Since clock support is optional across processors, don't make the whole
musb pm paths depend upon it.  Just conditionalize the clock accesses.
Signed-off-by: NBob Liu <lliubbo@gmail.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The new MUSB power code needs musb_read_txhubport() to
return a value (so stub it as 0 like the other Blackfin
hub funcs).
Signed-off-by: NIan Jeffray <ian@jeffray.co.uk>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Commit 9f445cb2[USB: musb: disable
double buffering for older RTL versions] tries to disable double
buffer mode by writing endpoint hw max packet size to TXMAP/RXMAP.

First the approach can break full speed and cause overflow problems.
We should always set those registers with the actual max packet size
from endpoint descriptor.

Second, the problem describe by commit 9f445cb2
was caused by musb gadget driver; nothing to do with RTL revision as
originaly suspected.

The real fix to the problem is to always use actual max packet
size from endpoint descriptor to config TXMAP/RXMAP registers.

Cc: Cliff Cai <cliff.cai@analog.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: stable@kernel.org
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Some actions like musb_platform_exit are only performed on module
removal and not on shutdown, which results in PHY being left enabled
on reboot at least. This is sometimes causing strange failures after
reboot (observed on OMAP3 pandora board), when DEVCTL does not report
VBUS state correctly due to unknown reasons (possibly because of
communication issues between musb IP and PHY). Running
musb_platform_exit before reset seems to resolve that issue.

Move some exit code from musb_remove() to musb_shutdown() so that it
is performed on both module removal and shutdown/reset. Also convert
the host check so that it doesn't need #ifdef.
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

In function musb_gadget_setup() call put_device()
when device_register() fails.
Signed-off-by: NRahul Ruikar <rahul.ruikar@gmail.com>
Acked-by: NMing Lei <tom.leiming@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

1, In Rx double buffer case, FIFO may have two packets, so
rxstate should be called to unload fifo if RXPKTRDY is set
even the current request has not been completed.

2, Commit 633ba7876b96ec339ef685357e2f7c60b5a8ce85
introduces autoclear to support double buffer in dma mode 0,
so remove clearing RXPKTRDY manually for dma mode 0.

3, Commit c7af6b29ffeffbeb28caf39e5b2ce29b11807c7d may break
dma mode 1 for non-doublebuffer endpoint, fix it.

With this patch, either usbtest #5 or g_file_storage(writing
file to device in usb host) or g_ether have been tested OK in
double buffer case(using fifo mode 3). Also, this patch has
been verified that single buffer case can't be broken.

Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

* 'for-linus' of git://www.jni.nu/cris:
  CRIS: Add paths for CRISv10 serial driver
  CRIS: Fix RS485 delay handling.
  Add missing "struct" to in sizeof.

* 'next-spi' of git://git.secretlab.ca/git/linux-2.6:
  spi/pl022: fix erroneous platform data in U300
  spi: fixed odd static string conventions in core code
  spi/bfin_spi: only request GPIO on first load
  spi/bfin_spi: handle error/status changes after data interrupts
  spi: enable spi_board_info to be registered after spi_master

Signed-off-by: NJesper Nilsson <jesper.nilsson@axis.com>

This fixes an erroneous use of LSB first in the U300 machine, the
PL022 used in U300 is a standard ARM core that doesn't support this
bit so it should never have been set.

Cc: Kevin Wells <wellsk40@gmail.com>OA
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

We were forgetting to set up proper return value in success path causing
ir_getkeycode() to fail intermittently:

drivers/media/IR/ir-keytable.c: In function 'ir_getkeycode':
drivers/media/IR/ir-keytable.c:363: warning: 'retval' may be used
uninitialized in this function
Reported-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  i2c-i801: Add PCI idents for Patsburg 'IDF' SMBus controllers
  i2c-i801: Handle multiple instances instead of keeping global state
  i2c-i801: Add Intel Patsburg device ID
  i2c: Drop unused I2C_CLASS_TV flags

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: appletouch - remove extra KERN_DEBUG use from dprintk
  Input: bu21013_ts - fix null dereference in error handling
  Input: ad7879 - prevent invalid finger data reports

* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (70 commits)
  [SCSI] pmcraid: add support for set timestamp command and other fixes
  [SCSI] pmcraid: remove duplicate struct member
  [SCSI] qla4xxx: Fix cmd check in qla4xxx_cmd_wait
  [SCSI] megaraid_sas: Version and documentation update
  [SCSI] megaraid_sas: Add three times Online controller reset
  [SCSI] megaraid_sas: Add input parameter for max_sectors
  [SCSI] megaraid_sas: support devices update flag
  [SCSI] libosd: write/read_sg_kern API
  [SCSI] libosd: Support for scatter gather write/read commands
  [SCSI] libosd: Free resources in reverse order of allocation
  [SCSI] libosd: Fix bug in attr_page handling
  [SCSI] lpfc 8.3.18: Update lpfc driver version to 8.3.18
  [SCSI] lpfc 8.3.18: Add new WQE support
  [SCSI] lpfc 8.3.18: Fix critical errors
  [SCSI] lpfc 8.3.18: Adapter Shutdown and Unregistration cleanup
  [SCSI] lpfc 8.3.18: Add logic to detect last devloss timeout
  [SCSI] lpfc 8.3.18: Add support of received ELS commands
  [SCSI] lpfc 8.3.18: FC/FCoE Discovery fixes
  [SCSI] ipr: add definitions for a new adapter
  [SCSI] bfa: fix comments for c files
  ...

Merge branches 'irq-core-for-linus' and 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  genirq: Fix up irq_node() for irq_data changes.
  genirq: Add single IRQ reservation helper
  genirq: Warn if enable_irq is called before irq is set up

* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  semaphore: Remove mutex emulation
  staging: Final semaphore cleanup
  jbd2: Convert jbd2_slab_create_sem to mutex
  hpfs: Convert sbi->hpfs_creation_de to mutex

Fix up trivial change/delete conflicts with deleted 'dream' drivers
(drivers/staging/dream/camera/{mt9d112.c,mt9p012_fox.c,mt9t013.c,s5k3e2fx.c})

These are the extra 'Integrated Device Function' SMBus controllers found
on the Patsburg chipset. Mention the absence of slave mode support.
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

It's poor form to keep driver state in global variables rather than
per-instance. It never really mattered in practice when there was only
one controller on the chipset, but the latest chipsets do have more
than one controller, so now we care.
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Add support for the Intel Patsburg PCH SMBus Controller.
Signed-off-by: NSeth Heasley <seth.heasley@intel.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

There are no users left for I2C_CLASS_TV_ANALOG and
I2C_CLASS_TV_DIGITAL, so we can get rid of them.
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

This one was only used for a nasty hack in nfsd, which has recently
been removed.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The caller allocated it, the caller should free it.

The only issue so far is that we could change the flp pointer even on an
error return if the fl_change callback failed.  But we can simply move
the flp assignment after the fl_change invocation, as the callers don't
care about the flp return value if the setlease call failed.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit ffe8018c ("initramfs: fix initramfs size calculation") broke
32-bit big-endian arches like (on ARAnyM):

    VFS: Cannot open root device "hda1" or unknown-block(3,1)
    Please append a correct "root=" boot option; here are the available partitions:
    fe80         1059408 nfhd8  (driver?)
      fe81          921600 nfhd8p1 00000000-0000-0000-0000-000000000nfhd8p1
      fe82          137807 nfhd8p2 00000000-0000-0000-0000-000000000nfhd8p2
    0200            3280 fd0  (driver?)
    0201            3280 fd1  (driver?)
    0300         1059408 hda  driver: ide-gd
      0301          921600 hda1 00000000-0000-0000-0000-000000000hda1
      0302          137807 hda2 00000000-0000-0000-0000-000000000hda2
    Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(3,1)

As pointed out by Kerstin Jonsson <kerstin.jonsson@ericsson.com>, this
is due to CONFIG_32BIT not being defined, so the initramfs size field is
done as a 64-bit quad.  On little-endian (like x86) this doesn matter,
but on a big-endian machine the 32-bit reads will see the (zero) high
bits.

Only mips, s390, and score set CONFIG_32BIT for 32-bit builds, so fix it for
all other 32-bit arches by inverting the logic and testing for CONFIG_64BIT,
which should be defined on all 64-bit arches.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
[ I think we should just make it "u64" on all architectures and get
  rid of the whole #ifdef CONFIG_xxBIT   - Linus ]
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  isdn: mISDN: socket: fix information leak to userland
  netdev: can: Change mail address of Hans J. Koch
  pcnet_cs: add new_id
  net: Truncate recvfrom and sendto length to INT_MAX.
  RDS: Let rds_message_alloc_sgs() return NULL
  RDS: Copy rds_iovecs into kernel memory instead of rereading from userspace
  RDS: Clean up error handling in rds_cmsg_rdma_args
  RDS: Return -EINVAL if rds_rdma_pages returns an error
  net: fix rds_iovec page count overflow
  can: pch_can: fix section mismatch warning by using a whitelisted name
  can: pch_can: fix sparse warning
  netxen_nic: Fix the tx queue manipulation bug in netxen_nic_probe
  ip_gre: fix fallback tunnel setup
  vmxnet: trivial annotation of protocol constant
  vmxnet3: remove unnecessary byteswapping in BAR writing macros
  ipv6/udp: report SndbufErrors and RcvbufErrors
  phy/marvell: rename 88ec048 to 88e1318s and fix mscr1 addr

The NFSv4 server was initializing the dp->dl_flock pointer by the
somewhat ridiculous method of a locks_copy_lock callback.

Now that setlease uses the passed-in lock instead of doing a copy,
dl_flock no longer gets set, resulting in the lock leaking on delegation
release, and later possible hangs (among other problems).

So, initialize dl_flock and get rid of the callback.
Signed-off-by: NJ. Bruce Fields <bfields@redhat.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We modified setlease to require the caller to allocate the new lease in
the case of creating a new lease, but forgot to fix up the filesystem
methods.

Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Steve French <sfrench@samba.org>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: NJ. Bruce Fields <bfields@redhat.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We're depending on setlease to free the passed-in lease on failure.
Signed-off-by: NJ. Bruce Fields <bfields@redhat.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Removing a lock shouldn't require any allocations; a failure due to
ENOMEM leaves the caller with a choice between retrying or giving up and
leaking an unused lease.

Next we should split the other lease calls into add and delete cases.
I wanted to start with just the bugfix.
Signed-off-by: NJ. Bruce Fields <bfields@redhat.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The input-large-scancode patches changed the binary search in
drivers/media/IR/ir-keytable.c to use unsigned integers, but
signed integers are actually necessary for the algorithm to work.
Signed-off-by: NDavid Härdeman <david@hardeman.nu>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Structure mISDN_devinfo is copied to userland with the field "name"
that has the last elements unitialized.  It leads to leaking of
contents of kernel stack memory.
Signed-off-by: NVasiliy Kulikov <segooon@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

My old mail address doesn't exist anymore. This changes all occurrences
to my new address.
Signed-off-by: NHans J. Koch <hjk@hansjkoch.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

pcnet_cs:
    add new_id: "corega Ether CF-TD" 10Base-T PCMCIA card.
Signed-off-by: NKen Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Even with the previous fix, we still are reading the iovecs once
to determine SGs needed, and then again later on. Preallocating
space for sg lists as part of rds_message seemed like a good idea
but it might be better to not do this. While working to redo that
code, this patch attempts to protect against userspace rewriting
the rds_iovec array between the first and second accesses.

The consequences of this would be either a too-small or too-large
sg list array. Too large is not an issue. This patch changes all
callers of message_alloc_sgs to handle running out of preallocated
sgs, and fail gracefully.
Signed-off-by: NAndy Grover <andy.grover@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change rds_rdma_pages to take a passed-in rds_iovec array instead
of doing copy_from_user itself.

Change rds_cmsg_rdma_args to copy rds_iovec array once only. This
eliminates the possibility of userspace changing it after our
sanity checks.

Implement stack-based storage for small numbers of iovecs, based
on net/socket.c, to save an alloc in the extremely common case.

Although this patch reduces iovec copies in cmsg_rdma_args to 1,
we still do another one in rds_rdma_extra_size. Getting rid of
that one will be trickier, so it'll be a separate patch.
Signed-off-by: NAndy Grover <andy.grover@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We don't need to set ret = 0 at the end -- it's initialized to 0.

Also, don't increment s_send_rdma stat if we're exiting with an
error.
Signed-off-by: NAndy Grover <andy.grover@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

rds_cmsg_rdma_args would still return success even if rds_rdma_pages
returned an error (or overflowed).
Signed-off-by: NAndy Grover <andy.grover@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As reported by Thomas Pollet, the rdma page counting can overflow.  We
get the rdma sizes in 64-bit unsigned entities, but then limit it to
UINT_MAX bytes and shift them down to pages (so with a possible "+1" for
an unaligned address).

So each individual page count fits comfortably in an 'unsigned int' (not
even close to overflowing into signed), but as they are added up, they
might end up resulting in a signed return value. Which would be wrong.

Catch the case of tot_pages turning negative, and return the appropriate
error code.
Reported-by: NThomas Pollet <thomas.pollet@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NAndy Grover <andy.grover@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the following section mismatch warning:

WARNING: drivers/net/can/pch_can.o(.data+0x18):
Section mismatch in reference from the variable pch_can_pcidev
to the variable .devinit.rodata:pch_pci_tbl
The variable pch_can_pcidev references
the variable __devinitconst pch_pci_tbl

This is actually a false positive which is fixed by giving the offending
variable a whitelisted name, it's renamed to "pch_can_pci_driver".
This makes sense because the variable is of the type "struct pci_driver".
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Acked-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>