When link is lost on a card which uses internal PHY for 10 Mbit speeds,
restart autonegotiation to allow switching between 10 and 100 Mbps speeds.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Olicom OC-2325 and OC-2326 cards have the MAC address byte-swapped in EEPROM.
Byte-swap the MAC address if it's located at offset 0xF8.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add basic ethtool support to tlan driver:
 - driver info  - link detect (this allows NetworkManager to detect carrier)
 - EEPROM read
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable old link monitoring code and modify it:
 - control LINK LED
 - use separate timer so it does not interfere with ACT LED

Tested with Olicom OC-2326.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Olicom OC-2325 and OC-2326 ethernet cards have an activity LED but it does not
work with tlan driver as it's not enabled. Enable it.
Tested with OC-2326.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

kasprintf combines kmalloc and sprintf, and takes care of the size
calculation itself.

The semantic patch that makes this change is as follows:

// <smpl>
@@
expression a,flag;
expression list args;
statement S;
@@

  a =
-  \(kmalloc\|kzalloc\)(...,flag)
+  kasprintf(flag,args)
  <... when != a
  if (a == NULL || ...) S
  ...>
- sprintf(a,args);
// </smpl>
Signed-off-by: NHimangi Saraogi <himangi774@gmail.com>
Acked-by: NJulia Lawall <julia.lawall@lip6.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Stefan Sørensen says:

====================
Add ptp vlan support

This patch series adds functionality for running ptp/ieee1588 over vlan.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This allows applications to enable hardware timestamping without being aware
of it being a vlan device and figuring out the real device.
Signed-off-by: NStefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This extends the ptp bpf to also match ptp over ip over vlan packets. The ptp
classes are changed to orthogonal bitfields representing version, transport
and vlan values to simplify matching.
Signed-off-by: NStefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace two switch statements enumerating all valid ptp classes with an if
statement matching for not PTP_CLASS_NONE.
Signed-off-by: NStefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
Misc SCTP updates

Daniel Borkmann (2):
  net: sctp: improve timer slack calculation for transport HBs
  net: sctp: only warn in proc_sctp_do_alpha_beta if write
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>

Only warn if the value is written to alpha or beta. We don't care
emitting a one-time warning when only reading it.
Reported-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Reviewed-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RFC4960, section 8.3 says:

  On an idle destination address that is allowed to heartbeat,
  it is recommended that a HEARTBEAT chunk is sent once per RTO
  of that destination address plus the protocol parameter
  'HB.interval', with jittering of +/- 50% of the RTO value,
  and exponential backoff of the RTO if the previous HEARTBEAT
  is unanswered.

Currently, we calculate jitter via sctp_jitter() function first,
and then add its result to the current RTO for the new timeout:

  TMO = RTO + (RAND() % RTO) - (RTO / 2)
              `------------------------^-=> sctp_jitter()

Instead, we can just simplify all this by directly calculating:

  TMO = (RTO / 2) + (RAND() % RTO)

With the help of prandom_u32_max(), we don't need to open code
our own global PRNG, but can instead just make use of the per
CPU implementation of prandom with better quality numbers. Also,
we can now spare us the conditional for divide by zero check
since no div or mod operation needs to be used. Note that
prandom_u32_max() won't emit the same result as a mod operation,
but we really don't care here as we only want to have a random
number scaled into RTO interval.

Note, exponential RTO backoff is handeled elsewhere, namely in
sctp_do_8_2_transport_strike().
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sathya Perla says:

====================
be2net: patch set

v2 change: merged 2 lines into one in patch 4

Patch 1 refactors be_cmd_get_profile_config() routine to reduce
code duplication by using the be_cmd_notify_wait() routine, instead
of using a separate variant of the code for MBOX and MCCQ.

Patch 2 introduces the required FW-cmd code in the PF to query
RSS support on a VF. This is in preparation for patch 3.

Patch 3 adds support for the PF driver to re-configure the resource
distribution in FW based on the number of VFs enabled by the user. When
the user is not interested in enabling VFs, all resources of a port are
set-aside for the PF. If less than maximum number of VFs are enabled, then
each VF gets a better share of the resources and can now enable RSS (if
the interface supports it.)

Patch 4 is a minor fix to re-enable HW vlan filtering as soon as the number
of vlans programmed is within the HW limit.

Please consider applying to net-next tree. Thanks!
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While adding vlans, when the HW limit of vlan filters is reached, the
driver enables vlan promiscuous mode.
Similarily, while removing vlans, the driver must re-enable HW filtering
as soon as the number of vlan filters is within the HW limit.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If SR-IOV is enabled in the adapter, the FW distributes queue resources
evenly across the PF and it's VFs. If the user is not interested in enabling
VFs, the queues set aside for VFs are wasted.
This patch adds support for the PF driver to re-configure the resource
distribution in FW based on the number of VFs enabled by the user.
This also allows for supporting RSS queues on VFs, when less number of VFs
are enabled per PF. When maximum number of VFs are enabled, each VF typically
gets only one RXQ.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PF driver must query the FW for VF's interface capabilities
to know if the VF is RSS capable or not.
This patch is in preparation for enabling RSS on VFs on Skyhawk-R.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix be_cmd_get_profile_cmd() to use be_cmd_notify_wait() routine,
which uses MBOX if MCCQ has not been created. Doing this reduces
code duplication; we don't need the _mbox/_mccq() variants anymore.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix checkpatch warning:
WARNING: kfree(NULL) is safe this check is probably not required

Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: netdev@vger.kernel.org
Signed-off-by: NFabian Frederick <fabf@skynet.be>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since consume_skb() (and hence dev_kfree_skb() macro) checks the passed pointer
for NULL, there's no need to check for NULL before invoking dev_kfree_skb().
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NPrashant Sreedharan <prashant@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Harish Patil says:

====================
qlcnic: Enhance Tx timeout debug data collection.

The following set of patches are for enhancing Tx timeout debug collection

- Collect a firmware dump on first Tx timeout if netif_msg_tx_err() is set
- Log Receive and Status ring info on Tx timeout, in addition to Tx ring info
- Log additional Tx ring info if netif_msg_tx_err() is set
- Update driver version to 5.3.61

Please apply this series to net-next.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NHarish Patil <harish.patil@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Collect a firmware dump on first Tx timeout if netif_msg_tx_err() is set
- Log Receive and Status ring info on Tx timeout, in addition to Tx ring info
- Log additional Tx ring info if netif_msg_tx_err() is set
Signed-off-by: NHarish Patil <harish.patil@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

based on checkpatch:
"debugfs_remove_recursive(NULL) is safe this check is probably not required"

Cc: Dmitry Tarnyagin <dmitry.tarnyagin@lockless.no>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: NFabian Frederick <fabf@skynet.be>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c: remove unnecessary null test before debugfs_remove_recursive

Fix checkpatch warning:
"WARNING: debugfs_remove_recursive(NULL) is safe this check is probably not required"

Cc: Hariprasad S <hariprasad@chelsio.com>
Cc: netdev@vger.kernel.org
Signed-off-by: NFabian Frederick <fabf@skynet.be>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When an UDP application switches from AF_INET to AF_INET6 sockets, we
have a small performance degradation for IPv4 communications because of
extra cache line misses to access ipv6only information.

This can also be noticed for TCP listeners, as ipv6_only_sock() is also
used from __inet_lookup_listener()->compute_score()

This is magnified when SO_REUSEPORT is used.

Move ipv6only into struct sock_common so that it is available at
no extra cost in lookups.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2014-07-01

This series contains updates to i40e, i40evf, igb and ixgbe.

Shannon adds the Base Address High and Low to the admin queue structure
to simplify the logic in the configuration routines.  Also adds code to
clear all queues and interrupts to help clean up after a PXE or other
early boot activity.

Kevin fixes mask assignment value since -1 cannot be used for unsigned
integer types.

Mitch fixes an issue where in some circumstances the reply from the PF
would come back before we were able to properly modify the admin queue
pending and required flags.  This would mess up the flags and put the
driver in an indeterminate state, so fix this by simply setting the flags
before sending the request to the admin queue.  Also changes the branding
string for i40evf to reduce confusion and to match up with our other
marketing materials.

Kamil adds a new variable defining admin send queue (ASQ) command write
back timeout to allow for dynamic modification of this timeout.

Anjali fix a bug in the flow director filter replay logic, so that we
call a replay after a sideband reset correctly.

Jesse adds code to initialize all members of the context descriptor to
prevent possible stale data.

Christopher fixes i40e to prevent writing to reserved bits, since the
queue index is only 0-127.

Jacob removes the unneeded header export.h from the i40e PTP code.
Fixes ixgbe PTP code where the PPS signal was not correct, as it
generates a one half HZ clock signal, it only generates one level
change per second.  To generate a full clock, we need two level changes
per second.

Todd provides a fix for igb to bring up link when the PHY has powered
up, which was reported by Jeff Westfahl.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This limitation maybe had some reason in the past, but now there is not
one -> removing this.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Acked-by: NVeaceslav Falico <vfalico@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hariprasad Shenai says:

====================
cxgb4: Fix for PCI passthrough and some Misc. fixes

This patch series fixes probe failure in VM when PF is exposed through PCI
Passthrough. Adds support to use firmware interface to get BAR0 value.
Replace the backdoor mechanism to access the HW memory with PCIe Window method
which fixes memory I/O. Also adds device ID of few more adapters for cxgb4 and
cxgb4vf driver.

The patches series is created against 'net-next' tree.
And includes patches on cxgb4, cxgb4vf and iw_cxgb4 driver.

Since this patch-series contains mainly cxgb4 related changes, we would like to
request this patch series to get merged via David Miller's 'net-next' tree.

We have included all the maintainers of respective drivers. Kindly review the
change and let us know in case of any review comments.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rip out a bunch of redundant PCI-E Memory Window Read/Write routines,
collapse the more general purpose routines into a single routine
thereby eliminating the need for a large stack frame (and extra data
copying) in the outer routine, change everything to use the improved
routine t4_memory_rw.

Based on origninal work by Casey Leedom <leedom@chelsio.com> and
Steve Wise <swise@opengridcomputing.com>
Signed-off-by: NCasey Leedom <leedom@chelsio.com>
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the firmware interface to get the BAR0 value since we really don't want
to use the PCI-E Configuration Space Backdoor access which is owned by the
firmware.

Set up PCI-E Memory Window registers using the true values programmed into
BAR registers.  When the PF4 "Master Function" is exported to a Virtual
Machine, the values returned by pci_resource_start() will be for the
synthetic PCI-E Configuration Space and not the real addresses. But we need
to program the PCI-E Memory Window address decoders with the real addresses
that we're going to be using in order to have accesses through the Memory
Windows work.

Based on origninal work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: NCasey Leedom <leedom@chelsio.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change logic which determines our Physical Function at PCI Probe time.
Now we read the PL_WHOAMI register and get the Physical Function.

Pass Physical Function to Upper Layer Drivers in lld_info structure in the
new field "pf" added to lld_info.  This is useful for the cases where the
PF, say PF4, is attached to a Virtual Machine via some form of "PCI
Pass Through" technology and the PCI Function shows up as PF0 in the VM.

Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: NCasey Leedom <leedom@chelsio.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Stefan Sørensen says:

====================
dp83640: Increase support perout pins

This patch series increases the number of periodic output pins supported
on the dp83640 to 7, and allows for reprogramming the calibration pin.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ptp pin function programming does not allow calibration pin to change
function. This is problematic on hardware that uses the default calibration
pin for other purposes.

Removing this limitation does not impact calibration if userspace does not
reprogram the calibration pin.
Signed-off-by: NStefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For consistency, use the ptp_find_pin function to get the calibration pin,
not gpio_tab.
Signed-off-by: NStefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This constraints the pin assignment to not allow the calibration function to
be reassigned and only allow reassigning the calibratin pin if only one phy is
connected.
Signed-off-by: NStefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch increases the number of supported periodic output pins from
1 to 7. The last pin is reserved for sync.
Signed-off-by: NStefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>