after looking it up, all rants about the 80 columns restriction seem to
be in vain. After changing the card's name it are now "only" seven new
lines in the tiny DVB-T/DVB-S switch function.

saa7130/34: v4l2 driver version 0.2.14 loaded
saa7133[0]: found at 0000:02:08.0, rev: 209, irq: 18, latency: 32, mmio: 0xfdef7000
saa7133[0]: subsystem: 1043:4878, board: Asus Tiger 3in1 [card=147,autodetected]
saa7133[0]: board init: gpio is 200000
tuner' 2-004b: chip found @ 0x96 (saa7133[0])
saa7133[0]: i2c eeprom 00: 43 10 78 48 54 20 1c 00 43 43 a9 1c 55 d2 b2 92
saa7133[0]: i2c eeprom 10: ff ff ff 0f ff 20 ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 20: 01 40 01 02 03 01 01 03 08 ff 00 d7 ff ff ff ff
saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 40: ff 28 00 c2 96 16 03 02 c0 1c ff ff ff ff ff ff
saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom e0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom f0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c scan: found device @ 0x10  [???]
saa7133[0]: i2c scan: found device @ 0x16  [???]
saa7133[0]: i2c scan: found device @ 0x1c  [???]
saa7133[0]: i2c scan: found device @ 0x96  [???]
saa7133[0]: i2c scan: found device @ 0xa0  [eeprom]
tda829x 2-004b: setting tuner address to 61
tda829x 2-004b: type set to tda8290+75a
saa7133[0]: registered device video0 [v4l2]
saa7133[0]: registered device vbi0
saa7133[0]: registered device radio0

DVB: registering new adapter (saa7133[0])
DVB: registering frontend 0 (Philips TDA10086 DVB-S)...

The board init gpio is 0x0, 0x200000 is from previously unloading with
antenna_switch = 1.

It needs firmware for the tda10046 and analog sound needs saa7134-alsa.

I have support for one more board and need to fix the first revision of
the Asus Tiger DVB-T hybrid. DVB-T currently hangs on the male radio
antenna input, also some small other stuff.

Please report any issues with this patch, the next are depending on this
one.

saa7134: add support for the triple Asus Tiger 3in1
Signed-off-by: NHermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add support for ST STV0288 demodulator and cards with it,
such as TeVii S420.
Patch is co-authored with Georg Acher <acher@baycom.de>
Signed-off-by: NGeorg Acher <acher@baycom.de>
Signed-off-by: NIgor M. Liplianin <liplianin@me.by>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

We don't want to push the ISDB-T definitions into the kernel until
we have a high level of confidence in the ISDB-T API. More testing
is required before this code is released.
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Patch by Darron Broad.
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Patch provided by Darron Broad.
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Patch provided by Darron Broad
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Added support for TBS 8920 DVB-S/S2 card. The card
based on cx24116 demodulator.
Signed-off-by: NOleg Roitburd <oroitburd@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Added support for Omicom SS4 DVB-S/S2 card. The card
based on cx24116 demodulator.
Signed-off-by: NOleg Roitburd <oroitburd@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add support for USB card modification with SI2109/2110 demodulator.
Signed-off-by: NIgor M. Liplianin <liplianin@me.by>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add support for Silicon Laboratories SI2109/2110 demodulator
and cards with it, such as DvbWorld PCI2002.
Signed-off-by: NIgor M. Liplianin <liplianin@me.by>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

From the author:
This patch-set fixes remote control issues I have experienced
with hauppauge drivers in Linux since the PVR-350 and now
with both a NOVA-S+ and HVR-4000. It has also been confirmed
to work with an HVR-1300 user who had exactly the same issue.

Hauppage remote controls use RC5. RC5 has a bit-field which
represents the target device. The hauppauge windows drivers
have a registry key which can enable filtering, but the linux
drivers will accept any target device in this bit field for
internal processing.

This causes problems with setups such as mythtv where remote
control key presses destined for the TV (target = 0) are
interpreted by the kernel and subsequenctly LIRC then mythtv.

Of the remote controls I have to hand (wintv black, pvr/hvr
silver) the hauppauge remotes send one of two device targets
ids, these are interpreted by the patch which then filters
out any non hauppauge addresses.
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NDarron Broad <darron@kewl.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

From the author:
Here is a simple patch detailing some reverse engineered
register detail lost in my latest merge. The comments
in the code refer to this register but it is never
defined. This corrects this.
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NDarron Broad <darron@kewl.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Adjust MPEG initialization in cx24116 in order to accomodate different
MPEG CLK position and polarity in different cards. For example, HVR4000
uses 0x02 value, but DvbWorld & TeVii USB cards uses 0x01. Without it MPEG
stream was broken on that cards for symbol rates > 30000 kSyms/s.
Signed-off-by: NIgor M. Liplianin <liplianin@me.by>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Remove the debugging sysctls.
Rolloff was broken, not it works as expected and has been tested in kaffeine.
Power related changes for the isl6421 are not implemented on the HVR4000/4000LITE.
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NDarron Broad <darron@kewl.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add support for DvbWorld 2004 DVB-S2 PCI adapter.
The card contains dm1105 PCI chip and cx24116 demodulator
Signed-off-by: NIgor M. Liplianin <liplianin@me.by>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

I was given these changes by Darron Broad and Igor Liplianin and represent a series
of patches they've been making to the cx24116 driver over the last two years.

Changes for handling symbolrates >30Ksps
Tone handling changes.
Diseqc support.
Sleep support, shutting down the clocks correctly.
Cleanup on ROLL_OFF and PILOT support.

*** ST - We need to cleanup the sysclt control, this is abnormal
    in a demod driver. We should work towards understanding the missing
    API's and ensure we have them in S2API.  ***
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NDarron Broad <darron@kewl.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add support for SDMC DM1105 PCI chip. There is a lot of
cards based on it, like DvbWorld 2002 DVB-S , 2004 DVB-S2
Signed-off-by: NIgor M. Liplianin <liplianin@me.by>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Many thanks to Darron Broad for pointing out the obvious.
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Also added some compat code for the older API.

Added more ISDB message/command suggestions, current not connected in dvb-core.
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Bug fix: ioctl FE_SET_PROPERTY/FE_GET_PROPERTY always return error
Signed-off-by: NIgor M. Liplianin <liplianin@me.by>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The frontends will be notified (if they chose) of all _get and _set commands
so they can help determine result or action. Results are now returned
to userspace correctly.
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The API now assumes that ioctl calls for FE_SET_PROPERTY and all
set commands, and FE_GET_PROPERTY are get commands.

Simplification.
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This helps complex demods which support different modulation types
be better informed.
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

For demod drivers, we want a single tuning function (set_frontend) to have
access to the properly constructed dvb_frontend_parameters structure, or
the cache values - regardless of whether the legacy or new API is being used.

This cuts down on redundant code in the demod drivers and ensures the
tuning parameters are consistent regardless of the API entry type.
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This is now consistent with the existing API.
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

After discussion the following changes were made:
1. Removed the typedefs in frontend.h, use structures.
2. In the frontend.h, remove the 16 command limit on the API and
   switch to a flexible variable length API. For practical reasons
   a #define limits this to 64, this should be discussed.
3. Changed dvb-core ioctl handing to deal with variable sequences
   of commands.

tune-v0.0.3.c is required to use this API, it contains the interface changes.
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The group preferred dtv_ over tv_, this implements it.
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Adjust MPEG initialization in cx24116 in order to accomodate different
MPEG CLK position and polarity in different cards.
Signed-off-by: NIgor M. Liplianin <liplianin@me.by>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

cx24116: Fix lock for high (above 30000 kSyms) symbol rates
Signed-off-by: NIgor M. Liplianin <liplianin@me.by>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Change menu item in Kconfig for DVBWorld 2104 and TeVii S650 USB DVB-S2 cards
Signed-off-by: NIgor M. Liplianin <liplianin@me.by>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Added support for DVBWorld 2104 and TeVii S650 USB DVB-S2 cards
This cards based on cx24116 demodulator.
Signed-off-by: NIgor M. Liplianin <liplianin@me.by>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Thanks to Hans Werner for finding the problem.
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Added support for TeVii S460 DVB-S/S2 card. The card
based on cx24116 demodulator.
Signed-off-by: NIgor M. Liplianin <liplianin@me.by>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

SET_TONE and SET_VOLTAGE were not previously implemented. Two options
existed. Either cut/paste from the previous ioctl handler into the
process_properties function, which is code duplication. Or, split
the current ioctl handler into it's two major pieces.

Piece 1, responsible for input validation and semaphore acquiring
Piece 2 the processing of the previous ioctls

and finally, a new third pieces where the array of properties
is processed, and can freely call the legacy ioctl handler without
having to re-acquire the fepriv->sem semaphore. This is a clean approach
and ensures the existing legacy ioctls are processed as they were previously
(but with an extra function call) and allows the new API to share code
without duplication.
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>