Skip to content

cloud-kernel
cloud-kernel

openanolis / cloud-kernel
1 年多 前同步成功

通知 163
Star 36
Fork 7
cloud-kernel
cloud-kernel
切换分支/标签
  1. 18 8月, 2017 1 次提交
  3. 25 7月, 2017 1 次提交
  5. 18 5月, 2017 2 次提交
    • T
      Bluetooth: hci_nokia: select BT_HCIUART_H4 · c42c88e6
      由 Tobias Regnery 提交于 
      We see the following build failure with CONFIG_BT_HCIUART_NOKIA=y and
CONFIG_BT_HCIUART_H4=n:

drivers/bluetooth/hci_nokia.c: In function 'nokia_recv':
drivers/bluetooth/hci_nokia.c:644:18: error: implicit declaration of function 'h4_recv_buf' [-Werror=implicit-function-declaration]
...

Fix this by selecting the BT_HCIUART_H4 symbol like all the other users
of the protocoll.

Fixes: 7bb31868 ("Bluetooth: add nokia driver")
Signed-off-by: NTobias Regnery <tobias.regnery@gmail.com>
Reviewed-by: NSebastian Reichel <sre@kernel.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
      c42c88e6
    • T
      Bluetooth: hci_uart: fix kconfig dependency · 76c4969f
      由 Tobias Regnery 提交于 
      We see the following link error with CONFIG_BT_HCIUART=y,
CONFIG_BT_HCIUART_LL=y and CONFIG_SERIAL_DEV_BUS=m:

drivers/built-in.o: In function 'll_close':
supp.c:(.text+0x55add4): undefined reference to 'serdev_device_close'
supp.c:(.text+0x55add4): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol 'serdev_device_close'
drivers/built-in.o: In function 'll_open':
supp.c:(.text+0x55aed0): undefined reference to 'serdev_device_open'
supp.c:(.text+0x55aed0): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol 'serdev_device_open'
drivers/built-in.o: In function `hci_ti_probe':
supp.c:(.text+0x55b00c): undefined reference to 'hci_uart_register_device'
supp.c:(.text+0x55b00c): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol 'hci_uart_register_device'
drivers/built-in.o: In function `ll_setup':
supp.c:(.text+0x55b08c): undefined reference to 'serdev_device_set_flow_control'
supp.c:(.text+0x55b08c): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol 'serdev_device_set_flow_control'
supp.c:(.text+0x55b324): undefined reference to 'serdev_device_set_baudrate'
supp.c:(.text+0x55b324): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol 'serdev_device_set_baudrate'
drivers/built-in.o: In function 'll_init':
supp.c:(.init.text+0x1b508): undefined reference to '__serdev_device_driver_register'
supp.c:(.init.text+0x1b508): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol '__serdev_device_driver_register'

Fix this by dependig BT_HCIUART_LL on the BT_HCIUART_SERDEV symbol.
This implies a dependency on BT_HCIUART and hci_ll.c is only compiled in
if SERIAl_DEV_BUS is built in or SERIAL_DEV_BUS and BT_HCIUART are
modules.

Fixes: 37180552 ("bluetooth: hci_uart: add LL protocol serdev driver support")
Signed-off-by: NTobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
      76c4969f
  7. 22 4月, 2017 1 次提交
    • A
      Bluetooth: try to improve CONFIG_SERIAL_DEV_BUS dependency · 1fb78fb6
      由 Arnd Bergmann 提交于 
      With CONFIG_SERIAL_DEV_BUS=m, the hci_serdev.o file does not actually
get built into hci_uart.o as the Makefile doesn't pick it up, leading
to a link error with anything referring to it:

ERROR: "hci_uart_register_device" [drivers/bluetooth/hci_nokia.ko] undefined!
scripts/Makefile.modpost:91: recipe for target '__modpost' failed

Changing this in the Makefile would cause another problem when
hci_uart itself is built-in and cannot reference symbols from the
serdev module.

This tries to address both problems by introducing a new hidden
Kconfig symbol that controls both the compilation of hci_serdev.o
and whether the Nokia driver can be selected. This seems to address
the problem for me, though there might be a better way to do it.

Fixes: 7bb31868 ("Bluetooth: add nokia driver")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
      1fb78fb6
  9. 13 4月, 2017 1 次提交
  11. 29 3月, 2017 1 次提交
  13. 23 3月, 2017 1 次提交
  15. 17 2月, 2017 1 次提交
  17. 20 9月, 2016 3 次提交
  19. 24 2月, 2016 1 次提交
  21. 21 10月, 2015 2 次提交
    • A
      Bluetooth: bpa10x: fix BT_HCIUART dependency · 7841d06e
      由 Arnd Bergmann 提交于 
      The change to bpa10x to use the h4_recv_buf helper added a dependency
on BT_HCIUART. This was incorrectly added to Kconfig by adding a
'select' statement, which now in turn causes build failures
when CONFIG_TTY is not set:

warning: (BT_HCIBPA10X) selects BT_HCIUART which has unmet direct dependencies (NET && BT && TTY)
vers/built-in.o: In function `hci_uart_tty_receive':
fpga-mgr.c:(.text+0x282824): undefined reference to `tty_unthrottle'
drivers/built-in.o: In function `hci_uart_tty_ioctl':
fpga-mgr.c:(.text+0x282aa0): undefined reference to `n_tty_ioctl_helper'
drivers/built-in.o: In function `hci_uart_flush':

This replaces the 'select BT_HCIUART' dependency with 'depends on', which
does not have this kind of problem. Alternatively, one could add 'depends
on TTY', but avoiding 'select' on user-visible options is generally the
preferred choice as that does not introduce the potential for dependency
loops or incomplete dependency chains.

Fixes: 91489919 ("Bluetooth: bpa10x: Fix missing BT_HCIUART dependency")
Fixes: 943cc592 ("Bluetooth: bpa10x: Use h4_recv_buf helper for frame reassembly")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
      7841d06e
    • M
      Bluetooth: bpa10x: Fix missing BT_HCIUART dependency · 91489919
      由 Marcel Holtmann 提交于 
      Selecting just BT_HCIUART_H4 is not enough and it also needs to select
BT_HCIUART to avoid this warning:

warning: (BT_HCIBPA10X) selects BT_HCIUART_H4 which has unmet direct
dependencies (NET && BT && BT_HCIUART)
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
      91489919
  23. 08 10月, 2015 1 次提交
  25. 04 10月, 2015 1 次提交
    • L
      Bluetooth: btintel: Add iBT register access over HCI support · d06f107b
      由 Loic Poulain 提交于 
      Add regmap ibt to support Intel Bluetooth silicon register access
over HCI. Intel BT/FM combo chip allows to read/write some registers
(e.g. FM registers) via its HCI interface.

Read/Write operations are performed via a HCI transaction composed of
a HCI command (host->controller) followed by a HCI command complete
event (controller->host). Read/Write Command opcodes can be specified
to the regmap init function.
We define data formats which are intel/vendor specific.

Register Read/Write HCI command payload (Host):
Field: | REG ADDR | MODE | DATA_LEN | DATA... |
size:  |   32b    |  8b  |    8b    |  8b*    |

Register Read HCI command complete event payload (Controller):
Field: | CMD STATUS | REG ADDR | DATA... |
size:  |     8b     |   32b    |  8b*    |

Register Write HCI command complete event payload (Controller):
Field: | CMD_STATUS |
size:  |     8b     |

Since this payload is HCI encapsulated, Little Endian byte order is
used.

Write/Read Example:

If we write 0x0000002a at address 0x00008c04, with opcode_write 0xfc5d,
The resulting transaction is (btmon trace):

< HCI Command (0x3f|0x005d) plen 10 [hci0]
        04 8c 00 00 02 04 2a 00 00 00
> HCI Event (0x0e) plen 4
      Unknown (0x3f|0x005d) ncmd 1
        00

Then, if we read the same register with opcode_read 0xfc5e:

< HCI Command (0x3f|0x005e) plen 6 [hci0]
        04 8c 00 00 02 04
> HCI Event (0x0e) plen 12 [hci0]
      Unknown (0x3f|0x005e) ncmd 1
        00 04 8c 00 00 2a 00 00 00
Signed-off-by: NLoic Poulain <loic.poulain@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
      d06f107b
  27. 22 9月, 2015 1 次提交
  29. 11 8月, 2015 2 次提交
  31. 23 7月, 2015 1 次提交
  33. 14 5月, 2015 1 次提交
  35. 08 4月, 2015 12 次提交
  37. 04 12月, 2014 1 次提交
    • X
      Bluetooth: btmrvl add firmware dump support · dc759613
      由 Xinming Hu 提交于 
      This patch adds firmware dump support for marvell
bluetooth chipset. Currently only SD8897 is supported.
This is implemented based on dev_coredump, a new mechnism
introduced in kernel 3.18rc3

Firmware dump can be trigger by
echo 1 > /sys/kernel/debug/bluetooth/hci*/config/fw_dump
and when the dump operation is completed, data can be read by
cat /sys/class/devcoredump/devcd*/data

We have prepared following script to divide fw memory
dump data into multiple files based on memory type.

 [root]# cat btmrvl_split_dump_data.sh
 #!/bin/bash
 # usage: ./btmrvl_split_dump_data.sh dump_data

 fw_dump_data=$1

 mem_type="ITCM DTCM SQRAM APU CIU ICU MAC EXT7 EXT8 EXT9 EXT10 EXT11 EXT12 EXT13 EXTLAST"

 for name in ${mem_type[@]}
 do
         sed -n "/Start dump $name/,/End dump/p" $fw_dump_data  > tmp.$name.log
         if [ ! -s tmp.$name.log ]
                 then
                         rm -rf tmp.$name.log
                 else
                         # Remove the describle info "Start dump" and "End dump"
                         sed '1d' tmp.$name.log | sed '$d' > /data/$name.log
                         if [ -s /data/$name.log ]
                         then
                                 echo "generate /data/$name.log"
                         else
                                 sed '1d' tmp.$name.log | sed '$d' > /var/$name.log
                                 echo "generate /var/$name.log"
                         fi
                         rm -rf tmp.$name.log
         fi
 done
Signed-off-by: NXinming Hu <huxm@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Reviewed-by: NJohannes Berg <johannes@sipsolutions.net>
Reviewed-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
      dc759613
  39. 30 9月, 2014 1 次提交
  41. 03 7月, 2014 1 次提交
  43. 10 3月, 2014 1 次提交
  45. 12 6月, 2013 1 次提交
  47. 19 1月, 2013 1 次提交
    • J
      tty: Added a CONFIG_TTY option to allow removal of TTY · 4f73bc4d
      由 Joe Millenbach 提交于 
      The option allows you to remove TTY and compile without errors. This
saves space on systems that won't support TTY interfaces anyway.
bloat-o-meter output is below.

The bulk of this patch consists of Kconfig changes adding "depends on
TTY" to various serial devices and similar drivers that require the TTY
layer.  Ideally, these dependencies would occur on a common intermediate
symbol such as SERIO, but most drivers "select SERIO" rather than
"depends on SERIO", and "select" does not respect dependencies.

bloat-o-meter output comparing our previous minimal to new minimal by
removing TTY.  The list is filtered to not show removed entries with awk
'$3 != "-"' as the list was very long.

add/remove: 0/226 grow/shrink: 2/14 up/down: 6/-35356 (-35350)
function                                     old     new   delta
chr_dev_init                                 166     170      +4
allow_signal                                  80      82      +2
static.__warned                              143     142      -1
disallow_signal                               63      62      -1
__set_special_pids                            95      94      -1
unregister_console                           126     121      -5
start_kernel                                 546     541      -5
register_console                             593     588      -5
copy_from_user                                45      40      -5
sys_setsid                                   128     120      -8
sys_vhangup                                   32      19     -13
do_exit                                     1543    1526     -17
bitmap_zero                                   60      40     -20
arch_local_irq_save                          137     117     -20
release_task                                 674     652     -22
static.spin_unlock_irqrestore                308     260     -48
Signed-off-by: NJoe Millenbach <jmillenbach@gmail.com>
Reviewed-by: NJamey Sharp <jamey@minilop.net>
Reviewed-by: NJosh Triplett <josh@joshtriplett.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      4f73bc4d