Parts that poke port specific HW blocks like the encoder HW state
readout or connector hotplug detect code need a way to check whether
required power domains are on or enable/disable these. For this purpose
add a set of power domains that refer to the port HW blocks. Get the
proper port power domains during modeset.

For now when requesting the power domain for a DDI port get it for a 4
lane configuration. This can be optimized later to request only the 2
lane power domain, when proper support is added on the VLV PHY side for
this. Atm, the PHY setup code assumes a 4 lane config in all cases.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

These functions will be needed by the valleyview specific power well
update functionality added in an upcoming patch, so move them earlier.

No functional change.

v2:
- no change
v3:
- rebase on latest -nightly
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v2)
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This macro is similar to for_each_pipe() we already have. Convert the
two call sites we have at the same time.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

I recently fumbled a patch because I wrote twice num_sprites[i], and it
was the right thing to do in only 50% of the cases.

This patch ensures I need to write num_sprites[pipe], ie it should be
self-documented that it's per-pipe number of sprites without having to
look at what is 'i' this time around.

It's all a lame excuse, but it does make it harder to redo the same
mistake.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

If we need precisely N lanes to satisfy the FDI bandwidth requirement,
the code would still claim that we need N+1 lanes. Use DIV_ROUND_UP()
to get a more accurate answer.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

After a hang and failed reset, we cannot use the GPU to execute the page
flip instructions. Instead we can force a synchronous mmio flip. (Later,
we can reduce the synchronicity of the mmio flip by moving some of the
delays off to a worker, like the current page flip code; see vblank
tasks.)

References: https://bugs.freedesktop.org/show_bug.cgi?id=72631Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Since the addition of dev_priv->mm.busy, there's no more need for
dev_priv->pc8.gpu_idle, so kill it.

Notice that when you remove gpu_idle, hsw_package_c8_gpu_idle and
hsw_package_c8_gpu_busy become identical to hsw_enable_package_c8 and
hsw_disable_package_c8, so just use them.

Also, when we boot the machine, dev_priv->mm.busy initially considers
the machine as idle. This is opposed to dev_priv->pc8.gpu_idle, which
considered it busy. So dev_priv->pc8.disable_count has to be
initalized to 1 now.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Because intel_mark_idle still touches some registers: it needs the
machine to be awake. If you set both the autosuspend and PC8 delays to
zero, you can get a "Device suspended" WARN when gen6_rps_idle touches
registers.

This is not easy to reproduce, but happens once in a while when
running pm_pc8.

Testcase: igt/pm_pc8
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We currently call intel_mark_idle() too often, as we do so as a
side-effect of processing the request queue. However, we the calls to
intel_mark_idle() are expected to be paired with a call to
intel_mark_busy() (or else we try to idle the hardware by accessing
registers that are already disabled). Make the idle/busy tracking
explicit to prevent the multiple calls.

v2: We can drop some of the complexity in __i915_add_request() as
queue_delayed_work() already behaves as we want (not requeuing the item
if it is already in the queue) and mark_busy/mark_idle imply that the
idle task is inactive.

v3: We do still need to cancel the pending idle task so that it is sent
again after the current busy load completes (not in the middle of it).
Reported-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This way we can reuse the check on other platforms too. Also factor out
a version of the function that doesn't check if the power is on, we'll
need to call this from within the power domain framework.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The power domains framework is internal to the i915 driver, so pass
drm_i915_private instead of drm_device to its functions.

Also remove a dangling intel_set_power_well() declaration.

No functional change.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This should be impossible due to the wait for outstanding flips that the
caller is meant to perform prior to updating the scanout base. Paranoia
tells me to check anyway.

References: https://bugs.freedesktop.org/show_bug.cgi?id=75502Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

To silence locking complaints.  This was a rebase failure on my part in

commit fa9fa083
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date:   Tue Feb 11 15:28:56 2014 -0800

    drm/i915: read out hw state earlier v2
Reported-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

To modeset_update_crtc_power_domains, since this function is
responsible for updating all the power domains of all CRTCs after a
modeset. In the future we should also run this function on all
platforms, not just Haswell.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Apparently we've missed a few more than what Fengguang's 0-day tester
recently reported in i915_irq.c ... Makes sparse happy again (ignore
some spurious stuff about ksyms of exported functions).

Cc: kbuild test robot <fengguang.wu@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Spotted while auditing the code for fencing issues.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Looks like I've missed one of the potential NULL deref bugs in Jesse's
fbdev->fb embedded struct to pointer conversions. Fix it up.

This regression has been introduced in

commit 8bcd4553
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date:   Fri Feb 7 12:10:38 2014 -0800

    drm/i915: alloc intel_fb in the intel_fbdev struct

Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Since

commit d9255d57
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date:   Thu Sep 26 20:05:59 2013 -0300

it became clear that we need to separate the unload sequence into two
parts:

1. remove all interfaces through which new operations on some object
   (crtc, encoder, connector) can be started and make sure all pending
   operations are completed
2. do the actual tear down of the internal representation of the above
   objects

The above commit achieved this separation for connectors by splitting
out the sysfs removal part from the connector's destroy callback and
doing this removal before calling drm_mode_config_cleanup() which does
the actual tear-down of all the drm objects.

Since we'll have to customize the interface removal part for different
types of connectors in the upcoming patches, add a new unregister
callback and move the interface removal part to it.

No functional change.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NAntti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We assign the sarea_priv pointer only in the dma ioctl, which is
disallowed when kernel modesetting is enabled. So this is dead code.

Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The BIOS or boot loader will generally create an initial display
configuration for us that includes some set of active pipes and
displays.  This routine tries to figure out which pipes and connectors
are active and stuffs them into the crtcs and modes array given to us by
the drm_fb_helper code.

The overall sequence is:
  intel_fbdev_init - from driver load
    intel_fbdev_init_bios - initialize the intel_fbdev using BIOS data
    drm_fb_helper_init - build fb helper structs
    drm_fb_helper_single_add_all_connectors - more fb helper structs
  intel_fbdev_initial_config - apply the config
    drm_fb_helper_initial_config - call ->probe then register_framebuffer()
        drm_setup_crtcs - build crtc config for fbdev
          intel_fb_initial_config - find active connectors etc
        drm_fb_helper_single_fb_probe - set up fbdev
          intelfb_create - re-use or alloc fb, build out fbdev structs

v2: use BIOS connector config unconditionally if possible (Daniel)
    check for crtc cloning and reject (Daniel)
    fix up comments (Daniel)
v3: use command line args and preferred modes first (Ville)
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Re-add the WARN_ON for a missing encoder crtc - the state
sanitizer should take care of this. And spell-ocd the comments.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We want to reuse this in the fbdev initial config code independently
from any fastboot hacks. So allow a bit more flexibility.

v2: Forgot to git add ...
v3: make non-static (Jesse)
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We want to do this early on before we try to fetch the plane config,
which depends on some of the pipe config state.

Note that the important part is that we do this before we initialize
gem, since otherwise we can't properly pre-reserve the stolen memory
for framebuffers inherited from the bios.

v2: split back out from get_plane_config change (Daniel)
    update for recent locking & reset changes (Jesse)
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Explain a bit more why we need to move this.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

... and QUIRK_PIPEA_FORCE is not present.

I initially thought that case was impossible and just added a WARN on
it, but then I was told this case is possible due to
QUIRK_PIPEA_FORCE. So let's add a WARN that serves two purposes:
  - tell us in case we have done something wrong;
  - document the only case where we expect this.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Add a nice comment explaining why we shouldn't wait for a vblank on
all cases, wait based on the HW gen, and add a comment saying we
should probably skip that wait on some of the previous HW gens.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Now that we pass struct intel_crtc as an argument, we can check for
DSI inside the function, removing one more of those confusing boolean
arguments.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Now that we pass struct intel_crtc as an argument, there's no need for
it.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We want to remove those 3 boolean arguments. This is the first step.
The "pipe" passed as the argument is always intel_crtc->pipe.

Also adjust the function documentation.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

When I forked haswell_crtc_enable I copied all the code from
ironlake_crtc_enable. The last piece of the function contains a big
comment with a call to intel_wait_for_vblank. After this fork, we
rearranged the Haswell code so that it enables the planes as the very
last step of the modeset sequence, so we're sure that we call
intel_enable_primary_plane after the pipe is really running, so the
vblank waiting functions work as expected. I really believe this is
what fixes the problem described by the big comment, so let's give it
a try and get rid of that intel_wait_for_vblank, saving around 16ms
per modeset (and init/resume). We can always revert if needed :)
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Because on Haswell, the pipe is never running at this point, so we hit
the 50ms timeout waiting for nothing. We already have two other places
where we wait for vblanks on haswell_crtc_enable, so we're safe.

This gets us rid of one instance of "vblank wait timed out" for each
mode set, which means driver init and resume are also 50ms faster.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Depending on the HW gen and the connector type, the pipe won't start
running right after we call intel_enable_pipe, so that
intel_wait_for_vblank call we currently have will just sit there for
the full 50ms timeout. So this patch adds an argument that will allow
us to avoid the vblank wait in case we want. Currently all the callers
still request for the vblank wait, so the behavior should still be the
same.

We also added a POSTING_READ on the register: previously
intel_wait_for_vblank was acting as a POSTING_READ, but now if
wait_for_vblank is false we'll stkip it, so we need an explicit
POSTING_READ.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

For use by get_plane_config.

v2: cleanup tile_height bits (Chris)
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In Jesse's patch to switch the fbdev framebuffer from an embedded
struct to a pointer the kfree in case of an error was missed. Fix this
up by using our own internal fb allocation helper directly instead of
reinventing that wheel.

We need a to_intel_framebuffer cast unfortunately since all the other
callers of _create still look better whith using a drm_framebuffer as
return pointer.

v2: Add an unlocked __intel_framebuffer_create function since our
dev->struct_mutex locking is too much a mess. With ppgtt we even need
it to take a look at the global gtt offset of pinned objects, since
the vma list might chance from underneath us. At least with the
current global gtt lookup functions. Reported by Mika.

Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Now that it's a normally kmalloce buffer we can use the usual cleanup
paths. The upside here is that if we get the refcounting wrong will be
able to catch it, since the drm core will complain about leftover
framebuffers and kref about underflows.

v2: Kill intel_framebuffer_fini - no longer needed now that we
refcount all fbs properly and only confusing.

v3: We actually still need to call unregister_private to remove the fb
from the idr and drop the idr reference - the final unref doesn't do
that. So much for remembering my own fb liftime rules. Reported by
Imre Deak.

Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v2)
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Touching the VGA registers risks a hard machine hang, at least on this
ivb machine after removing a conflicting efifb. This is more than likely
related to the discovery that VGA IO decode on the more recent PCH
platforms is terminally broken.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This has very little effect other than log the errors in case of failure,
and we then hope for the best.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Allocate this struct instead, so we can re-use another allocated
elsewhere if needed.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
[danvet: WARN_ON if there's no backing storage attached to an fb,
that's a bug.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We had 2 set of defines for the same register, so make it one.
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

And rename it to num_sprites as this value doesn't count the primary
plane.

This limit lives with num_pipes really, and now that dev_priv->info is
writable we can put it there instead.

While at it, introduce a intel_device_info_runtime_init() where we'll be
able to gather the device info fields at run-time.

v2: rename num_plane to num_sprites (Ville Syrjälä)
v3: rebase on top of latest drm-nightly

Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com> (for v2)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (for v2)
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

If we make sure that all the dev_priv->info usages are wrapped by
INTEL_INFO(), we can easily modify the ->info field to be structure and
not a pointer while keeping the const protection in the INTEL_INFO()
macro.

v2: Rebased onto latest drm-nightly
Suggested-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

With 20+ module parameters, I think referring to them via a struct
improves clarity over just having a bunch of globals. While at it, move
the parameter initialization and definitions into a new file
i915_params.c to reduce clutter in i915_drv.c.

Apart from the ill-named i915_enable_rc6, i915_enable_fbc and
i915_enable_ppgtt parameters, for which we lose the "i915_" prefix
internally, the module parameters now look the same both on the kernel
command line and in code. For example, "i915.modeset".

The downsides of the change are losing static on a couple of variables
and not having the initialization and module_param_named() right next to
each other. On the other hand, all module parameters are now defined in
one place at i915_params.c. Plus you can do this to find all module
parameter references:

$ git grep "i915\." -- drivers/gpu/drm/i915

v2:
- move the definitions into a new file
- s/i915_params/i915/
- make i915_try_reset i915.reset, for consistency
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>