The mute-LED is controlled in patch_sigmatel.c by (ab-)using the
powersave hook.  This can be now rewritten with the vmaster hook
instead, which is much simpler and can work even without
CONFIG_SND_HDA_POWER_SAVE kconfig.

A drawback is that the mute-LED corresponds _only_ to the Master mixer
switch instead of checking the whole DACs.  But usually this shouldn't
be a big problem as PA enables the mixer elements accordingly.

Also, this patch changes the code to create vmaster always even on
STAC9200 and STAC925x.  The former "Master" on these chips are renamed
as "PCM" now.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

It'll be used for adding hooks in later patches.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This patch adds a hook to vmaster control to be called at each time
when the master value is changed.  It'd be handy for an additional
mute LED control following the Master switch, for example.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

When the driver is changed to use vmaster or a new slave element is
added by the improvement of the parser code, user may face often the
silent output because of the muted slave mixer although Master volume
is properly set.  And they complain.  And I get upset.

Although such a mixer element should be initialized via "alsactl init",
it'd be more user-friendly if the known output slaves are unmuted and
set to 0dB so that user can control the volume only with Master as
default.  Since Master is still set muted as default even with this
change, no risk of the speaker blow up, too.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

We've seen a problem with a pop-noise at suspend/resume on a HP
machine with ALC269, and it turned out to be an issue that the
controller going to D3 while the codec is unused.

When the device is once suspended and resumed and kept unused, the
driver doesn't initialize the codecs.  Instead, the codec chips are
set up dynamically at the first usage.  Now, suppose the device going
to suspend again before the codec is set up.  The controller is turned
off to D3 while the codec chips are untouched.  This caused a pop
noise because the codec chip might have been turned on implicitly by
the hardware.

As a workaround, the codec chip needs to be set to D3 when going to
suspend no matter whether it was used or not.  Also, for making it
happening, the controller has to be always set up in the resume path.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Move the currently unused spec->init_hook at the beginning of the init
sequence so that the recently added ALC269VB coef setup can be put
there.  The alc_init() is again clean without an ugly check.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Conflicts:
	sound/pci/hda/patch_realtek.c

The coef setup in alc269_fill_coef() was designed only for ALC269VB
model, and this has some bad effects for other ALC269 variants, such
as turning off the external mic input.  Apply it only to ALC269VB.
Signed-off-by: NKailang Yang <kailang@realtek.com>
Cc: <stable@kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Its BIOS suppresses the PC beep although it's implemented.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

My CD input got lost in commit 68ef0561.
Raymond helped me to add the necessary pin fixup to make it appear again. In
fact, this is basically his patch. It fixes alsa bug #5541.
Signed-off-by: NMarton Balint <cus@passwd.hu>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The recent addition of volume-knob widget in the auto-parser broke
automute/autoswitch for some Realtek devices.
Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

A driver specific fix that wasn't noticed as the OpenMoko guys have been
stuck on 2.6.39 for a very long time now and are just starting to catch
up again.

The neo1973 driver had wrong codec name which prevented the "sound card"
from appearing.
Signed-off-by: NDenis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org

Speaker-Out renames are merged.

Conflicts:
	sound/pci/hda/patch_realtek.c

Kill hyphens from "Line-Out" name strings, as suggested by Mark Brown.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

A small fix for the SSI driver and a fix for system shutdown with modern
devices.  Most of the modern devices will never get shut down normally
with a visible kernel log as the systems they're in tend not to shut
down often and when they do it's usually in form factors that don't have
a user visible console.

It seems that Lenovo machines (or codec chip itself?) leave the unsol
event tags and the enablement-flag from other pins bogusly even on the
unused pins.  Although this shouldn't be too critical, it's better to
clear them up sanely.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Some codecs don't supply the mute amp-capabilities although the lowest
volume gives the mute.  It'd be handy if the parser provides the mute
mixers in such a case.

This patch adds an extension amp-cap bit (which is used only in the
driver) to represent the min volume = mute state.  Also modified the
amp cache code to support the fake mute feature when this bit is set
but the real mute bit is unset.

In addition, conexant cx5051 parser uses this new feature to implement
the missing mute controls.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=42825

Cc: <stable@kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

A bug report with an old Sony laptop showed that we can't rely on BIOS
setting the pins of headphones but the driver should set always by
itself.

Cc: <stable@kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The docking-station of Thinkpad X200 & co supports also an SPDIF output,
and the corresponding pin 0x1c has to be enabled for using it.
Reported-and-tested-by: NSebastian Glita <sebastian.glita@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This patch adds a new position_fix option value, 4, as a combo mode
to use LPIB for playbacks and POSBUF for captures.  It's the way
recommended by Intel hardware guys.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Enables port E of IDT 92HD91 codec as output and sets correct output
phase between ports E and D and high pass filter.
Signed-off-by: NVitaliy Kulikov <Vitaliy.Kulikov@idt.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

opl3->private_data was set even if opl3 could not be created.
Signed-off-by: NAlban Bedel <albeu@free.fr>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

When there are multiple input sources, the driver wrongly overwrites with
the value of the last input source on other slots at resume.  Thus the
primary input source may be shown wrongly.
Reported-and-tested-by: NJulian Sikorski <belegdol@gmail.com>
Cc: <stable@kernel.org> [v3.1+]
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

According to i.MX27 Reference Manual (p 1593) TXBIT0 bit selects
whether the most significant or the less significant part of the
data word written to the FIFO is transmitted.

As DSP_A is the same as DSP_B with a data offset of 1 bit, it
doesn't make any sense to remove TXBIT0 bit here.
Signed-off-by: NJavier Martin <javier.martin@vista-silicon.com>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org

Recent enhancements in the bias management means that we might not be
in standby when the CODEC is idle and can have active widgets without
being in full power mode but the shutdown functionality assumes these
things. Add checks for the bias level at each stage so that we don't
do transitions other than the ON->PREPARE->STANDBY->OFF ones that the
drivers are expecting.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

[the order sorted by tiwai]
Signed-off-by: NWu Fengguang <fengguang.wu@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Added sanity checks in a few places not to assume the pins having the
certain amp caps or the input-source being always assigned to a mux.

No actual bugs have been triggered by these, but surely better to be a
bit more robust.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The driver may create duplicated mic boost controls when there are
multiple mics with the very same type / location, and this leads to
the error at actual kcontrol creation.  It needs to check the validity
of the created control and add a proper index if it's duplicated.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Commit 3702b082 added a lock, but did not account for the case of
SNDRV_PCM_POS_XRUN, which would get immediately overwritten.

This could be bundled into one if-else-if statement, but the goto
helps to clarify the 'exceptional' case.

Thanks to Andreas Pape for spotting this.
Signed-off-by: NMark Hills <mark@pogo.org.uk>
Acked-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

A couple of small, driver specific fixes - nothing too exciting going
on.

A few clean-ups for post-static-quirk time:
- Call alc_auto_init_std() statically in alc_init() instead of setting
  spec->init_hook in each caller.  spec->init_hook field is left
  unused for any future use.

- Move the call of set_capture_mixer() to to alc_parse_auto_config()
  instead of each caller.

- Get rid of the ADC-filling and imux check in each parser function.
  This is no longer needed since the auto-parser always check ADCs and
  imux.  It was only for the static quirks.

- Kill unused defines
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

When the machine has two speakers but wants to put more multi-io
jacks, the parser shouldn't consider about the shared DAC but try to
assign the individual DACs.  Otherwise the channel mapping would be
fairly confused and lead to the wrong DACs.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

When the multi-io is added to the two speaker output configuration,
the parser would try to add yet another "Bass Speaker" control since
it checks only cfg->line_outs.  Add a workaround for it by simply
passing the channel name in the case of multi-io outputs.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Even if the outputs are using shared DACs, we can still create individual
mute siwtches since they are assigned per pin.  This allows to create,
e.g. Speaker and Bass Speaker mute switches while the single volume is
used for these outputs.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

When BIOS is damn crazy and gives no pin-config at all, the driver might
lead to a NULL dereference.  Let's add a NULL check for such a case.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Similarly in patch_via.c, parse the active analog-loopback connections
and create a list dynamically rather than static arrays.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Resitance is futile.  The remaining static model quirks for Apple
machines with ALC882-compatible codecs are converted to the auto-parser
now.  We can remove all alc*_quirks.c finally.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Current ak4642 driver had wrong dapm settings for headphone L/R.
If you select headphone L, and select R after that,
headphone L setting was removed by R settings.

This patch fixes it up.
It provides just "Headphone Enable" to user side
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

If anyone wants to debug the driver and avoid the existing fix-ups,
pass model=nofixup option.  Then the driver will skip to pick up the
fixup list.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>