CSA action frame content should be processed as variable IEs
rather than fixed to make it extensible. Unify the code and
process them just like CSA in beacons to make it easier to
extend for HT/VHT.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The field is otherwise reserved, so we shouldn't read
and reject it, though any sane system will probably
have to set it to 0 anyway.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When a full scan 2.4 and 5 GHz scan is scheduled, but then the 2.4 GHz
part of the scan disables a 5.2 GHz channel due to, e.g. receiving
country or frequency information, that 5.2 GHz channel might already
be in the list of channels to scan next. Then, when the driver checks
if it should do a passive scan, that will return false and attempt an
active scan. This is not only wrong but can also lead to the iwlwifi
device firmware crashing since it checks regulatory as well.

Fix this by not setting the channel flags to just disabled but rather
OR'ing in the disabled flag. That way, even if the race happens, the
channel will be scanned passively which is still (mostly) correct.

Cc: stable@vger.kernel.org
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When the 1st rate control entry is a pre-HT rate we want to set
rts_cts_rate_idx "as the fastest basic rate that is not faster than the
data rate"(code comments).
But in case some bss allowed rate indexes are lower than the lowest bss
basic rate, if the rate control selects a rate among the formers for its
1st rate control entry, rts_cts_rate_idx remains 0 and is not a basic
rate index.
This commit sets rts_cts_rate_idx to the lowest bss basic rate index in
this situation.

Note that the code assumes that lowest indexes == lowest bitrates.
Signed-off-by: NKarl Beldan <karl.beldan@rivierawaves.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Johannes Berg notes mac80211 drivers which use
ieee80211_queue_stopped() really only want to know if they
previously requested a queue stop.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Some drivers need SSID in AP and IBSS mode. AP SSID is provided
through BSS_CHANGED_SSID notification. There was no easy way to
do the same for IBSS. In IBSS mode SSID is known but was not
stored in BSS configuration. Extend the AP-mode functionality
to also work in IBSS mode.
Signed-off-by: NMarek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Advertise STBC capabilities and MCS rates even if the AP
doesn't support them. This has always been the right thing
to do, but used to be problematic with some APs. Now WFA
testing requires this so re-enable it, problematic APs
would then presumably not pass the test and be fixed.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When AP interface is stopped ssid_len in the BSS configuration
isn't cleared which can confuse drivers when switching modes.
Set the length to zero when stopping the AP interface.
Signed-off-by: NMarek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

local->hw.conf maybe not be synced when recalcing whether radar is
enabled, sometimes leaving radar enabled even if it's not neccesary
anymore.

Fix this by:
 * setting radar_enabled when creating the chanctx
 * turning radar_enabled off before destroying the last channel context
Reported-by: NZefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The patch "mac80211: stringify mesh peering events" missed
an opportunity to print the peering state as a string.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Otherwise forwarded frames would keep the retry bit set
from the previous link transmission.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Properly register our mac80211_hwsim_driver, attach it to the platform bus.
Bind newly created hwsim devices to that driver, so that our wlan devices get
a proper "driver" sysfs attribute.

This makes mac80211_hwsim interfaces work with NetworkManager.
Signed-off-by: NMartin Pitt <martin.pitt@ubuntu.com>
[fix an old and a new message to not be line-broken,
 also fix the driver_register error path]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This (slightly) reduces the code size.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

If a new netdev (e.g. an AP VLAN) is created while the driver
has queues stopped, the new netdev queues will be started even
though they shouldn't. This will lead to frames accumulating
on the internal mac80211 pending queues instead of properly
being held on the netdev queues.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Given the (nested) switch statements, this code can't
be reached, so make it warn instead of manipulating
the carrier state which seems purposeful.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The netdev queues should always represent the state that
the driver gave them, so fiddling with them isn't really
appropriate in the mlme code. Also, since we stop queues
for flushing now, this really isn't necessary any more.

As the scan/offchannel code has also been modified to no
longer do this a while ago, remove the outdated smp_mb()
and comments about it.

While at it, also add a pair of braces that was missing.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

It's unlikely that an AP requires WMM mandatory admission control
for all access categories, and if it does then we still transmit
on the background AC without requesting admission. However, avoid
using uAPSD in this case since the implementation could run into
issues and might use other ACs etc.
Signed-off-by: NAlexander Bondar <alexander.bondar@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When a device is unplugged while suspended, mac80211 is
de-initialized and all interfaces are removed while no
state is actually present in the driver. This can cause
warnings and driver confusion.

Fix this by reordering the do_stop code to not call the
driver when it is suspended, i.e. when there's no state
in the driver anyway.

The previous patches removed a few corner cases in ROC
and virtual monitor interfaces so that now this is safe
to do and no state should be left over.
Reported-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

It has to be removed from the driver, but completely
destroying it helps handle unplug of a device during
suspend since then the channel context handling etc.
doesn't have to happen later when it's removed.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

They can't really be executed while suspended and could
trigger work warnings, so abort all ROC items. When the
system resumes the notifications about this will be
delivered to userspace which can then act accordingly
(though it will assume they were canceled/finished.)
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The code now explicitly calls ieee80211_configure_filter()
anyway, so nothing needs to be explained.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Most times that mesh_path_add() is called, it is followed by
a lookup to get the just-added mpath.  We can instead just
return the new mpath in the case that we allocated one (or the
existing one if already there), so do that.  Also, reorder the
code in mesh_path_add a bit so that we don't need to allocate
in the pre-existing case.
Signed-off-by: NBob Copeland <bob@cozybit.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The mesh hwmp debug message is a bit confusing. The "sending PREP
to %p" should be the MAC address of mesh STA that has originated
the PREQ message and the "received PREP from %pM" should be the MAC
address of the mesh STA that has originated the PREP message.
Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Instead of open-coding the accesses and length check do
the length check in the IE parser and assign a struct
pointer for use in the remaining code.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

It's always just one byte, so check for that and
remove the length field from the parser struct.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

It's always just one byte, so check for that and
remove the length field from the parser struct.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There's no need to parse IEs that aren't used
so just remove them.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The master interface no longer exists ... and hasn't for
a few years now, so remove this reference :-)
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

I don't think we should send the events unless it was actually
a beacon that was lost...not just any probe of an AP.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Beacon-timeout and number of beacon loss events.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Drivers can now advertise VHT support even if they don't use channel
contexts.
Signed-off-by: NKarl Beldan <karl.beldan@rivierawaves.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

It is possible since the global hw config and local switched to
cfg80211_chan_def.
Signed-off-by: NKarl Beldan <karl.beldan@rivierawaves.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Drivers that don't use chanctxes cannot perform VHT association because
they still use a "backward compatibility" pair of {ieee80211_channel,
nl80211_channel_type} in ieee80211_conf and ieee80211_local.
Signed-off-by: NKarl Beldan <karl.beldan@rivierawaves.com>
[fix kernel-doc]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

mac80211 currently sets uAPSD parameters to have VO AC trigger-
and delivery-enabled, with maximum service period length.

Allow drivers to change these default settings since different
uAPSD client implementations may handle errors differently and
be able to recover from some errors.

Note: some APs may not function correctly if one or all ACs are
trigger- and delivery-enabled, see
http://thread.gmane.org/gmane.linux.kernel.wireless.general/93577.
We retested with this AP and later firmware doesn't have this
bug any more.
Signed-off-by: NAlexander Bondar <alexander.bondar@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Instead of having an SKB all the time, use a beacon_data struct
with just the information required. This also allows removing a
synchronize_rcu() and using kfree_rcu() instead.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

If we don't disable beaconing, the driver might attempt
to continue, but would fail to request a beacon. That's
strange, so disable beaconing first.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This was forgotten from the commit that added support for FT
operations with drivers that implement SME.
Signed-off-by: NJouni Malinen <j@w1.fi>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add P2P NoA settings for STA mode.
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
[fix docs]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Use ieee80211_p2p_noa_attr structure during
P2P_PS (oppps) detection.
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add P2P Notice of Absence attribute structure.
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>