The driver waits for command completion event while cleanup of task
within the frwd lock and back locks. The frwd lock was still held
which caused the call trace while issuing a device reset.
Release the frwd lock along with the back lock
to avoid waiting in the lock context.
Signed-off-by: NNilesh Javali <nilesh.javali@qlogic.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Fix the firmware assert, during target logout in
case driver received FIN from target before waiting for
asyncronous response.
Signed-off-by: NTej Parkash <tej.parkash@qlogic.com>
Signed-off-by: NNilesh Javali <nilesh.javali@qlogic.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Newer revisions of QUALCOMM Technologies UFS host controller may not
advertise the correct version information in UFS HCI VER register.
To handle this, enable UFSHCD_QUIRK_BROKEN_UFS_HCI_VERSION to let
UFS standard host controller driver call into vendor specific
operation to get right UFS HCI VER register value.
Signed-off-by: NYaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Some host controller hardware controllers may not advertise correct
version in UFS HCI VER register. To workaround this, add new quirk
and call the host controller hardware vendor specific callback to
get the correct UFS HCI version register value.
Signed-off-by: NYaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Current version of host controller on QUALCOMM Technologies requires
this quirk to be enabled, as DME commands to device must be sent
only in AUTO mode (SLOW AUTO or FAST AUTO).
Signed-off-by: NYaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Some UFS host controllers may only allow accessing the peer DME attribute
in AUTO mode (FAST AUTO or SLOW AUTO) hence we had added a quirk for
switching to AUTO power mode before accessing the peer DME attribute.
Signed-off-by: NYaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

With the G3 UFS devices, changing gear into HS is failing in UFS host
controllers of version 0x2.
The quirk solves the problem of changing gear into HS by enabling
the attribute that specifies whether or not the inbound Link supports
unterminated line in HS mode.
Signed-off-by: NYaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

The attribute PA_RXHSUNTERMCAP specifies whether or not the
inbound Link supports unterminated line in HS mode. enabling this
attribute to 1 fixes moving to HS gear.
Signed-off-by: NYaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

LCC (Line Control Command) are being used for communication between
UFS host and UFS device. But UFS host controller on QUALCOMM
Technologies have an issue with issuing the LCC commands to
UFS device and hence this quirk is enabled in order to to disable
LCC from the host side.
Signed-off-by: NYaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

LCC (Line Control Command) are being used for communication between
UFS host and UFS device.
New commercial UFS devices don't have the issues with LCC processing
but UFS host controller might still have the issue with LCC processing,
hence, added a routine to disable TX LCC on the device.
Signed-off-by: NYaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Current versions of UFS host controllers on QUALCOMM Technologies
have interrupt aggregation logic broken.
Interrupt aggregation may not work if both threshold count and timeout
is enabled. Hence disable interrupt aggregation by enabling
UFSHCD_QUIRK_BROKEN_INTR_AGGR quirk until its fixed in the newer
UFS host controller revisions.
Signed-off-by: NYaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

UFS HCI (Host Controller Interface) allows the transfer requests
interrupts to be aggregated to generate the single interrupt but
this can impact the performance. Hence introduce the capability which
gives choice to use the interrupt aggregation capability or not.
By default interrupt aggregation capability is kept disabled.

This change also introduces a quirk for broken interrupt aggregation
feature, as in some UFS controllers, this feature may not work.
Signed-off-by: NYaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Increase the default init stage change timeout from 15 seconds to 30 seconds.
This resolves issues we have seen with some adapters not transitioning
to the first init stage within 15 seconds, which results in adapter
initialization failures.

Cc: <stable@vger.kernel.org>
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

This patch implements tape statistics in the st module via
sysfs. Current no statistics are available for tape I/O and there
is no easy way to reuse the block layer statistics for tape
as tape is a character device and does not have perform I/O in
sector sized chunks (the size of the data written to tape
can change). For tapes we also need extra stats related to
things like tape movement (via other I/O).

There have been multiple end users requesting statistics
including AT&T (and some HP customers who have not given
permission to be named). It is impossible for them
to investigate any issues related to tape performance
in a non-invasive way.

[jejb: eliminate PRId64]
Signed-off-by: NShane Seymour <shane.seymour@hp.com>
Tested-by: NShane Seymour <shane.seymour@hp.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Only include SCSI initiator header files in target code that needs
these header files, namely the SCSI pass-through code and the tcm_loop
driver. Change SCSI_SENSE_BUFFERSIZE into TRANSPORT_SENSE_BUFFER in
target code because the former is intended for initiator code and the
latter for target code. With this patch the only initiator include
directives in target code that remain are as follows:

$ git grep -nHE 'include .scsi/(scsi.h|scsi_host.h|scsi_device.h|scsi_cmnd.h)' drivers/target drivers/infiniband/ulp/{isert,srpt} drivers/usb/gadget/legacy/tcm_*.[ch] drivers/{vhost,xen} include/{target,trace/events/target.h}
drivers/target/loopback/tcm_loop.c:29:#include <scsi/scsi.h>
drivers/target/loopback/tcm_loop.c:31:#include <scsi/scsi_host.h>
drivers/target/loopback/tcm_loop.c:32:#include <scsi/scsi_device.h>
drivers/target/loopback/tcm_loop.c:33:#include <scsi/scsi_cmnd.h>
drivers/target/target_core_pscsi.c:39:#include <scsi/scsi_device.h>
drivers/target/target_core_pscsi.c:40:#include <scsi/scsi_host.h>
drivers/xen/xen-scsiback.c:52:#include <scsi/scsi_host.h> /* SG_ALL */
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Correct the comment above the definition of TCM_MAX_COMMAND_SIZE.
A quote from Christoph:

    There aren't any legacy issues, we just decided to handle >
    16 byte CDBs in the slow path.
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Move the functions that are used by both the initiator and target
subsystems into scsi_common.c/.h. This change will allow to remove
the initiator SCSI header include directives from most SCSI target
source files in a later patch.
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Move the constants that are used by both initiator and target
drivers into the new header file <scsi/scsi_proto.h>. This change
will allow to remove the initiator SCSI header include directives
from most SCSI target source files in a later patch.
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

megaraid_sas : Modify return value of megasas_issue_blocked_cmd() and wait_and_poll() to consider command status returned by firmware

This patch is rebased on top of recently sent 18 patches(submitted by me) for
megaraid_sas driver.

Change the return value of wait_and_poll() and megsas_issue_blocked_cmd()
based on MFI_STAT returned by firmware for that command. Earlier driver always
send return type based on command completion (but never check MFI_STAT_OK for
that command), so even if command is failed by firmware still driver will
return SUCCESS status from these functions wait_and_poll() and
megsas_issue_blocked_cmd() and if caller of these functions does not check
command status (MFI_STAT), then it may endup using invalid data returned in
DMA buffers(one of the example is megasas_ld_list_query DCMD). Best thing to
avoid this type of issue is do error handling and set proper return type from
caller function wait_and_poll() and megsas_issue_blocked_cmd().

The change proposed in this patch will fix the regression introduced in patch-
"90dc9d98 megaraid_sas : MFI MPT linked list corruption fix" inside function
megasas_ld_list_query().  Prior to this MFI MPT linked list corruption fix
patch, megasas_ld_list_query() function used to check DCMD status(returned by
firmware) but with this linked list corruption fix patch, DCMD status will not
be checked inside function megasas_ld_list_query() and introduced this issue
of wrong data being used by function megasas_ld_list_query().

Cc: <stable@vger.kernel.org>
Signed-off-by: NKashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

'0' is now used as the default cmd_per_lun value,
so there's no need to explicitly set it to '1' in the
host template.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

update driver version
Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Reviewed-by: NKevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NHannes Reinecke <hare@Suse.de>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

add in support for latest PMC controller
Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NHannes Reinecke <hare@Suse.de>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Synchronize completion the reset with completion of outstanding commands

Extending the newly-added synchronous abort functionality,
now also synchronize resets with the completion of outstanding commands.
Rename the wait queue to reflect the fact that it's being used for both
types of waits.  Also, don't complete commands which are terminated
due to a reset operation.

fix for controller lockup during reset
Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Reviewed-by: NKevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NHannes Reinecke <hare@Suse.de>
Signed-off-by: NWebb Scales <webbnh@hp.com>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

If hpsa_wait_for_board_state fails, hpsa_kdump_soft_reset
should propagate its return value (e.g., -ENODEV) rather
than just returning -1.
Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Reviewed-by: NKevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: NHannes Reinecke <hare@Suse.de>
Signed-off-by: NRobert Elliott <elliott@hp.com>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Rather than numbering the hpsa controllers with an
incrementing 0..n value (e.g., that shows up in
/proc/interrupts), use the scsi midlayer
host_no (e.g. matching /sys/class/scsi_host/hostNN).
Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Reviewed-by: NKevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NHannes Reinecke <hare@Suse.de>
Signed-off-by: NRobert Elliott <elliott@hp.com>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Rework slave allocation:
  - separate the tagging support setup from the hostdata setup
  - make the hostdata setup act consistently when the lookup fails
  - make the hostdata setup act consistently when the device is not added
  - set up the queue depth consistently across these scenarios
  - if the block layer mq support is not available, explicitly enable and
    activate the SCSI layer tcq support (and do this at allocation-time so
    that the tags will be available for INQUIRY commands)

Tweak slave configuration so that devices which are masked are also
not attached.
Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Reviewed-by: NKevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NHannes Reinecke <hare@Suse.de>
Signed-off-by: NWebb Scales <webbnh@hp.com>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Add the interrupt number to the interrupt names that
appear in /proc/interrupts, so they are unique

Also, delete the IRQ and DAC prints.  Other parts of the kernel
already print the IRQ assignments, and dual-address-cycle support
has not been interesting since the parallel PCI bus went from
32 to 64 bits wide.
Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Reviewed-by: NKevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NHannes Reinecke <hare@Suse.de>
Signed-off-by: NRobert Elliott <elliott@hp.com>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Don't create the resubmit workqueue in hpsa_init_one until everything else
is ready to use, so everything can be freed in reverse order of when they
were allocated without risking freeing things while workqueue items are
still active.

Destroy the workqueue in the right order in
hpsa_undo_allocations_after_kdump_soft_reset too.
Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Reviewed-by: NKevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NHannes Reinecke <hare@Suse.de>
Signed-off-by: NRobert Elliott <elliott@hp.com>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

If registering the special interrupt handlers in hpsa_init_one
before a soft reset fails, the error exit needs to deallocate
everything that was allocated before.
Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Reviewed-by: NKevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NHannes Reinecke <hare@Suse.de>
Signed-off-by: NRobert Elliott <elliott@hp.com>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

In hpsa_undo_allocations_after_kdump_soft_reset,
the things allocated in hpsa_init_one step 2 -
h->resubmit_wq and h->lockup_detected  need to
be freed, in the right order.
Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Reviewed-by: NKevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NHannes Reinecke <hare@Suse.de>
Signed-off-by: NRobert Elliott <elliott@hp.com>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

If try_soft_reset fails to re-allocate irqs, the error exit
starts with free_irq calls, which generate kernel WARN
messages since they were already freed a few lines earlier.

Jump to the next exit label to skip the free_irq calls.
Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Reviewed-by: NKevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NHannes Reinecke <hare@Suse.de>
Signed-off-by: NRobert Elliott <elliott@hp.com>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Despite the fact that PCI devices are enabled in this order:
    1. pci_enable_device
    2. pci_request_regions

    Documentation/PCI/pci.txt specifies that they be undone
    in this order
    1. pci_disable_device
    2. pci_release_regions

    Tested by injecting error in the call to pci_enable_device
    in hpsa_init_one -> hpsa_pci_init:
    [    9.095001] hpsa 0000:04:00.0: failed to enable PCI device
    [    9.095005] hpsa: probe of 0000:04:00.0 failed with error -22
    (-22 is -EINVAL)
    and then in the call pci_request_regions:
    [    9.178623] hpsa 0000:04:00.0: failed to obtain PCI resources
    [    9.178671] hpsa: probe of 0000:04:00.0 failed with error -16
    (-16 is -EBUSY)

    and then by adding
        reset_devices
    to the kernel command line and inject errors into the two
    calls to pci_enable_device and the call to pci_request_regions
    in hpsa_init_one -> hpsa_init_reset_devices.

    (inject on 6th call, 1st to hpsa2)
    [   62.413750] hpsa 0000:04:00.0: Failed to enable PCI device

    (inject on 7th call, 2nd to hpsa2)
    [   62.807571] hpsa 0000:04:00.0: failed to enable device.

    (inject on 8th call, 3rd to hpsa2)
    [   62.697198] hpsa 0000:04:00.0: failed to obtain PCI resources
    [   62.697234] hpsa: probe of 0000:04:00.0 failed with error -16

    The reset_devices path calls return -ENODEV on failure
    rather than passing the result, which apparently doesn't
    cause the pci driver to print anything.
Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Reviewed-by: NKevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NHannes Reinecke <hare@Suse.de>
Signed-off-by: NRobert Elliott <elliott@hp.com>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Divide the loop in hpsa_scatter_gather() into two, one for the initial SG list
and a second one for the chained list, if any.  This allows the conditional
check which resets the indicies for the chained list to be performed outside
the loop instead of being done on every iteration inside the loop.
Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Reviewed-by: NKevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NHannes Reinecke <hare@Suse.de>
Signed-off-by: NWebb Scales <webbnh@hp.com>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Factor out the code which sends the TEST_UNIT_READY from
wait_for_device_to_become_ready() into its own function.

Move the code which waits for the TEST_UNIT_READY from
wait_for_device_to_become_ready() into its own function.

If a logical drive has failed, resetting it will ensure
outstanding commands are completed, but polling it with
TURs after the reset will not work because the TURs will
never report good status.  So successful TUR should not
be a condition of success for the device reset error
handler.
Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Reviewed-by: NKevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NHannes Reinecke <hare@Suse.de>
Signed-off-by: NWebb Scales <webbnh@hp.com>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Don't return from the abort request until the target command is complete.
Mark outstanding commands which have a pending abort, and do not send them
to the host if we can avoid it.

If the current command has been aborted, do not call the SCSI command
completion routine from the I/O path: when the abort returns successfully,
the SCSI mid-layer will handle the completion implicitly.

The following race was possible in theory.

1. LLD is requested to abort a scsi command
2. scsi command completes
3. The struct CommandList associated with 2 is made available.
4. new io request to LLD to another LUN re-uses struct CommandList
5. abort handler follows scsi_cmnd->host_scribble and
   finds struct CommandList and tries to aborts it.

Now we have aborted the wrong command.

Fix by resetting the scsi_cmd field of struct CommandList
upon completion and making the abort handler check that
the scsi_cmd pointer in the CommadList struct matches the
scsi_cmnd that it has been asked to abort.
Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Reviewed-by: NKevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NHannes Reinecke <hare@Suse.de>
Signed-off-by: NWebb Scales <webbnh@hp.com>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

cleanup command completions
Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Reviewed-by: NKevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NHannes Reinecke <hare@Suse.de>
Signed-off-by: NWebb Scales <webbnh@hp.com>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

add support for tmf when in ioaccel2 mode
Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Reviewed-by: NKevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NHannes Reinecke <hare@Suse.de>
Signed-off-by: NJoe Handzik <joseph.t.handzik@hp.com>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

The SCSI midlayer already prints more detail about completions,
and has logging level options to filter them if not wanted.
These just slow down the system if a lot of errors occur,
stressing error handling even more.
Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Reviewed-by: NKevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NHannes Reinecke <hare@Suse.de>
Signed-off-by: NRobert Elliott <elliott@hp.com>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

report more useful information on aborts
Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Reviewed-by: NKevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NHannes Reinecke <hare@Suse.de>
Signed-off-by: NRobert Elliott <elliott@hp.com>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Improve initialization error handling in hpsa_init_one
Clean up style and indent issues
Rename functions for consistency
Improve error messaging on allocations
Fix return status from hpsa_put_ctlr_into_performant_mode
Correct free order in hpsa_init_one using new function
   hpsa_free_performant_mode
Prevent inadvertent use of null pointers by nulling out the parent structures
   and zeroing out associated size variables.
Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Reviewed-by: NKevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NHannes Reinecke <hare@Suse.de>
Signed-off-by: NRobert Elliott <elliott@hp.com>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>