Update Kconfig file to enable I2S,PCM audio for wm8994 and spdif on all
samsung platforms.
Signed-off-by: NSangsu Park <sangsu4u.park@samsung.com>
Signed-off-by: NSangbeom Kim <sbkim73@samsung.com>
Signed-off-by: NPadmavathi Venna <padma.v@samsung.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Add the basic device tree based lookup.
Signed-off-by: NPadmavathi Venna <padma.v@samsung.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Add support for device based discovery.
Signed-off-by: NPadmavathi Venna <padma.v@samsung.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

I2S module need to be reset after S2R. Keeping the S/W rst
control part in resume didn't help in playing audio after resume.
So this patch adds S/W RST control part in startup function which
gets triggered for every new audio stream playback.
Signed-off-by: NPadmavathi Venna <padma.v@samsung.com>
Signed-off-by: NR. Chandrasekar <rcsekar@samsung.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

All Samsung SoCs has max 3 i2s controllers. So the i2s secondary fifo
interface device id was named as samsung-i2s.4. Renaming this to
"samsung-i2s-sec" to support device tree in i2s driver.
Signed-off-by: NPadmavathi Venna <padma.v@samsung.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Otherwise we won't run correctly on systems that require this for larger
data transfers.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org

These are not supported
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org

These are not supported.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org

These are not supported.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

When probing aux_dev, initializing is as below:
device_initialize()
device_add()

So when remove aux_dev, we need do as below:
device_del()
device_put()
Otherwise, the rtd_release() will not be called.

So here using device_unregister() to replace device_del(),
like the action in soc_remove_link_dais().
Signed-off-by: Nliu chuansheng <chuansheng.liu@intel.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

After called device_initialize(), even device_add() returns
error, we still need use the put_device() to release the reference
to call rtd_release(), which will do the free() action.
Signed-off-by: Nliu chuansheng <chuansheng.liu@intel.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

In the case of no-match, return -EINVAL instead of 0.

Since we assign i to ret in the for loop, ret always less than
ARRAY_SIZE(clk_map_table). Thus remove the boundary checking for ret.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Update lm49453_reg_defs values as per LM49453 HW revision-B
Signed-off-by: NM R Swami Reddy <mr.swami.reddy@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Add adc, mic, sidetone volume ranges and appropriately added the controls.
Fix the DAC HP/EP/LS/LO/HA maximum gain values.
Signed-off-by: NMR Swami Reddy <mr.swami.reddy@ti.com>
Tested-by: NVinod Koul <vinod.koul@intel.com>

--
 sound/soc/codecs/lm49453.c |   43 ++++++++++++++++++++++++-------------------
 1 files changed, 24 insertions(+), 19 deletions(-)
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The FLL source constants were numbered as a simple enumeration but were
being used in the code as direct values to be written to the registers.
Renumber the constants to reflect the usage.
Reported-by: NRyo Tsutsui <Ryo.Tsutsui@wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org

ARIZONA_AIF1_RATE_MASK is 0x7800 /* AIF1_RATE - [14:11] */
Thus we need left shift ARIZONA_AIF1_RATE_SHIFT when setting aif1 rate.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org

The mode variable is either 0 or 1.
To update mode setting, the mask should be BIT(0) rather than BIT(1).
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Tested-by: NOmair M. Abdullah <omair.m.abdullah@intel.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

sgtl5000 microphone gain only has 2 bits of resolution, so maximum value is 3.

From Eric Nelson:
"We also found that for the microphones we have here (commodity PC boom mics) a
default value of 2 for the gain gives the best results."

So change the default microphone gain as well.
Signed-off-by: NEric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

commit 9bde4f0b (ASoC: core: Fix SOC_DOUBLE_RANGE() macros) introduced
the following build warning:

sound/soc/soc-core.c:2999:6: warning: unused variable 'ret' [-Wunused-variable]

Remove the unused 'ret' variable.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

According to the defines in wm2200.h:
/*
 * R1284 (0x504) - Audio IF 1_5
 */

We should not left shift 1 bit for fmt_val when setting dai format.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org

Although we've had macros defining double _RANGE controls for a while now
they've not actually been backed up properly by the implementation, it's
treated everything as mono. Fix that by implementing the handling in the
stereo controls, ensuring that the mono controls don't mistakenly get
treated as stereo.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

Both the mask and mode settings are wrong in current code.

According to the datasheet:

S2PCFG0 (0x0A)
BIT[3:1] DATA_FORMAT
        serial interface protocol format:
        000: left Justified
        001: I2S (default)
        010: right justified
        100: PCM no delay
        101: PCM delay
        111: DSP

Thus fixes the defines for LEFT_J_DATA_FORMAT, I2S_DATA_FORMAT, and
RIGHT_J_DATA_FORMAT.
Also adds define for DATA_FORMAT_MSK.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Acked-by: NRajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org

When front-end PCM session is in paused state, back-end
PCM session will be put in paused state as well if given
front-end PCM session is the only client of given back-end.
Then, application closes front-end PCM session, DPCM
framework will not allow back-end enters HW_FREE state
so back-end will never get shutdown completely.
Signed-off-by: NPatrick Lai <plai@codeaurora.org>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org

pop_wait is used to determine if a deferred playback close
needs to be cancelled when the a PCM is open or if after
the power-down delay expires it needs to run. pop_wait is
associated with the CODEC DAI, so the CODEC DAI must be
unique. This holds true for most CODECs, except for the
dummy CODEC and its DAI.

In DAI links with non-unique dummy CODECs (e.g. front-ends),
pop_wait can be overwritten by another DAI link using also a
dummy CODEC. Failure to cancel a deferred close can cause
mute due to the DAPM STOP event sent in the deferred work.

One scenario where pop_wait is overwritten and causing mute
is below (where hw:0,0 and hw:0,1 are two front-ends with
default pmdown_time = 5 secs):

aplay /dev/urandom -D hw:0,0 -c 2 -r 48000 -f S16_LE -d 1
sleep 1
aplay /dev/urandom -D hw:0,1 -c 2 -r 48000 -f S16_LE -d 3 &
aplay /dev/urandom -D hw:0,0 -c 2 -r 48000 -f S16_LE

Since CODECs may not be unique, pop_wait is moved to the PCM
runtime structure. Creating separate dummy CODECs for each
DAI link can also solve the problem, but at this point it's
only pop_wait variable in the CODEC DAI that has negative
effects by not being unique.
Signed-off-by: NMisael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Don't wrap log messages over multiple lines, it makes them hard to grep
for.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Since VSP only has one power bit, only provide one DAPM widget.
Signed-off-by: NPaul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Add power down delays between setting PDN and MCLKDIS for spk amp, spklo amp, and ear amp.
Signed-off-by: NPaul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NPaul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The 'addr' field of the sigma_action struct is stored as big endian in the
firmware file.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org

CONFIG_HOTPLUG is going away as an option.  As result the __dev*
markings will be going away.

Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

CONFIG_HOTPLUG is going away as an option.  As result the __dev*
markings will be going away.

Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

CONFIG_HOTPLUG is going away as an option.  As result the __dev*
markings will be going away.

Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

CONFIG_HOTPLUG is going away as an option.  As result the __dev*
markings will be going away.

Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

CONFIG_HOTPLUG is going away as an option.  As result the __dev*
markings will be going away.

Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

CONFIG_HOTPLUG is going away as an option.  As result the __dev*
markings will be going away.

Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

CONFIG_HOTPLUG is going away as an option.  As result the __dev*
markings will be going away.

Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

CONFIG_HOTPLUG is going away as an option.  As result the __dev*
markings will be going away.

Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

CONFIG_HOTPLUG is going away as an option.  As result the __dev*
markings will be going away.

Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>