DCDC3 supplies voltage to DDR. Fix DCDC3 volatge to 1.5V which is the reset
value. Programming to a non-reset value while executing from DDR will result
in random hangs.
Signed-off-by: NKeerthy <j-keerthy@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

DCDC3 supplies voltage to DDR. Fix DCDC3 volatge to 1.5V which is the reset
value. Programming to a non-reset value while executing from DDR will result
in random hangs.
Signed-off-by: NKeerthy <j-keerthy@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The 5th NAND partition should be named "NAND.u-boot-spl-os"
instead of "NAND.u-boot-spl". This is to be consistent with other
TI boards as well as u-boot.

Fixes: 91994fac ("ARM: dts: am335x-evm: NAND: update MTD partition table")
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

We're moving omaps to use device tree based booting and already have
omap2, omap4, omap5, am335x and am437x booting in device tree only
mode.

Only omap3 still has legacy booting still around and we really want
to make that device tree only. So let's add a warning about deprecated
legacy booting so we get people to upgrade their boards to use device
tree based booting and find out about any remaining issues.

Note that for most boards we already have the .dts file and those can
be booted with without changing the bootloader using the appended
DTB mode.
Acked-By: NSebastian Reichel <sre@kernel.org>
Reviewed-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: NJavier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Looks like we need to have BCH enabled to get NAND
working and to avoid getting:

nand: error: CONFIG_MTD_NAND_ECC_BCH not enabled
Signed-off-by: NTony Lindgren <tony@atomide.com>

Commit  673ce00c (ARM: omap2plus_defconfig: Add support for
distros with systemd) caused considerable bloat as noted by
Paul Walmsley <paul@pwsan.com>.

Let's fix this issue by making what we can into loadable modules
for the systemd options. That's only IPV6 and AUTOFS4_FS it
seems, and IPv6 defaults to a loadable module.
Reported-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Commit 78b81f46 ("ARM: dts: imx28-evk: Run I2C0 at 400kHz") caused issues
when doing the following sequence in loop:

- Boot the kernel
- Perform audio playback
- Reboot the system via 'reboot' command

In many times the audio card cannot be probed, which causes playback to fail.

After restoring to the original i2c0 frequency of 100kHz there is no such
problem anymore.

This reverts commit 78b81f46.

Cc: <stable@vger.kernel.org> # 3.16+
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Fix a typo error, the "emi" names refer to the eim clocks.

The change fixes typo in EIM and EIM_SLOW pre-output dividers and
selectors clock names. Notably EIM_SLOW clock itself is named correctly.
Signed-off-by: NSteve Longerbeam <steve_longerbeam@mentor.com>
[vladimir_zapolskiy@mentor.com: ported to v3.17]
Signed-off-by: NVladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Allows booting from SD/MMC on RK3288 and other platforms. Added here so I
can enable the board in the boot farm.
Signed-off-by: NOlof Johansson <olof@lixom.net>

I missed in 9a2ad529 that REGULATOR_FIXED_VOLTAGE had also gotten
deselected, so it needs to be added back as an explicit option.
Signed-off-by: NOlof Johansson <olof@lixom.net>

Without the 3.3V regulator node, the SDMMC driver will give these warnings:

dw_mmc ff704000.dwmmc0: No vmmc regulator found
dw_mmc ff704000.dwmmc0: No vqmmc regulator found

This patch adds the regulator node, and points the SD/MMC to the regulator.
Signed-off-by: NDinh Nguyen <dinguyen@opensource.altera.com>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
---
v3: Rename nodes to have schematic-name_regulator and remove "boot-on" and
    "always-on"
v2: Move the regulator nodes to their respective board dts file and
    correctly rename them to match the schematic

Without this patch, the booting the SOCFPGA platform would hang at the
SDMMC driver loading. The issue, debugged by Doug Anderson, turned out
to be that the GPIO bank used by the SD card-detect was not set to
status="okay".

Also update the cd-gpios to point to portb of the &gpio1 GPIO IP.
Suggested-by: NDoug Anderson <dianders@chromium.org>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NDinh Nguyen <dinguyen@opensource.altera.com>
---
v4: Use &gpio1 to set status="okay" and update cd-gpio=&portb
v3: Correctly degugged the issue to be a gpio node not having status="okay"

Since the Synopsys GPIO IP can support multiple ports of varying widths, it
would make more sense to have the GPIO node DTS entry as this:

gpio0: gpio@ff708000{
	porta{
	};
};

Also, this is documented in the snps-dwapb-gpio.txt.
Suggested-by: NDoug Anderson <dianders@chromium.org>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NDinh Nguyen <dinguyen@opensource.altera.com>

PLLB input and output ranges were wrongly copied from at91sam9261 as the
datasheet didn't mention explicitly PLLB. Correct their values.

This fixes USB.
Reported-by: NAndreas Henriksson <andreas.henriksson@endian.se>
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Tested-by: NAndreas Henriksson <andreas.henriksson@endian.se>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

When CPU1 is brought out of reset, it's MMU is not turned on yet, so it will
only be able to use physical addresses. For systems with that have the
MMU page configured for 0xC0000000, 0x80000000, or 0x40000000
"BIC 0x40000000" will work just fine, as it was just converting the
virtual address of &cpu1start_addr into a physical address, ie. 0xC0000000
became 0x80000000. So for systems where the SDRAM controller was able to do a
wrap-around access, this was working fine, as it was just dropping the MSB,
but for systems where out of bounds memory access is not allowed, this would
not allow CPU1 to correctly fetch &cpu1start_addr.

This patch fixes the secondary_trampoline code to correctly fetch the
physical address of cpu1start_addr directly. The patch will subtract the
correct PAGE_OFFSET from &cpu1start_addr. And since on this platform, the
physical memory will always start at 0x0, subtracting PAGE_OFFSET from
&cpu1start_addr will allow CPU1 to correctly fetch the value of cpu1start_addr.

While at it, change the name of cpu1start_addr to socfpga_cpu1start_addr
to avoid any future naming collisions for multiplatform image.
Signed-off-by: NDinh Nguyen <dinguyen@opensource.altera.com>
---
v4: Updated commit log to correctly lay out the usage of PAGE_OFFSET and
    add comments to the same effect.
v3: Used PAGE_OFFSET to get the physical address
v2: Correctly get the physical address instead of just a BIC hack.

Update the multi_v7_defconfig enabling the watchdog driver for Meson
SoCs.
Signed-off-by: NCarlo Caione <carlo@caione.org>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

sed -i 's/}\ ;/};/g'
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Add the cadence watchdog node to the Zynq devicetree.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Add missing reference for memory-controller.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Add missing reference for ADC node.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

By in sync with others node and add also baseaddr
to the node name.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Due to dependencies between timer and CPU frequency, only changes by
powers of two are allowed. The clocksource driver prevents other
changes, but with cpufreq and its governors it can result in being
spammed with error messages constantly. Hence, remove the 222 MHz OPP.
Signed-off-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

The size of the GEM's register area is only 0x1000 bytes.
Signed-off-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Explicitly set the dr_mode for the second dwc3 controller on the
Arndale Octa board to host mode. This is required to ensure the
controller is initialized in the right mode if the kernel is build
with USB gadget support.
Reported-By: NAndreas Faerber <afaerber@suse.de>
Signed-off-by: NSjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

In case the optional dr_mode property isn't set in the dwc3 nodes the
the controller will go into OTG mode if both USB host and USB gadget
functionality are enabled in the kernel configuration. Unfortunately
this results in USB not working on exynos5420-peach-pit and
exynos5800-peach-pi with such a kernel configuration unless manually
change the mode. To resolve that explicitly configure the dual role
mode as host.
Signed-off-by: NSjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: NAndreas Faerber <afaerber@suse.de>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The EIRSR and ELRSR registers are 32-bit registers on GICv2, and we
store these as an array of two such registers on the vgic vcpu struct.
However, we access them as a single 64-bit value or as a bitmap pointer
in the generic vgic code, which breaks BE support.

Instead, store them as u64 values on the vgic structure and do the
word-swapping in the assembly code, which already handles the byte order
for BE systems.
Tested-by: NVictor Kamensky <victor.kamensky@linaro.org>
Acked-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>

CM-QS600 is a APQ8064 based computer on module.
The details are available at
http://compulab.co.il/products/computer-on-modules/cm-qs600/Signed-off-by: NMike Rapoport <mike.rapoport@gmail.com>
Acked-by: NIgor Grinberg <grinberg@compulab.co.il>
Signed-off-by: NKumar Gala <galak@codeaurora.org>

This DTS has support for the Sony Xperia Z1 phone (codenamed Honami).
This first version of the DTS supports just a serial console.
Signed-off-by: NTim Bird <tim.bird@sonymobile.com>
Tested-by: NKevin Hilman <khilman@linaro.org>
Signed-off-by: NKumar Gala <galak@codeaurora.org>

Add SATA PHY and SATA AHCI controller nodes to device tree to enable
generic ahci support on the IPQ8064/AP148 board.
Signed-off-by: NKumar Gala <galak@codeaurora.org>

Commit:
b8865767 ARM: KVM: user_mem_abort: support stage 2 MMIO page mapping

introduced some code in user_mem_abort that failed to compile if
STRICT_MM_TYPECHECKS was enabled.

This patch fixes up the failing comparison.
Signed-off-by: NSteve Capper <steve.capper@linaro.org>
Reviewed-by: NKim Phillips <kim.phillips@linaro.org>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>

Commit 97a13e52 ('net: phy: mdio-sun4i: don't select REGULATOR') removed
the select of REGULATOR, which means that it now has to be explicitly
enabled in the defconfig or things won't work very well.

In particular, this fixes a problem with SD/MMC not probing on my A31-based
board.

Cc: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

When creating or moving a memslot, make sure the IPA space is within the
addressable range of the guest.  Otherwise, user space can create too
large a memslot and KVM would try to access potentially unallocated page
table entries when inserting entries in the Stage-2 page tables.
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Acked-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>

This patch adds the necessary support for all host kernel PGSIZE and
VA_SPACE configuration options for both EL2 and the Stage-2 page tables.

However, for 40bit and 42bit PARange systems, the architecture mandates
that VTCR_EL2.SL0 is maximum 1, resulting in fewer levels of stage-2
pagge tables than levels of host kernel page tables.  At the same time,
systems with a PARange > 42bit, we limit the IPA range by always setting
VTCR_EL2.T0SZ to 24.

To solve the situation with different levels of page tables for Stage-2
translation than the host kernel page tables, we allocate a dummy PGD
with pointers to our actual inital level Stage-2 page table, in order
for us to reuse the kernel pgtable manipulation primitives.  Reproducing
all these in KVM does not look pretty and unnecessarily complicates the
32-bit side.

Systems with a PARange < 40bits are not yet supported.

 [ I have reworked this patch from its original form submitted by
   Jungseok to take the architecture constraints into consideration.
   There were too many changes from the original patch for me to
   preserve the authorship.  Thanks to Catalin Marinas for his help in
   figuring out a good solution to this challenge.  I have also fixed
   various bugs and missing error code handling from the original
   patch. - Christoffer ]
Reviewed-by: NCatalin Marinas <catalin.marinas@arm.com>
Acked-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NJungseok Lee <jungseoklee85@gmail.com>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>

The kernel used to contain two functions for length-delimited,
case-insensitive string comparison, strnicmp with correct semantics and
a slightly buggy strncasecmp.  The latter is the POSIX name, so strnicmp
was renamed to strncasecmp, and strnicmp made into a wrapper for the new
strncasecmp to avoid breaking existing users.

To allow the compat wrapper strnicmp to be removed at some point in the
future, and to avoid the extra indirection cost, do
s/strnicmp/strncasecmp/g.
Signed-off-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix wrong compatible string of Exynos3250 RTC (Real-Time Clock) dt node.
The RTC of Exynos3250 must need additional source clock (XrtcXTI).
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

There is really no point in faulting in memory regions page by page
if they are not backed by demand paged system RAM but by a linear
passthrough mapping of a host MMIO region. So instead, detect such
regions at setup time and install the mappings for the backing all
at once.
Acked-by: NMarc Zyngier <marc.zyngier@arm.com>
Reviewed-by: NChristoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>

Now that we support read-only memslots, we need to make sure that
pass-through device mappings are not mapped writable if the guest
has requested them to be read-only. The existing implementation
already honours this by calling kvm_set_s2pte_writable() on the new
pte in case of writable mappings, so all we need to do is define
the default pgprot_t value used for devices to be PTE_S2_RDONLY.
Acked-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>

Add support for read-only MMIO passthrough mappings by adding a
'writable' parameter to kvm_phys_addr_ioremap. For the moment,
mappings will be read-write even if 'writable' is false, but once
the definition of PAGE_S2_DEVICE gets changed, those mappings will
be created read-only.
Acked-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>

Handle the potential NULL return value of find_vma_intersection()
before dereferencing it.
Acked-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>

Pass __GFP_ZERO to __get_free_pages() instead of calling memset()
explicitly.
Acked-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>