It is more idiomatic to request all resources in the bus level probe,
this patch moves the request of the speaker thermal event IRQs from the
ASoC level probe into the bus level probe.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Whilst ultimately we would like to move all the clocking over to the
clock framework, as an intermediate step to get people going for now
gating the source clocks for SYSCLK/ASYNCCLK when they are configured
to come directly from an MCLK pin.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Tested-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Currently SYSCLK is attached to every compressed DAI as this follows the
pattern of attaching clocks to the chips inputs and outputs, however, it is
really the DSP that requires the clock here. As firmware download can be a
significant part of the path startup time for these devices occasionally it
would be desirable to download the firmware in advance of the path being
brought up.

To help facilitate this early firmware loading this patch attaches the
SYSCLK to the DSP preloader widget. This also saves us adding a new route
to SYSCLK every time a new compressed DAI is created.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Check for snd_soc_codec_driver structures that are only passed to
snd_soc_register_codec or memcpy (2nd arg), for which the corresponding
parameters are declared const.  Declare as const snd_soc_codec_driver
structures that have these properties.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct snd_soc_codec_driver i@p = { ... };

@ok@
identifier r.i;
expression e1,e2,e3;
position p;
@@
(
snd_soc_register_codec(e1,&i@p,e2,e3)
|
memcpy(e1,&i@p,e2)
)

@bad@
position p != {r.p,ok.p};
identifier r.i;
@@
i@p

@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
 struct snd_soc_codec_driver i = { ... };
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Acked-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The two clock domains are enabled based on each input and output of the
chip being connected to its respective clock domain. The ASRC however
can bridge the two domains and as such can function as an input/output
to either domain. The hardware also requires that both clocks are
enabled before the ASRC is. Ensure these constraints by linking the
ASRCs to both SYSCLK and ASYNCCLK.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

codec driver and component driver has duplicated callback functions,
and codec side functions are just copied to component side when
register timing. This was quick-hack, but no longer needed.
This patch moves these functions from codec driver to component driver.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The audio trace firmware on wm5102 only supports 4 channels correct
the DAI driver structure to reflect this.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The intent is for SYSCLK to be tied to all input and output widgets such
that it turns on whenever the chip is in use. It is not tied to the DRC
signal activity detect virtual outputs, whilst in practice this is
unlikely to cause an issue (as an input will likely also be powered up)
best to correct.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Ensure that the wm_adsp driver cleans up when the codec driver
is removed.
Signed-off-by: NRichard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

We request one of the DSP IRQs during CODEC probe, as such we should
free it during CODEC remove, this patch does so.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The thermal warning IRQs for the speaker are requested in CODEC probe
but never freed. This patch frees them in CODEC remove.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The Arizona CODECs support several rates that do not have simple defines
in ALSA. This patch adds support for SNDRV_PCM_RATE_KNOT so that users
can open stream at these rates. As part of this we should always set
constraints in arizona_startup, currently we only set the constraints if
we already have a clock to limit rates to that family of sample rates.
This patch updates this to set a constraint of all rates supported by
the chip if we do not already know which family of rates to limit to.
Finally we also reduce the list of rates supported in the constraints to
only include those that are supported on current parts.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

wm5102 also supports the audio trace firmware, this patch adds support
for this into the wm5102 driver.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The ADSP code should be agnostic of which CODEC it runs upon, currently
there is only one remaining part of the implementation that doesn't
follow this. When the DSP is booted on ADSP2 we read
ARIZONA_SYSTEM_CLOCK_1 and use that to set the initial speed for the DSP
clock. This patch factors that out into CODEC specific code, leaving the
ADSP code entirely CODEC agnostic.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

If we fail to add some DSPs or fail to add the controls we should call
wm_adsp2_codec_remove for all the cores we have already added. This
patch fixes this up on the wm5102 and wm5110.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Specifying unstable coefficients for the low/high pass filters can have
a severe impact on the audio. This patchs adds a stability check on the
coefficients written to the low/high pass filter block to prevent this.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Specifying unstable coefficients for the EQ can have a severe impact on
the audio. This patchs adds a stability check on the coefficients
written to the EQ, for this it is necessary to merge the mode control
and the coefficients as some coefficients may only be unstable with a
certain mode setting so it is ideal if these are always updated in sync.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The rate controls are codec-specific, it's not possible to
generically say what the range or the meaning of each control
is (or even if they exist at all) - that depends on the
particular codec.

This is currently being handled for Arizona codecs by putting
an Arizona-specific table of controls inside the wm_adsp driver.
This creates a dependency between wm_adsp and arizona.c, and is an
awkward solution if the ADSP is used in another family of codecs

Fix this by moving the Arizona-specific rate controls into the
Arizona codec drivers.
Signed-off-by: NRichard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Now that we have a codec_probe stage initialization in the wm_adsp
driver, we can make the wm_adsp driver create its own ALSA controls
instead of having that responsibility pushed to every codec driver.
Signed-off-by: NRichard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Currently the only init function in wm_adsp is called by the
codec driver early in its probe before the codec has been
registered with SOC.

This patch adds stubs for the codec_probe and codec_remove stages
and calls them from WM5102 and WM5110 codec drivers. This allows us
to hang anything that needs setup during the codec probe stage off
these functions without further modification of the codec drivers.
Signed-off-by: NRichard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

In theory the ADSP driver should not need to know anything
about the codec it is part of. But the WM5102 needs DVFS
control based on ADSP clocking speed. This was being handled
by bundling part of the knowledge of this into the ADSP driver.

This change moves this handling out of the ADSP driver and
into the WM5102 driver.
Signed-off-by: NRichard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The WM5102 and WM8997 codecs have an internal dynamic clock booster.
When this booster is active, the DCVDD voltage must be increased.
If all the currently active audio paths can run with the root SYSCLK
we can disable the booster, allowing us to turn down DCVDD voltage
to save power.

Previously this was being done by having the booster enable bit set
as a side-effect of the LDO1 regulator driver, which is unexpected
behaviour of a regulator and not compatible with using an external
regulator.  [Originally this was documented as a feature of the internal
LDO -- broonie]

This patch exports functions to handle the booster enable and
DCVDD voltage, with each relevant subsystem flagging whether it can
currently run without the booster. Note that these subsystems are
stateless and none of them are nestable, so there's no need for
reference counting, we only need a simple boolean for each subsystem
of whether their current condition could require the booster or will
allow us to turn the codec down to lower operating power.
Signed-off-by: NRichard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The dapm field of the snd_soc_codec struct is eventually going to be
removed, in preparation for this replace all manual access to codec->dapm
with snd_soc_codec_get_dapm().
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The Arizona codec drivers had an incorrect dB scaling for the
noise generator gain that started at 0dB and went upwards.
Actually the highest setting is 0dB.
Signed-off-by: NRichard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org

The earpiece on wm5102 is mono, thus there is no output 3R. Don't toggle
the volume update bits for this output, although worth noting that doing
so had no negative effects it is just redundant.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Save a bit of scheduling by coalescing all the output power up delays
into a single delay.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Give the output disable sequence a chance to fully complete, otherwise
there is a danger we may remove the clock before it is finished
resulting in a pop noise. The delay for each output must be cumulative
and these are coalesced into a single delay.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

This patch introduces the use of function put_unaligned_be16.

This is done using Coccinelle and semantic patch used is as follows:

@a@
typedef u16, __be16, uint16_t;
{u16,__be16,uint16_t} e16;
identifier tmp;
expression ptr;
expression y,e;
type T;
@@

- tmp = cpu_to_be16(y);

<+... when != tmp
(
- memcpy(ptr, (T)&tmp, \(2\|sizeof(u16)\|sizeof(__be16)\|sizeof(uint16_t)\|sizeof(e16)\));
+ put_unaligned_be16(y,ptr);
|
- memcpy(ptr, (T)&tmp, ...);
+ put_unaligned_be16(y,ptr);
)
...+>
? tmp = e

@@ type T; identifier a.tmp; @@

- T tmp;
...when != tmp
Signed-off-by: NVaishali Thakkar <vthakkar1994@gmail.com>
Acked-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
--
Changes Since v2:
   Make the patch compatible for current code

 sound/soc/codecs/wm5102.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
Signed-off-by: NMark Brown <broonie@kernel.org>

Commit d74bcaae (ASoC: wm5102: Move ultrasonic response settings
lock to the driver level) created a driver local mutex for protecting
the ultrasonic response settings but neglected to initialize that mutex,
causing loud complaints from lockep and potential runtime failures. Fix
this by initializing the mutex.
Signed-off-by: NMark Brown <broonie@kernel.org>
Acked-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>

The wm5102 driver currently uses the snd_soc_codec mutex to protect its
ultrasonic response settings from concurrent access. This patch moves this
lock to the driver level. This will allow us to eventually remove the
snd_soc_codec mutex.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

A platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Different playback and capture bits-per-sample
are not supported on the AIFs
Signed-off-by: NRichard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Controls for shaping the ultrasonic frequency response were introduced
in this commit:

commit 720630c002ffc7b0fa2ed5b3f4bfb36fd8f87ca6
ASoC: wm5102: Add controls to allow shaping of ultrasonic response

However, they mistakenly used snd_kcontrol_chip instead of
snd_soc_kcontrol_codec, which has replaced it now the framework is
moving to componentisation. This patch fixes this.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Add controls to allow custom shaping of the ultrasonic response. This
custom shaping can be turned on/off at runtime, although, it should be
noted that settings will not affect a currently open audio stream,
they will be applied when the next audio stream is started.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

SOC_VALUE_ENUM is deprecated and merely an alias for SOC_EMUM. Replace the
deprecated macros so we can eventually remove their definition.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

SND_SOC_DAPM_VALUE_MUX and SOC_DAPM_VALUE_ENUM are deprecated and merely an
alias for SND_SOC_DAPM_MUX and SOC_DAPM_ENUM. Replace the deprecated macros so
we can eventually remove their definition.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

Some thing Likes:

reproduce: make C=1 CF=-D__CHECK_ENDIAN__

sparse warnings: (new ones prefixed by >>)

>> sound/soc/codecs/wm8997.c:1084:15: sparse: symbol \
'wm8997_get_regmap' was not declared. Should it be static?
Signed-off-by: NXiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

As we can set the CODEC I/O while snd_soc_register_codec(), so the
calling of set_cache_io() from CODEC ASoC probe could be removed
entirely.

And then we can set the CODEC I/O in the device probe instead of
CODEC ASoC probe as earily as possible.
Signed-off-by: NXiubo Li <Li.Xiubo@freescale.com>
Acked-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Now that all users have been converted to regmap and the config.reg_bits
and config.val_bits can be setted by each user through regmap core API.
So these two params are redundant here.

Since the only control type that left is SND_SOC_REGMAP, so remove it. Drop
the control params and add struct regmap *regmap to simplify the code.
Signed-off-by: NXiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>