After DEF_PRIORITY, balance_pgdat() considers all_unreclaimable zones to
be balanced but sleeping_prematurely does not.  This can force kswapd to
stay awake longer than it should.  This patch fixes it.
Signed-off-by: NMel Gorman <mel@csn.ul.ie>
Reviewed-by: NEric B Munson <emunson@mgebm.net>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Simon Kirby <sim@hostway.ca>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When kswapd wakes up, it reads its order and classzone from pgdat and
calls balance_pgdat.  While its awake, it potentially reclaimes at a high
order and a low classzone index.  This might have been a once-off that was
not required by subsequent callers.  However, because the pgdat values
were not reset, they remain artifically high while balance_pgdat() is
running and potentially kswapd enters a second unnecessary reclaim cycle.
Reset the pgdat order and classzone index after reading.
Signed-off-by: NMel Gorman <mel@csn.ul.ie>
Reviewed-by: NMinchan Kim <minchan.kim@gmail.com>
Reviewed-by: NKAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Reviewed-by: NEric B Munson <emunson@mgebm.net>
Cc: Simon Kirby <sim@hostway.ca>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Before kswapd goes to sleep, it uses sleeping_prematurely() to check if
there was a race pushing a zone below its watermark.  If the race
happened, it stays awake.  However, balance_pgdat() can decide to reclaim
at order-0 if it decides that high-order reclaim is not working as
expected.  This information is not passed back to sleeping_prematurely().
The impact is that kswapd remains awake reclaiming pages long after it
should have gone to sleep.  This patch passes the adjusted order to
sleeping_prematurely and uses the same logic as balance_pgdat to decide if
it's ok to go to sleep.
Signed-off-by: NMel Gorman <mel@csn.ul.ie>
Reviewed-by: NMinchan Kim <minchan.kim@gmail.com>
Reviewed-by: NKAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Reviewed-by: NEric B Munson <emunson@mgebm.net>
Cc: Simon Kirby <sim@hostway.ca>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When reclaiming for high-orders, kswapd is responsible for balancing a
node but it should not reclaim excessively.  It avoids excessive reclaim
by considering if any zone in a node is balanced then the node is
balanced.  In the cases where there are imbalanced zone sizes (e.g.
ZONE_DMA with both ZONE_DMA32 and ZONE_NORMAL), kswapd can go to sleep
prematurely as just one small zone was balanced.

This alters the sleep logic of kswapd slightly.  It counts the number of
pages that make up the balanced zones.  If the total number of balanced
pages is more than a quarter of the zone, kswapd will go back to sleep.
This should keep a node balanced without reclaiming an excessive number of
pages.
Signed-off-by: NMel Gorman <mel@csn.ul.ie>
Reviewed-by: NMinchan Kim <minchan.kim@gmail.com>
Reviewed-by: NKAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Reviewed-by: NEric B Munson <emunson@mgebm.net>
Cc: Simon Kirby <sim@hostway.ca>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Simon Kirby reported the following problem

   We're seeing cases on a number of servers where cache never fully
   grows to use all available memory.  Sometimes we see servers with 4 GB
   of memory that never seem to have less than 1.5 GB free, even with a
   constantly-active VM.  In some cases, these servers also swap out while
   this happens, even though they are constantly reading the working set
   into memory.  We have been seeing this happening for a long time; I
   don't think it's anything recent, and it still happens on 2.6.36.

After some debugging work by Simon, Dave Hansen and others, the prevaling
theory became that kswapd is reclaiming order-3 pages requested by SLUB
too aggressive about it.

There are two apparent problems here.  On the target machine, there is a
small Normal zone in comparison to DMA32.  As kswapd tries to balance all
zones, it would continually try reclaiming for Normal even though DMA32
was balanced enough for callers.  The second problem is that
sleeping_prematurely() does not use the same logic as balance_pgdat() when
deciding whether to sleep or not.  This keeps kswapd artifically awake.

A number of tests were run and the figures from previous postings will
look very different for a few reasons.  One, the old figures were forcing
my network card to use GFP_ATOMIC in attempt to replicate Simon's problem.
 Second, I previous specified slub_min_order=3 again in an attempt to
reproduce Simon's problem.  In this posting, I'm depending on Simon to say
whether his problem is fixed or not and these figures are to show the
impact to the ordinary cases.  Finally, the "vmscan" figures are taken
from /proc/vmstat instead of the tracepoints.  There is less information
but recording is less disruptive.

The first test of relevance was postmark with a process running in the
background reading a large amount of anonymous memory in blocks.  The
objective was to vaguely simulate what was happening on Simon's machine
and it's memory intensive enough to have kswapd awake.

POSTMARK
                                            traceonly          kanyzone
Transactions per second:              156.00 ( 0.00%)   153.00 (-1.96%)
Data megabytes read per second:        21.51 ( 0.00%)    21.52 ( 0.05%)
Data megabytes written per second:     29.28 ( 0.00%)    29.11 (-0.58%)
Files created alone per second:       250.00 ( 0.00%)   416.00 (39.90%)
Files create/transact per second:      79.00 ( 0.00%)    76.00 (-3.95%)
Files deleted alone per second:       520.00 ( 0.00%)   420.00 (-23.81%)
Files delete/transact per second:      79.00 ( 0.00%)    76.00 (-3.95%)

MMTests Statistics: duration
User/Sys Time Running Test (seconds)         16.58      17.4
Total Elapsed Time (seconds)                218.48    222.47

VMstat Reclaim Statistics: vmscan
Direct reclaims                                  0          4
Direct reclaim pages scanned                     0        203
Direct reclaim pages reclaimed                   0        184
Kswapd pages scanned                        326631     322018
Kswapd pages reclaimed                      312632     309784
Kswapd low wmark quickly                         1          4
Kswapd high wmark quickly                      122        475
Kswapd skip congestion_wait                      1          0
Pages activated                             700040     705317
Pages deactivated                           212113     203922
Pages written                                 9875       6363

Total pages scanned                         326631    322221
Total pages reclaimed                       312632    309968
%age total pages scanned/reclaimed          95.71%    96.20%
%age total pages scanned/written             3.02%     1.97%

proc vmstat: Faults
Major Faults                                   300       254
Minor Faults                                645183    660284
Page ins                                    493588    486704
Page outs                                  4960088   4986704
Swap ins                                      1230       661
Swap outs                                     9869      6355

Performance is mildly affected because kswapd is no longer doing as much
work and the background memory consumer process is getting in the way.
Note that kswapd scanned and reclaimed fewer pages as it's less aggressive
and overall fewer pages were scanned and reclaimed.  Swap in/out is
particularly reduced again reflecting kswapd throwing out fewer pages.

The slight performance impact is unfortunate here but it looks like a
direct result of kswapd being less aggressive.  As the bug report is about
too many pages being freed by kswapd, it may have to be accepted for now.

The second test is a streaming IO benchmark that was previously used by
Johannes to show regressions in page reclaim.

MICRO
					 traceonly  kanyzone
User/Sys Time Running Test (seconds)         29.29     28.87
Total Elapsed Time (seconds)                492.18    488.79

VMstat Reclaim Statistics: vmscan
Direct reclaims                               2128       1460
Direct reclaim pages scanned               2284822    1496067
Direct reclaim pages reclaimed              148919     110937
Kswapd pages scanned                      15450014   16202876
Kswapd pages reclaimed                     8503697    8537897
Kswapd low wmark quickly                      3100       3397
Kswapd high wmark quickly                     1860       7243
Kswapd skip congestion_wait                    708        801
Pages activated                               9635       9573
Pages deactivated                             1432       1271
Pages written                                  223       1130

Total pages scanned                       17734836  17698943
Total pages reclaimed                      8652616   8648834
%age total pages scanned/reclaimed          48.79%    48.87%
%age total pages scanned/written             0.00%     0.01%

proc vmstat: Faults
Major Faults                                   165       221
Minor Faults                               9655785   9656506
Page ins                                      3880      7228
Page outs                                 37692940  37480076
Swap ins                                         0        69
Swap outs                                       19        15

Again fewer pages are scanned and reclaimed as expected and this time the
test completed faster.  Note that kswapd is hitting its watermarks faster
(low and high wmark quickly) which I expect is due to kswapd reclaiming
fewer pages.

I also ran fs-mark, iozone and sysbench but there is nothing interesting
to report in the figures.  Performance is not significantly changed and
the reclaim statistics look reasonable.

Tgis patch:

When the allocator enters its slow path, kswapd is woken up to balance the
node.  It continues working until all zones within the node are balanced.
For order-0 allocations, this makes perfect sense but for higher orders it
can have unintended side-effects.  If the zone sizes are imbalanced,
kswapd may reclaim heavily within a smaller zone discarding an excessive
number of pages.  The user-visible behaviour is that kswapd is awake and
reclaiming even though plenty of pages are free from a suitable zone.

This patch alters the "balance" logic for high-order reclaim allowing
kswapd to stop if any suitable zone becomes balanced to reduce the number
of pages it reclaims from other zones.  kswapd still tries to ensure that
order-0 watermarks for all zones are met before sleeping.
Signed-off-by: NMel Gorman <mel@csn.ul.ie>
Reviewed-by: NMinchan Kim <minchan.kim@gmail.com>
Reviewed-by: NKAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Reviewed-by: NEric B Munson <emunson@mgebm.net>
Cc: Simon Kirby <sim@hostway.ca>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Running the annotated branch profiler on a box doing average work
(firefox, evolution, xchat, distcc farm), the likely() used in
grab_cache_page_write_begin() was incorrect most of the time:

 correct incorrect  %        Function                  File              Line
 ------- ---------  -        --------                  ----              ----
 1924262 71332401  97 grab_cache_page_write_begin    filemap.c           2206

Adding a trace_printk() and running the function tracer limited to
just this function I can see:

        gconfd-2-2696  [000]  4467.268935: grab_cache_page_write_begin: page=          (null) mapping=ffff8800676a9460 index=7
        gconfd-2-2696  [000]  4467.268946: grab_cache_page_write_begin <-ext3_write_begin
        gconfd-2-2696  [000]  4467.268947: grab_cache_page_write_begin: page=          (null) mapping=ffff8800676a9460 index=8
        gconfd-2-2696  [000]  4467.268959: grab_cache_page_write_begin <-ext3_write_begin
        gconfd-2-2696  [000]  4467.268960: grab_cache_page_write_begin: page=          (null) mapping=ffff8800676a9460 index=9
        gconfd-2-2696  [000]  4467.268972: grab_cache_page_write_begin <-ext3_write_begin
        gconfd-2-2696  [000]  4467.268973: grab_cache_page_write_begin: page=          (null) mapping=ffff8800676a9460 index=10
        gconfd-2-2696  [000]  4467.268991: grab_cache_page_write_begin <-ext3_write_begin
        gconfd-2-2696  [000]  4467.268992: grab_cache_page_write_begin: page=          (null) mapping=ffff8800676a9460 index=11
        gconfd-2-2696  [000]  4467.269005: grab_cache_page_write_begin <-ext3_write_begin

Which shows that a lot of calls from ext3_write_begin will result in the
page returned by "find_lock_page" will be NULL.
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>
Acked-by: NNick Piggin <npiggin@kernel.dk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

page_mapping() has a unlikely that the mapping has PAGE_MAPPING_ANON set.
But running the annotated branch profiler on a normal desktop system doing
vairous tasks (xchat, evolution, firefox, distcc), it is not really that
unlikely that the mapping here will have the PAGE_MAPPING_ANON flag set:

 correct incorrect  %        Function                  File              Line
 ------- ---------  -        --------                  ----              ----
35935762 1270265395  97 page_mapping                   mm.h                 659
1306198001   143659   0 page_mapping                   mm.h                 657
203131478   121586   0 page_mapping                   mm.h                 657
 5415491     1116   0 page_mapping                   mm.h                 657
74899487     1116   0 page_mapping                   mm.h                 657
203132845      224   0 page_mapping                   mm.h                 659
 5415464       27   0 page_mapping                   mm.h                 659
   13552        0   0 page_mapping                   mm.h                 657
   13552        0   0 page_mapping                   mm.h                 659
  242630        0   0 page_mapping                   mm.h                 657
  242630        0   0 page_mapping                   mm.h                 659
74899487        0   0 page_mapping                   mm.h                 659

The page_mapping() is a static inline, which is why it shows up multiple
times.

The unlikely in page_mapping() was correct a total of 1909540379 times and
incorrect 1270533123 times, with a 39% being incorrect.  With this much of
an error, it's best to simply remove the unlikely and have the compiler
and branch prediction figure this out.
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Rik van Riel <riel@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The mapping_unevictable() has a likely() around the mapping parameter.
This mapping parameter comes from page_mapping() which has an unlikely()
that the page will be set as PAGE_MAPPING_ANON, and if so, it will return
NULL.  One would think that this unlikely() means that the mapping
returned by page_mapping() would not be NULL, but where page_mapping() is
used just above mapping_unevictable(), that unlikely() is incorrect most
of the time.  This means that the "likely(mapping)" in
mapping_unevictable() is incorrect most of the time.

Running the annotated branch profiler on my main box which runs firefox,
evolution, xchat and is part of my distcc farm, I had this:

 correct incorrect  %        Function                  File              Line
 ------- ---------  -        --------                  ----              ----
12872836 1269443893  98 mapping_unevictable            pagemap.h            51
35935762 1270265395  97 page_mapping                   mm.h                 659
1306198001   143659   0 page_mapping                   mm.h                 657
203131478   121586   0 page_mapping                   mm.h                 657
 5415491     1116   0 page_mapping                   mm.h                 657
74899487     1116   0 page_mapping                   mm.h                 657
203132845      224   0 page_mapping                   mm.h                 659
 5415464       27   0 page_mapping                   mm.h                 659
   13552        0   0 page_mapping                   mm.h                 657
   13552        0   0 page_mapping                   mm.h                 659
  242630        0   0 page_mapping                   mm.h                 657
  242630        0   0 page_mapping                   mm.h                 659
74899487        0   0 page_mapping                   mm.h                 659

The page_mapping() is a static inline, which is why it shows up multiple
times.  The mapping_unevictable() is also a static inline but seems to be
used only once in my setup.

The unlikely in page_mapping() was correct a total of 1909540379 times and
incorrect 1270533123 times, with a 39% being incorrect.  Perhaps this is
enough to remove the unlikely from page_mapping() as well.
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>
Reviewed-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: NNick Piggin <npiggin@kernel.dk>
Acked-by: NRik van Riel <riel@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

IS_ERR() already implies unlikely(), so it can be omitted here.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Reviewed-by: NMinchan Kim <minchan.kim@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Today, tasklist_lock in migrate_pages doesn't protect anything.
rcu_read_lock() provide enough protection from pid hash walk.
Signed-off-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Reported-by: NPeter Zijlstra <peterz@infradead.org>
Cc: Christoph Lameter <cl@linux-foundation.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

__get_user_pages gets a new 'nonblocking' parameter to signal that the
caller is prepared to re-acquire mmap_sem and retry the operation if
needed.  This is used to split off long operations if they are going to
block on a disk transfer, or when we detect contention on the mmap_sem.

[akpm@linux-foundation.org: remove ref to rwsem_is_contended()]
Signed-off-by: NMichel Lespinasse <walken@google.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use a single code path for faulting in pages during mlock.

The reason to have it in this patch series is that I did not want to
update both code paths in a later change that releases mmap_sem when
blocking on disk.
Signed-off-by: NMichel Lespinasse <walken@google.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Move the code to mlock pages from __mlock_vma_pages_range() to
follow_page().

This allows __mlock_vma_pages_range() to not have to break down work into
16-page batches.

An additional motivation for doing this within the present patch series is
that it'll make it easier for a later chagne to drop mmap_sem when
blocking on disk (we'd like to be able to resume at the page that was read
from disk instead of at the start of a 16-page batch).
Signed-off-by: NMichel Lespinasse <walken@google.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Currently mlock() holds mmap_sem in exclusive mode while the pages get
faulted in.  In the case of a large mlock, this can potentially take a
very long time, during which various commands such as 'ps auxw' will
block.  This makes sysadmins unhappy:

real    14m36.232s
user    0m0.003s
sys     0m0.015s
(output from 'time ps auxw' while a 20GB file was being mlocked without
being previously preloaded into page cache)

I propose that mlock() could release mmap_sem after the VM_LOCKED bits
have been set in all appropriate VMAs.  Then a second pass could be done
to actually mlock the pages, in small batches, releasing mmap_sem when we
block on disk access or when we detect some contention.

This patch:

Before this change, mlock() holds mmap_sem in exclusive mode while the
pages get faulted in.  In the case of a large mlock, this can potentially
take a very long time.  Various things will block while mmap_sem is held,
including 'ps auxw'.  This can make sysadmins angry.

I propose that mlock() could release mmap_sem after the VM_LOCKED bits
have been set in all appropriate VMAs.  Then a second pass could be done
to actually mlock the pages with mmap_sem held for reads only.  We need to
recheck the vma flags after we re-acquire mmap_sem, but this is easy.

In the case where a vma has been munlocked before mlock completes, pages
that were already marked as PageMlocked() are handled by the munlock()
call, and mlock() is careful to not mark new page batches as PageMlocked()
after the munlock() call has cleared the VM_LOCKED vma flags.  So, the end
result will be identical to what'd happen if munlock() had executed after
the mlock() call.

In a later change, I will allow the second pass to release mmap_sem when
blocking on disk accesses or when it is otherwise contended, so that it
won't be held for long periods of time even in shared mode.
Signed-off-by: NMichel Lespinasse <walken@google.com>
Tested-by: NValdis Kletnieks <Valdis.Kletnieks@vt.edu>
Cc: Hugh Dickins <hughd@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When faulting in pages for mlock(), we want to break COW for anonymous or
file pages within VM_WRITABLE, non-VM_SHARED vmas.  However, there is no
need to write-fault into VM_SHARED vmas since shared file pages can be
mlocked first and dirtied later, when/if they actually get written to.
Skipping the write fault is desirable, as we don't want to unnecessarily
cause these pages to be dirtied and queued for writeback.
Signed-off-by: NMichel Lespinasse <walken@google.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Kosaki Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Theodore Tso <tytso@google.com>
Cc: Michael Rubin <mrubin@google.com>
Cc: Suleiman Souhlal <suleiman@google.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Reorganize the code so that dirty pages are handled closer to the place
that makes them dirty (handling write fault into shared, writable VMAs).
No behavior changes.
Signed-off-by: NMichel Lespinasse <walken@google.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Kosaki Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Theodore Tso <tytso@google.com>
Cc: Michael Rubin <mrubin@google.com>
Cc: Suleiman Souhlal <suleiman@google.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

mlocking a shared, writable vma currently causes the corresponding pages
to be marked as dirty and queued for writeback.  This seems rather
unnecessary given that the pages are not being actually modified during
mlock.  It is understood that for non-shared mappings (file or anon) we
want to use a write fault in order to break COW, but there is just no such
need for shared mappings.

The first two patches in this series do not introduce any behavior change.
 The intent there is to make it obvious that dirtying file pages is only
done in the (writable, shared) case.  I think this clarifies the code, but
I wouldn't mind dropping these two patches if there is no consensus about
them.

The last patch is where we actually avoid dirtying shared mappings during
mlock.  Note that as a side effect of this, we won't call page_mkwrite()
for the mappings that define it, and won't be pre-allocating data blocks
at the FS level if the mapped file was sparsely allocated.  My
understanding is that mlock does not need to provide such guarantee, as
evidenced by the fact that it never did for the filesystems that don't
define page_mkwrite() - including some common ones like ext3.  However, I
would like to gather feedback on this from filesystem people as a
precaution.  If this turns out to be a showstopper, maybe block
preallocation can be added back on using a different interface.

Large shared mlocks are getting significantly (>2x) faster in my tests, as
the disk can be fully used for reading the file instead of having to share
between this and writeback.

This patch:

Reorganize the code to remove the 'reuse' flag.  No behavior changes.
Signed-off-by: NMichel Lespinasse <walken@google.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Kosaki Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Theodore Tso <tytso@google.com>
Cc: Michael Rubin <mrubin@google.com>
Cc: Suleiman Souhlal <suleiman@google.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Temporary IO failures, eg.  due to loss of both multipath paths, can
permanently leave the PageError bit set on a page, resulting in msync or
fsync returning -EIO over and over again, even if IO is now getting to the
disk correctly.

We already clear the AS_ENOSPC and AS_IO bits in mapping->flags in the
filemap_fdatawait_range function.  Also clearing the PageError bit on the
page allows subsequent msync or fsync calls on this file to return without
an error, if the subsequent IO succeeds.

Unfortunately data written out in the msync or fsync call that returned
-EIO can still get lost, because the page dirty bit appears to not get
restored on IO error.  However, the alternative could be potentially all
of memory filling up with uncleanable dirty pages, hanging the system, so
there is no nice choice here...
Signed-off-by: NRik van Riel <riel@redhat.com>
Acked-by: NValerie Aurora <vaurora@redhat.com>
Acked-by: NJeff Layton <jlayton@redhat.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Acked-by: NJan Kara <jack@suse.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We'd like to be able to oom_score_adj a process up/down as it
enters/leaves the foreground.  Currently, it is not possible to oom_adj
down without CAP_SYS_RESOURCE.  This patch allows a task to decrease its
oom_score_adj back to the value that a CAP_SYS_RESOURCE thread set it to
or its inherited value at fork.  Assuming the thread that has forked it
has oom_score_adj of 0, each process could decrease it back from 0 upon
activation unless a CAP_SYS_RESOURCE thread elevated it to something
higher.

Alternative considered:

* a setuid binary
* a daemon with CAP_SYS_RESOURCE

Since you don't wan't all processes to be able to reduce their oom_adj, a
setuid or daemon implementation would be complex.  The alternatives also
have much higher overhead.

This patch updated from original patch based on feedback from David
Rientjes.
Signed-off-by: NMandeep Singh Baines <msb@chromium.org>
Acked-by: NDavid Rientjes <rientjes@google.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Ying Han <yinghan@google.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Four architectures (arm, mips, sparc, x86) use __vmalloc_area() for
module_init().  Much of the code is duplicated and can be generalized in a
globally accessible function, __vmalloc_node_range().

__vmalloc_node() now calls into __vmalloc_node_range() with a range of
[VMALLOC_START, VMALLOC_END) for functionally equivalent behavior.

Each architecture may then use __vmalloc_node_range() directly to remove
the duplication of code.
Signed-off-by: NDavid Rientjes <rientjes@google.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

pcpu_get_vm_areas() only uses GFP_KERNEL allocations, so remove the gfp_t
formal and use the mask internally.
Signed-off-by: NDavid Rientjes <rientjes@google.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

get_vm_area_node() is unused in the kernel and can thus be removed.
Signed-off-by: NDavid Rientjes <rientjes@google.com>
Cc: Christoph Lameter <cl@linux.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

With compaction being used instead of lumpy reclaim, the name lumpy_mode
and associated variables is a bit misleading.  Rename lumpy_mode to
reclaim_mode which is a better fit.  There is no functional change.
Signed-off-by: NMel Gorman <mel@csn.ul.ie>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Rik van Riel <riel@redhat.com>
Acked-by: NJohannes Weiner <hannes@cmpxchg.org>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

try_to_compact_pages() is initially called to only migrate pages
asychronously and kswapd always compacts asynchronously.  Both are being
optimistic so it is important to complete the work as quickly as possible
to minimise stalls.

This patch alters the scanner when asynchronous to only consider
MIGRATE_MOVABLE pageblocks as migration candidates.  This reduces stalls
when allocating huge pages while not impairing allocation success rates as
a full scan will be performed if necessary after direct reclaim.
Signed-off-by: NMel Gorman <mel@csn.ul.ie>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Rik van Riel <riel@redhat.com>
Acked-by: NJohannes Weiner <hannes@cmpxchg.org>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

With the introduction of the boolean sync parameter, the API looks a
little inconsistent as offlining is still an int.  Convert offlining to a
bool for the sake of being tidy.
Signed-off-by: NMel Gorman <mel@csn.ul.ie>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Rik van Riel <riel@redhat.com>
Acked-by: NJohannes Weiner <hannes@cmpxchg.org>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

mm: migration: allow migration to operate asynchronously and avoid synchronous compaction in the faster path

Migration synchronously waits for writeback if the initial passes fails.
Callers of memory compaction do not necessarily want this behaviour if the
caller is latency sensitive or expects that synchronous migration is not
going to have a significantly better success rate.

This patch adds a sync parameter to migrate_pages() allowing the caller to
indicate if wait_on_page_writeback() is allowed within migration or not.
For reclaim/compaction, try_to_compact_pages() is first called
asynchronously, direct reclaim runs and then try_to_compact_pages() is
called synchronously as there is a greater expectation that it'll succeed.

[akpm@linux-foundation.org: build/merge fix]
Signed-off-by: NMel Gorman <mel@csn.ul.ie>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Rik van Riel <riel@redhat.com>
Acked-by: NJohannes Weiner <hannes@cmpxchg.org>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Lumpy reclaim is disruptive.  It reclaims a large number of pages and
ignores the age of the pages it reclaims.  This can incur significant
stalls and potentially increase the number of major faults.

Compaction has reached the point where it is considered reasonably stable
(meaning it has passed a lot of testing) and is a potential candidate for
displacing lumpy reclaim.  This patch introduces an alternative to lumpy
reclaim whe compaction is available called reclaim/compaction.  The basic
operation is very simple - instead of selecting a contiguous range of
pages to reclaim, a number of order-0 pages are reclaimed and then
compaction is later by either kswapd (compact_zone_order()) or direct
compaction (__alloc_pages_direct_compact()).

[akpm@linux-foundation.org: fix build]
[akpm@linux-foundation.org: use conventional task_struct naming]
Signed-off-by: NMel Gorman <mel@csn.ul.ie>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Rik van Riel <riel@redhat.com>
Acked-by: NJohannes Weiner <hannes@cmpxchg.org>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Currently lumpy_mode is an enum and determines if lumpy reclaim is off,
syncronous or asyncronous.  In preparation for using compaction instead of
lumpy reclaim, this patch converts the flags into a bitmap.
Signed-off-by: NMel Gorman <mel@csn.ul.ie>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In preparation for a patches promoting the use of memory compaction over
lumpy reclaim, this patch adds trace points for memory compaction
activity.  Using them, we can monitor the scanning activity of the
migration and free page scanners as well as the number and success rates
of pages passed to page migration.
Signed-off-by: NMel Gorman <mel@csn.ul.ie>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Currently there is no way to find whether a process has locked its pages
in memory or not.  And which of the memory regions are locked in memory.

Add a new field "Locked" to export this information via the smaps file.
Signed-off-by: NNikanth Karthikesan <knikanth@suse.de>
Acked-by: NBalbir Singh <balbir@linux.vnet.ibm.com>
Acked-by: NWu Fengguang <fengguang.wu@intel.com>
Cc: Matt Mackall <mpm@selenic.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NPekka Enberg <penberg@kernel.org>
Cc: Jiri Kosina <trivial@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Merge mpage_end_io_read() and mpage_end_io_write() into mpage_end_io() to
eliminate code duplication.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NHai Shan <shan.hai@windriver.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Testing ->mapping and ->index without a ref is not stable as the page
may have been reused at this point.
Signed-off-by: NNick Piggin <npiggin@kernel.dk>
Reviewed-by: NWu Fengguang <fengguang.wu@intel.com>
Reviewed-by: NMinchan Kim <minchan.kim@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Currently, kswapd() has deep nesting and is slightly hard to read.  Clean
this up.
Signed-off-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

__set_page_dirty_no_writeback() should return true if it actually
transitioned the page from a clean to dirty state although it seems nobody
uses its return value at present.
Signed-off-by: NBob Liu <lliubbo@gmail.com>
Acked-by: NWu Fengguang <fengguang.wu@intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use correct function name, remove incorrect apostrophe

Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When wb_writeback() is called in WB_SYNC_ALL mode, work->nr_to_write is
usually set to LONG_MAX.  The logic in wb_writeback() then calls
__writeback_inodes_sb() with nr_to_write == MAX_WRITEBACK_PAGES and we
easily end up with non-positive nr_to_write after the function returns, if
the inode has more than MAX_WRITEBACK_PAGES dirty pages at the moment.

When nr_to_write is <= 0 wb_writeback() decides we need another round of
writeback but this is wrong in some cases!  For example when a single
large file is continuously dirtied, we would never finish syncing it
because each pass would be able to write MAX_WRITEBACK_PAGES and inode
dirty timestamp never gets updated (as inode is never completely clean).
Thus __writeback_inodes_sb() would write the redirtied inode again and
again.

Fix the issue by setting nr_to_write to LONG_MAX in WB_SYNC_ALL mode.  We
do not need nr_to_write in WB_SYNC_ALL mode anyway since
write_cache_pages() does livelock avoidance using page tagging in
WB_SYNC_ALL mode.

This makes wb_writeback() call __writeback_inodes_sb() only once on
WB_SYNC_ALL.  The latter function won't livelock because it works on

- a finite set of files by doing queue_io() once at the beginning
- a finite set of pages by PAGECACHE_TAG_TOWRITE page tagging

After this patch, program from http://lkml.org/lkml/2010/10/24/154 is no
longer able to stall sync forever.

[fengguang.wu@intel.com: fix locking comment]
Signed-off-by: NJan Kara <jack@suse.cz>
Signed-off-by: NWu Fengguang <fengguang.wu@intel.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jan Engelhardt <jengelh@medozas.de>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Background writeback is easily livelockable in a loop in wb_writeback() by
a process continuously re-dirtying pages (or continuously appending to a
file).  This is in fact intended as the target of background writeback is
to write dirty pages it can find as long as we are over
dirty_background_threshold.

But the above behavior gets inconvenient at times because no other work
queued in the flusher thread's queue gets processed.  In particular, since
e.g.  sync(1) relies on flusher thread to do all the IO for it, sync(1)
can hang forever waiting for flusher thread to do the work.

Generally, when a flusher thread has some work queued, someone submitted
the work to achieve a goal more specific than what background writeback
does.  Moreover by working on the specific work, we also reduce amount of
dirty pages which is exactly the target of background writeout.  So it
makes sense to give specific work a priority over a generic page cleaning.

Thus we interrupt background writeback if there is some other work to do.
We return to the background writeback after completing all the queued
work.

This may delay the writeback of expired inodes for a while, however the
expired inodes will eventually be flushed to disk as long as the other
works won't livelock.

[fengguang.wu@intel.com: update comment]
Signed-off-by: NJan Kara <jack@suse.cz>
Signed-off-by: NWu Fengguang <fengguang.wu@intel.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jan Engelhardt <jengelh@medozas.de>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This tracks when balance_dirty_pages() tries to wakeup the flusher thread
for background writeback (if it was not started already).
Suggested-by: NChristoph Hellwig <hch@infradead.org>
Signed-off-by: NWu Fengguang <fengguang.wu@intel.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Jan Engelhardt <jengelh@medozas.de>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Check whether background writeback is needed after finishing each work.

When bdi flusher thread finishes doing some work check whether any kind of
background writeback needs to be done (either because
dirty_background_ratio is exceeded or because we need to start flushing
old inodes).  If so, just do background write back.

This way, bdi_start_background_writeback() just needs to wake up the
flusher thread.  It will do background writeback as soon as there is no
other work.

This is a preparatory patch for the next patch which stops background
writeback as soon as there is other work to do.
Signed-off-by: NJan Kara <jack@suse.cz>
Signed-off-by: NWu Fengguang <fengguang.wu@intel.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jan Engelhardt <jengelh@medozas.de>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>