The interrupt pending register is write 1 clear.  If there are more than
one external interrupts pending at the same time, acking the first
interrupt by reading pending register then OR the corresponding bit and
write back to pending register will also clear other interrupt pending
bits.  That will cause loss of interrupt.
Signed-off-by: NDa Yu <dayu@datangmobile.cn>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Randomise ELF_ET_DYN_BASE, which is used when loading position independent
executables.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

On 64bit there is a possibility our stack and mmap randomisation will put
the two close enough such that we can't expand our stack to match the ulimit
specified.

To avoid this, start the upper mmap address at 1GB + 128MB below the top of our
address space, so in the worst case we end up with the same ~128MB hole as in
32bit. This works because we randomise the stack over a 1GB range.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

get_random_int() returns the same value within a 1 jiffy interval. This means
that the mmap and stack regions will almost always end up the same distance
apart, making a relative offset based attack possible.

To fix this, shift the randomness we use for the mmap region by 1 bit.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Randomize the heap.

before:
tundro2:~ # sleep 1 & cat /proc/${!}/maps | grep heap
10017000-10118000 rw-p 10017000 00:00 0                                  [heap]
10017000-10118000 rw-p 10017000 00:00 0                                  [heap]
10017000-10118000 rw-p 10017000 00:00 0                                  [heap]
10017000-10118000 rw-p 10017000 00:00 0                                  [heap]
10017000-10118000 rw-p 10017000 00:00 0                                  [heap]

after
tundro2:~ # sleep 1 & cat /proc/${!}/maps | grep heap
19419000-1951a000 rw-p 19419000 00:00 0                                  [heap]
325ff000-32700000 rw-p 325ff000 00:00 0                                  [heap]
1a97c000-1aa7d000 rw-p 1a97c000 00:00 0                                  [heap]
1cc60000-1cd61000 rw-p 1cc60000 00:00 0                                  [heap]
1afa9000-1b0aa000 rw-p 1afa9000 00:00 0                                  [heap]
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Randomise the lower bits of the stack address. More randomisation is good for
security but the scatter can also help with SMT threads that share an L1. A
quick test case shows this working:

int main()
{
	int sp;
	printf("%x\n", (unsigned long)&sp & 4095);
}

before:
80
80
80
80
80

after:
610
490
300
6b0
d80
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

At the moment we randomise the stack by 8MB on 32bit and 64bit tasks. Since we
have a lot more address space to play with on 64bit, lets do what x86 does and
increase that randomisation to 1GB:

before:
# for i in seq `1 10` ; do sleep 1 & cat /proc/${!}/maps | grep stack; done
fffffebc000-fffffed1000 rw-p ffffffeb000 00:00 0       [stack]
ffffff5a000-ffffff6f000 rw-p ffffffeb000 00:00 0       [stack]
fffffdb2000-fffffdc7000 rw-p ffffffeb000 00:00 0       [stack]
fffffd3e000-fffffd53000 rw-p ffffffeb000 00:00 0       [stack]
fffffad9000-fffffaee000 rw-p ffffffeb000 00:00 0       [stack]

after:
# for i in seq `1 10` ; do sleep 1 & cat /proc/${!}/maps | grep stack; done
ffff5c27000-ffff5c3c000 rw-p ffffffeb000 00:00 0       [stack]
fffebe5e000-fffebe73000 rw-p ffffffeb000 00:00 0       [stack]
fffcb298000-fffcb2ad000 rw-p ffffffeb000 00:00 0       [stack]
fffc719d000-fffc71b2000 rw-p ffffffeb000 00:00 0       [stack]
fffe01af000-fffe01c4000 rw-p ffffffeb000 00:00 0       [stack]
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Randomise mmap start address - 8MB on 32bit and 1GB on 64bit tasks.
Until ppc32 uses the mmap.c functionality, this is ppc64 specific.

Before:

# ./test & cat /proc/${!}/maps|tail -2|head -1
f75fe000-f7fff000 rw-p f75fe000 00:00 0
f75fe000-f7fff000 rw-p f75fe000 00:00 0
f75fe000-f7fff000 rw-p f75fe000 00:00 0
f75fe000-f7fff000 rw-p f75fe000 00:00 0
f75fe000-f7fff000 rw-p f75fe000 00:00 0

After:
# ./test & cat /proc/${!}/maps|tail -2|head -1
f718b000-f7b8c000 rw-p f718b000 00:00 0
f7551000-f7f52000 rw-p f7551000 00:00 0
f6ee7000-f78e8000 rw-p f6ee7000 00:00 0
f74d4000-f7ed5000 rw-p f74d4000 00:00 0
f6e9d000-f789e000 rw-p f6e9d000 00:00 0

Similar for 64bit, but with 1GB of scatter:
# ./test & cat /proc/${!}/maps|tail -2|head -1
fffb97b5000-fffb97b6000 rw-p fffb97b5000 00:00 0
fffce9a3000-fffce9a4000 rw-p fffce9a3000 00:00 0
fffeaaf2000-fffeaaf3000 rw-p fffeaaf2000 00:00 0
fffd88ac000-fffd88ad000 rw-p fffd88ac000 00:00 0
fffbc62e000-fffbc62f000 rw-p fffbc62e000 00:00 0
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Rearrange mmap.c to better match the x86 version.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Move is_32bit_task into asm/thread_info.h, that allows us to test for
32/64bit tasks without an ugly CONFIG_PPC64 ifdef.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

On Wed, 18 Feb 2009 22:18:21 +0100
Giuliano Pochini <pochini@shiny.it> wrote:

Since 2.6.28, /sys/devices/system/cpu/cpu*/online don't exist anymore
on 32-bit PowerMacs due to change in the generic powerpc code.
Signed-off-by: NGiuliano Pochini <pochini@shiny.it>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The new firmware release exports further RTC calls. This
patch adds these calls to the QPACE platform setup file.
Signed-off-by: NBenjamin Krill <ben@codiert.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

When we introduced VSX, we changed the way FPRs are stored in the
thread_struct.  Unfortunately we missed the load/store float double
alignment handler code when updating how we access FPRs in the
thread_struct.

Below fixes this and merges the little/big endian case.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

lfiwzx is a new floating point load instruction in 2.06 that needs an
alignment handler for Linux.

Turns out to be the worlds easiest handler to add.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This patch reworks the hot_add_scn_to_nid and its supporting functions
to make them easier to understand.  There are no functional changes in
this patch and has been tested on machine with memory represented in the
device tree as memory nodes and in the ibm,dynamic-memory property.

My previous patch that introduced support for hotplug memory add on
systems whose memory was represented by the ibm,dynamic-memory property
of the device tree only left the code more unintelligible.  This
will hopefully makes things easier to understand.
Signed-off-by: NNathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

While testing partition migration with heavy CPU load using
shared processors, it was observed that sometimes the migration
would never complete and would appear to hang. Currently, the
migration code assumes that if H_SUCCESS is returned from the H_JOIN
then the migration is complete and the processor is waking up on
the target system. If there was an outstanding PROD to the processor
when the H_JOIN is called, however, it will return H_SUCCESS on the source
system, causing the migration to hang, or in some scenarios cause
the kernel to crash on the complete call waking the caller
of rtas_percpu_suspend_me. Fix this by calling H_JOIN multiple times
if necessary during the migration.
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

There are hardware limitations on the number of available MSIs,
which firmware expresses using a property named "ibm,pe-total-#msi".
This property tells us how many MSIs are available for devices below
the point in the PCI tree where we find the property.

For old firmwares which don't have the property, we assume there are
8 MSIs available per "partitionable endpoint" (PE). The PE can be
found using existing EEH code, which uses the methods described in
PAPR. For our purposes we want the parent of the node that's
identified using this method.

When a driver requests n MSIs for a device, we first establish where
the "ibm,pe-total-#msi" property above that device is, or we find the
PE if the property is not found. In both cases we call this node
the "pe_dn".

We then count all non-bridge devices below the pe_dn, to establish
how many devices in total may need MSIs. The quota is then simply the
total available divided by the number of devices, if the request is
less than or equal to the quota, the request is fine and we're done.

If the request is greater than the quota, we try to determine if there
are any "spare" MSIs which we can give to this device. Spare MSIs are
found by looking for other devices which can never use their full
quota, because their "req#msi(-x)" property is less than the quota.

If we find any spare, we divide the spares by the number of devices
that could request more than their quota. This ensures the spare
MSIs are spread evenly amongst all over-quota requestors.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

If a driver asks for more MSIs than the devices "req#msi(-x)" property,
we currently return -ENOSPC. This doesn't give the driver any chance to
make a new request with a number that might work.

So if "req#msi(-x)" is less than the request, return its value. To be
100% safe, make sure we return an error if req_msi == 0.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The e500mc supports the new msgsnd/doorbell mechanisms that were added in
the Power ISA 2.05 architecture.  We use the normal level doorbell for
doing SMP IPIs at this point.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

cbe_cpufreq has a partial dependency on cbe_cpufreq_pmi, which cannot
be easily expressed in Kconfig. This fixes it by introducing an
extra Kconfig symbol CBE_CPUFREQ_PMI_ENABLE. To make the dependency
clearer, turn PPC_PMI into an automatic symbol.
Reported-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The spufs context directory contents definitions are not changed after
initialisation, so we can declare them as const. We can do the same
with the spu coredump reader callbacks too.
Signed-off-by: NJeremy Kerr <jk@ozlabs.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Currently, we may setup the MFC for isolated mode initilaisation with
the purge still active. This means that DMAs required to perform the
init do not happen.

This change clears the purge status after doing the purge, so that
the isolated init can proceed.
Signed-off-by: NJeremy Kerr <jk@ozlabs.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Currently, spu_handle_mm_fault disregards the 'ret' variable and always
returns -EFAULT on error.

This change refactos spu_handle_mm_fault a little, to return the
ret variable as appropriate. This allows us to combine the error and
sucess paths.

Also, remove the #if-0-ed IS_VALID_EA() check, it has never been
used.
Signed-off-by: NJeremy Kerr <jk@ozlabs.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

At the moment we size the hashtable based on 4kB pages / 2, even on a
64kB kernel. This results in a hashtable that is much larger than it
needs to be.

Grab the real page size and size the hashtable based on that

Note: This only has effect on non hypervisor machines.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This patch rewrites consistent dma allocations support to use vmalloc
layer to allocate virtual memory space from vmalloc pool and get rid
of CONFIG_CONSISTENT_{START,SIZE}.

This greatly simplifies the code by effectively removing a custom
allocator we had for virtual space.
Signed-off-by: NIlya Yanok <yanok@emcraft.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

include/asm/bootx.h:12: include of <linux/types.h> is preferred over <asm/types.h>
include/asm/bootx.h:57: found __[us]{8,16,32,64} type without #include <linux/types.h>
include/asm/elf.h:5: include of <linux/types.h> is preferred over <asm/types.h>
include/asm/kvm.h:23: include of <linux/types.h> is preferred over <asm/types.h>
include/asm/kvm.h:26: found __[us]{8,16,32,64} type without #include <linux/types.h>
include/asm/ps3fb.h:33: found __[us]{8,16,32,64} type without #include <linux/types.h>
include/asm/spu_info.h:27: found __[us]{8,16,32,64} type without #include <linux/types.h>
include/asm/swab.h:11: include of <linux/types.h> is preferred over <asm/types.h>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Old OF variants used to create a 'dummy' parent node "multifunc-device"
for devices with more than one PCI function. Our code that matches OF
nodes to PCI devices dealt with that in one place but not in another,
this fixes it.

This has the practical effect of fixing interrupt routing of multifunction
PCI cards on some older PowerMac machines.
Signed-off-by: NTom Arbuckle <tom.d.arbuckle@gmail.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Create a new header that becomes a single location for defining PowerPC
opcodes used by code that is either generationg instructions
at runtime (fixups, debug, etc.), emulating instructions, or just
compiling instructions old assemblers don't know about.

We currently don't handle the floating point emulation or alignment decode
as both are better handled by the specific decode support they already
have.

Added support for the new dcbzl, dcbal, msgsnd, tlbilx, & wait instructions
since older assemblers don't know about them.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Impact: clean up, remove duplicate code

When ftrace was first ported to PowerPC, there existed a
create_function_call that would create the instruction to make a call
to a given address. Unfortunately, this call expected to write to
the address it was given, and since it used the address to calculate
the offset, it could not be faked.

ftrace needed a way to create the instruction without actually writing
that instruction to the text section. So ftrace had to implement its
own code.

Now we have create_branch in the code patching library, which does
exactly what ftrace needs. This patch replaces ftrace's implementation
with the library function.
Signed-off-by: NSteven Rostedt <srostedt@redhat.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The original port of ftrace to PowerPC kept a lot of the code used
by x86. Some of this code was to handle x86's 5 byte instruction.
This was handled by using character arrays to manipulate the
code.

PowerPC has a consistent 4 byte instruction. Using unsigned ints
makes the code more efficient as well as more readable.
By converting to use unsigned ints to represent instructions,
I was able to remove the side effects that were needed for
manipulating character strings.

  i.e. memcpy and memcmp
Signed-off-by: NSteven Rostedt <srostedt@redhat.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This patch gets function graph tracing working with dynamic function
tracer on PowerPC32.
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This patch ports the function graph tracer for PowerPC, but only
for static function tracing.
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Impact: clean up

Use a macro to save and restore the registers for PowerPC32,
since that code is duplicated.

This is similar to the work done by Cyrill Gorcunov for the
mcount code in x86_64.
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The TOCS used by modules are different than the one used by
the core kernel code. The function graph tracer must save and
restore the TOC whenever it traces a module call. But this
is an added overhead to burden the majority of core kernel
code being traced.

Benjamin Herrenschmidt suggested in testing the entry of
the call to tell if it is a core kernel function or a module.
He recommended using the REGION_ID() macro to perform this test.

This patch implements Benjamin's idea, and uses a different
return_to_handler routine dependent on if the entry is a core
kernel function or not. The module version saves the TOC, where as
the core kernel version does not.

Geoff Lavand tested on PS3.
Tested-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NSteven Rostedt <srostedt@redhat.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This is the port of the function graph tracer to PowerPC with
dynamic tracing.

Geoff Lavand tested on PS3.
Tested-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NSteven Rostedt <srostedt@redhat.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This is a port of the function graph tracer that was written by
Frederic Weisbecker for the x86.

This only works for PPC64 at the moment and only for static tracing.
PPC32 and dynamic function graph tracing support will come later.

The trace produces a visual calling of functions:

 # tracer: function_graph
 #
 # CPU  DURATION                  FUNCTION CALLS
 # |     |   |                     |   |   |   |
  0)   2.224 us    |                        }
  0) ! 271.024 us  |                      }
  0) ! 320.080 us  |                    }
  0) ! 324.656 us  |                  }
  0) ! 329.136 us  |                }
  0)               |                .put_prev_task_fair() {
  0)               |                  .update_curr() {
  0)   2.240 us    |                    .update_min_vruntime();
  0)   6.512 us    |                  }
  0)   2.528 us    |                  .__enqueue_entity();
  0) + 15.536 us   |                }
  0)               |                .pick_next_task_fair() {
  0)   2.032 us    |                  .__pick_next_entity();
  0)   2.064 us    |                  .__clear_buddies();
  0)               |                  .set_next_entity() {
  0)   2.672 us    |                    .__dequeue_entity();
  0)   6.864 us    |                  }

Geoff Lavand tested on PS3.
Tested-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NSteven Rostedt <srostedt@redhat.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Michael Neuling reported a compile bug when dynamic ftrace was
configured in and modules were not. This was due to the ftrace
code referencing module specific structures.
Reported-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NSteven Rostedt <srostedt@redhat.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Impact: cleanup

The PowerPC ftrace code uses a hacked up DEBUGP macro for prints.
This patch converts it to the standard pr_debug.
Signed-off-by: NSteven Rostedt <srostedt@redhat.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

There is nothing really arch specific of the push and pop functions
used by the function graph tracer. This patch moves them to generic
code.
Acked-by: NFrederic Weisbecker <fweisbec@gmail.com>
Acked-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NSteven Rostedt <srostedt@redhat.com>

Impact: use new API, fix SMP bug.

Use the new accessors rather than frobbing bits directly.

This also removes the bug introduced in ee0c468b (alpha: compile
fixes) which had Alpha setting bits on an on-stack cpumask, not the
cpu_online_map.

Cc: Richard Henderson <rth@twiddle.net>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NMike Travis <travis@sgi.com>
Acked-by: NIvan Kokshaysky <ink@jurassic.park.msu.ru>
Acked-by: NIngo Molnar <mingo@elte.hu>