Tested by Henrik Hjelte
zd1211b chip 13b1:0024 v4802 high 00-14-bf AL2230_RF pa0 ----
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Instead of passing our own custom 32-bit addresses around and
translating them, this patch makes all our register address constants
absolute and removes the translation.

There are two ugly parts:
 - fw_reg_addr() is needed to compute addresses of firmware registers, as this
   is dynamic based upon firmware
 - inc_addr() needs a small hack to handle byte vs word addressing

However, both of those are only small, and we don't use fw_regs a whole
lot anyway.

The bonuses here include simplicity and improved driver readability. Also, the
fact that registers are now referenced by 16-bit absolute addresses (as
opposed to 32-bit pseudo addresses) means that over 2kb compiled code size has
been shaved off.

Includes some touchups and sparse fixes from Ulrich Kunitz.
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The zd1211rw address space has confused me once too many times. This
patch introduces the following naming notation:

Memory space is split into segments (cr, fw, eeprom) and segments may
contain components (e.g. boot code inside eeprom). These names are
arbitrary and only for the description below:

x_START: Absolute address of segment start
(previously these were named such as CR_BASE_OFFSET, but they weren't
really offsets unless you were considering them as an offset to 0)

x_LEN: Segment length

x_y_LEN: Length of component y of segment x

x_y_OFFSET: Relative address of component y into segment x. The absolute
address for this component is (x_START + x_y_OFFSET)

I also renamed EEPROM registers to EEPROM data. These 'registers' can't
be written to using standard I/O and really represent predefined data
from the vendor.
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Philips SNU5600, tested by unibrow
zd1211b chip 0471:1236 v4810 high 00-12-bf AL2230_RF pa0 g--

SMC Ez Connect 802.11g (SMCWUSB-G), tested by Victorino Sanz Prat
zd1211b chip 083a:4505 v4810 full 00-13-f7 AL2230_RF pa0 g--N
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Many of the registers written during ZD1211 HMAC initialization are
duplicated exactly for ZD1211B. Move the identical ones into a generic
part, and write the hardware-specific ones separately.
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>

The driver was still mis-calculating the number of bytes sent during
transmit, now the driver computes what appears to be exactly 100%
correct byte counts (not including CRC) when figuring out how many
bytes and frames were sent during the current transmit packet.

Since the driver sets the IP checksum insertion bit (IXSM in Status
field) in transmit context descriptors, it should clear the IP checksum
bits of any garbage so as not to confuse the hardware.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>

Print RX/TX flow control setting at link up time to display the
actual link FC properties instead of the advertised values.
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>

This fix attempts to solve a customer (IBM) reported issue with NAPI
enabled e1000 having bad performance when transmitting simultaneously
on four ports.  The issue comes down to an interaction between NAPI,
hardware interrupt balancing, and the driver rescheduling poll on
the same processor.  Try to fix by allowing the driver to re-enable
interrupts sooner instead of polling one more time, when there was
recently all the work completed in cleanup.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>

Unfortunately the read-free MSI interrupt handler needs to flush write
the icr register and thus we can't be read-free. Our MSI irq routine
thus becomes a lot more simpler since we don't need to track link state
anymore.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>

Remove unused MSGOUT macro and add "\n" to function debug output.
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>

Remvoe duplicate code handling erraneous user supplied wrong case
of gigabit speed with half duplex.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>

That code doesn't do what its author apparently thought it would do...
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

smc911x_phy_configure's error handling unconditionally unlocks the
spinlock even if it wasn't locked. Patch fixes it.
Signed-off-by: NPeter Korsgaard <jacmet@sunsite.dk>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

	sd_probe() calls class_device_add() even before initializing the
sdkp->device variable. class_device_add() eventually results in the user mode
udev program to be called. udev program can read the the allow_restart
attribute of the newly created scsi device. This is resulting in a crash as
the show function for allow_restart (i.e sd_show_allow_restart) returns the
attribute value by reading the sdkp->device->allow_restart variable. As the
sdkp->device is not initialized before calling the user mode hotplug helper,
this results in a crash.
	The patch below solves it by calling class_device_add() only after the
necessary fields in the scsi_disk structure are initialized properly.
Signed-off-by: NNagendra Singh Tomar <nagendra_tomar@adaptec.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Some LLDDs, like ipr, use nbytes and pad_len to determine
the total data transfer length of a command. Make sure
nbytes gets initialized for internally generated commands.
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The 8237S was added to the chipsets but not to the comments. Fix this
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

For all JMicrons except for 361 and 368, AHCI mode enable bits in the
Control(1) should be set.  This used to be done in both ahci and
pata_jmicron but while moving programming to PCI quirk, it was removed
from ahci part while still left in pata_jmicron.

The implemented JMicron PCI quirk was incorrect in that it didn't
program AHCI mode enable bits.  If pata_jmicron is loaded first and
programs those bits, the ahci ports work; otherwise, ahci device
detection fails miserably.

This patch makes JMicron PCI quirk clear SATA IDE mode bits and set
AHCI mode bits and remove the respective part from pata_jmicron.
Tested on JMB361, 363 and 368.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

We forget to call spider_net_free_rx_chain_contents which does the
actual dev_kfree_skb. New skbs are allocated from skbuff_head_cache
on each "ifconfig up" letting the cache grow infinitely.

This patch fixes it.
Signed-off-by: NJens Osterkamp <jens@de.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

e100: fix napi ifdefs removing needed code

From: Auke Kok <auke-jan.h.kok@intel.com>

The e100 driver is NAPI mode only. We need to netif_poll_disable
during suspend and shutdown. The non-NAPI driver code was removed
and is only avaiable in the out-of-tree e100 kernel driver.
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

5709 A0 copper devices will not link up with some link partners
without this workaround.

Update driver to 1.5.5.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Noticed by JosephChan@via.com.tw.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Change SysRq showBlockedTasks from sysrq-X to sysrq-W and show that in the
Help message.

It was previously done via X, but X is already used for Xmon on ppc & powerpc
platforms and this collision needs to be avoided.

All callers of register_sysrq_key() are now marked in the sysrq op/key table.
I didn't mark 'h' as Help because Help is just printed for any unknown key,
such as '?'.

Added some omitted sysrq key entries in the sysrq.txt file.
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Intel hosts, without long mode, and with nx support disabled in the bios
have an efer that is readable but not writable.  This causes a lockup on
switch to guest mode (even though it should exit with reason 34 according
to the documentation).
Signed-off-by: NAvi Kivity <avi@qumranet.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove these recently-added warnings.  They don't tell us anythng very
interesting and Kumar says "On an embedded PPC reference system I see this
message 6 times when I've got no cards in the PCI slots."
Acked-by: NKumar Gala <galak@kernel.crashing.org>
Acked-by: NGreg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add special handling for the VT82C686.
Signed-off-by: NJean Delvare <jdelvare@suse.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Won't build (request_irq()/free_irq()), even if you manage to find an
s390 box with 8250-compatible UART they are expecting.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Acked-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

a) cleanup_module() should be __exit
b) externs should match reality
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

	Have fun.

>From 24f4a1a77431575a9cdfaae25adda85842099f70 Mon Sep 17 00:00:00 2001
From: Al Viro <viro@zeniv.linux.org.uk>
Date: Mon, 1 Jan 2007 15:22:56 -0500
Subject: [PATCH] netxen trivial annotations
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Fix a dangling pointer bug in ipmi_timeout_handler.  A list of timedout
messages is not re-initialized before reuse, causing the head of the list
to point to freed memory.
Signed-off-by: NDavid Barksdale <amatus@ocgnet.org>
Signed-off-by: NCorey Minyard <minyard@acm.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

jmicron module detects all JMB36x as JMB361 and PATA0 has wrong pin status
of XICBLID.

Cc: Jeff Garzik <jeff@garzik.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix VIA quirks that were recently broken by Alan Cox in the upstream
kernel (commit 1597cacb).

My understanding is that pci_find_present() doesn't work yet at the time
the quirks are run.  So I used a two-step quirk as is done for some other
quirks already.  First we detect the VIA south bridges and set the right
low and high device limits, then we are ready to actually run the quirks on
the affected devices.
Signed-off-by: NJean Delvare <jdelvare@suse.de>
Acked-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: NNick Piggin <nickpiggin@yahoo.com.au>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This reverts commit 0c0b3ae6.

Quoth David:

  "Jeff, please revert

   It's wrong.  We had a lengthy analysis of this piece of code
   several months ago, and it is correct.

   Consider, if we run the loop and we get an error
   the following happens:

   1) attempt of ifb_init_one(i) fails, therefore we should
      not try to "ifb_free_one()" on "i" since it failed
   2) the loop iteration first increments "i", then it
      check for error

   Therefore we must decrement "i" twice before the first
   free during the cleanup.  One to "undo" the for() loop
   increment, and one to "skip" the ifb_init_one() case which
   failed."
Reported-by: NDavid Miller <davem@davemloft.net>
Acked-by: NJeff Garzik <jgarzik@pobox.com>
Cc: Andrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

What DMA for 16bit pcmcia card, anyway?  We never do request_dma()
there and ->dma_channel never changes since initialization to -1.
IOW, that call is dead code.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix what looks like an obvious typo in the file drivers/kvm/svm.c.
Signed-off-by: NRobert P. J. Day <rpjday@mindspring.com>
Acked-by: NAvi Kivity <avi@qumranet.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>