... to make clear the meaning of the argument.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Acked-by: NLiam Girdwood <liam.r.girdwood@linux.intel.com>
Acked-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

The EQ coefficient binary controls overlapped with the volume controls
for the B4 and B5 volumes, which were controllable from either the
coefficient control or the volume control itself.

This patch adds controls for the mode and moves the coefficient control
to only cover the coefficients.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NRichard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

When writing the patch write to the device asynchronously, allowing better
performance when used with a bus like SPI which supports this by
minimising the need to context switch back to the driver to get the
next bit of data.
Signed-off-by: NMark Brown <broonie@linaro.org>
Reviewed-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>

Signed-off-by: NRichard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

The noise and mic mixer inputs were not connected, do so.
Signed-off-by: NMark Brown <broonie@linaro.org>

The routes linking the widget and the input mux were being added
manually, rather than by the ARIZONA_MUX_ROUTES macro. This patchs adds
the routes to the macro.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

When doing signal activity detection, the only output from the DRC will
often be a GPIO pin. This patch adds a signal activity output that is
activated when a GPIO is configured to output the DRC signal activity
detection.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Certain use cases may require specific DRE settings so expose control
of these.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

All sources and sinks should enable SYSCLK.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Reported-by: NRyo Tsutsui <Ryo.Tsutsui@wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org

Now that we have regular register mapped controls we should be splitting
the control sets for ADSP1 and ADSP2 as the register maps are not
identical. Do that.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Running HPDET while the headphone outputs are enabled can disrupt the
operation of HPDET. In order to avoid this HPDET needs to disable the
headphone outputs and ASoC needs to not enable them while HPDET is
running.

Do the ASoC side of this by storing the enable state in the core driver
structure and only writing to the device if a flag indicating that the
accessory detection side is in a state where it can have the headphone
output stage enabled.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Since ASoC does not yet really have the framework features needed to
support propagating sample rates through the device well yet implement
basic support for the ISRCs equivalent to that we currently have for the
ASRCs. The user can opt for 8kHz or 16kHz as the rate for the DSP blocks
in addition to the main audio rate, these being the primary use cases.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Some system designs have been identified which repurpose portions of the
speaker driver circuits for other functions which will require that they
not be managed using DAPM. Prepare for this by factoring out the creation
of the speaker widgets into the core driver, the widgets will be replaced
by dummy ones when the additional functions are enabled.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Evaluation has identified some performance improvements to the device.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Since we are automatically managing the mutes we may as well also manage
the volume update bits, disabling volume updates while none of the inputs
are active. Since we are doing this we may as well allow the volumes to
ramp together so only enable volume updates once at the end of power up.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch allows the REFCLK to be set directly allowing much greater
flexibility in how the FLLs are configured.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

For optimal performance the inputs should be kept muted until after power
up. Since there are few use cases for muting inputs during capture move
the mutes to automatic control.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The generated defines in the header are pre-shifted.
Reported-by: NHeather Lomond <Heather.Lomond@wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The references used for the noise gates and parameters for their triggering
are configurable, expose that to users.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Though the controls are named as stereo controls in the part the main use
case for the analogue inputs to the WM5102 is mono. Reflect this in the
controls exposed to userspace, providing a series of mono controls rather
than stereo ones.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

CONFIG_HOTPLUG is going away as an option.  As result the __dev*
markings will be going away.

Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Provide a haptics widget for use by the haptics driver and expose the DAPM
context for it.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>