This fixes up:
commit 464231fb
"pinctrl: ssbi-gpio: Be sure to clamp return value"
commit b9164f04
"gpio: ssbi-mpp: Be sure to clamp return value"
as I managed to screw up some of the logic when clamping
the return values.

Cc: Björn Andersson <bjorn@kryo.se>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The of_get_named_gpio_flags() function does nothing other than returning
an error when CONFIG_OF_GPIO is disabled, but that causes spurious
warnings about possible use of uninitialized variables in any code that
does not check the of_get_named_gpio_flags() return value before trying
to use the flags:

drivers/input/misc/rotary_encoder.c: In function 'rotary_encoder_probe':
drivers/input/misc/rotary_encoder.c:223:28: warning: 'flags' may be used uninitialized in this function [-Wmaybe-uninitialized]
drivers/power/bq24735-charger.c: In function 'bq24735_charger_probe':
drivers/power/bq24735-charger.c:227:12: warning: 'flags' may be used uninitialized in this function [-Wmaybe-uninitialized]
drivers/power/sbs-battery.c: In function 'sbs_probe':
drivers/power/sbs-battery.c:782:17: warning: 'gpio_flags' may be used uninitialized in this function [-Wmaybe-uninitialized]

This changes the behavior of the inline helper to set the flags to zero
when OF_GPIO is disabled, to avoid the warnings. In all cases I've
encountered, we don't actually get to the place that uses the flags
if CONFIG_OF is disabled because we won't enter the DT parser code.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

We were getting build warning about "iterator" being used uninitialized.
Use iterator properly to fix the build warning and in the process remove
the variable "pos" which is not required now.
Signed-off-by: NSudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Since gpiochip .get() callback may return a negative error value, it
strictly limits the range of possible non-error returned values to
a subset of [30:0] bitmask, however on practice on success all
gpiochip drivers return either 0 for low signal or 1 for high signal,
this is assured by "gpio: *: Be sure to clamp return value" series of
changes. To avoid any confusion, misinterpretation and potential
errors while developing gpiochip drivers in future convert this
implicit assumption to a mandatory rule.

For output signals with unknown output signal state gpiochip drivers
should return a negative error instead of 0.
Signed-off-by: NVladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This reverts commit 45ad7db9.

We have fixed all the drivers that were returning ambious values
not clamped to [0,1] or an error code, so return the error
propagating behaviour of the API.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.

Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.

This code was also double-inverting a bool which makes no sense
so I removed that code and moved clamping toward the end.

Cc: Björn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.

Also, this code was double-inverting a bool. That makes no
sense whatsoever, so I removed the double-invert.

Cc: Björn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.

Cc: Björn Andersson <bjorn.andersson@sonymobile.com>
Cc: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.

Cc: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Cc: Björn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.

Cc: Pramod Gurav <pramod.gurav@smartplayin.com>
Cc: John Crispin <blogic@openwrt.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Acked-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.

Cc: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Acked-by: NJames Hogan <james.hogan@imgtec.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Acked-by: NJames Hogan <james.hogan@imgtec.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.

This also makes the driver start to return the error code, as the
end of the series make this work.

Cc: Roger Quadros <rogerq@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.

This also starts to propagate the error code from the I2C
transaction as the end of the series adds support for that.

Cc: Wei Chen <Wei.Chen@csr.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.

Cc: Alessandro Rubini <rubini@gnudd.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.

Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.

Cc: Thierry Reding <treding@nvidia.com>
Cc: Daniel Krueger <daniel.krueger@systec-electronic.com>
Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.

Also start returning the error code if something fails, as the
end of the series augment the core to support this.

Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: George Cherian <george.cherian@ti.com>
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Acked-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.

Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.

Cc: Feng Tang <feng.tang@intel.com>
Cc: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.

Also start to propagate the error code here as the end of the
series fixes this to work for all drivers.

Cc: Semen Protsenko <semen.protsenko@globallogic.com>
Reviewed-by: NMarek Vasut <marex@denx.de>
Reviewed-by: NNicholas Krause <xerofoify@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.

Cc: Roland Stigge <stigge@antcom.de>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.

Cc: Brunner Michael <Michael.Brunner@kontron.com>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.

Cc: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Acked-by: NDavid Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.

Cc: Magnus Damm <damm@opensource.se>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.

Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.

Cc: Ashish Jangam <ashish.jangam@kpitcummins.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Signed-off-by: NPeter Rosin <peda@axentia.se>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Performing a read operation on the IRQ Status register will clear the
IRQ latch. Since a read operation on the IRQ Status register must be
performed in the IRQ handler in order to determine if the IRQ was in
fact generated by the device, the IRQ latch is consequently cleared by
the IRQ handler. A spinlock is used to guarantee that each IRQ is
serviced in the order it was received.
Signed-off-by: NWilliam Breathitt Gray <vilhelm.gray@gmail.com>

Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The commit "gpio: pxa: change the interrupt management" should have
taken care of moving an ifdef to not englobe irqdomain related
structures anymore, as they are used now for all builds.

This repairs the broken builds where CONFIG_OF=n.
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This removes the set_irq_flags() call that unfortunately slipped
into the BCM NSP driver.
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Cc: Yendapally Reddy Dhananjaya Reddy <yrdreddy@broadcom.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>