- 09 5月, 2012 1 次提交
-
-
由 Ben Hutchings 提交于
If RSS is disabled on the PF (efx->n_rx_channels == 1) we try to set up the indirection table so that VFs can use it, setting efx->rss_spread = efx_vf_size(efx). But if SR-IOV was disabled at compile time, this evaluates to 0 and we end up dividing by zero when initialising the table. I considered changing the fallback definition of efx_vf_size() to return 1, but its value is really meaningless if we are not going to enable VFs. Therefore add a condition of efx_sriov_wanted(efx) in efx_probe_interrupts(). Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
-
- 08 5月, 2012 1 次提交
-
-
由 Johannes Berg 提交于
Neither compare_ether_addr() nor compare_ether_addr_64bits() (as it can fall back to the former) have comparison semantics like memcmp() where the sign of the return value indicates sort order. We had a bug in the wireless code due to a blind memcmp replacement because of this. A cursory look suggests that the wireless bug was the only one due to this semantic difference. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 07 5月, 2012 2 次提交
-
-
由 Bjørn Mork 提交于
Some RNDIS devices include a bogus CDC Union descriptor pointing to non-existing interfaces. The RNDIS code is already prepared to handle devices without a CDC Union descriptor by hardwiring the driver to use interfaces 0 and 1, which is correct for the devices with the bogus descriptor as well. So we can reuse the existing workaround. Cc: Markus Kolb <linux-201011@tower-net.de> Cc: Iker Salmón San Millán <shaola@esdebian.org> Cc: Jonathan Nieder <jrnieder@gmail.com> Cc: Oliver Neukum <oliver@neukum.org> Cc: 655387@bugs.debian.org Cc: stable@vger.kernel.org Signed-off-by: NBjørn Mork <bjorn@mork.no> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ariel Elior 提交于
This is a bug fix for an "interface fails to load" issue. The issue occurs when bnx2x driver loads after UNDI driver was previously loaded over the chip. In such a scenario the UNDI driver is loaded and operates in the pre-boot kernel, within its own specific host memory address range. When the pre-boot stage is complete, the real kernel is loaded, in a new and distinct host memory address range. The transition from pre-boot stage to boot is asynchronous from UNDI point of view. A race condition occurs when UNDI driver triggers a DMAE transaction to valid host addresses in the pre-boot stage, when control is diverted to the real kernel. This results in access to illegal addresses by our HW as the addresses which were valid in the preboot stage are no longer considered valid. Specifically, the 'was_error' bit in the pci glue of our device is set. This causes all following pci transactions from chip to host to timeout (in accordance to the pci spec). Signed-off-by: NAriel Elior <ariele@broadcom.com> Signed-off-by: NEilon Greenstein <eilong@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 05 5月, 2012 1 次提交
-
- 04 5月, 2012 16 次提交
-
-
由 Andrei Emeltchenko 提交于
Silence sparse warnings shown below: ... drivers/net/ethernet/intel/e1000/e1000_main.c:3435:17: warning: cast to restricted __le64 drivers/net/ethernet/intel/e1000/e1000_main.c:3435:17: warning: cast to restricted __le64 ... Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com> Tested-by: NAaron Brown <aaron.f.brown@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 John Fastabend 提交于
igb and ixgbe incorrectly call netdev_tx_reset_queue() from i{gb|xgbe}_clean_tx_ring() this sort of works in most cases except when the number of real tx queues changes. When the number of real tx queues changes netdev_tx_reset_queue() only gets called on the new number of queues so when we reduce the number of queues we risk triggering the watchdog timer and repeated device resets. So this is not only a cosmetic issue but causes real bugs. For example enabling/disabling DCB or FCoE in ixgbe will trigger this. CC: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com> Tested-by: NJohn Bishop <johnx.bishop@intel.com> Tested-by: NAaron Brown <aaron.f.brown@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6由 Linus Torvalds 提交于
Pull second set of MFD fixes from Samuel Ortiz: "This time we only have a one liner fixing an omap-usb build error." * tag 'mfd-for-linus-3.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: mfd: Fix build breakage in omap-usb-host.c
-
由 Linus Torvalds 提交于
* efi-vars: efivars: Improve variable validation
-
由 Matthew Garrett 提交于
Ben Hutchings pointed out that the validation in efivars was inadequate - most obviously, an entry with size 0 would server as a DoS against the kernel. Improve this based on his suggestions. Signed-off-by: NMatthew Garrett <mjg@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev由 Linus Torvalds 提交于
Pull libata fixes from Jeff Garzik: 1) Fix regression that could cause a misdiagnosis, which in turn could lead to an erroneous 3.0 Gbps -> 1.5 downshift, particularly when hotplug and suspend/resume is involved. 2) Fix a regression that led to ata%d controller ids being numbered one larger than in <= 3.4-rc3 (oh, the horror!). Controller ids should now be as expected. 3) add some DT, PCI id's 4) ata/pata_arasan_cf: minor cpp fixing/cleaning * tag 'tag/upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: ata: ahci_platform: Add synopsys ahci controller in DT's compatible list ata/pata_arasan_cf: Move arasan_cf_pm_ops out of #ifdef, #endif macros libata: init ata_print_id to 0 ahci: Detect Marvell 88SE9172 SATA controller libata: skip old error history when counting probe trials
-
git://git.pengutronix.de/git/wsa/linux由 Linus Torvalds 提交于
Pull i2c embedded fixes from Wolfram Sang: "Here are some typical i2c driver bugfixes for 3.4. Missed clock handling, improper timeout fixes, hardware wrokarounds... All patches have been in linux-next for a few days, too." * 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux: i2c: mxs: disable QUEUE when sending is done i2c: mxs: handle spurious interrupt i2c-eg20t: Modify MODULE_AUTHOR's email address i2c-eg20t: change timeout value 50msec to 1000msec i2c: tegra: Add delay before resetting the controller after NACK i2c: pnx: Disable clk in suspend
-
git://people.freedesktop.org/~airlied/linux由 Linus Torvalds 提交于
Pull drm fixes from Dave Airlie: "Just some regression fixes from Ben along with a variable that gcc failed to spot is uninitialised." * 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: nouveau: initialise has_optimus variable. drm/nv10/gpio: fix thinko in mask for gpio lines 2-9 nvc0/fb: shut up PMFB interrupt after the first occurrence drm/nouveau/hdmi: use correct hdmi regs for nvaa/nvac drm/nouveau/bios: fix regression on some nv4x board
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net由 Linus Torvalds 提交于
Pull networking fixes from David Miller: 1) Transfer padding was wrong for full-speed USB in ASIX driver, fix from Ingo van Lil. 2) Propagate the negative packet offset fix into the PowerPC BPF JIT. From Jan Seiffert. 3) dl2k driver's private ioctls were letting unprivileged tasks make MII writes and other ugly bits like that. Fix from Jeff Mahoney. 4) Fix TX VLAN and RX packet drops in ucc_geth, from Joakim Tjernlund. 5) OOPS and network namespace fixes in IPVS from Hans Schillstrom and Julian Anastasov. 6) Fix races and sleeping in locked context bugs in drop_monitor, from Neil Horman. 7) Fix link status indication in smsc95xx driver, from Paolo Pisati. 8) Fix bridge netfilter OOPS, from Peter Huang. 9) L2TP sendmsg can return on error conditions with the socket lock held, oops. Fix from Sasha Levin. 10) udp_diag should return meaningful values for socket memory usage, from Shan Wei. 11) Eric Dumazet is so awesome he gets his own section: Socket memory cgroup code (I never should have applied those patches, grumble...) made erroneous changes to sk_sockets_allocated_read_positive(). It was changed to use percpu_counter_sum_positive (which requires BH disabling) instead of percpu_counter_read_positive (which does not). Revert back to avoid crashes and lockdep warnings. Adjust the default tcp_adv_win_scale and tcp_rmem[2] values to fix throughput regressions. This is necessary as a result of our more precise skb->truesize tracking. Fix SKB leak in netem packet scheduler. 12) New device IDs for various bluetooth devices, from Manoj Iyer, AceLan Kao, and Steven Harms. 13) Fix command completion race in ipw2200, from Stanislav Yakovlev. 14) Fix rtlwifi oops on unload, from Larry Finger. 15) Fix hard_mtu when adjusting hard_header_len in smsc95xx driver. From Stephane Fillod. 16) ehea driver registers it's IRQ before all the necessary state is setup, resulting in crashes. Fix from Thadeu Lima de Souza Cascardo. 17) Fix PHY connection failures in davinci_emac driver, from Anatolij Gustschin. 18) Missing break; in switch statement in bluetooth's hci_cmd_complete_evt(). Fix from Szymon Janc. 19) Fix queue programming in iwlwifi, from Johannes Berg. 20) Interrupt throttling defaults not being actually programmed into the hardware, fix from Jeff Kirsher and Ying Cai. 21) TLAN driver SKB encoding in descriptor busted on 64-bit, fix from Benjamin Poirier. 22) Fix blind status block RX producer pointer deref in TG3 driver, from Matt Carlson. 23) Promisc and multicast are busted on ehea, fixes from Thadeu Lima de Souza Cascardo. 24) Fix crashes in 6lowpan, from Alexander Smirnov. 25) tcp_complete_cwr() needs to be careful to not rewind the CWND to ssthresh if ssthresh has the "infinite" value. Fix from Yuchung Cheng. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (81 commits) sungem: Fix WakeOnLan tcp: change tcp_adv_win_scale and tcp_rmem[2] net: l2tp: unlock socket lock before returning from l2tp_ip_sendmsg drop_monitor: prevent init path from scheduling on the wrong cpu usbnet: fix failure handling in usbnet_probe usbnet: fix leak of transfer buffer of dev->interrupt ucc_geth: Add 16 bytes to max TX frame for VLANs net: ucc_geth, increase no. of HW RX descriptors netem: fix possible skb leak sky2: fix receive length error in mixed non-VLAN/VLAN traffic sky2: propogate rx hash when packet is copied net: fix two typos in skbuff.h cxgb3: Don't call cxgb_vlan_mode until q locks are initialized ixgbe: fix calling skb_put on nonlinear skb assertion bug ixgbe: Fix a memory leak in IEEE DCB igbvf: fix the bug when initializing the igbvf smsc75xx: enable mac to detect speed/duplex from phy smsc75xx: declare smsc75xx's MII as GMII capable smsc75xx: fix phy interrupt acknowledge smsc75xx: fix phy init reset loop ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging由 Linus Torvalds 提交于
Pull hwmon fixes from Guenter Roeck: "Fix OOPS seen in coretemp driver if the CPU core ID is too large" * tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: hwmon: (coretemp) Increase CPU core limit hwmon: (coretemp) fix oops on cpu unplug
-
由 Viresh Kumar 提交于
SPEAr13xx series of SoCs contain Synopsys AHCI SATA Controller which shares ahci_platform driver with other controller versions. This patch updates DT compatible list for ahci_platform. It also updates and renames binding documentation to more generic name. Signed-off-by: NViresh Kumar <viresh.kumar@st.com> Cc: Rob Herring <rob.herring@calxeda.com> Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
-
由 Viresh Kumar 提交于
#ifdef, #endif is not required in definition/usage of arasan_cf_pm_ops. So, move this definition and its usage outside of them. Signed-off-by: NViresh Kumar <viresh.kumar@st.com> Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
-
由 Tero Roponen 提交于
When comparing the dmesg between 3.4-rc3 and 3.4-rc4 I found the following differences: -ata1: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff100 irq 47 -ata2: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff180 irq 47 -ata3: DUMMY +ata2: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff100 irq 47 +ata3: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff180 irq 47 ata4: DUMMY ata5: DUMMY -ata6: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff380 irq 47 +ata6: DUMMY +ata7: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff380 irq 47 The change of numbering comes from commit 85d6725b ("libata: make ata_print_id atomic") that changed lines like ap->print_id = ata_print_id++; to ap->print_id = atomic_inc_return(&ata_print_id); As the latter behaves like ++ata_print_id, we must initialize it to zero to start the numbering from one. Signed-off-by: NTero Roponen <tero.roponen@gmail.com> Acked-by: NDan Williams <dan.j.williams@intel.com> Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
-
由 Matt Johnson 提交于
The Marvell 88SE9172 SATA controller (PCI ID 1b4b 917a) already worked once it was detected, but was missing an ahci_pci_tbl entry. Boot tested on a Gigabyte Z68X-UD3H-B3 motherboard. Signed-off-by: NMatt Johnson <johnso87@illinois.edu> Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
-
由 Lin Ming 提交于
Commit d9027470("[libata] Add ATA transport class") introduced ATA_EFLAG_OLD_ER to mark entries in the error ring as cleared. But ata_count_probe_trials_cb() didn't check this flag and it still counts the old error history. So wrong probe trials count is returned and it causes problem, for example, SATA link speed is slowed down from 3.0Gbps to 1.5Gbps. Fix it by checking ATA_EFLAG_OLD_ER in ata_count_probe_trials_cb(). Cc: stable <stable@vger.kernel.org> # 2.6.37+ Signed-off-by: NLin Ming <ming.m.lin@intel.com> Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
- 03 5月, 2012 17 次提交
-
-
由 John W. Linville 提交于
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
-
由 Eric Dumazet 提交于
By default, iwlwifi uses order-1 pages (8 KB) to store incoming frames, but doesnt say so in skb->truesize. This makes very possible to exhaust kernel memory since these skb evade normal socket memory accounting. As struct ieee80211_hdr is going to be pulled before calling IP stack, there is no need to use dev_alloc_skb() to reserve NET_SKB_PAD bytes. alloc_skb() is ok in this driver, allowing more tailroom. Pull beginning of frame in skb header, in the hope we can reuse order-1 pages in the driver immediately for small frames and reduce their truesize to the minimum (linear skbs) Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Cc: Wey-Yi Guy <wey-yi.w.guy@intel.com> Cc: "John W. Linville" <linville@tuxdriver.com> Cc: Neal Cardwell <ncardwell@google.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 John Fastabend 提交于
After this commit: commit aacc1bea Author: Multanen, Eric W <eric.w.multanen@intel.com> Date: Wed Mar 28 07:49:09 2012 +0000 ixgbe: driver fix for link flap The BIT_APP_UPCHG bit is no longer set when ixgbe_dcbnl_set_all() is called. This results in the FCoE app user priority never getting set and the driver will not configure the tx_rings correctly for FCoE packets which use the SAN MTU and FCoE offloads. We resolve this regression by fixing ixgbe_copy_dcb_cfg() to also check for FCoE application changes. Additionally, we can drop the IEEE variants of get_dcb_app() because this path is never called with the IEEE mode enabled. Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com> Tested-by: NRoss Brattain <ross.b.brattain@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Don Skidmore 提交于
It was possible for shutdown to pull the rug out from other driver entry points. Now we just grab the rtnl lock before taking everything apart. Thanks to Hariharan for noticing this tight race condition. Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com> Cc: Hariharan Nagarajan <hanagara@cisco.com> Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Dave Airlie 提交于
We should initialise this to 0 really to avoid getting false positives. Cc: stable@vger.kernel.org Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Gerard Lledo 提交于
WakeOnLan was broken in this driver because gp->asleep_wol is a 1-bit bitfield and it was being assigned WAKE_MAGIC, which is (1 << 5). gp->asleep_wol remains 0 and the machine never wakes up. Fixed by casting gp->wake_on_lan to bool. Tested on an iBook G4. Signed-off-by: NGerard Lledo <gerard.lledo@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
tcp_adv_win_scale default value is 2, meaning we expect a good citizen skb to have skb->len / skb->truesize ratio of 75% (3/4) In 2.6 kernels we (mis)accounted for typical MSS=1460 frame : 1536 + 64 + 256 = 1856 'estimated truesize', and 1856 * 3/4 = 1392. So these skbs were considered as not bloated. With recent truesize fixes, a typical MSS=1460 frame truesize is now the more precise : 2048 + 256 = 2304. But 2304 * 3/4 = 1728. So these skb are not good citizen anymore, because 1460 < 1728 (GRO can escape this problem because it build skbs with a too low truesize.) This also means tcp advertises a too optimistic window for a given allocated rcvspace : When receiving frames, sk_rmem_alloc can hit sk_rcvbuf limit and we call tcp_prune_queue()/tcp_collapse() too often, especially when application is slow to drain its receive queue or in case of losses (netperf is fast, scp is slow). This is a major latency source. We should adjust the len/truesize ratio to 50% instead of 75% This patch : 1) changes tcp_adv_win_scale default to 1 instead of 2 2) increase tcp_rmem[2] limit from 4MB to 6MB to take into account better truesize tracking and to allow autotuning tcp receive window to reach same value than before. Note that same amount of kernel memory is consumed compared to 2.6 kernels. Signed-off-by: NEric Dumazet <edumazet@google.com> Cc: Neal Cardwell <ncardwell@google.com> Cc: Tom Herbert <therbert@google.com> Cc: Yuchung Cheng <ycheng@google.com> Acked-by: NNeal Cardwell <ncardwell@google.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Sasha Levin 提交于
l2tp_ip_sendmsg could return without releasing socket lock, making it all the way to userspace, and generating the following warning: [ 130.891594] ================================================ [ 130.894569] [ BUG: lock held when returning to user space! ] [ 130.897257] 3.4.0-rc5-next-20120501-sasha #104 Tainted: G W [ 130.900336] ------------------------------------------------ [ 130.902996] trinity/8384 is leaving the kernel with locks still held! [ 130.906106] 1 lock held by trinity/8384: [ 130.907924] #0: (sk_lock-AF_INET){+.+.+.}, at: [<ffffffff82b9503f>] l2tp_ip_sendmsg+0x2f/0x550 Introduced by commit 2f16270f ("l2tp: Fix locking in l2tp_ip.c"). Signed-off-by: NSasha Levin <levinsasha928@gmail.com> Acked-by: NEric Dumazet <edumazet@google.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Neil Horman 提交于
I just noticed after some recent updates, that the init path for the drop monitor protocol has a minor error. drop monitor maintains a per cpu structure, that gets initalized from a single cpu. Normally this is fine, as the protocol isn't in use yet, but I recently made a change that causes a failed skb allocation to reschedule itself . Given the current code, the implication is that this workqueue reschedule will take place on the wrong cpu. If drop monitor is used early during the boot process, its possible that two cpus will access a single per-cpu structure in parallel, possibly leading to data corruption. This patch fixes the situation, by storing the cpu number that a given instance of this per-cpu data should be accessed from. In the case of a need for a reschedule, the cpu stored in the struct is assigned the rescheule, rather than the currently executing cpu Tested successfully by myself. Signed-off-by: NNeil Horman <nhorman@tuxdriver.com> CC: David Miller <davem@davemloft.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 tom.leiming@gmail.com 提交于
If register_netdev returns failure, the dev->interrupt and its transfer buffer should be released, so just fix it. Signed-off-by: NMing Lei <tom.leiming@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 tom.leiming@gmail.com 提交于
The transfer buffer of dev->interrupt is allocated in .probe path, but not freed in .disconnet path, so mark the interrupt URB as URB_FREE_BUFFER to free the buffer when the URB is destroyed. Signed-off-by: NMing Lei <tom.leiming@gmail.com> Acked-by: NOliver Neukum <oneukum@suse.de> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Joakim Tjernlund 提交于
Creating a VLAN interface on top of ucc_geth adds 4 bytes to the frame and the HW controller is not prepared to TX a frame bigger than 1518 bytes which is 4 bytes too small for a full VLAN frame. Add 16 bytes which will handle the a simple VLAN and leaves 12 bytes for future expansion. Signed-off-by: NJoakim Tjernlund <Joakim.Tjernlund@transmode.se> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Joakim Tjernlund 提交于
In a busy network we see ucc_geth is dropping RX pkgs every now and then. Increase the RX queues HW descriptors from 16 to 32 to deal with this. Signed-off-by: NJoakim Tjernlund <Joakim.Tjernlund@transmode.se> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb由 Linus Torvalds 提交于
Pull USB patches from Greg Kroah-Hartman: "Here are two EHCI Tegra driver patches for your tree. The first is a bit big, but the majority is just moving code around. It is needed due to the other EHCI core changes that went in way back in 3.4-rc1, so this driver will now properly handle suspend/resume, as it was broken. The other one is a minor bugfix that resolves an warning that people have been seeing." * tag 'usb-3.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: USB: ehci-tegra: remove redundant gpio_set_value EHCI: update PM methods in ehci-tegra.c
-
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty由 Linus Torvalds 提交于
Pull a TTY fix from Greg Kroah-Hartman: "This is a deadlock bugfix that was easy to hit, and that the vt layer lock rework got wrong, so it reverts the logic back to the way it was in 3.3 and earlier kernels to prevent problems." * tag 'tty-3.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: vt: Fix deadlock on scroll-lock
-
由 Rajkumar Manoharan 提交于
This reverts commit a844adfd. The commit a844adfd is degrading rx sensitivity of lower rate in HT40 mode and it is confirmed that reverting the change is improving rx sensitivity. spur_freq_sd (for self-corr in AGC) is defined with respect to the center of each 20MHz channel while spur_phase_delta (for self-corr in Rx and spur data filter) is defined with respect to the center of current RF channel. So in short, we need to subtract spur_freq_sd (for self-corr in AGC) by the offset between the center of primary20 and the center of RF channel in SW. This offset could be +/10 MHz for dynamic 40. Cc: Madhan Jaganathan <madhanj@qca.qualcomm.com> Signed-off-by: NKai Shi <kaishi@qca.qualcomm.com> Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Franky Lin 提交于
dpc_tl_lock is not acquired in the error handle code for bus down. But it's unlocked using spin_unlock_irqrestore after finishing task list walk down. Grab the lock before breaking the loop to avoid a double unlock. Reported-by: NDan Carpenter <dan.carpenter@oracle.com> Signed-off-by: NFranky Lin <frankyl@broadcom.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 02 5月, 2012 2 次提交
-
-
git://git.linux-nfs.org/projects/trondmy/linux-nfs由 Linus Torvalds 提交于
Pull NFS client bugfixes from Trond Myklebust: - Fixes for the NFSv4 security negotiation - Use the correct hostname when mounting from a private namespace - NFS net namespace bugfixes for the pipefs filesystem - NFSv4 GETACL bugfixes - IPv6 bugfix for NFSv4 referrals * tag 'nfs-for-3.4-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: NFSv4.1: Use the correct hostname in the client identifier string SUNRPC: RPC client must use the current utsname hostname string NFS: get module in idmap PipeFS notifier callback NFS: Remove unused function nfs_lookup_with_sec() NFS: Honor the authflavor set in the clone mount data NFS: Fix following referral mount points with different security NFS: Do secinfo as part of lookup NFS: Handle exceptions coming out of nfs4_proc_fs_locations() NFS: Fix SECINFO_NO_NAME SUNRPC: traverse clients tree on PipeFS event SUNRPC: set per-net PipeFS superblock before notification SUNRPC: skip clients with program without PipeFS entries SUNRPC: skip dead but not buried clients on PipeFS events Avoid beyond bounds copy while caching ACL Avoid reading past buffer when calling GETACL fix page number calculation bug for block layout decode buffer NFSv4.1 fix page number calculation bug for filelayout decode buffers pnfs-obj: Remove unused variable from objlayout_get_deviceinfo() nfs4: fix referrals on mounts that use IPv6 addrs
-
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest由 Linus Torvalds 提交于
Pull two bug fixes in ktest from Steven Rostedt. * tag 'ktest-for-v3.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest: ktest: Fix reboot on success stopping all reboots ktest.pl: Fix combined usage of BISECT_REVERSE and BISECT_SKIP
-