HANDLE, - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | f2fs_kvzalloc(HANDLE, - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | f2fs_kvzalloc(HANDLE, - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | f2fs_kvzalloc(HANDLE, - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | f2fs_kvzalloc(HANDLE, - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | f2fs_kvzalloc(HANDLE, - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | f2fs_kvzalloc(HANDLE, - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | f2fs_kvzalloc(HANDLE, - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products // when they're not all constants... @@ expression HANDLE; expression E1, E2, E3; constant C1, C2, C3; @@ ( f2fs_kvzalloc(HANDLE, C1 * C2 * C3, ...) | f2fs_kvzalloc(HANDLE, - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants. @@ expression HANDLE; expression E1, E2; constant C1, C2; @@ ( f2fs_kvzalloc(HANDLE, C1 * C2, ...) | f2fs_kvzalloc(HANDLE, - E1 * E2 + array_size(E1, E2) , ...) ) Signed-off-by: NKees Cook <keescook@chromium.org>
-
由 Kees Cook 提交于
The f2fs_kzalloc() function has no 2-factor argument form, so multiplication factors need to be wrapped in array_size(). This patch replaces cases of: f2fs_kzalloc(handle, a * b, gfp) with: f2fs_kzalloc(handle, array_size(a, b), gfp) as well as handling cases of: f2fs_kzalloc(handle, a * b * c, gfp) with: f2fs_kzalloc(handle, array3_size(a, b, c), gfp) This does, however, attempt to ignore constant size factors like: f2fs_kzalloc(handle, 4 * 1024, gfp) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ expression HANDLE; type TYPE; expression THING, E; @@ ( f2fs_kzalloc(HANDLE, - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | f2fs_kzalloc(HANDLE, - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression HANDLE; expression COUNT; typedef u8; typedef __u8; @@ ( f2fs_kzalloc(HANDLE, - sizeof(u8) * (COUNT) + COUNT , ...) | f2fs_kzalloc(HANDLE, - sizeof(__u8) * (COUNT) + COUNT , ...) | f2fs_kzalloc(HANDLE, - sizeof(char) * (COUNT) + COUNT , ...) | f2fs_kzalloc(HANDLE, - sizeof(unsigned char) * (COUNT) + COUNT , ...) | f2fs_kzalloc(HANDLE, - sizeof(u8) * COUNT + COUNT , ...) | f2fs_kzalloc(HANDLE, - sizeof(__u8) * COUNT + COUNT , ...) | f2fs_kzalloc(HANDLE, - sizeof(char) * COUNT + COUNT , ...) | f2fs_kzalloc(HANDLE, - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ expression HANDLE; type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( f2fs_kzalloc(HANDLE, - sizeof(TYPE) * (COUNT_ID) + array_size(COUNT_ID, sizeof(TYPE)) , ...) | f2fs_kzalloc(HANDLE, - sizeof(TYPE) * COUNT_ID + array_size(COUNT_ID, sizeof(TYPE)) , ...) | f2fs_kzalloc(HANDLE, - sizeof(TYPE) * (COUNT_CONST) + array_size(COUNT_CONST, sizeof(TYPE)) , ...) | f2fs_kzalloc(HANDLE, - sizeof(TYPE) * COUNT_CONST + array_size(COUNT_CONST, sizeof(TYPE)) , ...) | f2fs_kzalloc(HANDLE, - sizeof(THING) * (COUNT_ID) + array_size(COUNT_ID, sizeof(THING)) , ...) | f2fs_kzalloc(HANDLE, - sizeof(THING) * COUNT_ID + array_size(COUNT_ID, sizeof(THING)) , ...) | f2fs_kzalloc(HANDLE, - sizeof(THING) * (COUNT_CONST) + array_size(COUNT_CONST, sizeof(THING)) , ...) | f2fs_kzalloc(HANDLE, - sizeof(THING) * COUNT_CONST + array_size(COUNT_CONST, sizeof(THING)) , ...) ) // 2-factor product, only identifiers. @@ expression HANDLE; identifier SIZE, COUNT; @@ f2fs_kzalloc(HANDLE, - SIZE * COUNT + array_size(COUNT, SIZE) , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression HANDLE; expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( f2fs_kzalloc(HANDLE, - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | f2fs_kzalloc(HANDLE, - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | f2fs_kzalloc(HANDLE, - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | f2fs_kzalloc(HANDLE, - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | f2fs_kzalloc(HANDLE, - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | f2fs_kzalloc(HANDLE, - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | f2fs_kzalloc(HANDLE, - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | f2fs_kzalloc(HANDLE, - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression HANDLE; expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( f2fs_kzalloc(HANDLE, - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | f2fs_kzalloc(HANDLE, - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | f2fs_kzalloc(HANDLE, - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | f2fs_kzalloc(HANDLE, - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | f2fs_kzalloc(HANDLE, - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | f2fs_kzalloc(HANDLE, - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ expression HANDLE; identifier STRIDE, SIZE, COUNT; @@ ( f2fs_kzalloc(HANDLE, - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | f2fs_kzalloc(HANDLE, - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | f2fs_kzalloc(HANDLE, - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | f2fs_kzalloc(HANDLE, - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | f2fs_kzalloc(HANDLE, - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | f2fs_kzalloc(HANDLE, - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | f2fs_kzalloc(HANDLE, - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | f2fs_kzalloc(HANDLE, - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products // when they're not all constants... @@ expression HANDLE; expression E1, E2, E3; constant C1, C2, C3; @@ ( f2fs_kzalloc(HANDLE, C1 * C2 * C3, ...) | f2fs_kzalloc(HANDLE, - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants. @@ expression HANDLE; expression E1, E2; constant C1, C2; @@ ( f2fs_kzalloc(HANDLE, C1 * C2, ...) | f2fs_kzalloc(HANDLE, - E1 * E2 + array_size(E1, E2) , ...) ) Signed-off-by: NKees Cook <keescook@chromium.org>
-
由 Kees Cook 提交于
The f2fs_kmalloc() function has no 2-factor argument form, so multiplication factors need to be wrapped in array_size(). This patch replaces cases of: f2fs_kmalloc(handle, a * b, gfp) with: f2fs_kmalloc(handle, array_size(a, b), gfp) as well as handling cases of: f2fs_kmalloc(handle, a * b * c, gfp) with: f2fs_kmalloc(handle, array3_size(a, b, c), gfp) This does, however, attempt to ignore constant size factors like: f2fs_kmalloc(handle, 4 * 1024, gfp) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ expression HANDLE; type TYPE; expression THING, E; @@ ( f2fs_kmalloc(HANDLE, - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | f2fs_kmalloc(HANDLE, - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression HANDLE; expression COUNT; typedef u8; typedef __u8; @@ ( f2fs_kmalloc(HANDLE, - sizeof(u8) * (COUNT) + COUNT , ...) | f2fs_kmalloc(HANDLE, - sizeof(__u8) * (COUNT) + COUNT , ...) | f2fs_kmalloc(HANDLE, - sizeof(char) * (COUNT) + COUNT , ...) | f2fs_kmalloc(HANDLE, - sizeof(unsigned char) * (COUNT) + COUNT , ...) | f2fs_kmalloc(HANDLE, - sizeof(u8) * COUNT + COUNT , ...) | f2fs_kmalloc(HANDLE, - sizeof(__u8) * COUNT + COUNT , ...) | f2fs_kmalloc(HANDLE, - sizeof(char) * COUNT + COUNT , ...) | f2fs_kmalloc(HANDLE, - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ expression HANDLE; type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( f2fs_kmalloc(HANDLE, - sizeof(TYPE) * (COUNT_ID) + array_size(COUNT_ID, sizeof(TYPE)) , ...) | f2fs_kmalloc(HANDLE, - sizeof(TYPE) * COUNT_ID + array_size(COUNT_ID, sizeof(TYPE)) , ...) | f2fs_kmalloc(HANDLE, - sizeof(TYPE) * (COUNT_CONST) + array_size(COUNT_CONST, sizeof(TYPE)) , ...) | f2fs_kmalloc(HANDLE, - sizeof(TYPE) * COUNT_CONST + array_size(COUNT_CONST, sizeof(TYPE)) , ...) | f2fs_kmalloc(HANDLE, - sizeof(THING) * (COUNT_ID) + array_size(COUNT_ID, sizeof(THING)) , ...) | f2fs_kmalloc(HANDLE, - sizeof(THING) * COUNT_ID + array_size(COUNT_ID, sizeof(THING)) , ...) | f2fs_kmalloc(HANDLE, - sizeof(THING) * (COUNT_CONST) + array_size(COUNT_CONST, sizeof(THING)) , ...) | f2fs_kmalloc(HANDLE, - sizeof(THING) * COUNT_CONST + array_size(COUNT_CONST, sizeof(THING)) , ...) ) // 2-factor product, only identifiers. @@ expression HANDLE; identifier SIZE, COUNT; @@ f2fs_kmalloc(HANDLE, - SIZE * COUNT + array_size(COUNT, SIZE) , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression HANDLE; expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( f2fs_kmalloc(HANDLE, - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | f2fs_kmalloc(HANDLE, - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | f2fs_kmalloc(HANDLE, - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | f2fs_kmalloc(HANDLE, - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | f2fs_kmalloc(HANDLE, - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | f2fs_kmalloc(HANDLE, - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | f2fs_kmalloc(HANDLE, - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | f2fs_kmalloc(HANDLE, - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression HANDLE; expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( f2fs_kmalloc(HANDLE, - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | f2fs_kmalloc(HANDLE, - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | f2fs_kmalloc(HANDLE, - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | f2fs_kmalloc(HANDLE, - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | f2fs_kmalloc(HANDLE, - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | f2fs_kmalloc(HANDLE, - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ expression HANDLE; identifier STRIDE, SIZE, COUNT; @@ ( f2fs_kmalloc(HANDLE, - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | f2fs_kmalloc(HANDLE, - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | f2fs_kmalloc(HANDLE, - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | f2fs_kmalloc(HANDLE, - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | f2fs_kmalloc(HANDLE, - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | f2fs_kmalloc(HANDLE, - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | f2fs_kmalloc(HANDLE, - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | f2fs_kmalloc(HANDLE, - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products // when they're not all constants... @@ expression HANDLE; expression E1, E2, E3; constant C1, C2, C3; @@ ( f2fs_kmalloc(HANDLE, C1 * C2 * C3, ...) | f2fs_kmalloc(HANDLE, - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants. @@ expression HANDLE; expression E1, E2; constant C1, C2; @@ ( f2fs_kmalloc(HANDLE, C1 * C2, ...) | f2fs_kmalloc(HANDLE, - E1 * E2 + array_size(E1, E2) , ...) ) Signed-off-by: NKees Cook <keescook@chromium.org>
-
由 Kees Cook 提交于
The sock_kmalloc() function has no 2-factor argument form, so multiplication factors need to be wrapped in array_size(). This patch replaces cases of: sock_kmalloc(handle, a * b, gfp) with: sock_kmalloc(handle, array_size(a, b), gfp) as well as handling cases of: sock_kmalloc(handle, a * b * c, gfp) with: sock_kmalloc(handle, array3_size(a, b, c), gfp) This does, however, attempt to ignore constant size factors like: sock_kmalloc(handle, 4 * 1024, gfp) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ expression HANDLE; type TYPE; expression THING, E; @@ ( sock_kmalloc(HANDLE, - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | sock_kmalloc(HANDLE, - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression HANDLE; expression COUNT; typedef u8; typedef __u8; @@ ( sock_kmalloc(HANDLE, - sizeof(u8) * (COUNT) + COUNT , ...) | sock_kmalloc(HANDLE, - sizeof(__u8) * (COUNT) + COUNT , ...) | sock_kmalloc(HANDLE, - sizeof(char) * (COUNT) + COUNT , ...) | sock_kmalloc(HANDLE, - sizeof(unsigned char) * (COUNT) + COUNT , ...) | sock_kmalloc(HANDLE, - sizeof(u8) * COUNT + COUNT , ...) | sock_kmalloc(HANDLE, - sizeof(__u8) * COUNT + COUNT , ...) | sock_kmalloc(HANDLE, - sizeof(char) * COUNT + COUNT , ...) | sock_kmalloc(HANDLE, - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ expression HANDLE; type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( sock_kmalloc(HANDLE, - sizeof(TYPE) * (COUNT_ID) + array_size(COUNT_ID, sizeof(TYPE)) , ...) | sock_kmalloc(HANDLE, - sizeof(TYPE) * COUNT_ID + array_size(COUNT_ID, sizeof(TYPE)) , ...) | sock_kmalloc(HANDLE, - sizeof(TYPE) * (COUNT_CONST) + array_size(COUNT_CONST, sizeof(TYPE)) , ...) | sock_kmalloc(HANDLE, - sizeof(TYPE) * COUNT_CONST + array_size(COUNT_CONST, sizeof(TYPE)) , ...) | sock_kmalloc(HANDLE, - sizeof(THING) * (COUNT_ID) + array_size(COUNT_ID, sizeof(THING)) , ...) | sock_kmalloc(HANDLE, - sizeof(THING) * COUNT_ID + array_size(COUNT_ID, sizeof(THING)) , ...) | sock_kmalloc(HANDLE, - sizeof(THING) * (COUNT_CONST) + array_size(COUNT_CONST, sizeof(THING)) , ...) | sock_kmalloc(HANDLE, - sizeof(THING) * COUNT_CONST + array_size(COUNT_CONST, sizeof(THING)) , ...) ) // 2-factor product, only identifiers. @@ expression HANDLE; identifier SIZE, COUNT; @@ sock_kmalloc(HANDLE, - SIZE * COUNT + array_size(COUNT, SIZE) , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression HANDLE; expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( sock_kmalloc(HANDLE, - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | sock_kmalloc(HANDLE, - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | sock_kmalloc(HANDLE, - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | sock_kmalloc(HANDLE, - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | sock_kmalloc(HANDLE, - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | sock_kmalloc(HANDLE, - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | sock_kmalloc(HANDLE, - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | sock_kmalloc(HANDLE, - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression HANDLE; expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( sock_kmalloc(HANDLE, - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | sock_kmalloc(HANDLE, - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | sock_kmalloc(HANDLE, - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | sock_kmalloc(HANDLE, - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | sock_kmalloc(HANDLE, - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | sock_kmalloc(HANDLE, - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ expression HANDLE; identifier STRIDE, SIZE, COUNT; @@ ( sock_kmalloc(HANDLE, - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | sock_kmalloc(HANDLE, - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | sock_kmalloc(HANDLE, - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | sock_kmalloc(HANDLE, - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | sock_kmalloc(HANDLE, - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | sock_kmalloc(HANDLE, - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | sock_kmalloc(HANDLE, - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | sock_kmalloc(HANDLE, - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products // when they're not all constants... @@ expression HANDLE; expression E1, E2, E3; constant C1, C2, C3; @@ ( sock_kmalloc(HANDLE, C1 * C2 * C3, ...) | sock_kmalloc(HANDLE, - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants. @@ expression HANDLE; expression E1, E2; constant C1, C2; @@ ( sock_kmalloc(HANDLE, C1 * C2, ...) | sock_kmalloc(HANDLE, - E1 * E2 + array_size(E1, E2) , ...) ) Signed-off-by: NKees Cook <keescook@chromium.org>
-
由 Kees Cook 提交于
The kvzalloc_node() function has no 2-factor argument form, so multiplication factors need to be wrapped in array_size(). This patch replaces cases of: kvzalloc_node(a * b, gfp, node) with: kvzalloc_node(array_size(a, b), gfp, node) as well as handling cases of: kvzalloc_node(a * b * c, gfp, node) with: kvzalloc_node(array3_size(a, b, c), gfp, node) This does, however, attempt to ignore constant size factors like: kvzalloc_node(4 * 1024, gfp, node) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ type TYPE; expression THING, E; @@ ( kvzalloc_node( - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | kvzalloc_node( - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression COUNT; typedef u8; typedef __u8; @@ ( kvzalloc_node( - sizeof(u8) * (COUNT) + COUNT , ...) | kvzalloc_node( - sizeof(__u8) * (COUNT) + COUNT , ...) | kvzalloc_node( - sizeof(char) * (COUNT) + COUNT , ...) | kvzalloc_node( - sizeof(unsigned char) * (COUNT) + COUNT , ...) | kvzalloc_node( - sizeof(u8) * COUNT + COUNT , ...) | kvzalloc_node( - sizeof(__u8) * COUNT + COUNT , ...) | kvzalloc_node( - sizeof(char) * COUNT + COUNT , ...) | kvzalloc_node( - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( kvzalloc_node( - sizeof(TYPE) * (COUNT_ID) + array_size(COUNT_ID, sizeof(TYPE)) , ...) | kvzalloc_node( - sizeof(TYPE) * COUNT_ID + array_size(COUNT_ID, sizeof(TYPE)) , ...) | kvzalloc_node( - sizeof(TYPE) * (COUNT_CONST) + array_size(COUNT_CONST, sizeof(TYPE)) , ...) | kvzalloc_node( - sizeof(TYPE) * COUNT_CONST + array_size(COUNT_CONST, sizeof(TYPE)) , ...) | kvzalloc_node( - sizeof(THING) * (COUNT_ID) + array_size(COUNT_ID, sizeof(THING)) , ...) | kvzalloc_node( - sizeof(THING) * COUNT_ID + array_size(COUNT_ID, sizeof(THING)) , ...) | kvzalloc_node( - sizeof(THING) * (COUNT_CONST) + array_size(COUNT_CONST, sizeof(THING)) , ...) | kvzalloc_node( - sizeof(THING) * COUNT_CONST + array_size(COUNT_CONST, sizeof(THING)) , ...) ) // 2-factor product, only identifiers. @@ identifier SIZE, COUNT; @@ kvzalloc_node( - SIZE * COUNT + array_size(COUNT, SIZE) , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( kvzalloc_node( - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kvzalloc_node( - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kvzalloc_node( - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kvzalloc_node( - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kvzalloc_node( - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kvzalloc_node( - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kvzalloc_node( - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kvzalloc_node( - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( kvzalloc_node( - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kvzalloc_node( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kvzalloc_node( - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kvzalloc_node( - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kvzalloc_node( - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | kvzalloc_node( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ identifier STRIDE, SIZE, COUNT; @@ ( kvzalloc_node( - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kvzalloc_node( - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kvzalloc_node( - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kvzalloc_node( - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kvzalloc_node( - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kvzalloc_node( - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kvzalloc_node( - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kvzalloc_node( - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products // when they're not all constants... @@ expression E1, E2, E3; constant C1, C2, C3; @@ ( kvzalloc_node(C1 * C2 * C3, ...) | kvzalloc_node( - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants. @@ expression E1, E2; constant C1, C2; @@ ( kvzalloc_node(C1 * C2, ...) | kvzalloc_node( - E1 * E2 + array_size(E1, E2) , ...) ) Signed-off-by: NKees Cook <keescook@chromium.org>
-
由 Kees Cook 提交于
The vzalloc_node() function has no 2-factor argument form, so multiplication factors need to be wrapped in array_size(). This patch replaces cases of: vzalloc_node(a * b, node) with: vzalloc_node(array_size(a, b), node) as well as handling cases of: vzalloc_node(a * b * c, node) with: vzalloc_node(array3_size(a, b, c), node) This does, however, attempt to ignore constant size factors like: vzalloc_node(4 * 1024, node) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ type TYPE; expression THING, E; @@ ( vzalloc_node( - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | vzalloc_node( - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression COUNT; typedef u8; typedef __u8; @@ ( vzalloc_node( - sizeof(u8) * (COUNT) + COUNT , ...) | vzalloc_node( - sizeof(__u8) * (COUNT) + COUNT , ...) | vzalloc_node( - sizeof(char) * (COUNT) + COUNT , ...) | vzalloc_node( - sizeof(unsigned char) * (COUNT) + COUNT , ...) | vzalloc_node( - sizeof(u8) * COUNT + COUNT , ...) | vzalloc_node( - sizeof(__u8) * COUNT + COUNT , ...) | vzalloc_node( - sizeof(char) * COUNT + COUNT , ...) | vzalloc_node( - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( vzalloc_node( - sizeof(TYPE) * (COUNT_ID) + array_size(COUNT_ID, sizeof(TYPE)) , ...) | vzalloc_node( - sizeof(TYPE) * COUNT_ID + array_size(COUNT_ID, sizeof(TYPE)) , ...) | vzalloc_node( - sizeof(TYPE) * (COUNT_CONST) + array_size(COUNT_CONST, sizeof(TYPE)) , ...) | vzalloc_node( - sizeof(TYPE) * COUNT_CONST + array_size(COUNT_CONST, sizeof(TYPE)) , ...) | vzalloc_node( - sizeof(THING) * (COUNT_ID) + array_size(COUNT_ID, sizeof(THING)) , ...) | vzalloc_node( - sizeof(THING) * COUNT_ID + array_size(COUNT_ID, sizeof(THING)) , ...) | vzalloc_node( - sizeof(THING) * (COUNT_CONST) + array_size(COUNT_CONST, sizeof(THING)) , ...) | vzalloc_node( - sizeof(THING) * COUNT_CONST + array_size(COUNT_CONST, sizeof(THING)) , ...) ) // 2-factor product, only identifiers. @@ identifier SIZE, COUNT; @@ vzalloc_node( - SIZE * COUNT + array_size(COUNT, SIZE) , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( vzalloc_node( - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | vzalloc_node( - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | vzalloc_node( - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | vzalloc_node( - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | vzalloc_node( - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | vzalloc_node( - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | vzalloc_node( - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | vzalloc_node( - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( vzalloc_node( - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | vzalloc_node( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | vzalloc_node( - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | vzalloc_node( - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | vzalloc_node( - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | vzalloc_node( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ identifier STRIDE, SIZE, COUNT; @@ ( vzalloc_node( - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | vzalloc_node( - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | vzalloc_node( - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | vzalloc_node( - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | vzalloc_node( - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | vzalloc_node( - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | vzalloc_node( - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | vzalloc_node( - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products // when they're not all constants... @@ expression E1, E2, E3; constant C1, C2, C3; @@ ( vzalloc_node(C1 * C2 * C3, ...) | vzalloc_node( - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants. @@ expression E1, E2; constant C1, C2; @@ ( vzalloc_node(C1 * C2, ...) | vzalloc_node( - E1 * E2 + array_size(E1, E2) , ...) ) Signed-off-by: NKees Cook <keescook@chromium.org>
-
由 Kees Cook 提交于
The vzalloc() function has no 2-factor argument form, so multiplication factors need to be wrapped in array_size(). This patch replaces cases of: vzalloc(a * b) with: vzalloc(array_size(a, b)) as well as handling cases of: vzalloc(a * b * c) with: vzalloc(array3_size(a, b, c)) This does, however, attempt to ignore constant size factors like: vzalloc(4 * 1024) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ type TYPE; expression THING, E; @@ ( vzalloc( - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | vzalloc( - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression COUNT; typedef u8; typedef __u8; @@ ( vzalloc( - sizeof(u8) * (COUNT) + COUNT , ...) | vzalloc( - sizeof(__u8) * (COUNT) + COUNT , ...) | vzalloc( - sizeof(char) * (COUNT) + COUNT , ...) | vzalloc( - sizeof(unsigned char) * (COUNT) + COUNT , ...) | vzalloc( - sizeof(u8) * COUNT + COUNT , ...) | vzalloc( - sizeof(__u8) * COUNT + COUNT , ...) | vzalloc( - sizeof(char) * COUNT + COUNT , ...) | vzalloc( - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( vzalloc( - sizeof(TYPE) * (COUNT_ID) + array_size(COUNT_ID, sizeof(TYPE)) , ...) | vzalloc( - sizeof(TYPE) * COUNT_ID + array_size(COUNT_ID, sizeof(TYPE)) , ...) | vzalloc( - sizeof(TYPE) * (COUNT_CONST) + array_size(COUNT_CONST, sizeof(TYPE)) , ...) | vzalloc( - sizeof(TYPE) * COUNT_CONST + array_size(COUNT_CONST, sizeof(TYPE)) , ...) | vzalloc( - sizeof(THING) * (COUNT_ID) + array_size(COUNT_ID, sizeof(THING)) , ...) | vzalloc( - sizeof(THING) * COUNT_ID + array_size(COUNT_ID, sizeof(THING)) , ...) | vzalloc( - sizeof(THING) * (COUNT_CONST) + array_size(COUNT_CONST, sizeof(THING)) , ...) | vzalloc( - sizeof(THING) * COUNT_CONST + array_size(COUNT_CONST, sizeof(THING)) , ...) ) // 2-factor product, only identifiers. @@ identifier SIZE, COUNT; @@ vzalloc( - SIZE * COUNT + array_size(COUNT, SIZE) , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( vzalloc( - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | vzalloc( - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | vzalloc( - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | vzalloc( - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | vzalloc( - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | vzalloc( - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | vzalloc( - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | vzalloc( - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( vzalloc( - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | vzalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | vzalloc( - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | vzalloc( - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | vzalloc( - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | vzalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ identifier STRIDE, SIZE, COUNT; @@ ( vzalloc( - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | vzalloc( - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | vzalloc( - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | vzalloc( - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | vzalloc( - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | vzalloc( - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | vzalloc( - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | vzalloc( - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products // when they're not all constants... @@ expression E1, E2, E3; constant C1, C2, C3; @@ ( vzalloc(C1 * C2 * C3, ...) | vzalloc( - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants. @@ expression E1, E2; constant C1, C2; @@ ( vzalloc(C1 * C2, ...) | vzalloc( - E1 * E2 + array_size(E1, E2) , ...) ) Signed-off-by: NKees Cook <keescook@chromium.org>
-
由 Kees Cook 提交于
The vmalloc() function has no 2-factor argument form, so multiplication factors need to be wrapped in array_size(). This patch replaces cases of: vmalloc(a * b) with: vmalloc(array_size(a, b)) as well as handling cases of: vmalloc(a * b * c) with: vmalloc(array3_size(a, b, c)) This does, however, attempt to ignore constant size factors like: vmalloc(4 * 1024) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ type TYPE; expression THING, E; @@ ( vmalloc( - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | vmalloc( - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression COUNT; typedef u8; typedef __u8; @@ ( vmalloc( - sizeof(u8) * (COUNT) + COUNT , ...) | vmalloc( - sizeof(__u8) * (COUNT) + COUNT , ...) | vmalloc( - sizeof(char) * (COUNT) + COUNT , ...) | vmalloc( - sizeof(unsigned char) * (COUNT) + COUNT , ...) | vmalloc( - sizeof(u8) * COUNT + COUNT , ...) | vmalloc( - sizeof(__u8) * COUNT + COUNT , ...) | vmalloc( - sizeof(char) * COUNT + COUNT , ...) | vmalloc( - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( vmalloc( - sizeof(TYPE) * (COUNT_ID) + array_size(COUNT_ID, sizeof(TYPE)) , ...) | vmalloc( - sizeof(TYPE) * COUNT_ID + array_size(COUNT_ID, sizeof(TYPE)) , ...) | vmalloc( - sizeof(TYPE) * (COUNT_CONST) + array_size(COUNT_CONST, sizeof(TYPE)) , ...) | vmalloc( - sizeof(TYPE) * COUNT_CONST + array_size(COUNT_CONST, sizeof(TYPE)) , ...) | vmalloc( - sizeof(THING) * (COUNT_ID) + array_size(COUNT_ID, sizeof(THING)) , ...) | vmalloc( - sizeof(THING) * COUNT_ID + array_size(COUNT_ID, sizeof(THING)) , ...) | vmalloc( - sizeof(THING) * (COUNT_CONST) + array_size(COUNT_CONST, sizeof(THING)) , ...) | vmalloc( - sizeof(THING) * COUNT_CONST + array_size(COUNT_CONST, sizeof(THING)) , ...) ) // 2-factor product, only identifiers. @@ identifier SIZE, COUNT; @@ vmalloc( - SIZE * COUNT + array_size(COUNT, SIZE) , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( vmalloc( - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | vmalloc( - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | vmalloc( - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | vmalloc( - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | vmalloc( - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | vmalloc( - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | vmalloc( - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | vmalloc( - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( vmalloc( - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | vmalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | vmalloc( - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | vmalloc( - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | vmalloc( - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | vmalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ identifier STRIDE, SIZE, COUNT; @@ ( vmalloc( - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | vmalloc( - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | vmalloc( - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | vmalloc( - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | vmalloc( - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | vmalloc( - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | vmalloc( - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | vmalloc( - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products // when they're not all constants... @@ expression E1, E2, E3; constant C1, C2, C3; @@ ( vmalloc(C1 * C2 * C3, ...) | vmalloc( - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants. @@ expression E1, E2; constant C1, C2; @@ ( vmalloc(C1 * C2, ...) | vmalloc( - E1 * E2 + array_size(E1, E2) , ...) ) Signed-off-by: NKees Cook <keescook@chromium.org>
-
由 Kees Cook 提交于
The devm_kzalloc() function has a 2-factor argument form, devm_kcalloc(). This patch replaces cases of: devm_kzalloc(handle, a * b, gfp) with: devm_kcalloc(handle, a * b, gfp) as well as handling cases of: devm_kzalloc(handle, a * b * c, gfp) with: devm_kzalloc(handle, array3_size(a, b, c), gfp) as it's slightly less ugly than: devm_kcalloc(handle, array_size(a, b), c, gfp) This does, however, attempt to ignore constant size factors like: devm_kzalloc(handle, 4 * 1024, gfp) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. Some manual whitespace fixes were needed in this patch, as Coccinelle really liked to write "=devm_kcalloc..." instead of "= devm_kcalloc...". The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ expression HANDLE; type TYPE; expression THING, E; @@ ( devm_kzalloc(HANDLE, - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | devm_kzalloc(HANDLE, - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression HANDLE; expression COUNT; typedef u8; typedef __u8; @@ ( devm_kzalloc(HANDLE, - sizeof(u8) * (COUNT) + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(__u8) * (COUNT) + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(char) * (COUNT) + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(unsigned char) * (COUNT) + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(u8) * COUNT + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(__u8) * COUNT + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(char) * COUNT + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ expression HANDLE; type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * (COUNT_ID) + COUNT_ID, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * COUNT_ID + COUNT_ID, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * (COUNT_CONST) + COUNT_CONST, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * COUNT_CONST + COUNT_CONST, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * (COUNT_ID) + COUNT_ID, sizeof(THING) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * COUNT_ID + COUNT_ID, sizeof(THING) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * (COUNT_CONST) + COUNT_CONST, sizeof(THING) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * COUNT_CONST + COUNT_CONST, sizeof(THING) , ...) ) // 2-factor product, only identifiers. @@ expression HANDLE; identifier SIZE, COUNT; @@ - devm_kzalloc + devm_kcalloc (HANDLE, - SIZE * COUNT + COUNT, SIZE , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression HANDLE; expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( devm_kzalloc(HANDLE, - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression HANDLE; expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( devm_kzalloc(HANDLE, - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ expression HANDLE; identifier STRIDE, SIZE, COUNT; @@ ( devm_kzalloc(HANDLE, - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products, // when they're not all constants... @@ expression HANDLE; expression E1, E2, E3; constant C1, C2, C3; @@ ( devm_kzalloc(HANDLE, C1 * C2 * C3, ...) | devm_kzalloc(HANDLE, - (E1) * E2 * E3 + array3_size(E1, E2, E3) , ...) | devm_kzalloc(HANDLE, - (E1) * (E2) * E3 + array3_size(E1, E2, E3) , ...) | devm_kzalloc(HANDLE, - (E1) * (E2) * (E3) + array3_size(E1, E2, E3) , ...) | devm_kzalloc(HANDLE, - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants, // keeping sizeof() as the second factor argument. @@ expression HANDLE; expression THING, E1, E2; type TYPE; constant C1, C2, C3; @@ ( devm_kzalloc(HANDLE, sizeof(THING) * C2, ...) | devm_kzalloc(HANDLE, sizeof(TYPE) * C2, ...) | devm_kzalloc(HANDLE, C1 * C2 * C3, ...) | devm_kzalloc(HANDLE, C1 * C2, ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * (E2) + E2, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * E2 + E2, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * (E2) + E2, sizeof(THING) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * E2 + E2, sizeof(THING) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - (E1) * E2 + E1, E2 , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - (E1) * (E2) + E1, E2 , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - E1 * E2 + E1, E2 , ...) ) Signed-off-by: NKees Cook <keescook@chromium.org>
-
由 Kees Cook 提交于
The devm_kmalloc() function has a 2-factor argument form, devm_kmalloc_array(). This patch replaces cases of: devm_kmalloc(handle, a * b, gfp) with: devm_kmalloc_array(handle, a * b, gfp) as well as handling cases of: devm_kmalloc(handle, a * b * c, gfp) with: devm_kmalloc(handle, array3_size(a, b, c), gfp) as it's slightly less ugly than: devm_kmalloc_array(handle, array_size(a, b), c, gfp) This does, however, attempt to ignore constant size factors like: devm_kmalloc(handle, 4 * 1024, gfp) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. Some manual whitespace fixes were needed in this patch, as Coccinelle really liked to write "=devm_kmalloc..." instead of "= devm_kmalloc...". The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ expression HANDLE; type TYPE; expression THING, E; @@ ( devm_kmalloc(HANDLE, - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | devm_kmalloc(HANDLE, - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression HANDLE; expression COUNT; typedef u8; typedef __u8; @@ ( devm_kmalloc(HANDLE, - sizeof(u8) * (COUNT) + COUNT , ...) | devm_kmalloc(HANDLE, - sizeof(__u8) * (COUNT) + COUNT , ...) | devm_kmalloc(HANDLE, - sizeof(char) * (COUNT) + COUNT , ...) | devm_kmalloc(HANDLE, - sizeof(unsigned char) * (COUNT) + COUNT , ...) | devm_kmalloc(HANDLE, - sizeof(u8) * COUNT + COUNT , ...) | devm_kmalloc(HANDLE, - sizeof(__u8) * COUNT + COUNT , ...) | devm_kmalloc(HANDLE, - sizeof(char) * COUNT + COUNT , ...) | devm_kmalloc(HANDLE, - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ expression HANDLE; type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( - devm_kmalloc + devm_kmalloc_array (HANDLE, - sizeof(TYPE) * (COUNT_ID) + COUNT_ID, sizeof(TYPE) , ...) | - devm_kmalloc + devm_kmalloc_array (HANDLE, - sizeof(TYPE) * COUNT_ID + COUNT_ID, sizeof(TYPE) , ...) | - devm_kmalloc + devm_kmalloc_array (HANDLE, - sizeof(TYPE) * (COUNT_CONST) + COUNT_CONST, sizeof(TYPE) , ...) | - devm_kmalloc + devm_kmalloc_array (HANDLE, - sizeof(TYPE) * COUNT_CONST + COUNT_CONST, sizeof(TYPE) , ...) | - devm_kmalloc + devm_kmalloc_array (HANDLE, - sizeof(THING) * (COUNT_ID) + COUNT_ID, sizeof(THING) , ...) | - devm_kmalloc + devm_kmalloc_array (HANDLE, - sizeof(THING) * COUNT_ID + COUNT_ID, sizeof(THING) , ...) | - devm_kmalloc + devm_kmalloc_array (HANDLE, - sizeof(THING) * (COUNT_CONST) + COUNT_CONST, sizeof(THING) , ...) | - devm_kmalloc + devm_kmalloc_array (HANDLE, - sizeof(THING) * COUNT_CONST + COUNT_CONST, sizeof(THING) , ...) ) // 2-factor product, only identifiers. @@ expression HANDLE; identifier SIZE, COUNT; @@ - devm_kmalloc + devm_kmalloc_array (HANDLE, - SIZE * COUNT + COUNT, SIZE , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression HANDLE; expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( devm_kmalloc(HANDLE, - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | devm_kmalloc(HANDLE, - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | devm_kmalloc(HANDLE, - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | devm_kmalloc(HANDLE, - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | devm_kmalloc(HANDLE, - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | devm_kmalloc(HANDLE, - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | devm_kmalloc(HANDLE, - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | devm_kmalloc(HANDLE, - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression HANDLE; expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( devm_kmalloc(HANDLE, - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | devm_kmalloc(HANDLE, - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | devm_kmalloc(HANDLE, - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | devm_kmalloc(HANDLE, - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | devm_kmalloc(HANDLE, - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | devm_kmalloc(HANDLE, - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ expression HANDLE; identifier STRIDE, SIZE, COUNT; @@ ( devm_kmalloc(HANDLE, - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kmalloc(HANDLE, - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kmalloc(HANDLE, - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kmalloc(HANDLE, - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kmalloc(HANDLE, - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kmalloc(HANDLE, - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kmalloc(HANDLE, - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kmalloc(HANDLE, - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products, // when they're not all constants... @@ expression HANDLE; expression E1, E2, E3; constant C1, C2, C3; @@ ( devm_kmalloc(HANDLE, C1 * C2 * C3, ...) | devm_kmalloc(HANDLE, - (E1) * E2 * E3 + array3_size(E1, E2, E3) , ...) | devm_kmalloc(HANDLE, - (E1) * (E2) * E3 + array3_size(E1, E2, E3) , ...) | devm_kmalloc(HANDLE, - (E1) * (E2) * (E3) + array3_size(E1, E2, E3) , ...) | devm_kmalloc(HANDLE, - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants, // keeping sizeof() as the second factor argument. @@ expression HANDLE; expression THING, E1, E2; type TYPE; constant C1, C2, C3; @@ ( devm_kmalloc(HANDLE, sizeof(THING) * C2, ...) | devm_kmalloc(HANDLE, sizeof(TYPE) * C2, ...) | devm_kmalloc(HANDLE, C1 * C2 * C3, ...) | devm_kmalloc(HANDLE, C1 * C2, ...) | - devm_kmalloc + devm_kmalloc_array (HANDLE, - sizeof(TYPE) * (E2) + E2, sizeof(TYPE) , ...) | - devm_kmalloc + devm_kmalloc_array (HANDLE, - sizeof(TYPE) * E2 + E2, sizeof(TYPE) , ...) | - devm_kmalloc + devm_kmalloc_array (HANDLE, - sizeof(THING) * (E2) + E2, sizeof(THING) , ...) | - devm_kmalloc + devm_kmalloc_array (HANDLE, - sizeof(THING) * E2 + E2, sizeof(THING) , ...) | - devm_kmalloc + devm_kmalloc_array (HANDLE, - (E1) * E2 + E1, E2 , ...) | - devm_kmalloc + devm_kmalloc_array (HANDLE, - (E1) * (E2) + E1, E2 , ...) | - devm_kmalloc + devm_kmalloc_array (HANDLE, - E1 * E2 + E1, E2 , ...) ) Signed-off-by: NKees Cook <keescook@chromium.org>
-
由 Kees Cook 提交于
The kvzalloc() function has a 2-factor argument form, kvcalloc(). This patch replaces cases of: kvzalloc(a * b, gfp) with: kvcalloc(a * b, gfp) as well as handling cases of: kvzalloc(a * b * c, gfp) with: kvzalloc(array3_size(a, b, c), gfp) as it's slightly less ugly than: kvcalloc(array_size(a, b), c, gfp) This does, however, attempt to ignore constant size factors like: kvzalloc(4 * 1024, gfp) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ type TYPE; expression THING, E; @@ ( kvzalloc( - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | kvzalloc( - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression COUNT; typedef u8; typedef __u8; @@ ( kvzalloc( - sizeof(u8) * (COUNT) + COUNT , ...) | kvzalloc( - sizeof(__u8) * (COUNT) + COUNT , ...) | kvzalloc( - sizeof(char) * (COUNT) + COUNT , ...) | kvzalloc( - sizeof(unsigned char) * (COUNT) + COUNT , ...) | kvzalloc( - sizeof(u8) * COUNT + COUNT , ...) | kvzalloc( - sizeof(__u8) * COUNT + COUNT , ...) | kvzalloc( - sizeof(char) * COUNT + COUNT , ...) | kvzalloc( - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( - kvzalloc + kvcalloc ( - sizeof(TYPE) * (COUNT_ID) + COUNT_ID, sizeof(TYPE) , ...) | - kvzalloc + kvcalloc ( - sizeof(TYPE) * COUNT_ID + COUNT_ID, sizeof(TYPE) , ...) | - kvzalloc + kvcalloc ( - sizeof(TYPE) * (COUNT_CONST) + COUNT_CONST, sizeof(TYPE) , ...) | - kvzalloc + kvcalloc ( - sizeof(TYPE) * COUNT_CONST + COUNT_CONST, sizeof(TYPE) , ...) | - kvzalloc + kvcalloc ( - sizeof(THING) * (COUNT_ID) + COUNT_ID, sizeof(THING) , ...) | - kvzalloc + kvcalloc ( - sizeof(THING) * COUNT_ID + COUNT_ID, sizeof(THING) , ...) | - kvzalloc + kvcalloc ( - sizeof(THING) * (COUNT_CONST) + COUNT_CONST, sizeof(THING) , ...) | - kvzalloc + kvcalloc ( - sizeof(THING) * COUNT_CONST + COUNT_CONST, sizeof(THING) , ...) ) // 2-factor product, only identifiers. @@ identifier SIZE, COUNT; @@ - kvzalloc + kvcalloc ( - SIZE * COUNT + COUNT, SIZE , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( kvzalloc( - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kvzalloc( - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kvzalloc( - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kvzalloc( - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kvzalloc( - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kvzalloc( - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kvzalloc( - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kvzalloc( - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( kvzalloc( - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kvzalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kvzalloc( - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kvzalloc( - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kvzalloc( - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | kvzalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ identifier STRIDE, SIZE, COUNT; @@ ( kvzalloc( - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kvzalloc( - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kvzalloc( - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kvzalloc( - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kvzalloc( - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kvzalloc( - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kvzalloc( - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kvzalloc( - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products, // when they're not all constants... @@ expression E1, E2, E3; constant C1, C2, C3; @@ ( kvzalloc(C1 * C2 * C3, ...) | kvzalloc( - (E1) * E2 * E3 + array3_size(E1, E2, E3) , ...) | kvzalloc( - (E1) * (E2) * E3 + array3_size(E1, E2, E3) , ...) | kvzalloc( - (E1) * (E2) * (E3) + array3_size(E1, E2, E3) , ...) | kvzalloc( - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants, // keeping sizeof() as the second factor argument. @@ expression THING, E1, E2; type TYPE; constant C1, C2, C3; @@ ( kvzalloc(sizeof(THING) * C2, ...) | kvzalloc(sizeof(TYPE) * C2, ...) | kvzalloc(C1 * C2 * C3, ...) | kvzalloc(C1 * C2, ...) | - kvzalloc + kvcalloc ( - sizeof(TYPE) * (E2) + E2, sizeof(TYPE) , ...) | - kvzalloc + kvcalloc ( - sizeof(TYPE) * E2 + E2, sizeof(TYPE) , ...) | - kvzalloc + kvcalloc ( - sizeof(THING) * (E2) + E2, sizeof(THING) , ...) | - kvzalloc + kvcalloc ( - sizeof(THING) * E2 + E2, sizeof(THING) , ...) | - kvzalloc + kvcalloc ( - (E1) * E2 + E1, E2 , ...) | - kvzalloc + kvcalloc ( - (E1) * (E2) + E1, E2 , ...) | - kvzalloc + kvcalloc ( - E1 * E2 + E1, E2 , ...) ) Signed-off-by: NKees Cook <keescook@chromium.org>
-
由 Kees Cook 提交于
The kvmalloc() function has a 2-factor argument form, kvmalloc_array(). This patch replaces cases of: kvmalloc(a * b, gfp) with: kvmalloc_array(a * b, gfp) as well as handling cases of: kvmalloc(a * b * c, gfp) with: kvmalloc(array3_size(a, b, c), gfp) as it's slightly less ugly than: kvmalloc_array(array_size(a, b), c, gfp) This does, however, attempt to ignore constant size factors like: kvmalloc(4 * 1024, gfp) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ type TYPE; expression THING, E; @@ ( kvmalloc( - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | kvmalloc( - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression COUNT; typedef u8; typedef __u8; @@ ( kvmalloc( - sizeof(u8) * (COUNT) + COUNT , ...) | kvmalloc( - sizeof(__u8) * (COUNT) + COUNT , ...) | kvmalloc( - sizeof(char) * (COUNT) + COUNT , ...) | kvmalloc( - sizeof(unsigned char) * (COUNT) + COUNT , ...) | kvmalloc( - sizeof(u8) * COUNT + COUNT , ...) | kvmalloc( - sizeof(__u8) * COUNT + COUNT , ...) | kvmalloc( - sizeof(char) * COUNT + COUNT , ...) | kvmalloc( - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( - kvmalloc + kvmalloc_array ( - sizeof(TYPE) * (COUNT_ID) + COUNT_ID, sizeof(TYPE) , ...) | - kvmalloc + kvmalloc_array ( - sizeof(TYPE) * COUNT_ID + COUNT_ID, sizeof(TYPE) , ...) | - kvmalloc + kvmalloc_array ( - sizeof(TYPE) * (COUNT_CONST) + COUNT_CONST, sizeof(TYPE) , ...) | - kvmalloc + kvmalloc_array ( - sizeof(TYPE) * COUNT_CONST + COUNT_CONST, sizeof(TYPE) , ...) | - kvmalloc + kvmalloc_array ( - sizeof(THING) * (COUNT_ID) + COUNT_ID, sizeof(THING) , ...) | - kvmalloc + kvmalloc_array ( - sizeof(THING) * COUNT_ID + COUNT_ID, sizeof(THING) , ...) | - kvmalloc + kvmalloc_array ( - sizeof(THING) * (COUNT_CONST) + COUNT_CONST, sizeof(THING) , ...) | - kvmalloc + kvmalloc_array ( - sizeof(THING) * COUNT_CONST + COUNT_CONST, sizeof(THING) , ...) ) // 2-factor product, only identifiers. @@ identifier SIZE, COUNT; @@ - kvmalloc + kvmalloc_array ( - SIZE * COUNT + COUNT, SIZE , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( kvmalloc( - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kvmalloc( - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kvmalloc( - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kvmalloc( - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kvmalloc( - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kvmalloc( - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kvmalloc( - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kvmalloc( - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( kvmalloc( - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kvmalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kvmalloc( - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kvmalloc( - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kvmalloc( - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | kvmalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ identifier STRIDE, SIZE, COUNT; @@ ( kvmalloc( - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kvmalloc( - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kvmalloc( - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kvmalloc( - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kvmalloc( - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kvmalloc( - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kvmalloc( - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kvmalloc( - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products, // when they're not all constants... @@ expression E1, E2, E3; constant C1, C2, C3; @@ ( kvmalloc(C1 * C2 * C3, ...) | kvmalloc( - (E1) * E2 * E3 + array3_size(E1, E2, E3) , ...) | kvmalloc( - (E1) * (E2) * E3 + array3_size(E1, E2, E3) , ...) | kvmalloc( - (E1) * (E2) * (E3) + array3_size(E1, E2, E3) , ...) | kvmalloc( - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants, // keeping sizeof() as the second factor argument. @@ expression THING, E1, E2; type TYPE; constant C1, C2, C3; @@ ( kvmalloc(sizeof(THING) * C2, ...) | kvmalloc(sizeof(TYPE) * C2, ...) | kvmalloc(C1 * C2 * C3, ...) | kvmalloc(C1 * C2, ...) | - kvmalloc + kvmalloc_array ( - sizeof(TYPE) * (E2) + E2, sizeof(TYPE) , ...) | - kvmalloc + kvmalloc_array ( - sizeof(TYPE) * E2 + E2, sizeof(TYPE) , ...) | - kvmalloc + kvmalloc_array ( - sizeof(THING) * (E2) + E2, sizeof(THING) , ...) | - kvmalloc + kvmalloc_array ( - sizeof(THING) * E2 + E2, sizeof(THING) , ...) | - kvmalloc + kvmalloc_array ( - (E1) * E2 + E1, E2 , ...) | - kvmalloc + kvmalloc_array ( - (E1) * (E2) + E1, E2 , ...) | - kvmalloc + kvmalloc_array ( - E1 * E2 + E1, E2 , ...) ) Signed-off-by: NKees Cook <keescook@chromium.org>
-
由 Kees Cook 提交于
The kzalloc_node() function has a 2-factor argument form, kcalloc_node(). This patch replaces cases of: kzalloc_node(a * b, gfp, node) with: kcalloc_node(a * b, gfp, node) as well as handling cases of: kzalloc_node(a * b * c, gfp, node) with: kzalloc_node(array3_size(a, b, c), gfp, node) as it's slightly less ugly than: kcalloc_node(array_size(a, b), c, gfp, node) This does, however, attempt to ignore constant size factors like: kzalloc_node(4 * 1024, gfp, node) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ type TYPE; expression THING, E; @@ ( kzalloc_node( - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | kzalloc_node( - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression COUNT; typedef u8; typedef __u8; @@ ( kzalloc_node( - sizeof(u8) * (COUNT) + COUNT , ...) | kzalloc_node( - sizeof(__u8) * (COUNT) + COUNT , ...) | kzalloc_node( - sizeof(char) * (COUNT) + COUNT , ...) | kzalloc_node( - sizeof(unsigned char) * (COUNT) + COUNT , ...) | kzalloc_node( - sizeof(u8) * COUNT + COUNT , ...) | kzalloc_node( - sizeof(__u8) * COUNT + COUNT , ...) | kzalloc_node( - sizeof(char) * COUNT + COUNT , ...) | kzalloc_node( - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( - kzalloc_node + kcalloc_node ( - sizeof(TYPE) * (COUNT_ID) + COUNT_ID, sizeof(TYPE) , ...) | - kzalloc_node + kcalloc_node ( - sizeof(TYPE) * COUNT_ID + COUNT_ID, sizeof(TYPE) , ...) | - kzalloc_node + kcalloc_node ( - sizeof(TYPE) * (COUNT_CONST) + COUNT_CONST, sizeof(TYPE) , ...) | - kzalloc_node + kcalloc_node ( - sizeof(TYPE) * COUNT_CONST + COUNT_CONST, sizeof(TYPE) , ...) | - kzalloc_node + kcalloc_node ( - sizeof(THING) * (COUNT_ID) + COUNT_ID, sizeof(THING) , ...) | - kzalloc_node + kcalloc_node ( - sizeof(THING) * COUNT_ID + COUNT_ID, sizeof(THING) , ...) | - kzalloc_node + kcalloc_node ( - sizeof(THING) * (COUNT_CONST) + COUNT_CONST, sizeof(THING) , ...) | - kzalloc_node + kcalloc_node ( - sizeof(THING) * COUNT_CONST + COUNT_CONST, sizeof(THING) , ...) ) // 2-factor product, only identifiers. @@ identifier SIZE, COUNT; @@ - kzalloc_node + kcalloc_node ( - SIZE * COUNT + COUNT, SIZE , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( kzalloc_node( - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc_node( - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc_node( - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc_node( - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc_node( - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc_node( - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc_node( - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc_node( - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( kzalloc_node( - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kzalloc_node( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kzalloc_node( - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kzalloc_node( - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kzalloc_node( - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | kzalloc_node( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ identifier STRIDE, SIZE, COUNT; @@ ( kzalloc_node( - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc_node( - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc_node( - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc_node( - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc_node( - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc_node( - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc_node( - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc_node( - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products, // when they're not all constants... @@ expression E1, E2, E3; constant C1, C2, C3; @@ ( kzalloc_node(C1 * C2 * C3, ...) | kzalloc_node( - (E1) * E2 * E3 + array3_size(E1, E2, E3) , ...) | kzalloc_node( - (E1) * (E2) * E3 + array3_size(E1, E2, E3) , ...) | kzalloc_node( - (E1) * (E2) * (E3) + array3_size(E1, E2, E3) , ...) | kzalloc_node( - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants, // keeping sizeof() as the second factor argument. @@ expression THING, E1, E2; type TYPE; constant C1, C2, C3; @@ ( kzalloc_node(sizeof(THING) * C2, ...) | kzalloc_node(sizeof(TYPE) * C2, ...) | kzalloc_node(C1 * C2 * C3, ...) | kzalloc_node(C1 * C2, ...) | - kzalloc_node + kcalloc_node ( - sizeof(TYPE) * (E2) + E2, sizeof(TYPE) , ...) | - kzalloc_node + kcalloc_node ( - sizeof(TYPE) * E2 + E2, sizeof(TYPE) , ...) | - kzalloc_node + kcalloc_node ( - sizeof(THING) * (E2) + E2, sizeof(THING) , ...) | - kzalloc_node + kcalloc_node ( - sizeof(THING) * E2 + E2, sizeof(THING) , ...) | - kzalloc_node + kcalloc_node ( - (E1) * E2 + E1, E2 , ...) | - kzalloc_node + kcalloc_node ( - (E1) * (E2) + E1, E2 , ...) | - kzalloc_node + kcalloc_node ( - E1 * E2 + E1, E2 , ...) ) Signed-off-by: NKees Cook <keescook@chromium.org>
-
由 Kees Cook 提交于
The kzalloc() function has a 2-factor argument form, kcalloc(). This patch replaces cases of: kzalloc(a * b, gfp) with: kcalloc(a * b, gfp) as well as handling cases of: kzalloc(a * b * c, gfp) with: kzalloc(array3_size(a, b, c), gfp) as it's slightly less ugly than: kzalloc_array(array_size(a, b), c, gfp) This does, however, attempt to ignore constant size factors like: kzalloc(4 * 1024, gfp) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ type TYPE; expression THING, E; @@ ( kzalloc( - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | kzalloc( - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression COUNT; typedef u8; typedef __u8; @@ ( kzalloc( - sizeof(u8) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(__u8) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(char) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(unsigned char) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(u8) * COUNT + COUNT , ...) | kzalloc( - sizeof(__u8) * COUNT + COUNT , ...) | kzalloc( - sizeof(char) * COUNT + COUNT , ...) | kzalloc( - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( - kzalloc + kcalloc ( - sizeof(TYPE) * (COUNT_ID) + COUNT_ID, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * COUNT_ID + COUNT_ID, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * (COUNT_CONST) + COUNT_CONST, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * COUNT_CONST + COUNT_CONST, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * (COUNT_ID) + COUNT_ID, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * COUNT_ID + COUNT_ID, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * (COUNT_CONST) + COUNT_CONST, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * COUNT_CONST + COUNT_CONST, sizeof(THING) , ...) ) // 2-factor product, only identifiers. @@ identifier SIZE, COUNT; @@ - kzalloc + kcalloc ( - SIZE * COUNT + COUNT, SIZE , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( kzalloc( - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc( - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc( - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc( - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( kzalloc( - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kzalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kzalloc( - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kzalloc( - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kzalloc( - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | kzalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ identifier STRIDE, SIZE, COUNT; @@ ( kzalloc( - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products, // when they're not all constants... @@ expression E1, E2, E3; constant C1, C2, C3; @@ ( kzalloc(C1 * C2 * C3, ...) | kzalloc( - (E1) * E2 * E3 + array3_size(E1, E2, E3) , ...) | kzalloc( - (E1) * (E2) * E3 + array3_size(E1, E2, E3) , ...) | kzalloc( - (E1) * (E2) * (E3) + array3_size(E1, E2, E3) , ...) | kzalloc( - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants, // keeping sizeof() as the second factor argument. @@ expression THING, E1, E2; type TYPE; constant C1, C2, C3; @@ ( kzalloc(sizeof(THING) * C2, ...) | kzalloc(sizeof(TYPE) * C2, ...) | kzalloc(C1 * C2 * C3, ...) | kzalloc(C1 * C2, ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * (E2) + E2, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * E2 + E2, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * (E2) + E2, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * E2 + E2, sizeof(THING) , ...) | - kzalloc + kcalloc ( - (E1) * E2 + E1, E2 , ...) | - kzalloc + kcalloc ( - (E1) * (E2) + E1, E2 , ...) | - kzalloc + kcalloc ( - E1 * E2 + E1, E2 , ...) ) Signed-off-by: NKees Cook <keescook@chromium.org>
-
由 Kees Cook 提交于
The kmalloc() function has a 2-factor argument form, kmalloc_array(). This patch replaces cases of: kmalloc(a * b, gfp) with: kmalloc_array(a * b, gfp) as well as handling cases of: kmalloc(a * b * c, gfp) with: kmalloc(array3_size(a, b, c), gfp) as it's slightly less ugly than: kmalloc_array(array_size(a, b), c, gfp) This does, however, attempt to ignore constant size factors like: kmalloc(4 * 1024, gfp) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. The tools/ directory was manually excluded, since it has its own implementation of kmalloc(). The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ type TYPE; expression THING, E; @@ ( kmalloc( - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | kmalloc( - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression COUNT; typedef u8; typedef __u8; @@ ( kmalloc( - sizeof(u8) * (COUNT) + COUNT , ...) | kmalloc( - sizeof(__u8) * (COUNT) + COUNT , ...) | kmalloc( - sizeof(char) * (COUNT) + COUNT , ...) | kmalloc( - sizeof(unsigned char) * (COUNT) + COUNT , ...) | kmalloc( - sizeof(u8) * COUNT + COUNT , ...) | kmalloc( - sizeof(__u8) * COUNT + COUNT , ...) | kmalloc( - sizeof(char) * COUNT + COUNT , ...) | kmalloc( - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( - kmalloc + kmalloc_array ( - sizeof(TYPE) * (COUNT_ID) + COUNT_ID, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(TYPE) * COUNT_ID + COUNT_ID, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(TYPE) * (COUNT_CONST) + COUNT_CONST, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(TYPE) * COUNT_CONST + COUNT_CONST, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * (COUNT_ID) + COUNT_ID, sizeof(THING) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * COUNT_ID + COUNT_ID, sizeof(THING) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * (COUNT_CONST) + COUNT_CONST, sizeof(THING) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * COUNT_CONST + COUNT_CONST, sizeof(THING) , ...) ) // 2-factor product, only identifiers. @@ identifier SIZE, COUNT; @@ - kmalloc + kmalloc_array ( - SIZE * COUNT + COUNT, SIZE , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( kmalloc( - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kmalloc( - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kmalloc( - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kmalloc( - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kmalloc( - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kmalloc( - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kmalloc( - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kmalloc( - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( kmalloc( - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kmalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kmalloc( - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kmalloc( - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kmalloc( - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | kmalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ identifier STRIDE, SIZE, COUNT; @@ ( kmalloc( - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products, // when they're not all constants... @@ expression E1, E2, E3; constant C1, C2, C3; @@ ( kmalloc(C1 * C2 * C3, ...) | kmalloc( - (E1) * E2 * E3 + array3_size(E1, E2, E3) , ...) | kmalloc( - (E1) * (E2) * E3 + array3_size(E1, E2, E3) , ...) | kmalloc( - (E1) * (E2) * (E3) + array3_size(E1, E2, E3) , ...) | kmalloc( - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants, // keeping sizeof() as the second factor argument. @@ expression THING, E1, E2; type TYPE; constant C1, C2, C3; @@ ( kmalloc(sizeof(THING) * C2, ...) | kmalloc(sizeof(TYPE) * C2, ...) | kmalloc(C1 * C2 * C3, ...) | kmalloc(C1 * C2, ...) | - kmalloc + kmalloc_array ( - sizeof(TYPE) * (E2) + E2, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(TYPE) * E2 + E2, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * (E2) + E2, sizeof(THING) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * E2 + E2, sizeof(THING) , ...) | - kmalloc + kmalloc_array ( - (E1) * E2 + E1, E2 , ...) | - kmalloc + kmalloc_array ( - (E1) * (E2) + E1, E2 , ...) | - kmalloc + kmalloc_array ( - E1 * E2 + E1, E2 , ...) ) Signed-off-by: NKees Cook <keescook@chromium.org>
-