The original driver had a restriction that if a card as an saa7113 chip,
then it cannot have a CI interface. This is not the case.
Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

These cards do not need the tda10021 configuration change when data is
streamed through a CAM module. This disables it for these ones.
Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This patch adds support for Satelco EasyWatch DVB-S light card,
a clone of the KNC 1, with PCI subsystem ID 1894:001e 
Signed-off-by: NLothar Englisch <Lothar.Englisch@lycos.de>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (4028): Change dvb_frontend_ops to be a real field instead of a pointer field inside dvb_frontend

The dvb_frontend_ops is a pointer inside dvb_frontend. That's why every demod-driver
is having a field of dvb_frontend_ops in its private-state-struct and
using the reference for filling the pointer-field in dvb_frontend.
- It saves at least two lines of code per demod-driver,
- reduces object size (one less dereference per frontend_ops-access),
- be coherent with dvb_tuner_ops,
- makes it a little bit easier for newbies to understand how it works and
- avoids stupid mistakes because you would have to copy the dvb_frontend_ops
  always, before you could assign the static pointer directly, which was
  dangerous.
Signed-off-by: NPatrick Boettcher <pb@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

These cards need special handling for CI - reinitialising the frontend
device when the CI module is reset. Additionally the tda10021 needs to be set
into a different transport stream mode when a CI module is present.
Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Don't try and set the tuner ops if the demod was not detected.
Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Rename pll calls to appropriate tuner calls.
Remove pll functions from demod structures.
Hook tuner call into tuner_ops.
Add pll gate control calls where appropriate.
Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Since I reordered the CI/frontend detection, it turns out the frontend needs
to have a GPIO set to power it on; otherwise frontend init fails.
Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Now that the CI code reinitialises the frontend, need to move the CI
initialisation to after the frontend init in order to ensure the frontend is
always in a good state. Fixes an oops caused by the frontend being NULL as
well.
Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Unfortunately on the budget-av board, the CAM reset line is tied to the
frontend reset line, so resetting the CAM also zaps the frontend. This
breaks the tda1004x at least, and causes it to fail to tune until the
budget-av module is reloaded. This patch adds an exported function to dvb_frontend
that allows a card to forcibly reinitialise a frontend. The budget-av now
does this on CAM reset, which corrects this problem.
since they do not tie the CAM reset line to the frontend reset line.
Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Support for Satelco EasyWatch DVB-S light.
Signed-off-by: NThilo Berger <thilo_berger@gmx.net>
Signed-off-by: NOliver Endriss <o.endriss@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- Added knc1 tv star dvb-s support with philips tuner sd1878.
Signed-off-by: NRegis Prevot <regis.prevot@anevia.com>
Signed-off-by: NMichael Krufky <mkrufky@m1k.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (3344a): Conversions from kmalloc+memset to k(z|c)alloc


Conversions from kmalloc+memset to k(z|c)alloc.
Signed-off-by: NPanagiotis Issaris <takis@issaris.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- minor whitespace cleanups
Signed-off-by: NMichael Krufky <mkrufky@m1k.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@brturbo.com.br>

- Port code for SU1278/SH2 (TUA6100) from pre-refactored code
Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@brturbo.com.br>

- Fixes for the topuptv/SCM mediaguard CAM module in KNC1 CI module
Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@brturbo.com.br>

Fixed DiSEqC timing for saa7146-based budget cards (speed-up ioctls using
SAA7146_I2C_SHORT_DELAY)
Signed-off-by: NOliver Endriss <o.endriss@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

stv0299_set_frontend(): reduced number of i2c transfers, set register 0x12
from inittab
Signed-off-by: NOliver Endriss <o.endriss@gmx.de>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Remove broken stv0299 enhanced tuning code
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Enable frontend on KNC plus cards.
Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: NJohannes Stezenbach <js@linuxtv.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fixes for CI interface.
Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: NJohannes Stezenbach <js@linuxtv.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Pass a pointer to the i2c bus to the pll callbacks (stv0299 only).

It was not possible to tell which i2c bus should be used if an adapter has
multiple frontends on multiple i2c buses.
Signed-off-by: NAndreas Oberritter <obi@linuxtv.org>
Signed-off-by: NJohannes Stezenbach <js@linuxtv.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The / in the driver name (budget dvb /w video in) is not a valid character for
device names - removed it, now it works!

Same for ttusb-budget.
Signed-off-by: NPatrick Boettcher <pb@linuxtv.org>
Signed-off-by: NJulian Scheel <julian@jusst.de>
Signed-off-by: NJohannes Stezenbach <js@linuxtv.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fix for QAM128 in VHF band suggested by Timo Helki.
Signed-off-by: NJohannes Stezenbach <js@linuxtv.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

o added config options for IF frequency and AGC
o support DSP boot from on board eeprom
o added pll sleep call
Signed-off-by: NHartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: NJohannes Stezenbach <js@linuxtv.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

- remove enable_ci, ci interface is assumed to be present if the saa7113
  is not found.
- reduce the delay when checking for saa7113
- clean up the cam reset according to specifications
- turn off Vcc to the cam slot if cam is removed or fails reset
- remove cam reset in ciintf_init
- clean up printks (KERN_)
- move gpio setting into saa7113_init
- clean up unreadable frontend_init
(Kenneth Aafloy)
Signed-off-by: NJohannes Stezenbach <js@linuxtv.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Modified dvb_register_adapter() to avoid kmalloc/kfree.  Drivers have to embed
struct dvb_adapter into their private data struct from now on.  (Andreas
Oberritter)
Signed-off-by: NJohannes Stezenbach <js@linuxtv.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Support KNC-1 Plus DVB-T and similar KNC-1 cards (Alexander Riedel)
Signed-off-by: NJohannes Stezenbach <js@linuxtv.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!