- 15 6月, 2016 7 次提交
-
-
由 Michael Chan 提交于
Newer chips require different logic to handle GRO packets. So refactor the code so that we can call different functions depending on the chip. Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Define all the supported chip numbers and chip categories. Store the chip_num returned by firmware. If the call to get the version and chip number fails, we should abort. Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Satish Baddipadige 提交于
NPAR type is read from bnxt_hwrm_func_qcfg. Do not allow changing link parameters if in NPAR mode sinc ethe port is shared among multiple partitions. The link parameters are set up by firmware. Signed-off-by: NSatish Baddipadige <sbaddipa@broadcom.com> Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
When the VF driver gets this event, the VF configuration has changed (such as default VLAN). The VF driver will initiate a silent reset to pick up the new configuration. Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
When a default VLAN is added to the VF, the VF driver needs to reset to pick up the default VLAN ID. We can use the same tx timeout reset logic to do that, without the debug output. This new function, with the silent parameter to suppress debug output will now serve both purposes. Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
The PF can setup a default VLAN for a VF. The default VLAN tag is automatically inserted and stripped without the knowledge of the stack running on the VF. The VF driver needs to know that default VLAN is enabled as VLAN acceleration on the RX side is no longer supported. Call netdev_update_features() to fix up the VLAN features as necessary. Also, VLAN strip mode must be enabled to strip out the default VLAN tag. Only allow VF default VLAN to be set if the firmware spec is >= 1.2.1. Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 10 6月, 2016 3 次提交
-
-
由 Florian Fainelli 提交于
Add a few netdev statistics to report transmitted and received bytes and packets and a few obvious errors. Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Florian Fainelli 提交于
Read the statistics from the BGMAC's builtin MAC and return them to user-space using the standard ethtool helpers. Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Florian Fainelli 提交于
In preparation for allowing different helpers to be utilized against network devices created by the bgmac driver, make sure that we bind the net_device with core->dev. Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 08 6月, 2016 3 次提交
-
-
由 Michael Chan 提交于
Since both CTAG and STAG rx acceleration must be enabled together, we only need to check one feature flag (NETIF_F_HW_VLAN_CTAG_RX) before calling __vlan_hwaccel_put_tag(). Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
The hardware can only be set to strip or not strip both the VLAN CTAG and STAG. It cannot strip one and not strip the other. Add logic to bnxt_fix_features() to toggle both feature flags when the user is toggling one of them. Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Set the is_push flag in the software BD before the tx data is pushed to the chip. It is possible to get the tx interrupt as soon as the tx data is pushed. The tx handler will not handle the event properly if the is_push flag is not set and it will crash. Signed-off-by: NMichael Chan <michael.chan@broadocm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 06 6月, 2016 1 次提交
-
-
由 Michal Schmidt 提交于
Since implementing VLAN filtering in commit 05cc5a39 ("bnx2x: add vlan filtering offload") bnx2x refuses to add a VLAN while the interface is down: # ip link add link enp3s0f0 enp3s0f0_10 type vlan id 10 RTNETLINK answers: Bad address and in dmesg (with bnx2x.debug=0x20): bnx2x: [bnx2x_vlan_rx_add_vid:12941(enp3s0f0)]Ignoring VLAN configuration the interface is down Other drivers have no problem with this. Fix this peculiar behavior in the following way: - Accept requests to add/kill VID regardless of the device state. Maintain the requested list of VIDs in the bp->vlan_reg list. - If the device is up, try to configure the VID list into the hardware. If we run out of VLAN credits or encounter a failure configuring an entry, fall back to accepting all VLANs. If we successfully configure all entries from the list, turn the fallback off. - Use the same code for reconfiguring VLANs during NIC load. Signed-off-by: NMichal Schmidt <mschmidt@redhat.com> Acked-by: NYuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 01 6月, 2016 1 次提交
-
-
由 Vitaly Kuznetsov 提交于
bnx2x_init_bp() allocates memory with bnx2x_alloc_mem_bp() so if we fail later in bnx2x_init_one() we need to free this memory with bnx2x_free_mem_bp() to avoid leakages. E.g. I'm observing memory leaks reported by kmemleak when a failure (unrelated) happens in bnx2x_vfpf_acquire(). Signed-off-by: NVitaly Kuznetsov <vkuznets@redhat.com> Acked-by: NYuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 21 5月, 2016 1 次提交
-
-
由 Tom Herbert 提交于
This patch defines two new GSO definitions SKB_GSO_IPXIP4 and SKB_GSO_IPXIP6 along with corresponding NETIF_F_GSO_IPXIP4 and NETIF_F_GSO_IPXIP6. These are used to described IP in IP tunnel and what the outer protocol is. The inner protocol can be deduced from other GSO types (e.g. SKB_GSO_TCPV4 and SKB_GSO_TCPV6). The GSO types of SKB_GSO_IPIP and SKB_GSO_SIT are removed (these are both instances of SKB_GSO_IPXIP4). SKB_GSO_IPXIP6 will be used when support for GSO with IP encapsulation over IPv6 is added. Signed-off-by: NTom Herbert <tom@herbertland.com> Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 16 5月, 2016 9 次提交
-
-
由 Michael Chan 提交于
Use the weaker but more appropriate dma_rmb() to order the reading of the completion ring. Suggested-by: NAjit Khaparde <ajit.khaparde@broadcom.com> Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
The current code is more complicated than necessary and can only report unsupported SFP+ module if it is plugged in after the device is up. Rename bnxt_port_module_event() to bnxt_get_port_module_status(). We already have the current module_status in the link_info structure, so just check that and report any unsupported SFP+ module status. Delete the unnecessary last_port_module_event. Call this function at the end of bnxt_open to report unsupported module already plugged in. Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
The len value in the hwrm error message is wrong. Use the properly adjusted value in the variable len. Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
The current code has 2 problems: 1. The maximum wait time is not long enough. It is about 60% of the duration specified by the firmware. It is calling usleep_range(600, 800) for every 1 msec we are supposed to wait. 2. The granularity of the delay is too coarse. Many simple firmware commands finish in 25 usec or less. We fix these 2 issues by multiplying the original 1 msec loop counter by 40 and calling usleep_range(25, 40) for each iteration. There is also a second delay loop to wait for the last DMA word to complete. This delay loop should be a very short 5 usec wait. This change results in much faster bring-up/down time: Before the patch: time ip link set p4p1 up real 0m0.120s user 0m0.001s sys 0m0.009s After the patch: time ip link set p4p1 up real 0m0.030s user 0m0.000s sys 0m0.010s Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
The chip supports 4K/8K/64K page sizes for the rings and we try to match it to the CPU PAGE_SIZE. The current page size limits for the rings are based on 4K/8K page size. If the page size is 64K, these limits are too large. Reduce them appropriately. Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ajit Khaparde 提交于
Add code to log a message during driver load indicating PCIe link speed and width. The log message will look like this: bnxt_en 0000:86:00.0 eth0: PCIe: Speed 8.0GT/s Width x8 Signed-off-by: NAjit Khaparde <ajit.khaparde@broadcom.com> Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ajit Khaparde 提交于
Add support to fetch the SFP EEPROM settings from the firmware and display it via the ethtool -m command. We support SFP+ and QSFP modules. v2: Fixed a bug in bnxt_get_module_eeprom() found by Ben Hutchings. Signed-off-by: NAjit Khaparde <ajit.khaparde@broadcom.com> Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Satish Baddipadige 提交于
When there is only 1 MSI-X vector or in INTA mode, tx and rx pre-set max channel parameters are shown incorrectly in ethtool -l. With only 1 vector, bnxt_get_max_rings() will return -ENOMEM. bnxt_get_channels should check this return value, and set max_rx/max_tx to 0 if it is non-zero. Signed-off-by: NSatish Baddipadige <sbaddipa@broadcom.com> Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 12 5月, 2016 2 次提交
-
-
由 Michael Chan 提交于
Add detection and recovery code when the hardware returned opaque value does not match the expected consumer index. Once the issue is detected, we skip the processing of all RX and LRO/GRO packets. These completion entries are discarded without sending the SKB to the stack and without producing new buffers. The function will be reset from a workqueue. Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
There is a rare hardware bug that can cause a bad opaque value in the RX or TPA completion. When this happens, the hardware may have used the same buffer twice for 2 rx packets. In addition, the driver will also crash later using the bad opaque as the index into the ring. The rx opaque value is predictable and is always monotonically increasing. The workaround is to keep track of the expected next opaque value and compare it with the one returned by hardware during RX and TPA start completions. If they miscompare, we will not process any more RX and TPA completions and exit NAPI. We will then schedule a workqueue to reset the function. This patch adds the logic to keep track of the next rx consumer index. Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 07 5月, 2016 1 次提交
-
-
由 Jon Maxwell 提交于
We recently had a system crash in the cnic module. Vmcore analysis confirmed that "ip link up" was executed which failed due to an allocation failure because of memory fragmentation. Futher analysis revealed that the cnic irq vector was still allocated after the "ip link up" that failed. When "ip link down" was executed it called free_msi_irqs() which crashed the system because the cnic irq was still inuse. PANIC: "kernel BUG at drivers/pci/msi.c:411!" The code execution was: cnic_netdev_event() if (event == NETDEV_UP) { . . ▹ if (!cnic_start_hw(dev)) cnic_start_hw() calls cnic_cm_open() which failed with -ENOMEM cnic_start_hw() then took the err1 path: err1:
↩ cp->free_resc(dev);↩ <---- frees resources but not irq vector pci_dev_put(dev->pcidev);↩ return err;↩ }↩ This returns control back to cnic_netdev_event() but now the cnic irq vector is still allocated even although cnic_cm_open() failed. The next "ip link down" while trigger the crash. The cnic_start_hw() routine is not handling the allocation failure correctly. Fix this by checking whether CNIC_DRV_STATE_HANDLES_IRQ flag is set indicating that the hardware has been started in cnic_start_hw(). If it has then call cp->stop_hw() which frees the cnic irq vector and cnic resources. Otherwise just maintain the previous behaviour and free cnic resources. I reproduced this by injecting an ENOMEM error into cnic_cm_alloc_mem()s return code. # ip link set dev enpX down # ip link set dev enpX up <--- hit's allocation failure # ip link set dev enpX down <--- crashes here With this patch I confirmed there was no crash in the reproducer. Signed-off-by: NJon Maxwell <jmaxwell37@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 05 5月, 2016 4 次提交
-
-
由 Michael Chan 提交于
The multicast/all-multicast internal flags are not properly restored after device reset. This could lead to unreliable multicast operations after an ethtool configuration change for example. Call bnxt_mc_list_updated() and setup the vnic->mask in bnxt_init_chip() to fix the issue. Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
The code determines if the next ring entry is valid before proceeding further to read the rest of the entry. The CPU can re-order and read the rest of the entry first, possibly reading a stale entry, if DMA of a new entry happens right after reading it. This issue can be readily seen on a ppc64 system, causing it to crash. Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Florian Westphal 提交于
Replace all trans_start updates with netif_trans_update helper. change was done via spatch: struct net_device *d; @@ - d->trans_start = jiffies + netif_trans_update(d) Compile tested only. Cc: user-mode-linux-devel@lists.sourceforge.net Cc: linux-xtensa@linux-xtensa.org Cc: linux1394-devel@lists.sourceforge.net Cc: linux-rdma@vger.kernel.org Cc: netdev@vger.kernel.org Cc: MPT-FusionLinux.pdl@broadcom.com Cc: linux-scsi@vger.kernel.org Cc: linux-can@vger.kernel.org Cc: linux-parisc@vger.kernel.org Cc: linux-omap@vger.kernel.org Cc: linux-hams@vger.kernel.org Cc: linux-usb@vger.kernel.org Cc: linux-wireless@vger.kernel.org Cc: linux-s390@vger.kernel.org Cc: devel@driverdev.osuosl.org Cc: b.a.t.m.a.n@lists.open-mesh.org Cc: linux-bluetooth@vger.kernel.org Signed-off-by: NFlorian Westphal <fw@strlen.de> Acked-by: NFelipe Balbi <felipe.balbi@linux.intel.com> Acked-by: NMugunthan V N <mugunthanvnm@ti.com> Acked-by: NAntonio Quartulli <a@unstable.cc> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Alexander Duyck 提交于
This patch assumes that the bnxt hardware will ignore existing IPv4/v6 header fields for length and checksum as well as the length and checksum fields for outer UDP and GRE headers. I have been told by Michael Chan that this is working. Though this might be somewhat redundant for IPv6 as they are forcing the checksum to be computed for all IPv6 frames that are offloaded. A follow-up patch may be necessary in order to fix this as it is essentially mangling the outer IPv6 headers to add a checksum where none was requested. Signed-off-by: NAlexander Duyck <aduyck@mirantis.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 28 4月, 2016 4 次提交
-
-
由 Masanari Iida 提交于
This patch fix spelling typos in printk from various part of the codes. Signed-off-by: NMasanari Iida <standby24x7@gmail.com> Acked-by: NRandy Dunlap <rdunlap@infradead.org> Signed-off-by: NJiri Kosina <jkosina@suse.cz>
-
由 Michael Chan 提交于
If PAGE_SIZE is bigger than BNXT_RX_PAGE_SIZE, that means the native CPU page is bigger than the maximum length of the RX BD. Divide the page into multiple 32K buffers for the aggregation ring. Add an offset field in the bnxt_sw_rx_agg_bd struct to keep track of the page offset of each buffer. Since each page can be referenced by multiple buffer entries, call get_page() as needed to get the proper reference count. Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
The RX BD length field of this device is 16-bit, so the largest buffer size is 65535. For LRO and GRO, we allocate native CPU pages for the aggregation ring buffers. It won't work if the native CPU page size is 64K or bigger. We fix this by defining BNXT_RX_PAGE_SIZE to be native CPU page size up to 32K. Replace PAGE_SIZE with BNXT_RX_PAGE_SIZE in all appropriate places related to the rx aggregation ring logic. The next patch will add additional logic to divide the page into 32K chunks for aggrgation ring buffers if PAGE_SIZE is bigger than BNXT_RX_PAGE_SIZE. Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Only MSI-X can be used on a VF. The driver should fail initialization if it cannot successfully enable MSI-X. Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 22 4月, 2016 2 次提交
-
-
由 Florian Fainelli 提交于
By using napi_complete_done(), we allow fine tuning of /sys/class/net/ethX/gro_flush_timeout for higher GRO aggregation efficiency for a Gbit NIC. Check commit 24d2e4a5 ("tg3: use napi_complete_done()") for details. Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Florian Fainelli 提交于
Both bcm_sysport_tx_isr() and bcm_sysport_rx_isr() run in hard irq context, we do not need to block irq again. Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 17 4月, 2016 1 次提交
-
-
由 Eric Dumazet 提交于
On 64bit kernels, device stats are 64bit wide, not 32bit. Fixes: 1c1008c7 ("net: bcmgenet: add main driver file") Signed-off-by: NEric Dumazet <edumazet@google.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 15 4月, 2016 1 次提交
-
-
由 Felix Fietkau 提交于
Only core revisions older than 4 use BGMAC_CMDCFG_SR_REV0. This mainly fixes support for BCM4708A0KF SoCs with Ethernet core rev 5 (it means only some devices as most of BCM4708A0KF-s got core rev 4). This was tested for regressions on BCM47094 which doesn't seem to care which bit gets used. Signed-off-by: NFelix Fietkau <nbd@openwrt.org> Signed-off-by: NRafał Miłecki <zajec5@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-