This changes mac80211 to pass the burst time to conf_tx in txop
units rather than 0.1msec units. 0.1msec units are only required
by atheros hardware (according to current driver support), all
other drivers do other calculations or require the txop value.
Therefore, it results in fewer calculations and more precision
if we just pass the txop value through to the driver.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Acked-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fixes bandswitching for the new mac80211 band API.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We update the version stamp at this time to distinguish the in-kernel
driver from the out of tree driver. The out of tree driver currently
has version number 1.2.25, but the latest driver code can only be
found in this in-kernel driver.

Having a later version number will reduce confusion between the two
versions as we transition from out of tree to in-kernel.
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When we want to go multiqueue, we will need to know the number of
queues the hardware has for registering the master netdev. This
number is only available in ieee80211_register_hw() rather than
ieee80211_alloc_hw(), so defer allocation of the master device to
ieee80211_register_hw().
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix the B43legacy_WARN_ON macro so that it will evaluate expressions.
Signed-off-by: NStefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fixes uploading of the beacon data and writing of the TIM and DTIM offsets.

The patch by Michael Buesch has been ported to b43legacy.
Signed-off-by: NStefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds some definitions for the MAC control register and uses them. This is
basically no functional change.

The patch by Michael Buesch has been ported to b43legacy.
Signed-off-by: NStefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch removes the IWL4965_QOS and IWL3945_QOS defines from Kconfig
file along with all uses of it. These defines were relevant for the
period QoS code was tested to be stable in driver's flows.
Signed-off-by: NRon Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fix allows to control the number of bits that qdiscs book keeping
can be done for with respect to the qdisc pool
Signed-off-by: NRon Rindjunsky <ron.rindjunsky@intel.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds "cooked" monitor mode to mac80211. A monitor interface
in "cooked" mode will see all frames that mac80211 has not used
internally.
Signed-off-by: NMichael Wu <flamingice@sourmilk.net>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There is some duplicated code that sits in front of each function
call to ieee80211_invoke_rx_handlers() that can very well be part
of that function if it gets slightly different arguments.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It doesn't really make sense to have extra pointers to the RX/TX
handler arrays instead of just using the arrays directly, that
also allows us to make them static.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Uninline ieee80211_invoke_rx_handlers to save .text space,
make the code more readable in some places and remove the
"optimisation" that is hit only very few times and unclear
to start with.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Take advantage of the monitor configuration flags now provided by cfg80211.
Signed-off-by: NMichael Wu <flamingice@sourmilk.net>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This allows precise control over what a monitor interface shows.
Signed-off-by: NMichael Wu <flamingice@sourmilk.net>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some instances of RX_DROP mean that the frame was useless,
others mean that the frame should be visible in userspace
on "cooked" monitor interfaces. This patch splits up RX_DROP
and changes each instance appropriately.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The _DROP result will need to be split in the RX path but not
in the TX path, so for preparation split up the type into two
types, one for RX and one for TX. Also make sure (via sparse)
that they cannot be confused.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes compilation breakage caused by 'cfg80211 API for
channels/bitrates' patch.
however it doesn't fix the driver's functional problems caused by that
patch.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix typo in rate initialization. This fixes the WARN_ON()
in net/wireless/util.cpp:83
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add kerneldoc for vendor request functions in rt2x00usb.
Add asynchroneous vendor request function in rt2x00usb.

With the availability of the asynchroneuous vendor request
we can now enable LED class support for rt2500usb and rt73usb.
Since LED handling is not important, it doesn't really matter
if a register call fails (This solution is better then no
LED class support at all).
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Make use of the led triggers provided by mac80211 to control
the led status. This can be enabled through a per-driver
configuration option which will automatically enable the
generic handler in rt2x00lib.

This has been enabled for rt2500usb and rt73usb for the moment
since the led class will call set_brightness in irq context which
will not work correctly with the usb drivers who need to sleep.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

No need to perform the calculation ourselves when
wireless provides a helper function for it.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rt2500usb initialized the SIFS and EIFS without using the
values coming from rt2x000lib. After this is fixed HWMODE_{A,B,G}
is now unused and can be removed in favour of the ieee80211_band
enumeration which could still be usefull later.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Recent changes to the rate structure registration broke rt2x00,
the hw_value was reduced from 32bits to 16bits while rt2x00 used
the full 32bits. However the way rt2x00 used the value was inflexible
and needed to be changed anyway.

This patch creates a array containing information for each rate,
the hw_value passed to mac80211 is the index value for that array
including a field to indicate if short preamble should be enabled.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Author: Adrian Bunk <bunk@kernel.org>

This patch fixes a negative array index spotted by the Coverity checker.

Changes-licensed-under: ISC
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NLuis R. Rodriguez <mcgrof@winlab.rutgers.edu>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Hardware encryption doesn't work yet so lets use software
encryption for now.

Changes-licensed-under: 3-Clause-BSD
Signed-off-by: NLuis R. Rodriguez <mcgrof@winlab.rutgers.edu>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch finishes the port and enables debug as an build option.
This was tested on:

Atheros AR5213A chip found (MAC: 0x59, PHY: 0x43)
RF5112A multiband radio found (0x36)

Note:

For 2 GHz band on the above card I noticed we get negative channel
numbers. Will look into this unless someone beats me to it.

Example out put when loading using:

sudo modprobe ath5k debug=0x00000400

 Band 2 GHz: channels 26, rates 12
  channels:
     1 2412 00c0 0000
     2 2417 00c0 0000
     3 2422 00c0 0000
     4 2427 00c0 0000
     5 2432 00c0 0000
     6 2437 00c0 0000
     7 2442 00c0 0000
     8 2447 00c0 0000
     9 2452 00c0 0000
    10 2457 00c0 0000
    11 2462 00c0 0000
    12 2467 00c0 0000
    13 2472 00c0 0000
    14 2484 00c0 0000
   -498 2512 00c0 0000
   -494 2532 00c0 0000
   -490 2552 00c0 0000
   -486 2572 00c0 0000
   -482 2592 00c0 0000
   -478 2612 00c0 0000
   -474 2632 00c0 0000
   -470 2652 00c0 0000
   -466 2672 00c0 0000
   -462 2692 00c0 0000
   -458 2712 00c0 0000
   -454 2732 00c0 0000
 Band 5 GHz: channels 194, rates 8
  channels:
    27 5135 0140 0000
    28 5140 0140 0000
[... etc ]
   219 6095 0140 0000
   220 6100 0140 0000
  rates:
     60 000b 0000 0000
     90 000f 0000 0000
    120 000a 0000 0000
    180 000e 0000 0000
    240 0009 0000 0000
    360 000d 0000 0000
    480 0008 0000 0000
    540 000c 0000 0000

Changes to base.c, base.h
Changes-licensed-under: 3-Clause-BSD

Changes to debug.c, debug.h
Changes-licensed-under: GPL
Signed-off-by: NLuis R. Rodriguez <mcgrof@winlab.rutgers.edu>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Apologoes, this is a re-post of patch-04, forgot to git-add
our Kconfig... New series (only 2 patches needed fixing, which
I am reposting) can be found here:

http://kernel.org/pub/linux/kernel/people/mcgrof/patches/ath5k/2008-02-04.v2/

Use our own Kconfig file, we'll be expanding this shortly.
Signed-off-by: NLuis R. Rodriguez <mcgrof@winlab.rutgers.edu>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath5k_copy_channels() wasn't setting the channel's band so all
driver channels had a 2GHz band set. Lets set this.

Changes-licensed-under: 3-Clause-BSD
Signed-off-by: NLuis R. Rodriguez <mcgrof@winlab.rutgers.edu>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Cleanup after API changes patch (checkpatch.pl stuff) and on
ath5k_hw_channel() make use of the existing ath5k_channel_ok()
instead of re-implementing the checks again. This was necessary
to make the code cleaner and fit the 80-chars wide limit so
sending it within the same patch.

Finally make a note that we *may* eventually move cap_range stuff
to struct wiphy (band frequency range capabilities). This
information can later be exported to userspace, for example,
and giving it access to mac80211 and drivers in general can come
in handy.

Changes to initvals.c, phy.c
Changes-licensed-under: ISC

Changes to ath5k.h, base.c
Changes-licensed-under: 3-Clause-BSD
Signed-off-by: NLuis R. Rodriguez <mcgrof@winlab.rutgers.edu>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Author: Nick Kossifidis <mickflemm@gmail.com>

Tested on 5211, 5213+5112, 5213A+2112A and it wors fine.

Also i figured out a way to process rate vallue found
on status descriptors, it's still buggy but we are getting
closer (i think it improved stability a little).

Changes to hw.c, initvals.c, phy.c
Changes-licensed-under: ISC

Changes to ath5k.h, base.c, base.h
Changes-licensed-under: 3-Clause-BSD
Acked-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NLuis R. Rodriguez <mcgrof@winlab.rutgers.edu>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When the driver registers a IEEE80211_BAND_2GHZ band,
it can either be 802.11b or 802.11g. But when 802.11b rates
are registered "want" will be 3 (since 4 rates are being registered,
and each of those 4 rates will decrease "want").
Since this is a correct situation, there is no need to trigger
a WARN_ON() for this.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rate_idx is derived from plcp information
Signed-off-by: NMohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

hw_value is being used uninitialized. fix it.
Signed-off-by: NMohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In the rate API patch I accidentally reverted the test for
ERP rates, this fixes it. All rates except 1, 2, 5.5 and 11
MBit are ERP rates, not those.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Merge rate_control_pid_shift_adjust() to rate_control_pid_adjust_rate()
in order to make the learning algorithm aware of constraints on rates. Also
add some comments and rename variables.

This fixes a bug which prevented 802.11b/g non-AP STAs from working with
802.11b only AP STAs.
Signed-off-by: NStefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch removes the 802.1X port acess control enable flag
since it is not required. Instead, set the authorized flag for
each station that we normally communicate with (WDS peers, IBSS
peers and APs we're associated to) and require hostapd to set
the authorized flag for all stations when port control is not
enabled.

Also, since I was working in that area, this documents station
flags and removes the unused "permanent" one.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When checking for the next band to advance to, there
was an off-by-one error that could lead to an access
to an invalid array index. Additionally, the later
check for scan_band >= IEEE80211_NUM_BANDS is not
required since that will never be true.

This also improves the comments related to that code.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This makes nl80211 export the hardware bitrate/channel capabilities
as registered in a wiphy.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>