Skip to content

cloud-kernel
cloud-kernel

openanolis / cloud-kernel
1 年多 前同步成功

通知 161
Star 36
Fork 7
cloud-kernel
cloud-kernel
切换分支/标签
  1. 17 10月, 2015 2 次提交
  3. 04 10月, 2015 4 次提交
  5. 09 8月, 2015 2 次提交
  7. 23 7月, 2015 1 次提交
  9. 31 5月, 2015 1 次提交
  11. 25 5月, 2015 1 次提交
    • C
      usb: host: xhci: add mutex for non-thread-safe data · a00918d0
      由 Chris Bainbridge 提交于 
      Regression in commit 638139eb ("usb: hub: allow to process more usb
hub events in parallel")

The regression resulted in intermittent failure to initialise a 10-port
hub (with three internal VL812 4-port hub controllers) on boot, with a
failure rate of around 8%, due to multiple race conditions when
accessing addr_dev and slot_id in struct xhci_hcd.

This regression also exposed a problem with xhci_setup_device, which
"should be protected by the usb_address0_mutex" but no longer is due to

commit 6fecd4f2 ("USB: separate usb_address0 mutexes for each bus")

With separate buses (and locks) it is no longer the case that a single
lock will protect xhci_setup_device from accesses by two parallel
threads processing events on the two buses.

Fix this by adding a mutex to protect addr_dev and slot_id in struct
xhci_hcd, and by making the assignment of slot_id atomic.

Fixes multiple boot errors:

[ 0.583008] xhci_hcd 0000:00:14.0: Bad Slot ID 2
[ 0.583009] xhci_hcd 0000:00:14.0: Could not allocate xHCI USB device data structures
[ 0.583012] usb usb1-port3: couldn't allocate usb_device

And:

[ 0.637409] xhci_hcd 0000:00:14.0: Error while assigning device slot ID
[ 0.637417] xhci_hcd 0000:00:14.0: Max number of devices this xHCI host supports is 32.
[ 0.637421] usb usb1-port1: couldn't allocate usb_device

And:

[ 0.753372] xhci_hcd 0000:00:14.0: ERROR: unexpected setup context command completion code 0x0.
[ 0.753373] usb 1-3: hub failed to enable device, error -22
[ 0.753400] xhci_hcd 0000:00:14.0: Error while assigning device slot ID
[ 0.753402] xhci_hcd 0000:00:14.0: Max number of devices this xHCI host supports is 32.
[ 0.753403] usb usb1-port3: couldn't allocate usb_device

And:

[ 11.018386] usb 1-3: device descriptor read/all, error -110

And:

[ 5.753838] xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command

Tested with 200 reboots, resulting in no USB hub init related errors.

Fixes: 638139eb ("usb: hub: allow to process more usb hub events in parallel")
Link: https://lkml.kernel.org/g/CAP-bSRb=A0iEYobdGCLpwynS7pkxpt_9ZnwyZTPVAoy0Y=Zo3Q@mail.gmail.comSigned-off-by: NChris Bainbridge <chris.bainbridge@gmail.com>
Cc: <stable@vger.kernel.org> # 3.18+
[changed git commit description style for checkpatch -Mathias]
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      a00918d0
  13. 10 5月, 2015 1 次提交
    • M
      xhci: Solve full event ring by increasing TRBS_PER_SEGMENT to 256 · 18cc2f4c
      由 Mathias Nyman 提交于 
      Our event ring consists of only one segment, and we risk filling
the event ring in case we get isoc transfers with short intervals
such as webcams that fill a TD every microframe (125us)

With 64 TRB segment size one usb camera could fill the event ring in 8ms.
A setup with several cameras and other devices can fill up the
event ring as it is shared between all devices.
This has occurred when uvcvideo queues 5 * 32TD URBs which then
get cancelled when the video mode changes. The cancelled URBs are returned
in the xhci interrupt context and blocks the interrupt handler from
handling the new events.

A full event ring will block xhci from scheduling traffic and affect all
devices conneted to the xhci, will see errors such as Missed Service
Intervals for isoc devices, and  and Split transaction errors for LS/FS
interrupt devices.

Increasing the TRB_PER_SEGMENT will also increase the default endpoint ring
size, which is welcome as for most isoc transfer we had to dynamically
expand the endpoint ring anyway to be able to queue the 5 * 32TDs uvcvideo
queues.

The default size used to be 64 TRBs per segment

Cc: <stable@vger.kernel.org>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      18cc2f4c
  15. 11 3月, 2015 1 次提交
  17. 07 3月, 2015 2 次提交
    • M
      xhci: Workaround for PME stuck issues in Intel xhci · b8cb91e0
      由 Mathias Nyman 提交于 
      The xhci in Intel Sunrisepoint and Cherryview platforms need a driver
workaround for a Stuck PME that might either block PME events in suspend,
or create spurious PME events preventing runtime suspend.

Workaround is to clear a internal PME flag, BIT(28) in a vendor specific
PMCTRL register at offset 0x80a4, in both suspend resume callbacks

Without this, xhci connected usb devices might never be able to wake up the
system from suspend, or prevent device from going to suspend (xhci d3)

Cc: <stable@vger.kernel.org>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      b8cb91e0
    • A
      xhci: fix reporting of 0-sized URBs in control endpoint · 45ba2154
      由 Aleksander Morgado 提交于 
      When a control transfer has a short data stage, the xHCI controller generates
two transfer events: a COMP_SHORT_TX event that specifies the untransferred
amount, and a COMP_SUCCESS event. But when the data stage is not short, only the
COMP_SUCCESS event occurs. Therefore, xhci-hcd must set urb->actual_length to
urb->transfer_buffer_length while processing the COMP_SUCCESS event, unless
urb->actual_length was set already by a previous COMP_SHORT_TX event.

The driver checks this by seeing whether urb->actual_length == 0, but this alone
is the wrong test, as it is entirely possible for a short transfer to have an
urb->actual_length = 0.

This patch changes the xhci driver to rely on a new td->urb_length_set flag,
which is set to true when a COMP_SHORT_TX event is received and the URB length
updated at that stage.

This fixes a bug which affected the HSO plugin, which relies on URBs with
urb->actual_length == 0 to halt re-submitting the RX URB in the control
endpoint.

Cc: <stable@vger.kernel.org>
Signed-off-by: NAleksander Morgado <aleksander@aleksander.es>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      45ba2154
  19. 25 2月, 2015 2 次提交
  21. 25 1月, 2015 1 次提交
  23. 10 1月, 2015 2 次提交
  25. 03 12月, 2014 2 次提交
  27. 22 11月, 2014 1 次提交
  29. 04 10月, 2014 3 次提交
  31. 24 9月, 2014 2 次提交
  33. 02 8月, 2014 1 次提交
    • H
      xhci: Blacklist using streams on the Etron EJ168 controller · 8f873c1f
      由 Hans de Goede 提交于 
      Streams on the EJ168 do not work as they should. I've spend 2 days trying
to get them to work, but without success.

The first problem is that when ever you ring the stream-ring doorbell, the
controller starts executing trbs at the beginning of the first ring segment,
event if it ended somewhere else previously. This can be worked around by
allowing enqueing only one td (not a problem with how streams are typically
used) and then resetting our copies of the enqueueing en dequeueing pointers
on a td completion to match what the controller seems to be doing.

This way things seem to start working with uas and instead of being able
to complete only the very first scsi command, the scsi core can probe the disk.

But then things break later on when td-s get enqueued with more then one
trb. The controller does seem to increase its dequeue pointer while executing
a stream-ring (data transfer events I inserted for debugging do trigger).
However execution seems to stop at the final normal trb of a multi trb td,
even if there is a data transfer event inserted after the final trb.

The first problem alone is a serious deviation from the spec, and esp.
dealing with cancellation would have been very tricky if not outright
impossible, but the second problem simply is a deal breaker altogether,
so this patch simply disables streams.

Note this will cause the usb-storage + uas driver pair to automatically switch
to using usb-storage instead of uas on these devices, essentially reverting
to the 3.14 and earlier behavior when uas was marked CONFIG_BROKEN.

https://bugzilla.redhat.com/show_bug.cgi?id=1121288
https://bugzilla.kernel.org/show_bug.cgi?id=80101

Cc: stable@vger.kernel.org # 3.15
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      8f873c1f
  35. 28 5月, 2014 1 次提交
  37. 20 5月, 2014 5 次提交
    • M
      xhci: rework command timeout and cancellation, · c311e391
      由 Mathias Nyman 提交于 
      Use one timer to control command timeout.

start/kick the timer every time a command is completed and a
new command is waiting, or a new command is added to a empty list.

If the timer runs out, then tag the current command as "aborted", and
start the xhci command abortion process.

Previously each function that submitted a command had its own timer.
If that command timed out, a new command structure for the
command was created and it was put on a cancel_cmd_list list,
then a pci write to abort the command ring was issued.

when the ring was aborted, it checked if the current command
was the one to be canceled, later when the ring was stopped the
driver got ownership of the TRBs in the command ring,
compared then to the TRBs in the cancel_cmd_list,
and turned them into No-ops.

Now, instead, at timeout we tag the status of the command in the
command queue to be aborted, and start the ring abortion.
Ring abortion stops the command ring and gives control of the
commands to us.
All the aborted commands are now turned into No-ops.

If the ring is already stopped when the command times outs its not possible
to start the ring abortion, in this case the command is turnd to No-op
right away.

All these changes allows us to remove the entire cancel_cmd_list code.

The functions waiting for a command to finish no longer have their own timeouts.
They will wait either until the command completes normally,
or until the whole command abortion is done.
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      c311e391
    • M
      xhci: Use completion and status in global command queue · 9ea1833e
      由 Mathias Nyman 提交于 
      Remove the per-device command list and handle_cmd_in_cmd_wait_list()
and use the completion and status variables found in the
command structure in the global command list.
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      9ea1833e
    • M
      xhci: Add a global command queue · c9aa1a2d
      由 Mathias Nyman 提交于 
      Create a list to store command structures, add a structure to it every time
a command is submitted, and remove it from the list once we get a
command completion event matching the command.

Callers that wait for completion will free their command structures themselves.
The other command structures are freed in the command completion event handler.

Also add a check that prevents queuing commands if host is dying
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      c9aa1a2d
    • M
      xhci: Use command structures when queuing commands on the command ring · ddba5cd0
      由 Mathias Nyman 提交于 
      To create a global command queue we require that each command put on the
command ring is submitted with a command structure.

Functions that queue commands and wait for completion need to allocate a command
before submitting it, and free it once completed. The following command queuing
functions need to be modified.

xhci_configure_endpoint()
xhci_address_device()
xhci_queue_slot_control()
xhci_queue_stop_endpoint()
xhci_queue_new_dequeue_state()
xhci_queue_reset_ep()
xhci_configure_endpoint()

xhci_configure_endpoint() could already be called with a command structure,
and only xhci_check_maxpacket and xhci_check_bandwidth did not do so. These
are changed and a command structure is now required. This change also simplifies
the configure endpoint command completion handling and the "goto bandwidth_change"
handling code can be removed.

In some cases the command queuing function is called in interrupt context.
These commands needs to be allocated atomically, and they can't wait for
completion. These commands will in this patch be freed directly after queuing,
but freeing will be moved to the command completion event handler in a later
patch once we get the global command queue up.(Just so that we won't leak
memory in the middle of the patch set)
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      ddba5cd0
    • F
      usb: xhci: Use IS_ENABLED() macro · 961b3d0a
      由 Fabio Estevam 提交于 
      Using the IS_ENABLED() macro can make the code shorter and easier to read.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      961b3d0a
  39. 26 4月, 2014 1 次提交
    • J
      usb: xhci: Prefer endpoint context dequeue pointer over stopped_trb · 1f81b6d2
      由 Julius Werner 提交于 
      We have observed a rare cycle state desync bug after Set TR Dequeue
Pointer commands on Intel LynxPoint xHCs (resulting in an endpoint that
doesn't fetch new TRBs and thus an unresponsive USB device). It always
triggers when a previous Set TR Dequeue Pointer command has set the
pointer to the final Link TRB of a segment, and then another URB gets
enqueued and cancelled again before it can be completed. Further
investigation showed that the xHC had returned the Link TRB in the TRB
Pointer field of the Transfer Event (CC == Stopped -- Length Invalid),
but when xhci_find_new_dequeue_state() later accesses the Endpoint
Context's TR Dequeue Pointer field it is set to the first TRB of the
next segment.

The driver expects those two values to be the same in this situation,
and uses the cycle state of the latter together with the address of the
former. This should be fine according to the XHCI specification, since
the endpoint ring should be stopped when returning the Transfer Event
and thus should not advance over the Link TRB before it gets restarted.
However, real-world XHCI implementations apparently don't really care
that much about these details, so the driver should follow a more
defensive approach to try to work around HC spec violations.

This patch removes the stopped_trb variable that had been used to store
the TRB Pointer from the last Transfer Event of a stopped TRB. Instead,
xhci_find_new_dequeue_state() now relies only on the Endpoint Context,
requiring a small amount of additional processing to find the virtual
address corresponding to the TR Dequeue Pointer. Some other parts of the
function were slightly rearranged to better fit into this model.

This patch should be backported to kernels as old as 2.6.31 that contain
the commit ae636747 "USB: xhci: URB
cancellation support."
Signed-off-by: NJulius Werner <jwerner@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      1f81b6d2
  41. 05 3月, 2014 3 次提交
    • H
      xhci: For streams the dequeue ptr must be read from the stream ctx · 9aad95e2
      由 Hans de Goede 提交于 
      This fixes TR dequeue validation failing on Intel XHCI controllers with the
following warning:

Mismatch between completed Set TR Deq Ptr command & xHCI internal state.

Interestingly enough reading the deq ptr from the ep ctx after a
TR Deq Ptr command does work on a Nec XHCI controller, it seems the Nec
writes the ptr to both the ep and stream contexts when streams are used.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
      9aad95e2
    • H
      xhci: Set SCT field for Set TR dequeue on streams · 95241dbd
      由 Hans de Goede 提交于 
      Nec XHCI controllers don't seem to care, but without this Intel XHCI
controllers reject Set TR dequeue commands with a COMP_TRB_ERR, leading
to the following warning:

WARN Set TR Deq Ptr cmd invalid because of stream ID configuration

And very shortly after this the system completely freezes.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
      95241dbd
    • G
      xhci: fix usb3 streams · 15341303
      由 Gerd Hoffmann 提交于 
      xhci maintains a radix tree for each stream endpoint because it must
be able to map a trb address to the stream ring.  Each ring segment
must be added to the ring for this to work.  Currently xhci sticks
only the first segment of each stream ring into the radix tree.

Result is that things work initially, but as soon as the first segment
is full xhci can't map the trb address from the completion event to the
stream ring any more -> BOOM.  You'll find this message in the logs:

  ERROR Transfer event for disabled endpoint or incorrect stream ring

This patch adds a helper function to update the radix tree, and a
function to remove ring segments from the tree.  Both functions loop
over the segment list and handles all segments instead of just the
first.

[Note: Sarah changed this patch to add radix_tree_maybe_preload() and
radix_tree_preload_end() calls around the radix tree insert, since we
can now insert entries in interrupt context.  There are now two helper
functions to make the code cleaner, and those functions are moved to
make them static.]
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
      15341303
  43. 08 2月, 2014 1 次提交