By definition, wait_for_completion_timeout() returns an unsigned value and
therefore, it is not necessary to check if the return value is less than zero
as this is not possible.

This is based on a patch from Jon Hunter <jon-hunter@ti.com>
Changes from his patch
- Declare a long as the wait_for_completion_timeout returns long.

Original patch is
http://git.omapzoom.org/?p=kernel/omap.git;a=commitdiff;h=ea02cece7b0000bc736e60c4188a11aaa74bc6e6Reviewed-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NJon Hunter <jon-hunter@ti.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

Currently in probe
pm_runtime_put(dev->dev);

...
        /* i2c device drivers may be active on return from add_adapter() */
        adap->nr = pdev->id;
        r = i2c_add_numbered_adapter(adap);
        if (r) {
                dev_err(dev->dev, "failure adding adapter\n");
                goto err_free_irq;
        }
...

return 0;

err_free_irq:
        free_irq(dev->irq, dev);
err_unuse_clocks:
        omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, 0);
        pm_runtime_put(dev->dev);

This may access the i2c registers without the clocks in the error cases.
Fix the same by moving the pm_runtime_put after the error check.
Reviewed-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

On OMAP4 we were writing 1 to IRQENABLE_CLR which cleared only
the arbitration lost interrupt. The patch intends to fix the same by writing 0
to the IE register clearing all interrupts.

This is based on the work done by Vikram Pandita <vikram.pandita@ti.com>.

The  changes from the original patch ...
-  Does not use the IRQENABLE_CLR register to clear as it is not mentioned
  to be legacy register IRQENABLE_CLR helps in  atomically
  setting/clearing specific interrupts, instead use the OMAP_I2C_IE_REG as we
  are clearing all interrupts.

Cc: Vikram Pandita <vikram.pandita@ti.com>
Reviewed-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

Currently the i2c driver calls the pm_runtime_enable and never
the disable. This may cause a warning when pm_runtime_enable
checks for the count match.Fix the same by calling
pm_runtime_disable in the error and the remove path.

Cc: Rajendra Nayak <rnayak@ti.com>
Acked-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

The functions omap_i2c_unidle/idle are called from omap_i2c_runtime_resume
and omap_i2c_runtime_suspend which is compiled for CONFIG_PM_RUNTIME.
This patch removes the omap_i2c_unidle/idle functions and folds them
into the runtime callbacks.

This fixes the below warn when CONFIG_PM_RUNTIME is not defined

 CC      arch/arm/mach-omap2/board-ti8168evm.o
drivers/i2c/busses/i2c-omap.c:272: warning: 'omap_i2c_unidle' defined but not used
drivers/i2c/busses/i2c-omap.c:293: warning: 'omap_i2c_idle' defined but not used
  CC      net/ipv4/ip_forward.o
Reviewed-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

CONFIG_OF is not defined for OMAP1 yet and thus the omap1_defconfig build
generate an error for 3.3-rc1.

drivers/i2c/busses/i2c-omap.c: In function 'omap_i2c_probe':
drivers/i2c/busses/i2c-omap.c:1021:26: error: 'omap_i2c_of_match' undeclared (first use in this function)
drivers/i2c/busses/i2c-omap.c:1021:26: note: each undeclared identifier is reported only once for each function it appears in

Wrap omap_i2c_of_match with of_match_ptr() to prevent compilation error in case of OMAP1 build.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add initial DT support to retrieve the frequency using a
DT attribute instead of the pdata pointer if of_node exist.

Add documentation for omap i2c controller binding.

Based on original patches from Manju and Grant.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Reviewed-by: NRob Herring <rob.herring@calxeda.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NKevin Hilman <khilman@ti.com>

On OMAP4 OMAP_I2C_STAT_NACK is causing a timeout on the next access.
The isr cleans all flags in OMAP_I2C_CON_REG by setting OMAP_I2C_CON_STP
OMAP_I2C_CON_STP is also set in omap_i2c_xfer_msg on the last message.

According to the TI TSR the sequence for OMAP_I2C_STAT_NACK and
OMAP_I2C_STAT_AL are nearly the same.
Removing the OMAP_I2C_CON_STP part in the isr fix the problem.
Tested on OMAP4430 and OMAP3530 (here NACK was not a problem)
Fixes also booting on 2430sdp.
Signed-off-by: NJan Weitzel <j.weitzel@phytec.de>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

Correct OMAP_I2C_SYSC_REG offset in omap4 register map.
Offset 0x20 is reserved and OMAP_I2C_SYSC_REG has 0x10 as offset.
Signed-off-by: NAlexander Aring <a.aring@phytec.de>
[khilman@ti.com: minor changelog edits]
Cc: stable@vger.kernel.org
Signed-off-by: NKevin Hilman <khilman@ti.com>

Currently the fifo depth is set to zero for OMAP4 which disables
the FIFO usage. This patch enables the FIFO usage for I2C transactions
on OMAP4 also.

Tested on omap4430 and 3430.
Tested-and-Reported-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Current usage of runtime PM is not quite correct.  The actual
idle/unidle of the I2C hardware should not happen until the runtime PM
callbacks are called.  Therefore, change omap_i2c_[un]idle() functions
to only be called from the runtime PM callbacks (when usage count
transitions to/from zero.)

Also, the runtime PM core does usage counting and replaces
functionality currently managed by the dev->idle flag.  Remove usage
of dev->idle in favor of using runtime PM, and checking status using
pm_runtime_suspended().
Signed-off-by: NKevin Hilman <khilman@ti.com>

A pointer to the struct device associated with the i2c device is
already kept in the struct omap_i2c_dev, so use omap_i2c_device to
find the pointer to struct device.
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

Currently for OMAP4 the I2C_WE is not programmed.
This patch enables the programming for OMAP4.

This patch fixes a bad conflict resolution.
This effectively restores the following commit

Commit 120bdaa4[i2c-omap: Program I2C_WE on OMAP4 to enable i2c wakeup]

which got changed by

Commit a3a7acbc[I2C: OMAP2+: address confused probed version naming]
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Reported-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

The IP version is prepended to the existing printed probed
version as an "epoch" version.

Cc: patches@linaro.org
Reported-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NAndy Green <andy.green@linaro.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Acked-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NKevin Hilman <khilman@ti.com>

This patch eliminates all cpu_...() tests from the OMAP I2C driver.

Instead, it uses the functionality flags in the platform data to make
the decisions about product variations the driver needs to handle.

Cc: patches@linaro.org
Reported-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NAndy Green <andy.green@linaro.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Acked-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NKevin Hilman <khilman@ti.com>

The driver reflects the confusion that probed I2C revision
from the hardware of 0x40 means it is on an OMAP4430.

However, you will probe the same 0x40 ID on an OMAP3530.  So
this patch changes the name to reflect that.

It also clarifies that the original name OMAP_I2C_REV_2 is
referring to some ancient OMAP1 revision number, not to be
confused with the IP revisions this patch series introduces.

Similarly the term "rev" is used in the ancient OMAP1 ISR,
the term is changed to use omap1 instead.

Cc: patches@linaro.org
Reported-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NAndy Green <andy.green@linaro.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Acked-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NKevin Hilman <khilman@ti.com>

This solves the main problem the patch series is about.  Prior
to this patch on OMAP3530 the driver wrongly interprets the I2C
peripheral unit's own reported revision as meaning it is running
on an IP V2 device and must use the extended registers.

In fact OMAP3530 is IP V1 with the smaller register set, the
reason for the confusion is that the hardware does in fact report
having the same IP revision index as is found on an OMAP4430,
which really is IP V2 and has the extended registers.

This corrects the test for which registers to use so that it
decides using hwmod knowledge found in the platform_data.

Cc: patches@linaro.org
Reported-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NAndy Green <andy.green@linaro.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Acked-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NKevin Hilman <khilman@ti.com>

Change the register map names to reflect the IP revision they
are representing, and use the platform_data IP revision index
to select between them at init time.

Eliminates 1 of 17 cpu_...() calls in the driver.

Cc: patches@linaro.org
Reported-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NAndy Green <andy.green@linaro.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Acked-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NKevin Hilman <khilman@ti.com>

The OMAP I2C driver dynamically chooses between two register sets of
differing sizes depending on the cpu type it finds itself on.

It has been observed that the existing code references non-existing
registers on OMAP3530, because while it correctly chose the smaller
register layout based on cpu type, the code uses the probed register
ID to decide if to execute code referencing an extra register, and
both register layout devices on OMAP3530 and OMAP4430 report the same
probed ID of 0x40.

This patch changes the extended register names only found on IP V2
of the I2C peripheral unit accordingly to help show up errors in usage.

Cc: patches@linaro.org
Reported-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NAndy Green <andy.green@linaro.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Acked-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NKevin Hilman <khilman@ti.com>

This reverts commit adf6e079.

Remove system PM methods which can race with runtime PM methods.

Also, as of v3.1, the PM domain level code for OMAP handles device
power state transistions automatically for devices, so drivers no
longer need to specifically call the bus/pm_domain methods themselves.
Signed-off-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Make sure that the 'static' keywork is at the beginning of declaration
for drivers/i2c/busses/i2c-omap.c

This gets rid of warnings like
  warning: ‘static’ is not at beginning of declaration
when building with -Wold-style-declaration (and/or -Wextra which also
enables it).
Signed-off-by: NJesper Juhl <jj@chaosbits.net>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

For the I2C module to be wakeup capable, programming I2C_WE register (which
was skipped for OMAP4430) is needed even on OMAP4.

This fixes i2c controller timeouts which were seen recently with the static
dependency being cleared between MPU and L4PER clockdomains.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
[ben-linux@fluff.org: re-flowed description]
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Fixup the whitespace error noticed in cb527edeSigned-off-by: NBen Dooks <ben-linux@fluff.org>

This errata occurs when the ARDY interrupt generation is enabled.
At the begining of every new transaction the ARDY interrupt is cleared.

On continuous i2c transactions where after clearing the ARDY bit from
I2C_STAT register (clearing the interrupt), the IRQ line is reasserted and the
I2C_STAT[ARDY] bit set again on 1. In fact, the ARDY status bit is not cleared
at the write access to I2C_STAT[ARDY] and only the IRQ line is deasserted and
then reasserted. This is not captured in the usual errata documents.

The workaround is to have a double clear of ARDY status in irq handler.
Signed-off-by: NRichard woodruff <r-woodruff2@ti.com>
Signed-off-by: NKeerthy <j-keerthy@ti.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

fix the build break when !CONFIG_SUSPEND

drivers/i2c/busses/i2c-omap.c:1173: error: lvalue required as unary '&' operand
make[3]: *** [drivers/i2c/busses/i2c-omap.o] Error 1
make[2]: *** [drivers/i2c/busses] Error 2
make[1]: *** [drivers/i2c] Error 2
make: *** [drivers] Error 2
Signed-off-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

When runtime PM is enabled, each OMAP i2c device is suspended after
each i2c xfer.  However, there are two cases when the static suspend
methods must be used to ensure the devices are suspended:

1) runtime PM is disabled, either at compile time or dynamically
    via /sys/devices/.../power/control.
2) an i2c client driver uses i2c during it's suspend callback, thus
   leaving the i2c driver active (NOTE: runtime suspend transitions are
   disabled during system suspend, so i2c activity during system
   suspend will runtime resume the device, but not runtime (re)suspend it.)

Since the actual work to suspend the device is handled by the
subsytem, call the bus methods to take care of it.

NOTE: This takes care of a known suspend problem on OMAP3 where the
TWL RTC driver does i2c xfers during its suspend path leaving the i2c
driver in an active state (since runtime suspend transistions are
disabled.)
Signed-off-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Ordinary I2C read consist of two messages. First a write operation
to tell register address and then read operation to get data.
CPU wake up latency is set and removed twice in read case.
Set latency requirement before the message processing loop
and remove the requirement after the loop to remove latency
adjustment operations between the messages.
Signed-off-by: NSamu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>
Acked-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

The convention for omap device naming is omap_XXX.

Rename the device and driver name in order to stick
to this naming convention.

Change device name in clock nodes as well.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Ben Dooks <ben-i2c@fluff.org>
Acked-by: NPaul Walmsley <paul@pwsan.com>
Acked-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch converts the i2c driver to use PM runtime apis
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Jean Delvare <khali@linux-fr.org>
Acked-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

If the i2c bus receives an interrupt with both BB (bus busy) and
ARDY (register access ready) statuses set during the tranfer of the last message
the bus was put to idle while still busy.

This caused bus to timeout.
Signed-off-by: NMathias Nyman <mathias.nyman@nokia.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Clean up existing Errata 1p153 handling to use generic
errata handling mechanism through dev flag.
Signed-off-by: NManjunatha GK <manjugk@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Alexander Shishkin <virtuoso@slind.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

While waiting for completion of the i2c transfer, the
MPU could hit OFF mode and cause several msecs of
delay that made i2c transfers fail more often. The
extra delays and subsequent re-trys cause i2c clocks
to be active more often. This has also an negative
effect on power consumption.

Created a mechanism for passing and using the
constraint setting function in driver code. The used
mpu wake up latency constraints are now set individually
per bus, and they are calculated based on clock rate
and fifo size.

Thanks to Jarkko Nikula, Moiz Sonasath, Paul Walmsley,
and Nishanth Menon for tuning out the details of
this patch.

Updates by Kevin as requested by Tony:

- Remove omap_set_i2c_constraint_func() in favor of conditionally
  adding the flag in omap_i2c_add_bus() in order to keep all the OMAP
  conditional checking in a single location.
- Update set_mpu_wkup_lat prototypes to match OMAP PM layer so
  OMAP PM function can be used directly in pdata.

Cc: Moiz Sonasath <m-sonasath@ti.com>
Cc: Jarkko Nikula <jhnikula@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: NKalle Jokiniemi <kalle.jokiniemi@digia.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Under certain rare conditions, I2C_STAT[13].RDR bit may be set
and the corresponding interrupt fire, even there is no data in
the receive FIFO, or the I2C data transfer is still ongoing.
These spurious RDR events must be ignored by the software.

This patch handles and ignores RDR spurious interrupts.

The below sequence is required in interrupt handler for
handling this errata:
1. If RDR is set to 1, clear RDR
2. Read I2C status register and check for BusBusy bit. If BusBusy
bit is set, skip remaining steps.
3. If BusBusy bit is not set, perform read operation on I2C status
register.
4. If RDR is set, clear the same. Check RDR again and clear if it sets
RDR bit again.
5. Perform I2C Data Read operation N number of times(where N is value
read from the register BUFSTAT-RXSTAT bit fields).

Note:
This errata is not applicable for omap2420 and omap4.
It is applicable for:
1. omap2430
2. omap34xx(including omap3630).
Signed-off-by: NManjunatha GK <manjugk@ti.com>
Cc: Hema Kalliguddi <hemahk@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Aaro Koskinen <Aaro.Koskinen@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

This patch is rebased version of earlier post to add I2C
driver support to OMAP4 platform. On OMAP4, all
I2C register address offsets are changed from OMAP1/2/3 I2C.
In order to not have #ifdef's at various places in code,
as well as to support multi-OMAP build, an array is created
to hold the register addresses with it's offset.

This patch was submitted, reviewed and acked on mailing list
already. For more details refer below link
http://www.mail-archive.com/linux-i2c@vger.kernel.org/msg02281.html

This updated verion has a depedancy on "Add support for 16-bit registers"
posted on linux-omap. Below is the patch-works link for the same

http://patchwork.kernel.org/patch/72295/Signed-off-by: NSyed Rafiuddin <rafiuddin.syed@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>
Reviewed-by: NPaul Walmsley <paul@pwsan.com>
Cc: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

The errata 1.153 workaround is busy waiting on XUDF bit in interrupt
context, which may lead to kernel hangs. The problem can be reproduced
by running the bus with wrong (too high) speed.
Signed-off-by: NAlexander Shishkin <virtuoso@slind.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

This is to avoid insanely long lines and levels of indentation.
Signed-off-by: NAlexander Shishkin <virtuoso@slind.org>
Cc: Nishant Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Commit d84d3ea3 added register shift to allow
also 16-bit register access. However, omap_i2c_unidle() is called before these
are set which causes the following OOPS:

    Unhandled fault: alignment exception (0x801) at 0xfa070009
    Internal error: : 801 [#1]
    last sysfs file:
    Modules linked in:
    CPU: 0    Not tainted  (2.6.34-rc2-00052-gae6be51e #3)
    PC is at omap_i2c_unidle+0x44/0x138
    LR is at trace_hardirqs_on_caller+0x158/0x18c
    pc : [<c01cd2c4>]    lr : [<c00743f8>]    psr: 20000013
    sp : cfc2bf10  ip : 00000009  fp : 00000000
    r10: 00000000  r9 : 00000000  r8 : c0378560
    r7 : c0378b88  r6 : c0378558  r5 : cfcadc00  r4 : cfcadc00
    r3 : 00000009  r2 : fa070000  r1 : 00000000  r0 : 00000000
    Flags: nzCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment kernel
    Control: 10c5387f  Table: 80004019  DAC: 00000017
    Process swapper (pid: 1, stack limit = 0xcfc2a2e8)
    Stack: (0xcfc2bf10 to 0xcfc2c000)
    bf00:                                     c0372cf8 c027225c 00000000 c0a69678
    bf20: cfc3e508 c0500898 c0378560 c0378560 c0500898 cfcac8c0 c04fc280 c017d4f4
    bf40: c0378560 c017c63c c0378560 c0378594 c0500898 cfcac8c0 c04fc280 c017c754
    bf60: 00000000 c017c6f4 c0500898 c017beac cfc16a5c cfc3fd94 c0023448 c0500898
    bf80: c0500898 c017b7d4 c032dc7f 00000093 cfc28d40 c0023448 00000000 c0500898
    bfa0: 00000000 00000000 00000000 c017ca48 c0023448 00000000 c001d274 00000000
    bfc0: 00000000 c002b344 00000031 00000000 00000000 00000192 00000000 c0023448
    bfe0: 00000000 00000000 00000000 c0008578 00000000 c002c304 ffdfffff ffffffff
    [<c01cd2c4>] (omap_i2c_unidle+0x44/0x138) from [<c027225c>] (omap_i2c_probe+0x1a4/0x398)
    [<c027225c>] (omap_i2c_probe+0x1a4/0x398) from [<c017d4f4>] (platform_drv_probe+0x18/0x1c)
    [<c017d4f4>] (platform_drv_probe+0x18/0x1c) from [<c017c63c>] (driver_probe_device+0xc0/0x178)
    [<c017c63c>] (driver_probe_device+0xc0/0x178) from [<c017c754>] (__driver_attach+0x60/0x84)
    [<c017c754>] (__driver_attach+0x60/0x84) from [<c017beac>] (bus_for_each_dev+0x44/0x74)
    [<c017beac>] (bus_for_each_dev+0x44/0x74) from [<c017b7d4>] (bus_add_driver+0x9c/0x218)
    [<c017b7d4>] (bus_add_driver+0x9c/0x218) from [<c017ca48>] (driver_register+0xa8/0x130)
    [<c017ca48>] (driver_register+0xa8/0x130) from [<c002b344>] (do_one_initcall+0x5c/0x1b8)
    [<c002b344>] (do_one_initcall+0x5c/0x1b8) from [<c0008578>] (kernel_init+0x90/0x144)
    [<c0008578>] (kernel_init+0x90/0x144) from [<c002c304>] (kernel_thread_exit+0x0/0x8)
    Code: e5942004 e3a0c009 e1a0331c e3a01000 (e18210b3)
    ---[ end trace 1b75b31a2719ed1c ]---

This patch moves register shift setting before any register accesses are done.
Signed-off-by: NMika Westerberg <ext-mika.1.westerberg@nokia.com>
Cc: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h

percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files.  percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.

percpu.h -> slab.h dependency is about to be removed.  Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability.  As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.

  http://userweb.kernel.org/~tj/misc/slabh-sweep.py

The script does the followings.

* Scan files for gfp and slab usages and update includes such that
  only the necessary includes are there.  ie. if only gfp is used,
  gfp.h, if slab is used, slab.h.

* When the script inserts a new include, it looks at the include
  blocks and try to put the new include such that its order conforms
  to its surrounding.  It's put in the include block which contains
  core kernel includes, in the same order that the rest are ordered -
  alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
  doesn't seem to be any matching order.

* If the script can't find a place to put a new include (mostly
  because the file doesn't have fitting include block), it prints out
  an error message indicating which .h file needs to be added to the
  file.

The conversion was done in the following steps.

1. The initial automatic conversion of all .c files updated slightly
   over 4000 files, deleting around 700 includes and adding ~480 gfp.h
   and ~3000 slab.h inclusions.  The script emitted errors for ~400
   files.

2. Each error was manually checked.  Some didn't need the inclusion,
   some needed manual addition while adding it to implementation .h or
   embedding .c file was more appropriate for others.  This step added
   inclusions to around 150 files.

3. The script was run again and the output was compared to the edits
   from #2 to make sure no file was left behind.

4. Several build tests were done and a couple of problems were fixed.
   e.g. lib/decompress_*.c used malloc/free() wrappers around slab
   APIs requiring slab.h to be added manually.

5. The script was run on all .h files but without automatically
   editing them as sprinkling gfp.h and slab.h inclusions around .h
   files could easily lead to inclusion dependency hell.  Most gfp.h
   inclusion directives were ignored as stuff from gfp.h was usually
   wildly available and often used in preprocessor macros.  Each
   slab.h inclusion directive was examined and added manually as
   necessary.

6. percpu.h was updated not to include slab.h.

7. Build test were done on the following configurations and failures
   were fixed.  CONFIG_GCOV_KERNEL was turned off for all tests (as my
   distributed build env didn't work with gcov compiles) and a few
   more options had to be turned off depending on archs to make things
   build (like ipr on powerpc/64 which failed due to missing writeq).

   * x86 and x86_64 UP and SMP allmodconfig and a custom test config.
   * powerpc and powerpc64 SMP allmodconfig
   * sparc and sparc64 SMP allmodconfig
   * ia64 SMP allmodconfig
   * s390 SMP allmodconfig
   * alpha SMP allmodconfig
   * um on x86_64 SMP allmodconfig

8. percpu.h modifications were reverted so that it could be applied as
   a separate patch and serve as bisection point.

Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: NTejun Heo <tj@kernel.org>
Guess-its-ok-by: NChristoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>

A pointer to omap_i2c_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded.  Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.

An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Kalle Jokiniemi <ext-kalle.jokiniemi@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: chandra shekhar <x0044955@ti.com>
Cc: Jason P Marini <jason.marini@gmail.com>
Cc: Syed Mohammed Khasim  <x0khasim@ti.com>
Cc: Jarkko Nikula <jarkko.nikula@nokia.com>
Cc: Juha Yrjola <juha.yrjola@solidboot.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The current i2c-omap driver is set up for 32-bit registers, which
corresponds to most OMAP devices.  However, OMAP730/850 based
devices use a 16-bit register size.

This change modifies the driver to perform a runtime CPU type check
to determine the register sizes, and uses a bit shift of either 1
or 2 bits to compute the proper register sizes for all registers.
Signed-off-by: NCory Maccarrone <darkstar6262@gmail.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>