rocker_port_fdb_flush() is called by rocker_port_stp_update() which in
turn may be called with trans == SWITCHDEV_TRANS_PREPARE and then
trans == SWITCHDEV_TRANS_COMMIT from switchdev_port_attr_set() via
br_set_state().

When rocker_port_fdb_flush() is called with trans == SWITCHDEV_TRANS_PREPARE
it calls rocker_port_fdb_learn() for each entry in the FDB table which in
turn calls rocker_flow_tbl_bridge() which will allocate memory using
rocker_port_kzalloc(). rocker_port_fdb_learn() will then remove the entry
from the FDB table.

Then when rocker_port_fdb_learn() is called with
trans == SWITCHDEV_TRANS_PREPARE no calls are made to rocker_port_fdb_learn()
because there are no longer any entries present in the FDB table. Thus the
memory previously allocated by rocker_port_fdb_learn() is leaked resulting
in the kernel BUG() below.

Furthermore, it looks like the driver ends up with an incorrect view of the
fdb table as the FDB entries are purged from the driver's table but not the
hardware's table.

ip link add br0 type bridge
ip link set up dev eth0
sleep 1
ip link set dev eth0 master br0
[    3.704360] ------------[ cut here ]------------
[    3.704611] kernel BUG at drivers/net/ethernet/rocker/rocker.c:4289!
[    3.704962] invalid opcode: 0000 [#1] SMP
[    3.705537] Modules linked in:
[    3.705919] CPU: 0 PID: 63 Comm: ip Not tainted 4.1.0-rc3-01046-gb9fbe709 #1044
[    3.706191] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.8.0-0-g4c59f5d-20150219_092859-nilsson.home.kraxel.org 04/01/2014
[    3.706820] task: ffff880019f70150 ti: ffff88001f92c000 task.ti: ffff88001f92c000
[    3.707138] RIP: 0010:[<ffffffff811f0080>]  [<ffffffff811f0080>] rocker_port_attr_set+0xe0/0xf0
[    3.707990] RSP: 0018:ffff88001f92f808  EFLAGS: 00000212
[    3.708200] RAX: ffff880019d4fa68 RBX: ffff880019d4f000 RCX: 0000000000000000
[    3.708471] RDX: 000000000000000c RSI: ffff88001f92f890 RDI: ffff880019d4f680
[    3.708740] RBP: 0000000000000001 R08: 0000000000000000 R09: 0000000000000004
[    3.708999] R10: ffff880000034024 R11: 0000000000000000 R12: ffff88001f92f890
[    3.709276] R13: ffff88001f8f1c00 R14: 000000000000000b R15: 0000000000000000
[    3.709303] FS:  00007f8ab66bd700(0000) GS:ffff88001b000000(0000) knlGS:0000000000000000
[    3.709303] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[    3.709303] CR2: 0000000000654988 CR3: 000000001f8f3000 CR4: 00000000000006b0
[    3.709303] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[    3.709303] DR3: 0000000000000000 DR6: 0000000000000000 DR7: 0000000000000000
[    3.709303] Stack:
[    3.709303]  ffff88001f8f1c00 000000000000000b ffff88001f92f890 ffff880019d4f000
[    3.709303]  ffff88001f92f890 ffffffff813332f5 ffff88001f92f880 0000000000000000
[    3.709303]  ffff88001f92f890 0000000000000001 ffff880019d4f000 ffffffff81333627
[    3.709303] Call Trace:
[    3.709303]  [<ffffffff813332f5>] ? __switchdev_port_attr_set+0x25/0x90
[    3.709303]  [<ffffffff81333627>] ? switchdev_port_attr_set+0x27/0x120
[    3.709303]  [<ffffffff81318e86>] ? br_set_state+0x36/0x50
[    3.709303]  [<ffffffff8131795c>] ? br_add_if+0x37c/0x400
[    3.709303]  [<ffffffff81238ce1>] ? do_setlink+0x7e1/0x800
[    3.709303]  [<ffffffff8111f980>] ? radix_tree_lookup_slot+0x10/0x30
[    3.709303]  [<ffffffff81136fba>] ? nla_parse+0xaa/0x110
[    3.709303]  [<ffffffff81239c98>] ? rtnl_newlink+0x548/0x870
[    3.709303]  [<ffffffff8111f900>] ? __radix_tree_lookup+0x40/0xb0
[    3.709303]  [<ffffffff81136f3e>] ? nla_parse+0x2e/0x110
[    3.709303]  [<ffffffff81237d7e>] ? rtnetlink_rcv_msg+0x7e/0x250
[    3.709303]  [<ffffffff8121d1be>] ? __skb_recv_datagram+0xfe/0x4b0
[    3.709303]  [<ffffffff81237d00>] ? rtnetlink_rcv+0x30/0x30
[    3.709303]  [<ffffffff81247948>] ? netlink_rcv_skb+0xa8/0xd0
[    3.709303]  [<ffffffff81237cef>] ? rtnetlink_rcv+0x1f/0x30
[    3.709303]  [<ffffffff81247210>] ? netlink_unicast+0x150/0x200
[    3.709303]  [<ffffffff81247704>] ? netlink_sendmsg+0x374/0x3e0
[    3.709303]  [<ffffffff8120f8cf>] ? sock_sendmsg+0xf/0x30
[    3.709303]  [<ffffffff8120ffc3>] ? ___sys_sendmsg+0x1f3/0x200
[    3.709303]  [<ffffffff812100d5>] ? ___sys_recvmsg+0x105/0x140
[    3.709303]  [<ffffffff812228d9>] ? dev_get_by_name_rcu+0x69/0x90
[    3.709303]  [<ffffffff812228d9>] ? dev_get_by_name_rcu+0x69/0x90
[    3.709303]  [<ffffffff81217b7d>] ? skb_dequeue+0x4d/0x60
[    3.709303]  [<ffffffff81217bb0>] ? skb_queue_purge+0x20/0x30
[    3.709303]  [<ffffffff810ebdcf>] ? __inode_wait_for_writeback+0x5f/0xb0
[    3.709303]  [<ffffffff810648b0>] ? autoremove_wake_function+0x30/0x30
[    3.709303]  [<ffffffff81210ee9>] ? __sys_sendmsg+0x39/0x70
[    3.709303]  [<ffffffff8133e097>] ? system_call_fastpath+0x12/0x6a
[    3.709303] Code: bb 90 06 00 00 48 c7 04 24 00 00 00 00 45 31 c9 45 31 c0 48 c7 c1 c0 b7 1e 81 89 ea e8 da da ff ff eb 95 0f 1f 84 00 00 00 00 00 <0f> 0b 66 66 66 66 66 2e 0f 1f 84 00 00 00 00 00 48 83 fe 15 75
[    3.709303] RIP  [<ffffffff811f0080>] rocker_port_attr_set+0xe0/0xf0
[    3.709303]  RSP <ffff88001f92f808>
[    3.721409] ---[ end trace b7481fcb7cb032aa ]---
Segmentation fault

Fixes: c4f20321 ("rocker: support prepare-commit transaction model")
Acked-by: NScott Feldman <sfeldma@gmail.com>
Acked-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the generic mechanism to declare a bitmap instead of unsigned long.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Alexei Starovoitov says:

====================
bpf: introduce bpf_tail_call() helper

introduce bpf_tail_call(ctx, &jmp_table, index) helper function
which can be used from BPF programs like:
int bpf_prog(struct pt_regs *ctx)
{
  ...
  bpf_tail_call(ctx, &jmp_table, index);
  ...
}
that is roughly equivalent to:
int bpf_prog(struct pt_regs *ctx)
{
  ...
  if (jmp_table[index])
    return (*jmp_table[index])(ctx);
  ...
}
The important detail that it's not a normal call, but a tail call.
The kernel stack is precious, so this helper reuses the current
stack frame and jumps into another BPF program without adding
extra call frame.
It's trivially done in interpreter and a bit trickier in JITs.

Use cases:
- simplify complex programs
- dispatch into other programs
  (for example: index in jump table can be syscall number or network protocol)
- build dynamic chains of programs

The chain of tail calls can form unpredictable dynamic loops therefore
tail_call_cnt is used to limit the number of calls and currently is set to 32.

patch 1 - support bpf_tail_call() in interpreter
patch 2 - support in x64 JIT
We've discussed what's neccessary to support it in arm64/s390 JITs
and it looks fine.
patch 3 - sample example for tracing
patch 4 - sample example for networking

More details in every patch.

This set went through several iterations of reviews/fixes and older
attempts can be seen:
https://git.kernel.org/cgit/linux/kernel/git/ast/bpf.git/log/?h=tail_call_v[123456]
- tail_call_v1 does it without touching JITs but introduces overhead
  for all programs that don't use this helper function.
- tail_call_v2 still has some overhead and x64 JIT does full stack
  unwind (prologue skipping optimization wasn't there)
- tail_call_v3 reuses 'call' instruction encoding and has interpreter
  overhead for every normal call
- tail_call_v4 fixes above architectural shortcomings and v5,v6 fix few
  more bugs

This last tail_call_v6 approach seems to be the best.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Usage:
$ sudo ./sockex3
IP     src.port -> dst.port               bytes      packets
127.0.0.1.42010 -> 127.0.0.1.12865         1568            8
127.0.0.1.59526 -> 127.0.0.1.33778     11422636       173070
127.0.0.1.33778 -> 127.0.0.1.59526  11260224828       341974
127.0.0.1.12865 -> 127.0.0.1.42010         1832           12
IP     src.port -> dst.port               bytes      packets
127.0.0.1.42010 -> 127.0.0.1.12865         1568            8
127.0.0.1.59526 -> 127.0.0.1.33778     23198092       351486
127.0.0.1.33778 -> 127.0.0.1.59526  22972698518       698616
127.0.0.1.12865 -> 127.0.0.1.42010         1832           12

this example is similar to sockex2 in a way that it accumulates per-flow
statistics, but it does packet parsing differently.
sockex2 inlines full packet parser routine into single bpf program.
This sockex3 example have 4 independent programs that parse vlan, mpls, ip, ipv6
and one main program that starts the process.
bpf_tail_call() mechanism allows each program to be small and be called
on demand potentially multiple times, so that many vlan, mpls, ip in ip,
gre encapsulations can be parsed. These and other protocol parsers can
be added or removed at runtime. TLVs can be parsed in similar manner.
Note, tail_call_cnt dynamic check limits the number of tail calls to 32.
Signed-off-by: NAlexei Starovoitov <ast@plumgrid.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

kprobe example that demonstrates how future seccomp programs may look like.
It attaches to seccomp_phase1() function and tail-calls other BPF programs
depending on syscall number.

Existing optimized classic BPF seccomp programs generated by Chrome look like:
if (sd.nr < 121) {
  if (sd.nr < 57) {
    if (sd.nr < 22) {
      if (sd.nr < 7) {
        if (sd.nr < 4) {
          if (sd.nr < 1) {
            check sys_read
          } else {
            if (sd.nr < 3) {
              check sys_write and sys_open
            } else {
              check sys_close
            }
          }
        } else {
      } else {
    } else {
  } else {
} else {
}

the future seccomp using native eBPF may look like:
  bpf_tail_call(&sd, &syscall_jmp_table, sd.nr);
which is simpler, faster and leaves more room for per-syscall checks.

Usage:
$ sudo ./tracex5
<...>-366   [001] d...     4.870033: : read(fd=1, buf=00007f6d5bebf000, size=771)
<...>-369   [003] d...     4.870066: : mmap
<...>-369   [003] d...     4.870077: : syscall=110 (one of get/set uid/pid/gid)
<...>-369   [003] d...     4.870089: : syscall=107 (one of get/set uid/pid/gid)
   sh-369   [000] d...     4.891740: : read(fd=0, buf=00000000023d1000, size=512)
   sh-369   [000] d...     4.891747: : write(fd=1, buf=00000000023d3000, size=512)
   sh-369   [000] d...     4.891747: : read(fd=1, buf=00000000023d3000, size=512)
Signed-off-by: NAlexei Starovoitov <ast@plumgrid.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bpf_tail_call() arguments:
ctx - context pointer
jmp_table - one of BPF_MAP_TYPE_PROG_ARRAY maps used as the jump table
index - index in the jump table

In this implementation x64 JIT bypasses stack unwind and jumps into the
callee program after prologue, so the callee program reuses the same stack.

The logic can be roughly expressed in C like:

u32 tail_call_cnt;

void *jumptable[2] = { &&label1, &&label2 };

int bpf_prog1(void *ctx)
{
label1:
    ...
}

int bpf_prog2(void *ctx)
{
label2:
    ...
}

int bpf_prog1(void *ctx)
{
    ...
    if (tail_call_cnt++ < MAX_TAIL_CALL_CNT)
        goto *jumptable[index]; ... and pass my 'ctx' to callee ...

    ... fall through if no entry in jumptable ...
}

Note that 'skip current program epilogue and next program prologue' is
an optimization. Other JITs don't have to do it the same way.
>From safety point of view it's valid as well, since programs always
initialize the stack before use, so any residue in the stack left by
the current program is not going be read. The same verifier checks are
done for the calls from the kernel into all bpf programs.
Signed-off-by: NAlexei Starovoitov <ast@plumgrid.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

introduce bpf_tail_call(ctx, &jmp_table, index) helper function
which can be used from BPF programs like:
int bpf_prog(struct pt_regs *ctx)
{
  ...
  bpf_tail_call(ctx, &jmp_table, index);
  ...
}
that is roughly equivalent to:
int bpf_prog(struct pt_regs *ctx)
{
  ...
  if (jmp_table[index])
    return (*jmp_table[index])(ctx);
  ...
}
The important detail that it's not a normal call, but a tail call.
The kernel stack is precious, so this helper reuses the current
stack frame and jumps into another BPF program without adding
extra call frame.
It's trivially done in interpreter and a bit trickier in JITs.
In case of x64 JIT the bigger part of generated assembler prologue
is common for all programs, so it is simply skipped while jumping.
Other JITs can do similar prologue-skipping optimization or
do stack unwind before jumping into the next program.

bpf_tail_call() arguments:
ctx - context pointer
jmp_table - one of BPF_MAP_TYPE_PROG_ARRAY maps used as the jump table
index - index in the jump table

Since all BPF programs are idenitified by file descriptor, user space
need to populate the jmp_table with FDs of other BPF programs.
If jmp_table[index] is empty the bpf_tail_call() doesn't jump anywhere
and program execution continues as normal.

New BPF_MAP_TYPE_PROG_ARRAY map type is introduced so that user space can
populate this jmp_table array with FDs of other bpf programs.
Programs can share the same jmp_table array or use multiple jmp_tables.

The chain of tail calls can form unpredictable dynamic loops therefore
tail_call_cnt is used to limit the number of calls and currently is set to 32.

Use cases:
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>

==========
- simplify complex programs by splitting them into a sequence of small programs

- dispatch routine
  For tracing and future seccomp the program may be triggered on all system
  calls, but processing of syscall arguments will be different. It's more
  efficient to implement them as:
  int syscall_entry(struct seccomp_data *ctx)
  {
     bpf_tail_call(ctx, &syscall_jmp_table, ctx->nr /* syscall number */);
     ... default: process unknown syscall ...
  }
  int sys_write_event(struct seccomp_data *ctx) {...}
  int sys_read_event(struct seccomp_data *ctx) {...}
  syscall_jmp_table[__NR_write] = sys_write_event;
  syscall_jmp_table[__NR_read] = sys_read_event;

  For networking the program may call into different parsers depending on
  packet format, like:
  int packet_parser(struct __sk_buff *skb)
  {
     ... parse L2, L3 here ...
     __u8 ipproto = load_byte(skb, ... offsetof(struct iphdr, protocol));
     bpf_tail_call(skb, &ipproto_jmp_table, ipproto);
     ... default: process unknown protocol ...
  }
  int parse_tcp(struct __sk_buff *skb) {...}
  int parse_udp(struct __sk_buff *skb) {...}
  ipproto_jmp_table[IPPROTO_TCP] = parse_tcp;
  ipproto_jmp_table[IPPROTO_UDP] = parse_udp;

- for TC use case, bpf_tail_call() allows to implement reclassify-like logic

- bpf_map_update_elem/delete calls into BPF_MAP_TYPE_PROG_ARRAY jump table
  are atomic, so user space can build chains of BPF programs on the fly

Implementation details:
=======================
- high performance of bpf_tail_call() is the goal.
  It could have been implemented without JIT changes as a wrapper on top of
  BPF_PROG_RUN() macro, but with two downsides:
  . all programs would have to pay performance penalty for this feature and
    tail call itself would be slower, since mandatory stack unwind, return,
    stack allocate would be done for every tailcall.
  . tailcall would be limited to programs running preempt_disabled, since
    generic 'void *ctx' doesn't have room for 'tail_call_cnt' and it would
    need to be either global per_cpu variable accessed by helper and by wrapper
    or global variable protected by locks.

  In this implementation x64 JIT bypasses stack unwind and jumps into the
  callee program after prologue.

- bpf_prog_array_compatible() ensures that prog_type of callee and caller
  are the same and JITed/non-JITed flag is the same, since calling JITed
  program from non-JITed is invalid, since stack frames are different.
  Similarly calling kprobe type program from socket type program is invalid.

- jump table is implemented as BPF_MAP_TYPE_PROG_ARRAY to reuse 'map'
  abstraction, its user space API and all of verifier logic.
  It's in the existing arraymap.c file, since several functions are
  shared with regular array map.
Signed-off-by: NAlexei Starovoitov <ast@plumgrid.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reduce ifdef pollution slightly, no functional change. We can simply
remove the extra alternative definition of handle_ing() and nf_ingress().
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In commit 8e4d980a ("tcp: fix behavior for epoll edge trigger")
we fixed a possible hang of TCP sockets under memory pressure,
by allowing sk_stream_alloc_skb() to use sk_forced_mem_schedule()
if no packet is in socket write queue.

It turns out there are other cases where we want to force memory
schedule :

tcp_fragment() & tso_fragment() need to split a big TSO packet into
two smaller ones. If we block here because of TCP memory pressure,
we can effectively block TCP socket from sending new data.
If no further ACK is coming, this hang would be definitive, and socket
has no chance to effectively reduce its memory usage.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

[1] When entering NUD_PROBE state via neigh_update(), perhaps received
    from userspace, correctly (re)initialize the probes count to zero.

    This is useful for forcing revalidation of a neighbor (for example
    if the host is attempting to do DNA [IPv4 4436, IPv6 6059]).

[2] Notify listeners when a neighbor goes into NUD_PROBE state.

    By sending notifications on entry to NUD_PROBE state listeners get
    more timely warnings of imminent connectivity issues.

    The current notifications on entry to NUD_STALE have somewhat
    limited usefulness: NUD_STALE is a perfectly normal state, as is
    NUD_DELAY, whereas notifications on entry to NUD_FAILURE come after
    a neighbor reachability problem has been confirmed (typically after
    three probes).
Signed-off-by: NErik Kline <ek@google.com>
Acked-By: NLorenzo Colitti <lorenzo@google.com>
Acked-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ip_do_nat() function was removed prior to kernel 3.4. Remove the
unnecessary function prototype as well.
Reported-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NAndy Zhou <azhou@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This work as a follow-up of commit f7b3bec6 ("net: allow setting ecn
via routing table") and adds RFC3168 section 6.1.1.1. fallback for outgoing
ECN connections. In other words, this work adds a retry with a non-ECN
setup SYN packet, as suggested from the RFC on the first timeout:

  [...] A host that receives no reply to an ECN-setup SYN within the
  normal SYN retransmission timeout interval MAY resend the SYN and
  any subsequent SYN retransmissions with CWR and ECE cleared. [...]

Schematic client-side view when assuming the server is in tcp_ecn=2 mode,
that is, Linux default since 2009 via commit 255cac91 ("tcp: extend
ECN sysctl to allow server-side only ECN"):

 1) Normal ECN-capable path:

    SYN ECE CWR ----->
                <----- SYN ACK ECE
            ACK ----->

 2) Path with broken middlebox, when client has fallback:

    SYN ECE CWR ----X crappy middlebox drops packet
                      (timeout, rtx)
            SYN ----->
                <----- SYN ACK
            ACK ----->

In case we would not have the fallback implemented, the middlebox drop
point would basically end up as:

    SYN ECE CWR ----X crappy middlebox drops packet
                      (timeout, rtx)
    SYN ECE CWR ----X crappy middlebox drops packet
                      (timeout, rtx)
    SYN ECE CWR ----X crappy middlebox drops packet
                      (timeout, rtx)

In any case, it's rather a smaller percentage of sites where there would
occur such additional setup latency: it was found in end of 2014 that ~56%
of IPv4 and 65% of IPv6 servers of Alexa 1 million list would negotiate
ECN (aka tcp_ecn=2 default), 0.42% of these webservers will fail to connect
when trying to negotiate with ECN (tcp_ecn=1) due to timeouts, which the
fallback would mitigate with a slight latency trade-off. Recent related
paper on this topic:

  Brian Trammell, Mirja Kühlewind, Damiano Boppart, Iain Learmonth,
  Gorry Fairhurst, and Richard Scheffenegger:
    "Enabling Internet-Wide Deployment of Explicit Congestion Notification."
    Proc. PAM 2015, New York.
  http://ecn.ethz.ch/ecn-pam15.pdf

Thus, when net.ipv4.tcp_ecn=1 is being set, the patch will perform RFC3168,
section 6.1.1.1. fallback on timeout. For users explicitly not wanting this
which can be in DC use case, we add a net.ipv4.tcp_ecn_fallback knob that
allows for disabling the fallback.

tp->ecn_flags are not being cleared in tcp_ecn_clear_syn() on output, but
rather we let tcp_ecn_rcv_synack() take that over on input path in case a
SYN ACK ECE was delayed. Thus a spurious SYN retransmission will not prevent
ECN being negotiated eventually in that case.

Reference: https://www.ietf.org/proceedings/92/slides/slides-92-iccrg-1.pdf
Reference: https://www.ietf.org/proceedings/89/slides/slides-89-tsvarea-1.pdfSigned-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NMirja Kühlewind <mirja.kuehlewind@tik.ee.ethz.ch>
Signed-off-by: NBrian Trammell <trammell@tik.ee.ethz.ch>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Dave That <dave.taht@gmail.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hariprasad Shenai says:

====================
cxgb4: Remove dead code and replace byte-oder functions

This series removes dead fn t4_read_edc and t4_read_mc, also replaces
ntoh{s,l} and hton{s,l} calls with the generic byteorder.

PATCH 2/2 was sent as a single PATCH, but had some byte-ordering issues
in t4_read_edc and t4_read_mc function. Found that t4_read_edc and
t4_read_mc is unused, so PATCH 1/2 is added to remove it.

This patch series is created against net-next tree and includes
patches on cxgb4 driver.

We have included all the maintainers of respective drivers. Kindly review
the change and let us know in case of any review comments.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

replace ntoh{s,l} and hton{s,l} calls with the generic byteorder in
cxgb4/t4_hw.c file
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge tag 'mac80211-next-for-davem-2015-05-19' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next

Johannes Berg says:

====================
This just has a few fixes:
 * LED throughput trigger was crashing
 * fast-xmit wasn't treating QoS changes in IBSS correctly
 * TDLS could use the wrong channel definition
 * using a reserved channel context could use the wrong channel width
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The hwmon interface in the be2net driver causes a link error when
be2net is built-in while the hwmon subsystem is a loadable module:

drivers/built-in.o: In function `be_probe':
drivers/net/ethernet/emulex/benet/be_main.c:5761: undefined reference to `devm_hwmon_device_register_with_groups'

This adds a new Kconfig symbol, following the example of multiple
other drivers that have the same problem. The new CONFIG_BE2NET_HWMON
will not be available when (BE2NET=y && HWMON=m) to avoid this
problem.

We have to also mark be_hwmon_show_temp as 'static' to ensure the
compiler can optimize out all the unused code.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Fixes: 29e9122b ("be2net: Export board temperature using hwmon-sysfs interface.")
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the getsockopt() requesting the cached contents of the syn
packet headers will fail silently if the caller uses a buffer that is
too small to contain the requested data.  Rather than fail silently and
discard the headers, getsockopt() should return an error and report the
required size to hold the data.
Signed-off-by: NEric B Munson <emunson@akamai.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NParav Pandit <parav.pandit@avagotech.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Andy Zhou says:

====================
fragmentation ICMP

Currently, we send ICMP packets when errors occur during fragmentation or
de-fragmentation.  However, it is a bug when sending those ICMP packets
in the context of using netfilter for bridging.

Those ICMP packets are only expected in the context of routing, not in
bridging mode.

The local stack is not involved in bridging forward decisions, thus
should be not used for deciding the reverse path for those ICMP messages.

This bug only affects IPV4, not in IPv6.

v1->v2:  restructure the patches into two patches that fix defragmentation and
         fragmentation respectively.

	 A bit is add in IPCB to control whether ICMP packet should be
	 generated for defragmentation.

	 Fragmentation ICMP is now removed by restructuring the
	 ip_fragment() API.

v2->v3:  Add droping icmp for bridging contrack users
         drop exporting ip_fragment() API.

v3->v4:  Remove unnecessary parentheses in 'return' statements

v4->v5:  Drop the patch that sets and checks a bit in IPCB
         that prevents ip_defrag to send ICMP.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When bridge netfilter re-fragments an IP packet for output, all
packets that can not be re-fragmented to their original input size
should be silently discarded.

However, current bridge netfilter output path generates an ICMP packet
with 'size exceeded MTU' message for such packets, this is a bug.

This patch refactors the ip_fragment() API to allow two separate
use cases. The bridge netfilter user case will not
send ICMP, the routing output will, as before.
Signed-off-by: NAndy Zhou <azhou@nicira.com>
Acked-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

users in [IP_DEFRAG_CONNTRACK_BRIDGE_IN, __IP_DEFRAG_CONNTRACK_BR_IN]
should not ICMP message also.
Reported-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NAndy Zhou <azhou@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Improve readability of skip ICMP for de-fragmentation expiration logic.
This change will also make the logic easier to maintain when the
following patches in this series are applied.
Signed-off-by: NAndy Zhou <azhou@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

psock_fanout tests the various fanout modes. Change the test for
rollover mode to expect early rollover due to socket pressure
as implemented in 2ccdbaa6 ("packet: rollover lock contention
avoidance").
Signed-off-by: NWillem de Bruijn <willemb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We expect that MC_CMD_SRIOV will fail if the card has no VFs configured.
So output a readable message instead of a cryptic MCDI error.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter updates for net-next

The following patchset contains Netfilter updates for net-next. Briefly
speaking, cleanups and minor fixes for ipset from Jozsef Kadlecsik and
Serget Popovich, more incremental updates to make br_netfilter a better
place from Florian Westphal, ARP support to the x_tables mark match /
target from and context Zhang Chunyu and the addition of context to know
that the x_tables runs through nft_compat. More specifically, they are:

1) Fix sparse warning in ipset/ip_set_hash_ipmark.c when fetching the
   IPSET_ATTR_MARK netlink attribute, from Jozsef Kadlecsik.

2) Rename STREQ macro to STRNCMP in ipset, also from Jozsef.

3) Use skb->network_header to calculate the transport offset in
   ip_set_get_ip{4,6}_port(). From Alexander Drozdov.

4) Reduce memory consumption per element due to size miscalculation,
   this patch and follow up patches from Sergey Popovich.

5) Expand nomatch field from 1 bit to 8 bits to allow to simplify
   mtype_data_reset_flags(), also from Sergey.

6) Small clean for ipset macro trickery.

7) Fix error reporting when both ip_set_get_hostipaddr4() and
   ip_set_get_extensions() from per-set uadt functions.

8) Simplify IPSET_ATTR_PORT netlink attribute validation.

9) Introduce HOST_MASK instead of hardcoded 32 in ipset.

10) Return true/false instead of 0/1 in functions that return boolean
    in the ipset code.

11) Validate maximum length of the IPSET_ATTR_COMMENT netlink attribute.

12) Allow to dereference from ext_*() ipset macros.

13) Get rid of incorrect definitions of HKEY_DATALEN.

14) Include linux/netfilter/ipset/ip_set.h in the x_tables set match.

15) Reduce nf_bridge_info size in br_netfilter, from Florian Westphal.

16) Release nf_bridge_info after POSTROUTING since this is only needed
    from the physdev match, also from Florian.

17) Reduce size of ipset code by deinlining ip_set_put_extensions(),
    from Denys Vlasenko.

18) Oneliner to add ARP support to the x_tables mark match/target, from
    Zhang Chunyu.

19) Add context to know if the x_tables extension runs from nft_compat,
    to address minor problems with three existing extensions.

20) Correct return value in several seqfile *_show() functions in the
    netfilter tree, from Joe Perches.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ursula Braun says:

====================
s390: network patches for net-next

here are s390 related patches for net-next
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

An attempt to configure a CTC device as LCS results in the
following error message:

  (null): Detecting a network adapter for LCS devices failed
          with rc=-5 (0xfffffffb)

"(null)" results from access to &card->dev->dev in lcs_new_device()
which is only initialized later in the function. Fix this by using
&ccwgdev->dev instead which is initialized before lcs_new_device()
is called.
Signed-off-by: NPeter Oberparleiter <oberpar@linux.vnet.ibm.com>
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since recently, `checkpatch.pl` advices that ENOSYS should not be
used for anything other than "invalid syscall nr". This patch
replaces ENOSYS return code with EOPNOTSUPP for the "unsupported
function" conditions.
Signed-off-by: NEugene Crosser <Eugene.Crosser@ru.ibm.com>
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Forbid enabling IFF_PROMISC reflection to BRIDGEPORT when a role
is already assigned, and forbid direct manipulation of the role
when reflection mode is engaged.
Reviewed-by: NThomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: NEugene Crosser <Eugene.Crosser@ru.ibm.com>
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

OSA Ethernet hardware is introducing BRIDGEPORT functionality
similar (but not identical) to HiperSockets BRIDGEPORT. This
patch makes HiperSockets BRIDGEPORT related sysfs attributes
and udev events work with OSA hardware too.
Reviewed-by: NThomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: NEugene Crosser <Eugene.Crosser@ru.ibm.com>
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

OSA and HiperSocket devices do not support promiscuous mode proper,
but they support "BRIDGE PORT" mode that is functionally similar.
This update introduces sysfs attribute that, when set, makes the driver
try to "reflect" setting and resetting of the IFF_PROMISC flag on the
interface into setting and resetting PRIMARY or SECONDARY bridge port
role on the underlying OSA or HiperSocket device.
Reviewed-by: NThomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: NEugene Crosser <Eugene.Crosser@ru.ibm.com>
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Locking is probably unnecessary in this case, and the rest of the
qeth sysfs code does not use locks in the *_show() functions.
Remove locks from the layer2 *_show() functions in which they where
accidentally introduced.
Signed-off-by: NEugene Crosser <Eugene.Crosser@ru.ibm.com>
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Function that executes IPA commands returns the result code from the
IPA response block. If non-negative, it needs to be transformed into
errno-compatible code before returning to the caller.
Signed-off-by: NEugene Crosser <Eugene.Crosser@ru.ibm.com>
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ethtool is used to change some device driver features
such as RX/TX hardware checksum offloading.
The qeth device driver callback function to
turn on/off RX hardware check sum handling never changes
the hardware configuration.
The NETIF_F_RXCSUM bit is cleared when the feature bitset
type netdev_features_t(64bit) is assigned to 32 a bit
variable.

This patch fixes the NETIF_F_RXCSUM handling.
Also there is no need to manipulate the device's features
bit set as this is done by the caller when no error occurs.
Signed-off-by: NThomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently we use a global rover to select a port ID that is unique.
This used to work consistently when it was protected with a global
lock.  However as we're now lockless, the global rover can exhibit
pathological behaviour should multiple threads all stomp on it at
the same time.

Granted this will eventually resolve itself but the process is
suboptimal.

This patch replaces the global rover with a pseudorandom starting
point to avoid this issue.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The spinlock is used to protect netns_ids which is per net,
so there is no need to use a global spinlock.

Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Acked-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MoCA interfaces require the use of an user-space daemon (mocad) which
will typically use cmd->autoneg to force the link. This is causing other
network manager applications not to get proper carrier down
notifications because of the following sequence of events:

- link down interrupt is received, link is set to 0 by the interrupt
  handler
- fixed_link update callback runs and updates the BMSR register
  accordingly
- PHY library polls the PHY for link status, sees the link is down,
  proceeds with reporting that
- mocad gets notified of the link state and call phy_ethtool_sset()
  with cmd->autoneg set to the link status (0)
- phy_start_aneg() is called at the end of phy_ethtool_sset() and sets
  the PHY state to PHY_FORCING

Just make sure we notify the interface carrier appropriately when we
detect that the link is down in our fixed_link update callback. This is
made local to the bcm_sf2 driver as the PHY library does the right thing
in any case. This is similar to the GENET change introduced in
54d7c01d ("net: bcmgenet: enable MoCA
link state change detection").

Fixes: 246d7f77 ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes: 06635a35 ("flow_dissect: use programable dissector in skb_flow_dissect and friends")
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the struct netvsc_stats has a member s_sync
of type u64_stats_sync.
This definition will break kernel build as the macro
netdev_alloc_pcpu_stats requires this member name to be syncp.
(see netdev_alloc_pcpu_stats definition in ./include/linux/netdevice.h)

This patch changes netvsc_stats's member name from s_sync to syncp to fix
the build break.
Signed-off-by: NSimon Xiao <sixiao@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>