This is the right source of information for the valid Tx
antennas, not the NVM.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This data should taken from TLVs and not from the NVM. This
is true for the value written in CSR_HW_IF_CONFIG_REG too.

Also, no need to set the CSR_HW_IF_CONFIG_REG_BIT_MAC_SI bit
for 7000 devices which are the only devices currently
supported.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In firmware "listener" (monitor) mode, we still need to
open up the filters with the filter flags to receive all
frames.
Reviewed-by: NIlan Peer <ilan.peer@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This has valuable data about RFkill state seen from the fw
side.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

5ghz_disable has no effect any longer, that was changed during
refactoring of EEPROM reading/parsing. Remove it, wpa_supplicant
allow now to specify frequencies, on which device will operate.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

1. Quota for the monitor interface should be added only if there is
   a channel context assigned to the interface.
2. In the unassign channel context flow, need to remove the quota
   for the monitor interface binding, before unbinding.
Signed-off-by: NIlan Peer <ilan.peer@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Signed-off-by: NAndrei Epure <epure.andrei@gmail.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Signed-off-by: NIlan Peer <ilan.peer@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This feature is not implemented yet in firmware.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The masks were wrong. They should be 0xffffffff when SCO,
HID or SNIFF profiles are used. They should be 0xffff0000
in any other case (default) to get a bit more throughput
when the BT profile allows for it.

Fix a debug print on the way.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Mostly for debugging purposes
Signed-off-by: NIlan Peer <ilan.peer@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In AP mode, don't attempt to program GTKs into the
device, they're used for TX only so not needed and
programming them causes error messages. Also, in
this case and if key programming fails, avoid trying
to remove the key that isn't present later.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The code removed in this patch was used for bring up on
older NICs. No MVM capable fw will ever be released for
older NICs, so remove that code.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The SCD byte count layout is decided by the configuration
done in fw, it is then logical to export it as a TLV flag
and not per HW SKU.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Fix a bug in writing to indirect (periphery) registers; although
writes seem successful the data is not written to the desired
address). Also fix address mask for HBUS_TARG_PRPH_RADDR and
HBUS_TARG_PRPH_WADDR registers.
Signed-off-by: NAmnon Paz <amnonX.paz@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This allows to test fw restart flow. The hook in transport
layer doesn't really make the fw assert. Moving this hook
to the op_mode allows to use the fw API to actually send a
host command that will make the fw assert.

Change the restart_fw module parameter to be a boolean on
the way.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The firmware tells the driver to what MACs the received frame
belongs (based on the time slot in which it was received).

Note that there can be several MACs if they share the same
binding.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This will allow to track how BT core updates the driver.
This is required to debug the BT Coexistence mechanism.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When BT traffic load gets higher, we want to avoid using the
shared antenna. In order to do so, we need to tell the AP
that we don't support MIMO any more, or at least not all
the time: in short, use the SMPS to achieve this.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The BT-Coex notification is sent by the fw when there are
updates wrt. BT activity. Driver action might be taken
based on the info in this notification.

For now, update the Ack/Cts_kill_msk if HID / SCO / A2DP
profiles are active.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Send the PRIO table before the calibrations. This table
tells the fw what priority to give to what (WiFi / BT)
according to events.

Send a hardcoded BT_COEX command to the fw to enable basic
BT coexistence.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This is the API to tell the fw to handle the BT Coexistence.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Then the transport can print it nicely in its debug prints.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

If all the pieces of iwlwifi are built into the kernel
then there's no need for it to export its symbols to
other modules, so prevent that.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Now that we have two drivers (DVM and MVM) stop selecting
the DVM one (but make it default) and allow enabling only
the MVM driver if so desired. Add a warning for the case
of having neither DVM nor MVM enabled -- that's useless.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Signed-off-by: NDor Shaish <dor.shaish@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When modifying a MAC, we update its beacon system time which
is taken as a base to calculate TBTT. The firmware doesn't use
the new timestamp because the time is never used after the MAC
and broadcast station were added, but it is safer to not rely
on this and avoids the overhead of reading the register every
time the MAC is updated.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: NIlan Peer <ilan.peer@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Newer devices can work on different buses. This means that
their configuration can be shared between different buses.
Hence the configuration structures should exported to all
the buses and not only to PCIE. Change this.

Note that this requires all the fields to be the same
amongst the buses. If differences will appear, we can always
define a part that is bus dependent. Today, this is not
needed.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

All the data coming from the fw must have a length that is
multiple of 4.
This doesn't change anything to the way we handle the
notification.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Update the NVM parsing functions to add VHT capabilities;
they are only added for 5 GHz, of course. This assumes
that all devices with NVM reading (rather than EEPROM)
that support 5 GHz have VHT, which is true right now.
Signed-off-by: NEytan Lifshitz <eytan.lifshitz@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When a station is added, we need to tell the firmware what
the SMPS settings and number of streams are. After having
the initial data, the firmware will track future changes
by itself.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

With remote wake, the firmware creates a TCP connection
and sends some configurable data on it, until a special
TCP data packet from the server is received that triggers
a wakeup. The configuration is a bit tricky because it is
based on packet pattern matching but this is hidden in
the driver and the exposed API in cfg80211 is just based
on the required TCP connection parameters.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This removes an open coded simple_open() function and
replaces file operations references to the function
with simple_open() instead.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Instead of using (char *)__get_dynamic_array use
__get_str. The latter is actually a macro that
expands to the former in the code, but trace-cmd
in userspace can parse __get_str only.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

All hardware after 4965 supports this. It's likely that
it wasn't set because for 4965 it was irrelevant (HT is
only supported on 5 GHz there) and then never updated.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

mac80211 tells us when we need to dump the frames from the
AGG queue instead of releasing them as single MPDUs.
Being able to differentiate between the different cases
(IEEE80211_AMPDU_TX_STOP_*) allows us to handle races better.

When the station is removed, mac80211 asks to flush and
removes the station right away.
This allows to avoid a case where we still have frames in
AGG queues, but the station has been remove already.

Note that we can have frames on the shared queues, but this
is not a problem: the station in the fw will be kept until
all the frames on the shared queues have been drained.
AGG queues are a special case since they are dynamically
allocated.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Use the number of addresses (max 5) from the NVM
instead of limiting to 2 artificially.
Signed-off-by: NIlan Peer <ilan.peer@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There's a bug that causes the rate scaling to get stuck
when it has to use single-stream rates with a peer that
can do GF and SGI; the two are incompatible so we can't
use them together, but that causes the algorithm to not
work at all, it always rejects updates.

Disable greenfield for now to prevent that problem. The
MVM driver currently only works on devices that don't
support greenfield anyway, but better be safe and not
allow us to forget about this.
Signed-off-by: NBeni Lev <beni.lev@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The 7000 series devices don't support HT greenfield mode
so don't advertise or use it.
Signed-off-by: NBeni Lev <beni.lev@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>