A driver must wait 100us before attempting an MMIO operation
to the RISC after a soft-reset has been initiated.  A
similar delay was needed with earlier ISPs.

Note: a PCI config-space read is used to flush the MMIO
write to the ISP, since the ISP's state machines are unable
to respond to any MMIO read during the reset process.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Correct issue where abort I/O command was not being issued
when the loop-state was down.
Signed-off-by: NRavi Anand <ravi.anand@qlogic.com>
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

When mulitple initiators are coming up in an FCAL topology.
Signed-off-by: NRavi Anand <ravi.anand@qlogic.com>
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

On MMIO relaxed-order platforms, it is possible for the
proper delay during NVRAM access to begin before the request
passes through the PCI bus (via a MMIO write) to the ISP.
Thus, causing a subsequent read to the NVRAM part to fail.
Add a MMIO read, after the MMIO write to insure any posted
writes are flushed.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Received from Mark Salyzyn.

The return data from a read capacity 16 needs to have RTO_EN and PROT_EN
zeroed out.
Signed-off-by: NMark Haverkamp <markh@osdl.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

sd_issue_flush() is called from atomic context so we can't use the
semaphore based routines to get a reference to the scsi_disk.  Assume
something else already got the reference so we can safely use it.
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

The problem is that scsi_run_queue is called from scsi_next_command()
after doing a scsi_put_command.  If the command was the only thing
holding the reference on the scsi_device then the resulting device put
will tear down the block queue.  Fix this by taking a reference to the
device and holding it around scsi_run_queue()
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: NRam Pai <linuxram@us.ibm.com>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

An unbindable mount does not forward or receive propagation.  Also
unbindable mount disallows bind mounts.  The semantics is as follows.

Bind semantics:
  It is invalid to bind mount an unbindable mount.

Move semantics:
  It is invalid to move an unbindable mount under shared mount.

Clone-namespace semantics:
  If a mount is unbindable in the parent namespace, the corresponding
  cloned mount in the child namespace becomes unbindable too.  Note:
  there is subtle difference, unbindable mounts cannot be bind mounted
  but can be cloned during clone-namespace.
Signed-off-by: NRam Pai <linuxram@us.ibm.com>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This makes bind, rbind, move, clone namespace and umount operations
aware of the semantics of slave mount (see Documentation/sharedsubtree.txt
in the last patch of the series for detailed description).
Signed-off-by: NRam Pai <linuxram@us.ibm.com>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

A slave mount always has a master mount from which it receives
mount/umount events.  Unlike shared mount the event propagation does not
flow from the slave mount to the master.
Signed-off-by: NRam Pai <linuxram@us.ibm.com>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

An unmount of a mount creates a umount event on the parent.  If the
parent is a shared mount, it gets propagated to all mounts in the peer
group.
Signed-off-by: NRam Pai <linuxram@us.ibm.com>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Implement handling of mount --move in presense of shared mounts (see
Documentation/sharedsubtree.txt in the end of patch series for detailed
description).
Signed-off-by: NRam Pai <linuxram@us.ibm.com>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Implement handling of MS_BIND in presense of shared mounts (see
Documentation/sharedsubtree.txt in the end of patch series for detailed
description).
Signed-off-by: NRam Pai <linuxram@us.ibm.com>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This creates shared mounts.  A shared mount when bind-mounted to some
mountpoint, propagates mount/umount events to each other.  All the
shared mounts that propagate events to each other belong to the same
peer-group.
Signed-off-by: NRam Pai <linuxram@us.ibm.com>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

A private mount does not forward or receive propagation.  This patch
provides user the ability to convert any mount to private.
Signed-off-by: NRam Pai <linuxram@us.ibm.com>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This removes the per-namespace semaphore in favor of a global semaphore.
This can have an effect on namespace scalability.
Signed-off-by: NMiklos Szeredi <miklos@szeredi.hu>
Signed-off-by: NRam Pai <linuxram@us.ibm.com>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

 - clean up the ugliness in may_umount_tree()

 - fix a bug in do_loopback().  after cloning a tree, do_loopback()
   unlinks only the topmost mount of the cloned tree, leaving behind the
   children mounts on their corresponding expiry list.
Signed-off-by: NRam Pai <linuxram@us.ibm.com>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

umount is done under the protection of the namespace semaphore.  This
can lead to intresting deadlocks when the last reference to a mount is
released, if filesystem code is in sufficiently nasty state.

This collects all the to-be-released-mounts and releases them after
releasing the namespace semaphore.  That both reduces the time we are
holding namespace semaphore and gets the things more robust.

Idea proposed by Al Viro.
Signed-off-by: NRam Pai <linuxram@us.ibm.com>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Old semantics: graft_tree() grabs a reference on the vfsmount before
returning success.

New one: graft_tree() leaves that to caller.

All the callers of graft_tree() immediately dropped that reference
anyway.  Changing the interface takes care of this unnecessary overhead.

Idea proposed by Al Viro.
Signed-off-by: NRam Pai <linuxram@us.ibm.com>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NRam Pai <linuxram@us.ibm.com>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Allow caller of seq_open() to kmalloc() seq_file + whatever else they
want and set ->private_data to it.  seq_open() will then abstain from
doing allocation itself.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

 - check_mnt() on the source of binding should've been unconditional
   from the very beginning.  My fault - as far I could've trace it,
   that's an old thinko made back in 2001.  Kudos to Miklos for spotting
   it...

   Fixed.

 - code cleaned up.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The way we currently deal with quota and process accounting that might
keep vfsmount busy at umount time is inherently broken; we try to turn
them off just in case (not quite correctly, at that) and

  a) pray umount doesn't fail (otherwise they'll stay turned off)
  b) pray nobody doesn anything funny just as we turn quota off

Moreover, LSM provides hooks for doing the same sort of broken logics.

The proper way to deal with that is to introduce the second kind of
reference to vfsmount.  Semantics:

 - when the last normal reference is dropped, all special ones are
   converted to normal ones and if there had been any, cleanup is done.
 - normal reference can be cloned into a special one
 - special reference can be converted to normal one; that's a no-op if
   we'd already passed the point of no return (i.e.  mntput() had
   converted special references to normal and started cleanup).

The way it works: e.g. starting process accounting converts the vfsmount
reference pinned by the opened file into special one and turns it back
to normal when it gets shut down; acct_auto_close() is done when no
normal references are left.  That way it does *not* obstruct umount(2)
and it silently gets turned off when the last normal reference to
vfsmount is gone.  Which is exactly what we want...

The same should be done by LSM module that holds some internal
references to vfsmount and wants to shut them down on umount - it should
make them special and security_sb_umount_close() will be called exactly
when the last normal reference to vfsmount is gone.

quota handling is even simpler - we don't use normal file IO anymore, so
there's no need to hold vfsmounts at all.  DQUOT_OFF() is done from
deactivate_super(), where it really belongs.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

For some stupid reason I can't explain (brown paper bag is at hand), I
removed the check pfn_valid() in the code that does the icache/dcache
coherency on POWER4 and later. That causes us to eventually try to
access non existing struct page when hashing in IO pages.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This is very simple with it being almost all ppc32 with just a couple
of common defines.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NPaul Mackerras <paulus@samba.org>

This fixes a build error when building the pmac sound driver as a
module for 64-bit powermacs.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NPaul Mackerras <paulus@samba.org>

On Tue, Nov 08, 2005 at 08:12:56AM +1100, Benjamin Herrenschmidt wrote:
> Yes, the MAX_ORDER should be different indeed. But can Kconfig do that ?
> That is have the default value be different based on a Kconfig option ?
> I don't see that ... We may have to do things differently here...

This seems to be done in other parts of the Kconfig file.  Using those
as an example, this should keep the MAX_ORDER block size at 16MB.
Signed-off-by: NMike Kravetz <kravetz@us.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Even though we can enable and disable xmon at runtime now, there are a
few places in the merge tree that call xmon and xmon_printf directly.

In the case below we call die() which will call xmon if it is enabled.

Also remove an unnecessary include of xmon.h in smp.c.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>