The temperature reporting interface stays the same, so we just
add the PCI-ID to the list.

Verified on AMD Olive Hill.
Signed-off-by: NWei Hu <wei@aristanetworks.com>
Acked-by: NClemens Ladisch <clemens@ladisch.de>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

This patch adds support for ads1115 device to ads1015 driver.
Based on work of Emiliano Carnati <carnatiatebneuro.com>.
Tested on ARM CPU based board.
Signed-off-by: NEvgeniy A. Dushistov <dushistov@mail.ru>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

GMT G762/763 fan speed PWM controller is connected directly to a fan
and performs closed-loop or open-loop control of the fan speed. Two
modes - PWM or DC - are supported by the chip. Introduced driver
provides various knobs to control the operations of the chip (via
sysfs interface). Specific characteristics of the system can be passed
either using board init code or via DT. Documentation for both the
driver and DT bindings are also provided.
Signed-off-by: NArnaud Ebalard <arno@natisbad.org>
Tested-by: NSimon Guinot <simon.guinot@sequanux.org>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

These changes add DS1731 chip support to the ds1621 driver,
Kconfig, and documentation.
Signed-off-by: NRobert Coulson <rob.coulson@gmail.com>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

Add definitions, information, and code for ds1631 chip support
to the ds1621 driver.
Signed-off-by: NRobert Coulson <rob.coulson@gmail.com>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

Update the ds1621 documentation, driver, and Kconfig with
ds1721 chip support.
Signed-off-by: NRobert Coulson <rob.coulson@gmail.com>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

Basically it's the same as the original DS75 but much faster.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NGuenter Roeck <linux@roeck-us.net>

TMP432 is similar to TMP431 with a second external temperature sensor.
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Acked-by: NJean Delvare <khali@linux-fr.org>

Each of ST-Ericsson X500 chip set series consists of both ABX500 and DBX500
chips. This is ABX500 hwmon driver, where the abx500.c is a common layer for
all ABX500s, and the ab8500.c is specific for AB8500 chip. Under this designed
structure, other chip specific files can be added simply using the same common
layer abx500.c.
Signed-off-by: NHongbo Zhang <hongbo.zhang@linaro.org>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Acked-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NAnton Vorontsov <anton@enomsg.org>

NCT6775, NCT6776, and NCT6779 have a number of variants with the same
chip ID but different chip labels. Add text "or compatible" to the
message displayed when the driver is loaded and rephrase the Kconfig
entry to reflect that it also supports compatible chips.
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

TMP431 is compatible to TMP401.

Also add support for additional I2C addresses supported by TMP411B
and TMP411C.
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Acked-by: NJean Delvare <khali@linux-fr.org>

This driver will replace the w83627ehf driver for NCT6775F and NCT6776F,
and provides support for NCT6779D.

This patch provides support for voltage monitor attributes.
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

This patch adds DT support to NTC driver to parse the
platform data.

Also adds the support to work as an iio device client.

During the probe ntc driver gets the respective channels of ADC
and uses iio_raw_read calls to get the ADC converted value.
Signed-off-by: NNaveen Krishna Chatradhi <ch.naveen@samsung.com>
[Guenter Roeck: fixed Kconfig dependencies; use ERR_CAST]
Tested-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

The adt7310/adt7320 is the SPI version of the adt7410/adt7420. The register map
layout is a bit different, i.e. the register addresses differ between the two
variants, but the bit layouts of the individual registers are identical. So both
chip variants can easily be supported by the same driver. The issue of non
matching register address layouts is solved by a simple look-up table which
translates the I2C addresses to the SPI addresses.

The patch moves the bulk of the adt7410 driver to a common module that will be
shared by the adt7410 and adt7310 drivers. This common module implements the
driver logic and uses a set of virtual functions to perform IO access. The
adt7410 and adt7310 driver modules provide proper implementations of these IO
accessor functions for I2C respective SPI.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Reviewed-by: NHartmut Knaack <knaack.h@gmx.de>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

This driver uses channel maps, defined either through device tree
or platform data, to create a hwmon driver which acts as a client
for the underlying IIO device channels.  Thus a general purpose
IIO adc driver can be used to provide hardware monitoring using a subset
of its channels.
Signed-off-by: NJonathan Cameron <jic23@kernel.org>
Acked-by: NGuenter Roeck <linux@roeck-us.net>

--
 The only non move changes here concern the description and changes to the
 dependencies to IIO explicit and hwmon implicit.

 I'm proposing moving this into hwmon on the basis of placing drivers
 based on what they provide rather than what their underlying hardware
 is.

 drivers/hwmon/Kconfig           |   9 ++
 drivers/hwmon/Makefile          |   1 +
 drivers/hwmon/iio_hwmon.c       | 196 ++++++++++++++++++++++++++++++++++++++++
 drivers/staging/iio/Kconfig     |   8 --
 drivers/staging/iio/Makefile    |   2 -
 drivers/staging/iio/iio_hwmon.c | 196 ----------------------------------------
 6 files changed, 206 insertions(+), 206 deletions(-)

The adt7420 is software compatible to the adt7410.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Reviewed-by: NHartmut Knaack <knaack.h@gmx.de>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Reviewed-by: NJean Delvare <khali@linux-fr.org>

Add support for the TI / Burr-Brown INA209 voltage / current / power
monitor.

Cc: Paul Hays <haysp@magma.net>
Cc: Ira W. Snyder <iws@ovro.caltech.edu>
Tested-by: NIra W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

Assume that IT8771E and IT8772E are fully compatible with IT8728F.

IT8771E support contributed by Kelly Anderson.
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Reviewed-by: NJean Delvare <khali@linux-fr.org>

Add support for MAX6581, MAX6602, MAX6622, MAX6636, MAX6689, MAX6693,
MAX6694, MAX6697, MAX6698, and MAX6699 temperature sensors
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Reviewed-by: NJean Delvare <khali@linux-fr.org>

This is the HWMON patch for DA9055 PMIC and has got dependency on the
DA9055 MFD core.

This patch monitors the DA9055 PMIC's ADC channels vddout, junction temperature
and auxiliary channels.

This patch is functionally tested on Samsung SMDKV6410.
Signed-off-by: NDavid Dajun Chen <dchen@diasemi.com>
Signed-off-by: NAshish Jangam <ashish.jangam@kpitcummins.com>
[Guenter Roeck: Dropped __devinit, __devexit, __devexit_p]
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

So far, we use the NM10 Express Chipset PCI chip ID to detect TjMax for
Atom CPUs with model 0x1c. As it turns out, we can use the CPU stepping
(x86_mask) for the same purpose; stepping is 10 for all model 0x1c CPUs
with TjMax of 100 degrees C. This was verified by checking the output of
/proc/cpuinfo for the respective CPUs (D4xx, D5xx, N4xx, N5xx).

Other CPUs currently covered by the same code (Exx, Z6xx, Z2460) are not
supported by the NM10 Express Chipset. Most of those CPUs have TjMax of 90
degrees C, except for E6xxT models which have a TjMax of 110 degrees C.
E6xxT CPUs can however not be detected by software.

Calculate TjMax for Atom CPUs as follows. Note that the listed values are not
correct in some cases (230, 330). tjmax_table is used for those to override
the default values.

ID	Stepping	TjMax		Models
0x1c	10		100		D4xx, N4xx, D5xx, N5xx
0x1c	not 10		90		Z5xx, N2xx, 230, 330, others
0x26	-		90		Atom Tunnel Creek (Exx),
					Lincroft (Z6xx)
0x27	-		90		Atom Medfield (Z2460)
0x36	-		100		Atom Cedar Trail (N2xxx, D2xxx)

Also drop the module dependency on PCI.
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Acked-by: NJean Delvare <khali@linux-fr.org>

The ADS7830 device is almost the same as the ADS7828,
except that it does 8-bit sampling, instead of 12-bit.
This patch extends the ads7828 driver to support this chip.
Signed-off-by: NGuillaume Roguez <guillaume.roguez@savoirfairelinux.com>
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

hwmon framework driver for Versatile Express sensors, providing
information about board level voltage (only when regulator driver
is not configured), currents, temperature and power/energy usage.
Labels for the values can be defined as DT properties.
Signed-off-by: NPawel Moll <pawel.moll@arm.com>
Acked-by: NGuenter Roeck <linux@roeck-us.net>

This movement is needed because the hwmon entries and corresponding sysfs
interface is a duplicate of utilities already provided by
driver/thermal/thermal_sys.c.  The goal is to place it in thermal folder
and add necessary functions to use the in-kernel thermal interfaces.
Signed-off-by: NAmit Daniel Kachhap <amit.kachhap@linaro.org>
Acked-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Cc: SangWook Ju <sw.ju@samsung.com>
Cc: Durgadoss <durgadoss.r@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NAmit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: NZhang Rui <rui.zhang@intel.com>

This Patch adds support for mcp3221 chip to the
mcp3021 driver.
Signed-off-by: NSven Schuchmann <schuchmann@schleissheimer.de>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

CONFIG_EXPERIMENTAL is expected to be removed, so drop dependencies on it.
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: NJean Delvare <khali@linux-fr.org>

Add missing reference to IT8782F and IT8783E/F to it87 driver description
in Kconfig. Replace wrong reference to Si960 with the correct Si950.
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Acked-by: NJean Delvare <khali@linux-fr.org>

INA220 is register compatible to INA219, and INA230 is register compatible to
INA226, so all we need to do is to add name aliases for those two chips.

Cc: Lothar Felten <l-felten@ti.com>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Reviewed-by: NJean Delvare <khali@linux-fr.org>

MAX1110 is similar to MAX1111, with 8 instead of 4 channels. MAX1112 and MAX1113
are similar to MAX1110 and MAX1111, with 4.096V reference voltage instead of
2.048V.
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Acked-by: NJean Delvare <khali@linux-fr.org>

Add support for LM74 and LM71 to LM70 driver.
Signed-off-by: NChristophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

The MAX197 is an A/D converter, made by Maxim. This driver currently
supports the MAX197, and MAX199. They are both 8-Channel, Multi-Range,
5V, 12-Bit DAS with 8+4 Bus Interface and Fault Protection.

The available ranges for the MAX197 are {0,-5V} to 5V, and {0,-10V} to
10V, while they are {0,-2V} to 2V, and {0,-4V} to 4V on the MAX199.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

This patch brings basic support for the Analog Devices ADT7410 temperature
sensor. The following functionality has been implemented:

  * get current temperature
  * get/set minimum, maximum and critical temperature
  * get/set hysteresis
  * get alarm events for minimum, maximum and critical temperature

All implemented sysfs attributes have been sucessfully tested at temperatures
of 15°C to 40°C.
Signed-off-by: NHartmut Knaack <knaack.h@gmx.de>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

This is a new driver for the Honeywell Humidicon HIH-6130/HIH-6131 humidity sensor.

The driver is based on the existing Sensiron sht21 driver with the necessary changes
to the probe, update_measurements and conversion functions necessary to use the
Honeywell sensors.

There's no difference between the 6130 & 6131 other than the 6131 having an external
condensation filter attached.
Signed-off-by: NIain Paton <ipaton0@gmail.com>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

The DA9052 PMIC provides an Analogue to Digital Converter with 10 bits
resolution and 10 channels.

This patch monitors the DA9052 PMIC's ADC channels mostly for battery
parameters like battery temperature, junction temperature, battery
current etc.

This patch is functionally tested on Samsung SMDKV6410
Signed-off-by: NDavid Dajun Chen <dchen@diasemi.com>
Signed-off-by: NAshish Jangam <ashish.jangam@kpitcummins.com>
[Guenter Roeck: __init --> __devinit for probe function]
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

Since the watchdog code in sch56xx-common now uses the watchdog core, the
Kconfig entires for the sch5627 and sch5636 should depend on WATCHDOG
being set. Also select the watchdog core when we select one of the drivers.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Add support for the Texas Instruments INA219 and INA226 power monitors.
Signed-off-by: NLothar Felten <l-felten@ti.com>
[guenter.roeck@ericsson.com: formatting cleanup; check for smbus word data;
 select PGA=8 for INA219]
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

Correct spelling typo in various Kconfig file.
Signed-off-by: NMasanari Iida <standby24x7@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The on-chip northbridge's temperature sensor of the upcoming
AMD Trinity CPUs works the same as for the previous CPUs.
Since it has a different PCI-ID, we just add the new one to the list
supported by k10temp.
This allows to use the k10temp driver on those CPUs.
Signed-off-by: NAndre Przywara <andre.przywara@amd.com>
Cc: stable@vger.kernel.org # 3.0+
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>