The PHY's EEE settings are already accessed by the DSA layer through the
Marvell PHY driver and there is nothing to be done for switch's MACs.

Remove all EEE support from the mv88e6xxx driver and simply return 0
from the EEE ops.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of relying on a bitmap flag, add a new multi_chip info flag to
describe the presence of the indirect SMI access though the two device
registers 0x0 and 0x1.

All remaining capabilities and flags are now unused. Remove the
mv88e6xxx_cap enum and the info flags bitmaps.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 88E6352 family supports Energy Detect and has one bit for Sense and
one bit for periodically transmit NLP (Energy Detect+TM). The 88E6390
family adds another bit to distinguish Auto or SW wake-up. Chips
supporting EEE all have an EEE Enabled bit in the Port Status Register.

This patch adds new ops for the PHY Energy Detect accesses.

This also allows us to get rid of the MV88E6XXX_FLAG_EEE flag.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Similarly to global1_addr, add a global2_addr member in the info
structure to describe the presence of the Global 2 Registers.

This allows us to get rid of the MV88E6XXX_FLAG_GLOBAL2 flag.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a pot_clear operation to clear the Priority Override Table and wrap
its call into a mv88e6xxx_pot_setup helper.

This allows us to get rid of the MV88E6XXX_FLAG_G2_POT flag.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 88E6390 family clear the Priority Override Table the same way as
88E6352, thus add MV88E6XXX_FLAG_G2_POT to MV88E6XXX_FLAGS_FAMILY_6390.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 88E6185 family only has one 16-bit register to mark the 16 802.1D
reserved multicast addresses in the range of 01:80:C2:00:00:0x as MGMT.

The 88E6352 family also has one 16-bit register to mark the 16 GARP
reserved multicast addresses in the range of 01:80:C2:00:00:2x as MGMT.

Split the existing mv88e6095 prefixed mgmt_rsvd2cpu operation into two
distinct mv88e6185 and mv88e6352 prefixed operations, and wrap its call
into a mv88e6xxx_rsvd2cpu_setup helper.

This allows us to also get rid of the MV88E6XXX_CAP_G2_MGMT_EN_* flags.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Similarly to g1_irqs, add a g2_irqs member to the info structure to
indicates the presence of the Global 2 Interrupt Source and Mask
registers.

At the same time, provide helpers and document the registers since they
differ a bit between 88E6352 and 88E6390 families.

This allows us to get rid of the MV88E6XXX_FLAG_G2_INT flag.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 88E6185 family has no Global 2 Interrupt Source or Mask registers.
Remove the MV88E6XXX_FLAG_G2_INT from MV88E6XXX_FLAGS_FAMILY_6185.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the forgotten capabilities and related flags from previous
cleanups.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some Marvell chips have an Ingress Rate Limit unit. But the command
values slightly differs between models: 88E6352 use 3-bit for operations
while 88E6390 use different 2-bit operations.

This commit kills the IRL flags in favor of a new operation implementing
the "Init all resources to the initial state" operation.

This fixes the operation of 88E6390 family where 0x1000 means Read the
selected resource 0, register 0 on port 16, instead of init all.

A mv88e6xxx_irl_setup helper is added to wrap the operation call.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Prefix and document the Global VTU registers macros and give a clear
16-bit registers representation.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Marvell chips have a Jumbo Mode to set the maximum frame size (MTU).

The mv88e6xxx_ops structure is meant to contain generic functionalities,
no driver logic. Change port_jumbo_config to port_set_jumbo_size setting
the mode from a given maximum size value.

There is no functional changes since we still use 10240 bytes.

At the same time, correctly clear all Jumbo Mode bits before writing.
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All Marvell chips supporting Pause frames limiting use 1-byte value for
input and output.

Old chips have both bytes adjacent in a 16-bit register. New ones have
an indirect table using 8-bit data.

The mv88e6xxx library functions (such as in port.c) must not contain
driver logic, but only generic helpers. This patch changes the
port_pause_config operation for port_pause_limit taking two u8 arguments
for input and output limits. There is no functional changes.
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mv88e6xxx_ops describe functionalities, regardless their locations
(which can be Global1, Global2, or whatever register set.)

Rename the g1_set_cpu_port and g1_set_egress_port ops to set_cpu_port
and set_egress_port. No functional changes.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As for the frame mode, add a mv88e6xxx_egress_mode enumeration instead
of a 16-bit register mask.
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the GLOBAL2_* macros where they belong, in the related global2.h
header.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the GLOBAL_* macros where they belong, in the related global1.h
header. Include it in global2.c which uses GLOBAL_STATUS_IRQ_DEVICE.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the PORT_* macros where they belong, in the related port.h header.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the PHY_* macros where they belong, in the related phy.h header.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mv88e6xxx.h is meant to contains the chip structures and data.
Rename it to chip.h, as for other source/header pairs of the driver.

At the same time, ensure that relative header inclusions are separated
by a newline and sorted alphabetically.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that we use an op for SERDES operations, we don't need a flag for
it. Remove it.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mv88e6390 family has a different SERDES implementation. Refactor
the mv88e6352 code into an ops function, so we can later add the
mv88e6390 code.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The upcoming SERDES support will need to make use of PHY functions. Move
them out into a file of there own. No code changes.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Newer chips such as the 88E6390 have a VTU Page bit in the VTU VID
register to specify a 13th bit for the VID. This can be used to support
8K VLANs.

When dumping the whole VTU, all VID bits must be set to one, including
this VTU Page bit. Add support for VID greater than 4095.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a new vtu_loadpurge operation to the chip info structure to differ
the various implementations of the VTU accesses.

Now that the STU handling is abstracted behind VTU operations, kill the
obsolete MV88E6XXX_FLAG_STU flag.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a new vtu_getnext operation to the chip info structure to differ the
various implementations of the VTU accesses.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

VLAN aware Marvell chips can program 802.1Q VLAN membership as well as
802.1s per VLAN Spanning Tree state using the same 3 VTU Data registers.

Some chips such as 88E6185 use different Data registers offsets for
ports state and membership, and program them in a single operation.

Other chips such as 88E6352 use the same register layout but program
them in distinct operations (an indirect table is used for 802.1s.)

Newer chips such as 88E6390 use the same offsets for both state and
membership in distinct operations, thus require multiple data accesses.

To correctly abstract this, split the "data" structure member of
mv88e6xxx_vtu_entry in two "state" and "member" members, before adding
VTU support for newer chips.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some chips don't have a VLAN Table Unit, most of them do have a 4K
table, some others as the 88E6390 family has a 13th bit for the VID.

Add a new max_vid member to the info structure, used to check the
presence of a VTU as well as the value used to iterate from in VTU
GetNext operations.

This makes the MV88E6XXX_FLAG_VTU obsolete, thus remove it.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Cross-chip Port Based VLAN Table (PVT) is currently initialized with
all ones, allowing any external ports to egress frames on local ports.

This commit implements the PVT access functions and programs the PVT
with all ones for the local switch ports only, instead of using the Init
operation. The current behavior is unchanged for the moment.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Cross-chip Port Based VLAN Table (PVT) supports two indexing modes,
one using 5-bit for device and 4-bit for port, the other using 4-bit for
device and 5-bit for port, configured via the Global 2 Misc register.

Only 4 bits for the source port are needed when interconnecting 88E6xxx
switch devices since they all support less than 16 physical ports. The
full 5 bits are needed when interconnecting a device with 98DXxxx switch
devices since they support more than 16 physical ports.

Add a mv88e6xxx_pvt_setup helper to set the 4-bit port PVT mode, which
will be extended later to also initialize the PVT content.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Not all Marvell switch chips feature a Cross-chip Port VLAN Table (PVT).

Chips with a PVT use the same implementation, so a new mv88e6xxx_ops
member won't be necessary yet. Add a "pvt" boolean member to the
mv88e6xxx_info structure and kill the obsolete MV88E6XXX_FLAGS_PVT flag.

Add a mv88e6xxx_has_pvt helper to wrap future checks of that condition.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is an include loop between netdevice.h, dsa.h, devlink.h because
of NETDEV_ALIGN, making it impossible to use devlink structures in
dsa.h.

Break this loop by taking dsa.h out of netdevice.h, add a forward
declaration of dsa_switch_tree and netdev_set_default_ethtool_ops()
function, which is what netdevice.h requires.

No longer having dsa.h in netdevice.h means the includes in dsa.h no
longer get included. This breaks a few other files which depend on
these includes. Add these directly in the affected file.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a new operation to disable the DA, SA and VTU priority override.

Setting such limit is not likely to be used soon, so provide a
port_disable_pri_override operation directly. This can be changed later
for port_set_pri_override when we'll need it.

Also remove the now obsolete mv88e6xxx_6320_family helper.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a new operation to disable the limiting of learnt MAC addresses.

Setting such limit is not likely to be used soon, so provide a
port_disable_learn_limit operation directly. This can be changed later
for port_set_learn_limit when we'll need it.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Marvell switch ports can be configured to allow or prevent egress of
frames with an unknown unicast or multicast destination address.

Some switch chips such as 88E6095 and 88E6185 have two disjoint bits in
Port Control Register (0x04) bit 2 "Forward Unknown" (for unicast) and
Port Control 2 Register (0x08) bit 6 "Default Forward" (for multicast).

Other chips such as 88E6085, 88E6123, 88E6352, and 88E6390 have a 2-bit
value in Port Control Register (0x04) bits 3:2 "EgressFloods".

The current code does not fully implement the disjoint bits variant and
assigns incorrect ones to some chip models. Fix that with two
implementation references (6185 and 6352 that I currently have) of a
port_set_egress_floods operation (as named in datasheets).

Old chips such as 88E6060 don't have egress flooding mode, so don't
error out if the operation is not provided.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A switch port mode is defined by the association of its egress mode, its
frame mode and if supported or required, the ether type value.

Pack all this in a mv88e6xxx_set_port_mode function and provide helpers
for the Normal Network mode, the DSA mode, and the Ether Type DSA mode,
as well as an helper to setup a port's mode depending on its nature.

Define PORT_ETH_TYPE_DEFAULT for the 0x9100 reset value of port E Type.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Not all Marvell switch chips support port trunking, which is embedded in
the port vector data for ATU operations.

Rename the portv_trunkid member of the mv88e6xxx_atu_entry structure to
portvec to be more concise and consistent with the different chips.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a fresh documented implementation of the ATU Move operation, and use
it to replace the current ATU Remove operation.

Note that not all Marvell switch chip support the ATU Move operation.
For those supporting it, the number of bits used to mask the destination
port may vary. 6352 and such use 4-bit, while 6390 use 5-bit. Thus add a
new atu_move_port_mask member in the info structure to describe the
presence and variant of ATU Move operation.

Note that the ATU Move operation is not documented in the 6185 datasheet
but the chip does support the operation.

All remaining _mv88e6xxx_atu_* functions are now unused as well as the
MV88E6XXX_FLAG_G1_ATU_FID flag, thus remove them.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All interconnectable Marvell switch chips have an ATU Learn2All feature
which allows newly learnt addresses to be spanned on ports marked as
"Message Port".

This commit configures the DSA ports as Message Port. Note that this has
no effect until the Learn2All feature is enabled.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>