A logic error here results in the adapter_stopped flag only being
cleared when ixgbe_setup_fc returns an error. Correct the logic.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change does two things. First, it makes it so that we always
set the relaxed ordering bits related to the DCA registers even if
DCA is not enabled. Second, it moves the configuration out of the
ixgbe_down function and into the ixgbe_configure function before
enabling the Rx and Tx rings. This ensures that DCA is configured
correctly before starting to process packets.

Thanks to Alex Duyck for this fix.

CC: Alex Duyck <aduyck@mirantis.com>
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add new device ID for X550EM device with SFPs.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch skips the PCI transactions pending check in
ixgbe_disable_pcie_master. This is done to addresses a known HW
issue where the PCI transactions pending bit sticks high when there
are pending transactions. HW engineering instructed to workaround
this issue by wait and then continue with our reset flow.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch sets RDRXCTL.PSP when the driver is in SRIOV mode which
enables padding of small packets.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Setting the X550* RDRXCTL register should fall through into X540
and 82599, not 82598.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The timeout path is supposed to release the semaphore, so do that.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Take control of an I2C mux that selects which SFP is attached to
the I2C bus. The control of the mux is captured in the taking and
releasing of the related semaphore. Because only port 1 can control
the mux, port 1 always leaves the mux set to select port 0.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Reduce the frequency of polling for SFP modules. Because the
service task sometimes runs at high rates, we can poll for
SFPs too often. When an SFP is not present, the I2C timeouts
that result are very costly. So, prevent SFP polling from
being done more than once every two seconds. To reduce latency,
the poll time is cleared in a couple of cases to permit the
next service task execution to poll the SFP module.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Since SFP+ can be used with some X550 devices, permit them to be
detected.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

On some hardware platforms, the CS4227 does not initialize properly.
Detect those cases and reset it appropriately.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Configures the CS4227 correctly for both 1G and 10G operation,
by moving the code to ixgbe_setup_mac_link_sfp_x550em(). It
needs to be in this function because we need both the module
type and the speed, and this is the only function in the init
flow that knows the speed. In contrast,
ixgbe_setup_sfp_modules_X550em() does not know the speed, so we
can't do anything useful here. This is a fundamental difference
from the previous flow, and is due to the way the CS4227 is
implemented.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds X550EM_x SFP+ dual-speed support. 82599 fiber link
code was moved from ixgbe_82599.c to ixgbe_common.c for use by
X550EM. SFP MAC link code is added to x550EM.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Reduce the number of retries during PHY detection. This reduces
pauses when no SFP is present. Once an SFP is detected, the normal
retry count will be used.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Clear the destination location for I2C data initially so that
the received data will not be affected by previous attempts.
This could have returned wrong data in certain retry sequences.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Set the bit banging mode in the hardware when performing bit banging
I2C operations on X550. Also control the output enable on both the
clock and data lines.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The lan_id is being set after a previous I2C eeprom access which
makes no sense because it needs to be set before any access. Move
the setting to before the access.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Most I2C accesses take and release semaphores for each access. Now
there is a reason to perform multiple I2C operations under the same
holding of the semaphore, so provide unlocked I2C methods for that
purpose.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Provide I2C combined operations on X550EM, not X550 devices.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add support for the SFP insertion interrupt on X550EM devices with
SFPs.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When an SFP not present error is returned by the reset_hw method,
accept it and go on, since an SFP can still be inserted. Previously
it was only accepted for 82598 devices.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Setting ndo_features_check to passthru_features_check allows the driver
to skip the check for multiple tagged TSO packets and enables stacked
VLAN TSO.
Tested with 82599ES.
Signed-off-by: NToshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Setting ndo_features_check to passthru_features_check allows the driver
to skip the check for multiple tagged TSO packets and enables stacked
VLAN TSO.
Tested with I217-LM.
Signed-off-by: NToshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Setting ndo_features_check to passthru_features_check allows the driver
to skip the check for multiple tagged TSO packets and enables stacked
VLAN TSO.
Tested with I350.
Signed-off-by: NToshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The device probe method e1000_probe calls e1000_init_eeprom_params
itself so there's no reason to call it again from e1000_do_write_eeprom
or e1000_do_read_eeprom.

The sentence above assumes that e1000_init_eeprom_params is effective.
e1000_init_eeprom_params depends mostly on hw->mac_type and e1000_probe
bails out early if it can't set mac_type (see e1000_init_hw_struct, then
e1000_set_mac_type), qed.

Btw, if effective, the removed paths would had been deadlock prone when
e1000_eeprom_spi was set:
-> e1000_write_eeprom (takes e1000_eeprom_lock)
   -> e1000_do_write_eeprom
      -> e1000_init_eeprom_params
         -> e1000_read_eeprom (takes e1000_eeprom_lock)

(same narrative with e1000_read_eeprom -> e1000_do_read_eeprom etc.)

As a final note, the candidate deadlock above can't happen in e1000_probe
due to the way eeprom->word_size is set / tested.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add a private ethtool flag to enable display of these statistics, which
are generally less useful. However, sometimes it can be useful for
debugging purposes. The most useful portion is the ability to see what
the PF thinks the VF mailboxes look like.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When we connect to the mailbox, we insert a fake disconnect header so
that the code does not see an invalid header and thus instantly error
every time we bring up the mailbox. However, we incorrectly record the
tail and head from the local perspective. Since the remote end shouldn't
have anything for us, add a "create_fake_disconnect_hdr" function which
inverts the TAIL and HEAD fields. This enables us to connect without any
errors of either TAIL or HEAD incorrectness, and prevents creating
extraneous error messages. This is necessary now since mbx_reset_work
does not actually reset the Tx FIFO head and tail pointers, thus head
and tail might not be equivalent on a reconnect.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes a corner case issue with the PF/VF mailbox code.
Currently, fm10k_mbx_reset_work clears various state about the mailbox.
However, it does not clear the Tx FIFO head/tail pointers. We can't
simply clear these pointers as we unintentionally drop untransmitted
messages without error.

Doing nothing results in a possible phantom re-transmission of messages,
since we leave tx.head and tx.tail intact, but clear the tx_pulled and
tail_len values. This means that the PF could continuously re-send a
message which triggers a reset in the VF. Upon reset, the VF will
re-receive the same message after a reconnect.

If we reset the tx.head and tx.tail pointers completely, we end up
dropping some messages that were pending before connect. This results in
missing LPORT_MSG_READY bits, and VFs will end up reporting no link.

However, we can resolve both issues by simply incrementing head to
account for the already transmitted messages, before we reset tx_pulled.
We do this via the same logic as fm10k_mbx_head_pull.

We account for the tail_len which includes all data not yet transmitted,
once we account for the acked data which means re-reading the HEAD
variable from the message header. Then, we drop messages until we've
dropped more than the new tx_pulled value. At this point, resetting
tail_len and tx_pulled, but not tx.head and tx.tail will result in
prevention of the phantom message. It also prevents us from dropping
untransmitted messages upon attempting to Tx into a connect or
disconnect header.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

X550 has HW support for SCTP flow director filters SCTP mask. This
patch adds it like we do for UDP and TCP.
Signed-off-by: NDonald C Skidmore <donald.c.skidmore@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is part of the future enablement of X550 SFP+ support.  This
HW uses different SDP so the interrupts need to be set up accordingly.
Signed-off-by: NDonald C Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This comment is no longer true due to a couple of mailbox locking
refactors, and we now don't actually do any rtnl protected operations
directly in the mailbox path. Remove this comment as it is factually
incorrect and confusing.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Bump.

Change-ID: If7ce84218361defa209142d1d8c6f69d48c2d7ad
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add a facility to recover the result of a previously run AQ command.

Change-ID: I21afec2c20c1a5e6ba60c7fbfcbedfff78c10e45
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add a facility to run AQ commands through the nvmupdate utility in order
to allow the update tools to interact with the FW and do special
commands needed for updates and configuration changes.

Change-ID: I5c41523e4055b37f8e4ee479f7a0574368f4a588
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This adds wait states to the NVM update state machine to signify when
waiting for an update operation to finish, whether we're in the middle
of a set of Write operations, or we're now idle but waiting.

Change-ID: Iabe91d6579ef6a2ea560647e374035656211ab43
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This adds a new GetStatus command so that the NVM update tool can query
the current status instead of doing fake write requests to probe for
readiness.

Change-ID: I671ec6ccd4dfc9dbac3a03b964589d693fda5cd8
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If the writeback descriptor buffer was previously created, this gives it
to the AQ command request to be used to save the results.

Change-ID: I8c8a1af81e6ebed6d0a15ed31697fe1a6c4e3708
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add the ability to save the AdminQ write back descriptor if a
caller supplies a buffer for it to be saved into.

Change-ID: I3d1301d26360b39a2d66dc8569e851f54133a3af
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This code returns something that becomes the errno value from ethtool and
passes around a pointer to an errno variable.  This patch changes the name
slightly to differentiate it from the actual user errno variable.

Change-ID: Idaa37845c069e66f4cea072e90f471bb2142454d
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>