MIPI-CSI has internal memory mapped buffers for the frame embedded
(non-image) data. There are two buffers, for even and odd frames which
need to be saved after an interrupt is raised. The packet data buffers
size is 4 KiB and there is no status register in the hardware where the
actual non-image data size can be read from. Hence the driver copies
whole packet data buffer into a buffer provided by the FIMC driver.
This will form a separate plane in the user buffer.
When FIMC DMA engine is stopped by the driver due the to user space
not keeping up with buffer de-queuing the MIPI-CSIS will still run,
however it must discard data which is not captured by FIMC. Which
frames are actually capture by MIPI-CSIS is determined by means of
the s_tx_buffer subdev callback. When it is not called after a single
embedded data frame has been captured and copied and before next
embedded data frame interrupt occurrs, subsequent embedded data frames
will be dropped.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adds definition of the Samsung S5C73M3 camera specific
image format. V4L2_PIX_FMT_S5C_UYVY_JPG is a two-planar format,
the  first plane contains interleaved UYVY and JPEG data followed
by meta-data. The second plane contains additional meta-data needed
for extracting JPEG and UYVY data stream from the first plane.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adds media bus pixel code for the interleaved JPEG/UYVY
image format used by S5C73MX Samsung cameras. This interleaved image
data is transferred on MIPI-CSI2 bus as User Defined Byte-based Data.
It also defines an experimental vendor and device specific media bus
formats section and adds related DocBook documentation.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add subdev callbacks for setting up parameters of the frame on media bus
that are not exposed to user space directly. This is just an initial,
mostly stub implementation. struct v4l2_mbus_frame_desc is intended
to be extended with sub-structures specific to a particular hardware media
bus. For now these new callbacks are used only to query or specify maximum
size of a compressed or hybrid (container) media bus frame in octets.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The s_rx_buffer callback allows the host to set buffer for a data being
received by the subdev, e.g. non-image frame (meta) data. This callback
can be implemented by subdevice like a MIPI CSI2 receiver, allowing the
host driver to gather additional data into frame buffer passed to user
space.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

drivers/media/platform/s5p-fimc/fimc-m2m.c:561:2: warning: passing argument 2 of 'fimc_m2m_try_crop' discards 'const' qualifier from pointer target type [enabled by default]
drivers/media/platform/s5p-fimc/fimc-m2m.c:502:12: note: expected 'struct v4l2_crop *' but argument is of type 'const struct v4l2_crop *'
This is fall-out from this commit:
commit 4f996594
Author: Hans Verkuil <hans.verkuil@cisco.com>
    [media] v4l2: make vidioc_s_crop const
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

drivers/media/platform/s5p-g2d/g2d.c:535:2: warning: passing argument 3 of 'vidioc_try_crop' discards 'const' qualifier from pointer target type [enabled by default]
drivers/media/platform/s5p-g2d/g2d.c:510:12: note: expected 'struct v4l2_crop *' but argument is of type 'const struct v4l2_crop *'
This is fall-out from this commit:
commit 4f996594
Author: Hans Verkuil <hans.verkuil@cisco.com>
    [media] v4l2: make vidioc_s_crop const
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Convert clk_enable/clk_disable to clk_prepare_enable/clk_disable_unprepare
calls as required by common clock framework.
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adds a module-device-table-entry to the
technisat-usb2-driver which will help udev to on-demand load the
driver. This was obviously forgotten during initial commit.
Signed-off-by: NPatrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch replaces V4L2_OUT_CAP_CUSTOM_TIMINGS macro with
V4L2_OUT_CAP_DV_TIMINGS. As V4L2_OUT_CAP_CUSTOM_TIMINGS is being phased
out.
Signed-off-by: NLad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: NManjunath Hadli <manjunath.hadli@ti.com>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

recent patch with commit id 4f996594
which makes vidioc_s_crop const, was causing a following build warning,
vpbe_display.c: In function 'vpbe_display_s_crop':
vpbe_display.c:640: warning: initialization discards qualifiers from pointer target type
This patch fixes the above build warning.
Signed-off-by: NLad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: NManjunath Hadli <manjunath.hadli@ti.com>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

add filter settings for high def modes like 1080i,
1080p,720p and others and implementing dv_timings.
Signed-off-by: NManjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: NLad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch replaces the preset API by the timings API, and
appropriate changes in board file.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NLad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: NManjunath Hadli <manjunath.hadli@ti.com>
Acked-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

As spotted by Dan Carpenter <dan.carpenter@oracle.com> (thanks!), we have
improperly used an unsigned variable in a calculation that may result in a
negative number. This may cause an unintended underflow if the interface
frequency of the tuner is > approx. 40MHz.
This patch should resolve the issue, following an approach similar to what is
used in af9013.c.

[crope@iki.fi: add Reported-by]
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NHans-Frieder Vogt <hfvogt@gmx.net>
Reviewed-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

recent patch with commit id 4f996594
which makes vidioc_s_crop const, was causing a following build error.
vpfe_capture.c: In function 'vpfe_s_crop':
vpfe_capture.c:1695: error: assignment of read-only location '*crop'
vpfe_capture.c:1706: warning: passing argument 1 of
'ccdc_dev->hw_ops.set_image_window' discards qualifiers from pointer target type
vpfe_capture.c:1706: note: expected 'struct v4l2_rect *' but argument is of
type 'const struct v4l2_rect *'
make[4]: *** [drivers/media/platform/davinci/vpfe_capture.o] Error 1
Signed-off-by: NLad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: NManjunath Hadli <manjunath.hadli@ti.com>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

As em28xx-dvb will always be initialized asynchronously, there's
no need anymore for a separate thread to load the DRX-K firmware.

Fixes a known regression with kernel 3.6 with tda18271 driver
and asynchronous DRX-K firmware load.

Antti tested it with the following hardware:
        Hauppauge WinTV HVR 930C
        MaxMedia UB425-TC
        PCTV QuatroStick nano (520e)
Tested-by: NAntti Palosaari <crope@iki.fi>
Cc: stable@kernel.org #	for Kernel 3.6 - please note that driver location has changed
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Due to udev-182, the firmware load was changed to be async, as
otherwise udev would give up of loading a firmware.

Add an option to return to the previous behaviour, async firmware
loads cause failures with the tda18271 driver.

Antti tested it with the following hardware:
        Hauppauge WinTV HVR 930C
        MaxMedia UB425-TC
        PCTV QuatroStick nano (520e)
Tested-by: NAntti Palosaari <crope@iki.fi>
Cc: stable@kernel.org #	for Kernel 3.6 - please note that driver location has changed
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

em28xx-dvb, em28xx-alsa and em28xx-ir are typically initialized
asyncrhronously. The exception for it is when those modules
are loaded before em28xx (or before an em28xx card insertion) or
when they're built in.

Make the extentions to always load asynchronously. That allows
having all DVB firmwares loaded synchronously with udev-182.

Antti tested it with the following hardware:
	Hauppauge WinTV HVR 930C
	MaxMedia UB425-TC
	PCTV QuatroStick nano (520e)
Tested-by: NAntti Palosaari <crope@iki.fi>
Cc: stable@kernel.org # for Kernel 3.6 - please note that driver location has changed
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Until now, if there is a read error in tda18271_get_id, the driver
reports "Unknown device..."  Instead, check the return value of
tda18271_read_regs and display the appropriate error message.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

if the configuration option 'delay_cal' is set, delay both IR & RF
calibration until init() is called.
both module option 'cal' or configuration option 'rf_cal_on_startup'
will override this delay. it makes no sense to mix 'delay_cal' with
'rf_cal_on_startup' as these options conflict with each other.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The mixer video node supports only multi-planar API so the driver
should not be setting V4L2_CAP_VIDEO_OUTPUT flags. Fix this and
also switch to device_caps. Additionally fix the VIDIOC_ENUM_FMT
ioctl handler which now works for V4L2_BUF_TYPE_CAPTURE, rather
than expected V4L2_BUF_TYPE_CAPTURE_MPLANE.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

return statement was wrongly placed before a code that needs to be
executed. Moved the return statement to the end of the function.
Tested suspend/resume on SMDK4412 board using 3.5-rc6 kernel.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Acked-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Fixes the following warnings:
drivers/media/platform/exynos-gsc/gsc-core.c:313:5: warning:
symbol 'get_plane_info' was not declared. Should it be static?
drivers/media/platform/exynos-gsc/gsc-core.c:746:28: warning:
symbol 'gsc_ctrl_ops' was not declared. Should it be static?
drivers/media/platform/exynos-gsc/gsc-m2m.c:102:5: warning:
symbol 'gsc_fill_addr' was not declared. Should it be static?
drivers/media/platform/exynos-gsc/gsc-m2m.c:252:16: warning:
symbol 'gsc_m2m_qops' was not declared. Should it be static?
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

version.h is not needed for these files.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Fixes a typo in a conditional evaluation.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

When mdev is NULL, the error print statement will try to dereference
the NULL pointer.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Acked-by: NTomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Make sure __s5k6aa_get_crop_rect() always returns valid pointer,
as it is assumed at the callers.
crop->which is already validated when subdev set_crop and get_crop
callbacks are called from within the v4l2-core. If it ever happens
the crop operations are called directly for some reason in kernel
space, with incorrect crop->which argument, just log it with WARN
and return reference to the TRY crop.
Reported-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

All code setting/clearing working context bits has been moved
to separate functions. set_bit/clear_bit have been replaced by
non-atomic variants - variable is already guarded by spin_lock.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

s5p-mfc encoder after receiving V4L2_ENC_CMD_STOP command
will instruct MFC device to release all encoded frames.
After dequeuing last encoded frame driver will generate
V4L2_EVENT_EOS event.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Without the locking the driver's data could get corrupted when the subdev
is accessed from user space and from host driver by multiple processes.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Since all host drivers using this subdev are already using
the control framework these compatibility ops can be removed.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Use a copy of sensor platform data structure, rather than referencing
external platform data from the driver. This allows to fill the local
copy with values parsed from device tree when needed.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>