- 09 5月, 2007 2 次提交
-
-
由 Juha Yrjola 提交于
Add DMA IRQ sanity checks Signed-off-by: NJuha Yrjola <juha.yrjola@solidboot.com> Signed-off-by: NTony Lindgren <tony@atomide.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 David Brownell 提交于
Minor GPIO cleanups: remove needless #include, and omap_gpio_init() should be __init, as well as all the board init code calling it. Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net> Signed-off-by: NTony Lindgren <tony@atomide.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 05 5月, 2007 8 次提交
-
-
由 David Brownell 提交于
Fix oops in omap16xx mpuio suspend/resume code; field wasn't initialized Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net> Signed-off-by: NTony Lindgren <tony@atomide.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 David Brownell 提交于
GPIO and MPUIO wake updates: - Hook MPUIOs into the irq wakeup framework too. This uses a platform device to update irq enables during system sleep states, instead of a sys_device, since the latter is no longer needed for such things. - Also forward enable/disable irq wake requests to the relevant GPIO controller, so the top level IRQ dispatcher can (eventually) handle these wakeup events automatically if more than one GPIO pin needs to be a wakeup event source. - Minor tweak to the 24xx non-wakeup gpio stuff: no need to check such read-only data under the spinlock. This assumes (maybe wrongly?) that only 16xx can do GPIO wakeup; without a 15xx I can't test such stuff. Also this expects the top level IRQ dispatcher to properly handle requests to enable/disable irq wake, which is currently known to be wrong: omap1 saves the flags but ignores them, omap2 doesn't even save it. (Wakeup events are, wrongly, hardwired in the relevant mach-omapX/pm.c file ...) So MPUIO irqs won't yet trigger system wakeup. Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net> Signed-off-by: NTony Lindgren <tony@atomide.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 David Brownell 提交于
Speedup and shrink GPIO irq handling code, by using a pointer that's available in the irq_chip structure instead of calling the get_gpio_bank() function. On OMAP1 this saves 44 words, most of which were in IRQ critical path methods. Hey, every few instructions help. Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net> Signed-off-by: NTony Lindgren <tony@atomide.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Syed Mohammed Khasim 提交于
This patch adds minimal OMAP2430 support to plat-omap files to get the kernel booting on 2430SDP. Signed-off-by: NSyed Mohammed Khasim <x0khasim@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 David Brownell 提交于
More GPIO/IRQ cleanup: - compile-time removal of much useless code * mpuio support on non-OMAP1. * 15xx/730/24xx gpio support on 1610 * 15xx/730/16xx gpio support on 24xx * etc - remove all BUG() calls, which are always bad news ... replaced some with normal fault reports for that call, others with WARN_ON(1). - small mpuio bugfix: add missing set_type() method Oh, and fix a minor merge issue: inode->u.generic_ip is now gone. Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net> Signed-off-by: NTony Lindgren <tony@atomide.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 David Brownell 提交于
Add some GPIO debug support: /sys/kernel/debug/omap_gpio dumps the state of all GPIOs that have been claimed, including basic IRQ info if relevant. Tested on 24xx, 16xx. Includes minor bugfixes: recording IRQ trigger mode (this should probably be a genirq patch), adding missing space to non-wakeup warning Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net> Signed-off-by: NTony Lindgren <tony@atomide.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Juha Yrjola 提交于
Some GPIOs on OMAP2420 do not have wakeup capabilities. If these GPIOs are configured as IRQ sources, spurious interrupts will be generated each time the core domain enters retention. Signed-off-by: NJuha Yrjola <juha.yrjola@solidboot.com> Signed-off-by: NTony Lindgren <tony@atomide.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Juha Yrjola 提交于
Enable 24xx GPIO autoidling Signed-off-by: NJuha Yrjola <juha.yrjola@solidboot.com> Signed-off-by: NTony Lindgren <tony@atomide.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 22 4月, 2007 5 次提交
-
-
由 Russell King 提交于
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Russell King 提交于
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Russell King 提交于
Lots of places in arch/arm were needlessly including linux/ptrace.h, resumably because we used to pass a struct pt_regs to interrupt handlers. Now that we don't, all these ptrace.h includes are redundant. Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Russell King 提交于
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Russell King 提交于
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 20 4月, 2007 14 次提交
-
-
由 Linus Torvalds 提交于
This reverts commit 60cba200. It's been linked to lockups of the e1000 hardware, see for example https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=229603 but it's likely that the commit itself is not really introducing the bug, but just allowing an unrelated problem to rear its ugly head (ie one current working theory is that the code exposes us to a hardware race condition by decreasing the amount of time we spend in each NAPI poll cycle). We'll revert it until root cause is known. Intel has a repeatable reproduction on two different machines and bus traces of the hardware doing something bad. Acked-by: NJesse Brandeburg <jesse.brandeburg@intel.com> Cc: Jeff Garzik <jeff@garzik.org> Cc: David S. Miller <davem@davemloft.net> Cc: Greg KH <gregkh@suse.de> Cc: Dave Jones <davej@redhat.com> Cc: Auke Kok <auke-jan.h.kok@intel.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Linus Torvalds 提交于
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev: pata_sis: Fix oops on boot
-
由 Alan Cox 提交于
A small number of SiS setups require special handling (not many judging by how long this dumb bug survived). A couple of Fedora 7 devel testers hit an Oops on pata_sis loading which is caused by terminal confusion between chipset as 'the chipset we have found' and chipset as 'array iterator' Signed-off-by: NAlan Cox <alan@redhat.com> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Stephen Hemminger 提交于
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Stephen Hemminger 提交于
The Yukon FE (100mbit only) chips do not support large packets. Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Stephen Hemminger 提交于
The Yukon EC Ultra chips have transmit settings for store and forward and PCI buffering. By setting these appropriately, normal performance goes from 750Mbytes/sec to 940Mbytes/sec (non-jumbo). It is also possible to do Jumbo mode, but it means turning off TSO and checksum offload so the performance gets worse. There isn't enough buffering for checksum offload to work. Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Stephen Hemminger 提交于
Need to make sure and disable ASF on all chip types. Otherwise, there may be random reboots. Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Stephen Hemminger 提交于
There should never be descriptor error unless hardware or driver is buggy. But if an error occurs, print useful information, clear irq, and recover. Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Stephen Hemminger 提交于
This device is having all sorts of problems that lead to data corruption and system instability. It gets receive status and data out of order, it generates descriptor and TSO errors, etc. Until the problems are resolved, it should not be used by anyone who cares about there system. Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Dave Jiang 提交于
Gianfar needs crc32 to be selected to compile. Signed-off-by: NDave Jiang <djiang@mvista.com> -- drivers/net/Kconfig | 1 + 1 files changed, 1 insertions(+), 0 deletions(-) -- Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Linas Vepstas 提交于
The basic structure of "normal" UDP/IP/Ethernet frames (that actually work): - It starts with the Ethernet header (dest MAC, src MAC, etc.) - The next part is occupied by the IP header (version info, length of packet, id=0, fragment offset=0, checksum, from / to address, etc.) - Then comes the UDP header (src / dest port, length, checksum) - Actual payload - Ethernet checksum Now what's different for IP fragment: - The IP header has id set to some value (same for all fragments), offset is set appropriately (i.e. 0 for first fragment, following according to size of other fragments), size is the length of the frame. - UDP header is unchanged. I.e. length is according to full UDP datagram, not just the part within the actual frame! But this is only true within the first frame: all following frames don't have a valid UDP-header at all. The spidernet silicon seems to be quite intelligent: It's able to compute (IP / UDP / Ethernet) checksums on the fly and tests if frames are conforming to RFC -- at least conforming to RFC on complete frames. But IP fragments are different as explained above: I.e. for IP fragments containing part of a UDP datagram it sees incompatible length in the headers for IP and UDP in the first frame and, thus, skips this frame. But the content *is* correct for IP fragments. For all following frames it finds (most probably) no valid UDP header at all. But this *is* also correct for IP fragments. The Linux IP-stack seems to be clever in this point. It expects the spidernet to calculate the checksum (since the module claims to be able to do so) and marks the skb's for "normal" frames accordingly (ip_summed set to CHECKSUM_HW). But for the IP fragments it does not expect the driver to be capable to handle the frames appropriately. Thus all checksums are allready computed. This is also flaged within the skb (ip_summed set to CHECKSUM_NONE). Unfortunately the spidernet driver ignores that hints. It tries to send the IP fragments of UDP datagrams as normal UDP/IP frames. Since they have different structure the silicon detects them the be not "well-formed" and skips them. The following one-liner against 2.6.21-rc2 changes this behavior. If the IP-stack claims to have done the checksumming, the driver should not try to checksum (and analyze) the frame but send it as is. Signed-off-by: NNorbert Eicker <n.eicker@fz-juelich.de> Signed-off-by: NLinas Vepstas <linas@austin.ibm.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Divy Le Ray 提交于
Remove assumption that PHY interrupts use GPIOs 3 and 5. Deal with PHY interrupts connected to any GPIO pins. Signed-off-by: NDivy Le Ray <divy@chelsio.com> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Divy Le Ray 提交于
Reuse the incoming skb when a clientless abort req is recieved. The release of RDMA connections HW resources might be deferred in low memory situations. Ensure that no further activity is passed up to the RDMA driver for these connections. Signed-off-by: NDivy Le Ray <divy@chelsio.com> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm由 Linus Torvalds 提交于
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm: KVM: Fix off-by-one when writing to a nonpae guest pde
-
- 19 4月, 2007 5 次提交
-
-
由 Avi Kivity 提交于
Nonpae guest pdes are shadowed by two pae ptes, so we double the offset twice: once to account for the pte size difference, and once because we need to shadow pdes for a single guest pde. But when writing to the upper guest pde we also need to truncate the lower bits, otherwise the multiply shifts these bits into the pde index and causes an access to the wrong shadow pde. If we're at the end of the page (accessing the very last guest pde) we can even overflow into the next host page and oops. Signed-off-by: NAvi Kivity <avi@qumranet.com>
-
由 Denis Lunev 提交于
There is a race between netlink_dump_start() and netlink_release() that can lead to the situation when a netlink socket with non-zero callback is freed. Here it is: CPU1: CPU2 netlink_release(): netlink_dump_start(): sk = netlink_lookup(); /* OK */ netlink_remove(); spin_lock(&nlk->cb_lock); if (nlk->cb) { /* false */ ... } spin_unlock(&nlk->cb_lock); spin_lock(&nlk->cb_lock); if (nlk->cb) { /* false */ ... } nlk->cb = cb; spin_unlock(&nlk->cb_lock); ... sock_orphan(sk); /* * proceed with releasing * the socket */ The proposal it to make sock_orphan before detaching the callback in netlink_release() and to check for the sock to be SOCK_DEAD in netlink_dump_start() before setting a new callback. Signed-off-by: NDenis Lunev <den@openvz.org> Signed-off-by: NKirill Korotaev <dev@openvz.org> Signed-off-by: NPavel Emelianov <xemul@openvz.org> Acked-by: NPatrick McHardy <kaber@trash.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Olaf Kirch 提交于
This patch fixes an oops first reported in mid 2006 - see http://lkml.org/lkml/2006/8/29/358 The cause of this bug report is that when an error is signalled on the socket, irda_recvmsg_stream returns without removing a local wait_queue variable from the socket's sk_sleep queue. This causes havoc further down the road. In response to this problem, a patch was made that invoked sock_orphan on the socket when receiving a disconnect indication. This is not a good fix, as this sets sk_sleep to NULL, causing applications sleeping in recvmsg (and other places) to oops. This is against the latest net-2.6 and should be considered for -stable inclusion. Signed-off-by: NOlaf Kirch <olaf.kirch@oracle.com> Signed-off-by: NSamuel Ortiz <samuel@sortiz.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Vlad Yasevich 提交于
The way partial delivery is currently implemnted, it is possible to intereleave a message (either from another steram, or unordered) that is not part of partial delivery process. The only way to this is for a message to not be a fragment and be 'in order' or unorderd for a given stream. This will result in bypassing the reassembly/ordering queues where things live duing partial delivery, and the message will be delivered to the socket in the middle of partial delivery. This is a two-fold problem, in that: 1. the app now must check the stream-id and flags which it may not be doing. 2. this clearing partial delivery state from the association and results in ulp hanging. This patch is a band-aid over a much bigger problem in that we don't do stream interleave. Signed-off-by: NVlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Make sure to actually assign the determined mode to rq->sadb_x_ipsecrequest_mode. Noticed by Joe Perches. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 18 4月, 2007 6 次提交
-
-
由 Linus Torvalds 提交于
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: [BRIDGE]: Unaligned access when comparing ethernet addresses [SCTP]: Unmap v4mapped addresses during SCTP_BINDX_REM_ADDR operation. [SCTP]: Fix assertion (!atomic_read(&sk->sk_rmem_alloc)) failed message [NET]: Set a separate lockdep class for neighbour table's proxy_queue [NET]: Fix UDP checksum issue in net poll mode. [KEY]: Fix conversion between IPSEC_MODE_xxx and XFRM_MODE_xxx. [NET]: Get rid of alloc_skb_from_cache
-
由 Linus Torvalds 提交于
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband: IB/mthca: Fix data corruption after FMR unmap on Sinai
-
git://one.firstfloor.org/home/andi/git/linux-2.6由 Linus Torvalds 提交于
* 'for-linus' of git://one.firstfloor.org/home/andi/git/linux-2.6: [PATCH] x86: Fix potential overflow in perfctr reservation [PATCH] x86: Fix gcc 4.2 _proxy_pda workaround
-
由 Olof Johansson 提交于
* Last write during i2c_xfer is of the wrong byte (off-by-1). * Read length is wrong for some of the reads (mistakenly used the PEC version) Signed-off-by: NOlof Johansson <olof@lixom.net> Signed-off-by: NJean Delvare <khali@linux-fr.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Jean Delvare 提交于
Looks like a local change I made to be able to test-compile the i2c-pasemi driver leaked upstream. Signed-off-by: NJean Delvare <khali@linux-fr.org> Acked-by: NOlof Johansson <olof@lixom.net> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Jean Delvare 提交于
Users have been complaining about the w83627ehf driver flooding their logs with debug messages like: w83627ehf 9191-0a10: Increasing fan 4 clock divider from 64 to 128 or: w83627ehf 9191-0290: Increasing fan 4 clock divider from 4 to 8 The reason is that we failed to actually write the LSB of the encoded clock divider value for that fan, causing the next read to report the same old value again and again. Additionally, the fan number was improperly reported, making the bug harder to find. Signed-off-by: NJean Delvare <khali@linux-fr.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-