Add a function which indicates our intention to enable or disable a particular
Tx queue. Also add a function to notify the device's Tx unit that we're about
to enable or disable a Tx queue.

Change-ID: I6adf3cbb5bb3e3c984d1ec969e06577c19ef296d
Signed-off-by: NMatt Jared <matthew.a.jared@intel.com>
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

B0 Si blocks AQ registers when in Blank Flash mode - write is dropped,
read gives 0xDEADBEEF. Introduce a simple check for a correct value in one
of the AQ registers to be sure that AQ was configured correctly.
Without this check we get into an endless loop while trying to send
GetVersion AQ cmd.

Change-ID: I00102b8c5fa6c16d14289be677aafadf87f10f0d
Signed-off-by: NKamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Depending on the timing of what the PF driver is doing, it make take a
few tries before the VF driver is able to communicate with the PF driver
on init or reset recovery. In order to prevent confusion, make the most
common messages less scary by lowering them to a less terrifying log
level and indicate that the driver will retry.

Change-ID: I1ec22aa59a68f4469aabe14775a1bfc1ab4b7f2f
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The driver and hardware are not expected to work correctly
with revision_id 0 hardware.  Don't prevent the user from
using it, but be sure to print a warning.

Change-ID: I3712d34752bfad458078a5f35dfd0aa0ae9fd20e
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Print the VEB statistics in the ethtool stats output.

Change-ID: Ic93d4c3922345c43e4cfd7f7e7a906844dd2f49f
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When the VEB is created for the basic LAN device and its VSIs, we need to
set the tracking lan_veb index for later use.

Change-ID: I66bb74993bbda3621ca557437cb4b3517f9b315b
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The SYSTEMPORT driver uses libphy to determine the carrier state, so
make sure we start with a carrier off until libphy has completed the
link training process.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The comment about how the hardware prepends 2bytes to align the IP
header on a 4-byte boundary was not correct, fix that.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We were missing an and comparison with status to check whether
RX_STATUS_OVFLOW is asserted or not in the per-packet status word, fix
that.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Our transmit locking scheme did not account for the TX ring full
interrupt. If a TX ring full interrupt fires while we are attempting to
transmit, we will cause a deadlock to occur. Fix this by making sure
that we properly disable interrupts while acquiring the spinlock.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch provides the Kconfig and Makefile changes needed
to configure and build the AMD 10GbE platform driver and the
AMD 10GbE phylib driver.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch provides the initial phylib driver in support
of the AMD 10GbE device.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch provides the initial platform driver for the AMD
10GbE device.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers/net/ethernet/amd/hplance.h:
 #define HPLANCE_MEMOFF 0x8000   /* struct lance_init_block */
 #define HPLANCE_NVRAMOFF 0xC008 /* etheraddress as one *nibble* per byte */

The offset of RAM start is 0x8000, the offset of RAM end is 0xC008,
so the RAM size is 16392 bytes.
Signed-off-by: NAmos Kong <akong@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The order of ram pages is 3, so the ram size is 2^3 * 4K = 32K.
Signed-off-by: NAmos Kong <akong@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On the DM9000B, dm9000_msleep() is called during the dm9000_timeout()
routine.  Since dm9000_timeout() holds the main spinlock through the
entire routine, mdelay() needs to be used rather than msleep().
Furthermore, the mutex_lock()/mutex_unlock() should be avoided so as to
not sleep with spinlocks held.
Signed-off-by: NAndrew Ruder <andrew.ruder@elecsyscorp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On the DM9000A/DM9000B force the initial check of the link status.  The
DM9000A/B has a link status changed event and this interrupt bit isn't
always set out of reset when a cable is plugged in.  This results in the
driver not seeing the cable attached link status until the cable is
removed and plugged in again.
Signed-off-by: NAndrew Ruder <andrew.ruder@elecsyscorp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since dm9000_interrupt() is already reading/clearing every set bit in
DM9000_ISR, this additional clear in dm9000_rx() (which is only called
by dm9000_interrupt()) is unnecessary and can be removed.
Signed-off-by: NAndrew Ruder <andrew.ruder@elecsyscorp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

DM9000 uses level-triggered interrupts.  Some systems (PXA270) only
support edge-triggered interrupts on GPIOs.  Some changes are necessary
to ensure that interrupts are not triggered while the GPIO interrupt is
masked or we will miss the interrupt forever.

* Make some helper functions called dm9000_mask_interrupts() and
  dm9000_unmask_interrupts() for readability.

* dm9000_init_dm9000(): ensure that this function always leaves interrupts
  masked regardless of the state when it entered the function.  This is
  primarily to support the situation in dm9000_open where the logic used
  to go:

    dm9000_open()
        dm9000_init_dm9000()
            unmask interrupts
        request_irq()

  If an interrupt occurred between unmasking the interrupt and
  requesting the irq, it would be missed forever as the edge event would
  never be seen by the GPIO hardware in the PXA270.  This allows us to
  change the logic to:

    dm9000_open()
        dm9000_init_dm9000()
            dm9000_mask_interrupts()
        request_irq()
        dm9000_unmask_interrupts()

* dm9000_timeout(), dm9000_drv_resume(): Add the missing
  dm9000_unmask_interrupts() now required by the change above.

* dm9000_shutdown(): Use mask helper function

* dm9000_interrupt(): Use mask/unmask helper functions
Signed-off-by: NAndrew Ruder <andrew.ruder@elecsyscorp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* Change a hard-coded 0x3 to NCR_RST | NCR_MAC_LBK in dm9000_reset

* Every single place where dm9000_init_dm9000 was ran, a dm9000_reset
  was called immediately before-hand.  Bring dm9000_reset into
  dm9000_init_dm9000.

* The following commit updated the dm9000_probe reset routine to use NCR_RST
  | NCR_MAC_LBK:

    6741f40d DM9000B: driver initialization upgrade

  and a later commit added a bug-fix to always reset the chip twice:

    09ee9f87 dm9000: Implement full reset of DM9000 network device

  Unfortunately, since the changes in 6741f40d were made by replacing the
  dm9000_probe dm9000_reset with the adjusted iow(), the changes in
  09ee9f87 were not incorporated into the dm9000_probe reset.
  Furthermore, it bypassed the requisite reset-delay causing some boards
  to get at least one "read wrong id ..." dev_err message during
  dm9000_probe.
Signed-off-by: NAndrew Ruder <andrew.ruder@elecsyscorp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The DM9000 supports both active high interrupts and active low interrupts.
This is configured via the attached EEPROM.  In the device-tree case, make sure
that the DM9000 driver passes the correct flags to request_irq.
Signed-off-by: NAndrew Ruder <andrew.ruder@elecsyscorp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A recent commit (a02eb4 "xen-netback: worse-case estimate in xenvif_rx_action is
underestimating") capped the slot estimation to MAX_SKB_FRAGS, but that triggers
the next BUG_ON a few lines down, as the packet consumes more slots than
estimated.
This patch introduces full_coalesce on the skb callback buffer, which is used in
start_new_rx_buffer() to decide whether netback needs coalescing more
aggresively. By doing that, no packet should need more than
(XEN_NETIF_MAX_TX_SIZE + 1) / PAGE_SIZE data slots (excluding the optional GSO
slot, it doesn't carry data, therefore irrelevant in this case), as the provided
buffers are fully utilized.
Signed-off-by: NZoltan Kiss <zoltan.kiss@citrix.com>
Cc: Paul Durrant <paul.durrant@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: NPaul Durrant <paul.durrant@gmail.com>
Acked-by: NWei Liu <wei.liu2@citrix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Uninitialzed fields in mailbox command structure
  caused commands to time out randomly due to garbage
  values so initialize it to zero.
Signed-off-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Quoting David Miller:
"At the moment you call register_netdev() the device is visible, notifications
are sent to userspace, and userland tools can try to bring the interface up
and see the incorrect link state, before you do the netif_carrier_off().

Said another way, between the register_netdev() and netif_carrier_off() call,
userspace can see the device in an inconsistent state."

So call netif_carrier_off() prior to register_netdev().
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a couple more statistics that the hardware offers but aren't part
of the standard netdev stats.

Change-ID: I201db2898f2c284aee3d9631470bc5edd349e9a5
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The rx_errors (GLV_REPC) and rx_missed (GLV_RMPC) were removed
from the chip design.

Change-ID: Ifdeb69c90feac64ec95c36d3d32c75e3a06de3b7
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Pull the PF stat collection out of the VSI collection routine, and
add a unifying stats update routine to call the various stat collection
routines.

Change-ID: I224192455bb3a6e5dc0a426935e67dffc123e306
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change moves some common code in two places into a
small helper function, and corrects a bug in one of the
two places in the process.

Change-ID: If3bba7152b240f13a7881eb0e8a781655fa66ce7
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Structure for VEB context added. Update macro for
transition from ms to GTIME (us) time units.

Change-ID: Ib3a19587b4cf355348655df8f60c6f37bb1497a3
Signed-off-by: NKamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently, the PF driver only notifies the VFs for PF reset events.
Instead, notify the VFs for all types of resets, so they can attempt a
graceful reinit.

Change-ID: I03eb7afde25727198ef620f8b4e78bb667a11370
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

i40evf_set_ringparam was broken in several ways. First, it only changed
the size of the first ring, and second, changing the ring size would
often result in a panic because it would change the count before
deallocating resources, causing the driver to either free nonexistent
buffers, or leak leftover buffers.

Fix this by storing the descriptor count in the adapter structure, and
updating the count for each ring each time we allocate them. This
ensures that we always free the right size ring, and always end up with
the requested count when the device is (re)opened.

Change-ID: I298396cd3d452ba8509d9f2d33a93f25868a9a55
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Hardware requires descriptors to be allocated in groups of 32.

Change-ID: I752ccc96769d1bd8d3018c004b8aeff464045bf2
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The driver was allowing the user to set larger size MTU
than the hardware was being configured to support.

The driver was already using VLAN_HLEN when setting the
hardware max receivable frame size, so just add it to the
netdev MTU set entry point as well.

Change-ID: Ie20e2a35d04f8c411253e255bea79ca69aaeaea3
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove unused defines and macros for RX_LRO.

Change-ID: I8ca6715edfa62b56837417a1c4ff68c2345dab6e
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We introduced this check in case this structure changed in the future,
the AQ definition is now mature enough that this check is no longer necessary.

Change-ID: Ic66321d0a08557dc9d8cb84029185352cb534330
Signed-off-by: NKamil Krawczyk <kamil.krawczyk@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Register range, being subject to register diagnostic, can vary among
different NVMs. We will try to identify the full range and use it for
a register test. This is needed to avoid false test results. If we fail
to define the proper register range we will test only the first register
from that group.

Change-ID: Ieee7173c719733b61d3733177a94dc557eb7b3fd
Signed-off-by: NKamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

A couple of FD checks ended up using bitwise OR to check
a value, which ends up always being evaluated to true.

This should fix the issue.  Thanks to DaveJ for noticing
and reporting the issue!

CC: Dave Jones <davej@redhat.com>
Reported-by: NDave Jones <davej@redhat.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Added VXLAN link configuration for sending UDP checksums, and allowing
TX and RX of UDP6 checksums.

Also, call common iptunnel_handle_offloads and added GSO support for
checksums.
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To make TLB mode work, the patch allows learning packets
to be sent using mac addresses assigned to macvlan devices,
also taking into an account vlans that may be between the
bond and macvlan device.

To make RLB work, all we have to do is accept ARP packets
for addresses added to the bond dev->uc list.  Since RLB
mode will take care to update the peers directly with
correct mac addresses, learning packets for these addresses
do not have be send to switch.
Signed-off-by: NVlad Yasevich <vyasevic@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bonding and team drivers generate specific events during failover
that trigger switch updates.  When a macvlan device is configured
on top of bonding, we want switches to learn about the macvlan
devices as well.   This patch adds a handler to macvlan driver to
propagate these events to all macvlan devices.  We let the generic
inetdev event handler do the work.

This allows macvlan to operated correctly over active-backup
mode bond.
Signed-off-by: NVlad Yasevich <vyasevic@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>