Sanitize FCSR Cause bit handling, following a trail of past attempts:

* commit 42495484 ("MIPS: ptrace: Fix FP context restoration FCSR
regression"),

* commit 443c4403 ("MIPS: Always clear FCSR cause bits after
emulation"),

* commit 64bedffe ("MIPS: Clear [MSA]FPE CSR.Cause after
notify_die()"),

* commit b1442d39 ("MIPS: Prevent user from setting FCSR cause
bits"),

* commit b54d2901517d ("Properly handle branch delay slots in connection
with signals.").

Specifically do not mask these bits out in ptrace(2) processing and send
a SIGFPE signal instead whenever a matching pair of an FCSR Cause and
Enable bit is seen as execution of an affected context is about to
resume.  Only then clear Cause bits, and even then do not clear any bits
that are set but masked with the respective Enable bits.  Adjust Cause
bit clearing throughout code likewise, except within the FPU emulator
proper where they are set according to IEEE 754 exceptions raised as the
operation emulated executed.  Do so so that any IEEE 754 exceptions
subject to their default handling are recorded like with operations
executed by FPU hardware.
Signed-off-by: NMaciej W. Rozycki <macro@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14460/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

In some cases the kernel needs to execute an instruction from the delay
slot of an emulated branch instruction. These cases include:

  - Emulated floating point branch instructions (bc1[ft]l?) for systems
    which don't include an FPU, or upon which the kernel is run with the
    "nofpu" parameter.

  - MIPSr6 systems running binaries targeting older revisions of the
    architecture, which may include branch instructions whose encodings
    are no longer valid in MIPSr6.

Executing instructions from such delay slots is done by writing the
instruction to memory followed by a trap, as part of an "emuframe", and
executing it. This avoids the requirement of an emulator for the entire
MIPS instruction set. Prior to this patch such emuframes are written to
the user stack and executed from there.

This patch moves FP branch delay emuframes off of the user stack and
into a per-mm page. Allocating a page per-mm leaves userland with access
to only what it had access to previously, and compared to other
solutions is relatively simple.

When a thread requires a delay slot emulation, it is allocated a frame.
A thread may only have one frame allocated at any one time, since it may
only ever be executing one instruction at any one time. In order to
ensure that we can free up allocated frame later, its index is recorded
in struct thread_struct. In the typical case, after executing the delay
slot instruction we'll execute a break instruction with the BRK_MEMU
code. This traps back to the kernel & leads to a call to do_dsemulret
which frees the allocated frame & moves the user PC back to the
instruction that would have executed following the emulated branch.
In some cases the delay slot instruction may be invalid, such as a
branch, or may trigger an exception. In these cases the BRK_MEMU break
instruction will not be hit. In order to ensure that frames are freed
this patch introduces dsemul_thread_cleanup() and calls it to free any
allocated frame upon thread exit. If the instruction generated an
exception & leads to a signal being delivered to the thread, or indeed
if a signal simply happens to be delivered to the thread whilst it is
executing from the struct emuframe, then we need to take care to exit
the frame appropriately. This is done by either rolling back the user PC
to the branch or advancing it to the continuation PC prior to signal
delivery, using dsemul_thread_rollback(). If this were not done then a
sigreturn would return to the struct emuframe, and if that frame had
meanwhile been used in response to an emulated branch instruction within
the signal handler then we would execute the wrong user code.

Whilst a user could theoretically place something like a compact branch
to self in a delay slot and cause their thread to become stuck in an
infinite loop with the frame never being deallocated, this would:

  - Only affect the users single process.

  - Be architecturally invalid since there would be a branch in the
    delay slot, which is forbidden.

  - Be extremely unlikely to happen by mistake, and provide a program
    with no more ability to harm the system than a simple infinite loop
    would.

If a thread requires a delay slot emulation & no frame is available to
it (ie. the process has enough other threads that all frames are
currently in use) then the thread joins a waitqueue. It will sleep until
a frame is freed by another thread in the process.

Since we now know whether a thread has an allocated frame due to our
tracking of its index, the cookie field of struct emuframe is removed as
we can be more certain whether we have a valid frame. Since a thread may
only ever have a single frame at any given time, the epc field of struct
emuframe is also removed & the PC to continue from is instead stored in
struct thread_struct. Together these changes simplify & shrink struct
emuframe somewhat, allowing twice as many frames to fit into the page
allocated for them.

The primary benefit of this patch is that we are now free to mark the
user stack non-executable where that is possible.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com>
Cc: Maciej Rozycki <maciej.rozycki@imgtec.com>
Cc: Faraz Shahbazker <faraz.shahbazker@imgtec.com>
Cc: Raghu Gandham <raghu.gandham@imgtec.com>
Cc: Matthew Fortune <matthew.fortune@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13764/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Complement commit 102cedc3 ("MIPS: microMIPS: Floating point
support.") which introduced microMIPS FPU emulation, but did not adjust
the encoding of the BREAK instruction used to terminate the branch delay
slot emulation frame.  Consequently the execution of any such frame is
indeterminate and, depending on CPU configuration, will result in random
code execution or an offending program being terminated with SIGILL.

This is because the regular MIPS BREAK instruction is encoded with the 0
major and the 0xd minor opcode, however in the microMIPS instruction set
this major/minor opcode pair denotes an encoding reserved for the DSP
ASE.  Instead the microMIPS BREAK instruction is encoded with the 0
major and the 0x7 minor opcode.

Use the correct BREAK encoding for microMIPS FPU emulation then.
Signed-off-by: NMaciej W. Rozycki <macro@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12174/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Define the central place the default FCSR value is set from, initialised
in `cpu_probe'.  Determine the FCSR mask applied to values written to
the register with CTC1 in the full emulation mode and via ptrace(2),
according to the ISA level of processor hardware or the writability of
bits 31:18 if actual FPU hardware is used.

Software may rely on FCSR bits whose functions our emulator does not
implement, so it should not allow them to be set or software may get
confused.  For ptrace(2) it's just sanity.

[ralf@linux-mips.org: Fixed double inclusion of <asm/current.h>.]
Signed-off-by: NMaciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9711/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Rework `process_fpemu_return' and move IEEE 754 exception interpretation
there, from `do_fpe'.  Record the cause bits set in FCSR before they are
cleared and pass them through to `process_fpemu_return' so as to set
`si_code' correctly too for SIGFPE signals sent from emulation rather
than those issued by hardware with the FPE processor exception only.

For simplicity `mipsr2_decoder' assumes `*fcr31' has been preinitialised
and only sets it to anything if an FPU instruction has been emulated,
which in turn is the only case SIGFPE can be issued for here.
Signed-off-by: NMaciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9705/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Delay slot emulation in the FPU emulator is the only kernel user of an
executable stack, it is also very slow.  Add a counter so we can see
how many of these emulations are done.
Signed-off-by: NDavid Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8634/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The use of __this_cpu_inc() requires a fundamental integer type, so
change the type of all the counters to unsigned long, which is the
same width they were before, but not wrapped in local_t.
Signed-off-by: NDavid Daney <david.daney@cavium.com>
Signed-off-by: NChristoph Lameter <cl@linux.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

Sometimes it's useful to let the user, while doing performance research,
know what in the IEEE754 exceptions has caused many times of FP emulation
when running a specific application. This patch adds 5 more files to
/sys/kernel/debug/mips/fpuemustats/, whose filenames begin with "ieee754".
These stats are in addition to the existing cp1ops, cp1xops, errors, loads
and stores, which may not be useful in understanding the reasons of ieee754
exceptions.

[ralf@linux-mips.org: Fixed reject due to other changes to the kernel
FP assist software.]
Signed-off-by: NDeng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Steven.Hill@imgtec.com
Cc: james.hogan@imgtec.com
Patchwork: http://patchwork.linux-mips.org/patch/7044/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add logic needed to do floating point emulation in microMIPS mode.
Signed-off-by: NLeonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Steven J. Hill <Steven. Hill@imgtec.com>

Caused by 38b7827f - no, cpu_local_* was
not unused.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Cc: Christoph Lameter <cl@linux-foundation.org>
Acked-by: NDavid Daney <ddaney@caviumnetworks.com>

On SMP systems, the collection of statistics can cause cache line
bouncing in the lines associated with the counters.  Also there are
races incrementing the counters on multiple CPUs.

To fix both problems, we collect the statistics in per-CPU variables,
and add them up in the debugfs read operation.

As a test I ran the LTP float_bessel test on a 12 CPU Octeon system.

Without CONFIG_DEBUG_FS :             2602 seconds.
With CONFIG_DEBUG_FS:                 2640 seconds.
With non-cpu-local atomic statistics: 14569 seconds.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Cc: linux-mips@linux-mips.org
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Arguably using the address error handler has always been ugly.  But with
processors that handle unaligned loads and stores in hardware the
current mechanism ceases to work so switch it to a BREAK instruction and
allocate break code 514 to the FPU emulator.

Yoichi Yuasa provided a build fix for CONFIG_BUG=n.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NYoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The struct mips_fpu_soft_struct and mips_fpu_hard_struct are
completely same now and the kernel fpu emulator assumes that.  This
patch unifies them to mips_fpu_struct and get rid of mips_fpu_union.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

mips_fpu_emulator_stats cleanup that unnecessary nesting of structs.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

never initialized been initialized anywhere, just saved to and
restored from signal frames so nonsense anyway.  As neat side effect
of being shared between all processors it was also abusable as a
nice covert channel between processes.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!