Makes no sense and complicates matters for pipelined tiling changes.
So don't allow it and return -EBUSY.

v2: Fix reference leak. Thanks to Owain Ainsworth for spotting this.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NEric Anholt <eric@anholt.net>

If we're both RGB and TMDS capable, we'll have set up one connector for
each.  When determining connectivity, require analog/digital state in
the EDID block to match analog/digital support in the connector.
Otherwise, both DVI and VGA will appear to be connected.
Signed-off-by: NAdam Jackson <ajax@redhat.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

Multifunction SDVO cards stopped working after 14571b4c, and would report
something that looked remarkably like an ADD2 SPD ROM instead of EDID.
This appears to be because DDC bus selection was utterly horked by that
commit; controlled_output was no longer always a single bit, so
intel_sdvo_select_ddc_bus would pick bus 0, which is (unsurprisingly)
the SPD ROM bus, not a DDC bus.

So, instead of that, let's just use the DDC bus the child device table
tells us to use.  I'm guessing at the bitmask and shifting from VBIOS
dumps, but it can't possibly be worse.

cf. https://bugzilla.redhat.com/584229Signed-off-by: NAdam Jackson <ajax@redhat.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

We'll turn off outputs etc at unload time, so don't unmap the registers
before doing it.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEric Anholt <eric@anholt.net>

Signed-off-by: NAdam Jackson <ajax@redhat.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

By idling the GPU and discarding everything we can when under extreme
memory pressure, the number of OOM-killer events is dramatically
reduced. For instance, this makes it possible to run
firefox-planet-gnome.trace again on my swapless 512MiB i915.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NEric Anholt <eric@anholt.net>

Spatial dither is better than nothing, but ST is even better.

(from ajax's followup message:)
  I noticed this with:

  http://ajax.fedorapeople.org/YellowFlower.jpg

  set as my desktop background in Gnome on a 1280x800 machine (in
  particular, a Sony Vaio VPCB1 with 6-bit panel and a rather bright black
  level).  Easiest way to test this is by poking at PIPEACONF with
  intel_reg_write directly:

  % sudo intel_reg_write 0x70008 0xc0000040 # no dither
  % sudo intel_reg_write 0x70008 0xc0000050 # spatial
  % sudo intel_reg_write 0x70008 0xc0000054 # ST

  I notice it especially strongly in the relatively flat dark area in the
  top left.  Closer than about 18" I can see a noticeable checkerboard
  pattern with plain spatial dithering.  ST smooths that out; I can still
  tell that it's lacking color precision, but it's not offensive.
Signed-off-by: NAdam Jackson <ajax@redhat.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

If the memory is not iomem we should not try to
ioremap it. Should fix :

https://bugs.freedesktop.org/show_bug.cgi?id=27822Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Tested-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

DVI-D doesn't have analog.  This matches the avivo behavior.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This should duplicate exactly what the ddx does for both
legacy and avivo.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

In the original code we used "j" as an iterator but we used "i" as an
index.

-               for (j = 0; j < i; j++)
-                       device_remove_file(&connector->kdev,
-                                          &connector_attrs[i]);

Smatch complained about that because "i" was potentially passed the end of
the array.  Which makes sense if we should be using "j" there.

I also thought that we should remove the files for &connector_attrs_opt1
but to do that I had to add separate iterators for &connector_attrs and
&connector_attrs_opt1.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This change makes the array larger, "MAX_SUPPORTED_TV_TIMING_V1_2" is 3
and the original size "MAX_SUPPORTED_TV_TIMING" is 2.

Also there were checks that were off by one.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Acked-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>

"agpmem" is never NULL here.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Cc: Eric Anholt <eric@anholt.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>

"fx->lock" is used as the index in "dev_priv->decoder_queue[fx->lock]"
which is an array of "VIA_NR_XVMC_LOCKS" elements.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Acked-by: NThomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Selecting the wrong or no CONFIG_AGP_* chipset can cause a NULL pointer
dereference when combined with CONFIG_DRM_RADEON_KMS and an old system
with a R100 AGP card (should effect other cards too).  The agp field
will be set to NULL if no suitable AGP chipset driver is loaded,
drm_agp_acquire already preforms a suitable NULL check so it can be used
directly.
Signed-off-by: NRobert Fitzsimons <robfitz@273k.net>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NMarek Olšák <maraeo@gmail.com>

Previous reset code leaded to computer hard lockup (need to unplug
the power too reboot the computer) on various configuration. This
patch change the reset code to avoid hard lockup. The GPU reset
is failing most of the time but at least user can log in remotely
or properly shutdown the computer.

Two issues were leading to hard lockup :
- Writting to the scratch register lead to hard lockup most likely
because the write back mecanism is in fuzy state after GPU lockup.
- Resetting the GPU memory controller and not reinitializing it
after leaded to hard lockup. We did only reinitialize in case of
successfull reset thus unsuccessfull reset quickly leaded to hard
lockup.
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Commit b4fe9454 ("drm/radeon: Fix
memory allocation failures in the preKMS command stream checking.")
added a regression in that it completely tossed the get_unaligned()
done by r300_scratch() which we added in commit
958a6f8c ("drm: radeon: Fix unaligned
access in r300_scratch().").

Put it back.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NMatt Turner <mattst88@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

When we call drm_vblank_off() at DPMS off time (to wake any clients so
they don't hang) we need to make sure interrupts are actually disabled.
If drm_vblank_off() gets called before the vblank usage timer expires,
it'll prevent the timer from disabling interrupts since it also clears
the vblank_enabled flag for the pipe.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>

My PIPE_CONTROL fix (just sent via Eric's tree) was buggy; I was
testing a whole set of patches together and missed a conversion to the
new HAS_PIPE_CONTROL macro, which will cause breakage on non-Ironlake
965 class chips.  Fortunately, the fix is trivial and has been tested.

Be sure to use the HAS_PIPE_CONTROL macro in i915_get_gem_seqno, or
we'll end up reading the wrong graphics memory, likely causing hangs,
crashes, or worse.
Reported-by: NZdenek Kabelac <zdenek.kabelac@gmail.com>
Reported-by: NToralf Förster <toralf.foerster@gmx.de>
Tested-by: NToralf Förster <toralf.foerster@gmx.de>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

DCE4 cards don't have an EnableYUV table.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Implements irq support for HDMI audio output. Now the polling timer
is only enabled if irq support isn't available.
Signed-off-by: NChristian König <deathsimple@vodafone.de>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Rework HDMI audio polling timer, only enable it when
at least one HDMI encoder needs it. Preparation for
replacing it with irq support.
Signed-off-by: NChristian König <deathsimple@vodafone.de>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Although these cards have 2 pipelines on the silicon only
the first passed the QA and the other should be disabled.

http://www.digital-daily.com/video/ati-radeon9800se/
http://www.rojakpot.com/showarticle.aspx?artno=101&pgno=1

agd5f: add some other SE cards as well; fix up kms
Signed-off-by: NTormod Volden <debian.tormod@gmail.com>
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

With evergreen this is bounded by num_crtc not by 0,1.
Signed-off-by: NDave Airlie <airlied@redhat.com>

Must have gotten broken during an earlier rebase.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Since 965, the hardware has supported the PIPE_CONTROL command, which
provides fine grained GPU cache flushing control.  On recent chipsets,
this instruction is required for reliable interrupt and sequence number
reporting in the driver.

So add support for this instruction, including workarounds, on Ironlake
and Sandy Bridge hardware.

https://bugs.freedesktop.org/show_bug.cgi?id=27108Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NEric Anholt <eric@anholt.net>

This keeps the memory manager from complaining when we take it down.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEric Anholt <eric@anholt.net>

Eric mentioned on irc this patch was bad, so revert it.

This reverts commit fb8b5a39.
Acked-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Drivers may use vblank calls now (e.g. drm_vblank_off) in their unload
paths, so don't clean up the vblank related structures until after
driver unload.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NKristian Høgsberg <krh@bitplanet.net>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This patch enable the use of unmappable VRAM thanks to
previous TTM infrastructure change.

V2 update after io_mem_reserve/io_mem_free callback balancing
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

All TTM driver have been converted to new io_mem_reserve/free
interface which allow driver to choose and return proper io
base, offset to core TTM for ioremapping if necessary. This
patch remove what is now deadcode.

V2 adapt to match with change in first patch of the patchset
V3 update after io_mem_reserve/io_mem_free callback balancing
V4 adjust to minor cleanup
V5 remove the needs ioremap flag
V6 keep the ioremapping facility in TTM

[airlied- squashed driver removals in here also]
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Reviewed-by: NThomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This add the support for the new fault callback, does change anything
from driver point of view.

Improvement: store the aperture base in a variable so that we don't
call a function to get it on each fault.

Patch hasn't been tested.

V2 don't derefence bo->mem.mm_node as it's not NULL only for
   VRAM or GTT
V3 update after io_mem_reserve/io_mem_free callback balancing
V4 callback has to ioremap
V5 ioremap is done by TTM
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Reviewed-by: NThomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This add the support for the new fault callback, does change anything
from driver point of view, thought it should allow nouveau to add
support for unmappable VRAM.

Improvement: store the aperture base in a variable so that we don't
call a function to get it on each fault.

Patch hasn't been tested on any hw.

V2 don't derefence bo->mem.mm_node as it's not NULL only for
   VRAM or GTT
V3 update after io_mem_reserve/io_mem_free callback balancing
V4 callback has to ioremap
V5 ioremap is done by ttm
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This add the support for the new fault callback and also the
infrastructure for supporting unmappable VRAM.

V2 validate BO with no_wait = true
V3 don't derefence bo->mem.mm_node as it's not NULL only for
   VRAM or GTT
V4 update to splitted no_wait ttm change
V5 update to new balanced io_mem_reserve/free change
V6 callback is responsible for iomapping memory
V7 move back iomapping to ttm
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

On fault the driver is given the opportunity to perform any operation
it sees fit in order to place the buffer into a CPU visible area of
memory. This patch doesn't break TTM users, nouveau, vmwgfx and radeon
should keep working properly. Future patch will take advantage of this
infrastructure and remove the old path from TTM once driver are
converted.

V2 return VM_FAULT_NOPAGE if callback return -EBUSY or -ERESTARTSYS
V3 balance io_mem_reserve and io_mem_free call, fault_reserve_notify
   is responsible to perform any necessary task for mapping to succeed
V4 minor cleanup, atomic_t -> bool as member is protected by reserve
   mecanism from concurent access
V5 the callback is now responsible for iomapping the bo and providing
   a virtual address this simplify TTM and will allow to get rid of
   TTM_MEMTYPE_FLAG_NEEDS_IOREMAP
V6 use the bus addr data to decide to ioremap or this isn't needed
   but we don't necesarily need to ioremap in the callback but still
   allow driver to use static mapping
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Reviewed-by: NThomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Luckily the change is quite a little bit less invasive than I've
feared.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Thanks to the to_intel_bo helper, this change is rather trivial.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Just embed it and adjust the pointers, No other changes (that's
for later patches).
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Just preparation, no functional change.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NDave Airlie <airlied@redhat.com>