sdio_reset sends a CMD52 to reset the sdio card.  This is highly
recommended for sdio cards being reinitialized.  Since we do not
know if the card is being reinitialized we just send the command.
SD/eMMC cards are supposed to ignore the CMD before the CMD0.
Document why we are doing this.
Signed-off-by: NPhilip Rakity <prakity@marvell.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch adds DDR mode support to dw_mmc.

If we set any bit in UHS_REG bit[16:31], the card of that slot is
supported for DDR mode.  For example, if UHS_REG[16] is set, card
number 0 is DDR mode.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

drivers/mmc/host/via-sdmmc.c: In function ‘via_reset_pcictrl’:
drivers/mmc/host/via-sdmmc.c:805:8: warning: variable ‘addrbase’ set but
not used [-Wunused-but-set-variable]
Signed-off-by: NChris Ball <cjb@laptop.org>
Cc: Harald Welte <HaraldWelte@viatech.com>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>

Fixes:

drivers/mmc/host/cb710-mmc.c: In function ‘cb710_wait_while_busy’:
drivers/mmc/host/cb710-mmc.c:182:6: warning: variable ‘err’ set but not
used [-Wunused-but-set-variable]
Signed-off-by: NChris Ball <cjb@laptop.org>
Acked-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>

drivers/mmc/host/sdhci-pci.c: In function ‘sdhci_pci_probe_slot’:
drivers/mmc/host/sdhci-pci.c:913:18: warning: variable ‘addr’ set but
not used [-Wunused-but-set-variable]
Signed-off-by: NChris Ball <cjb@laptop.org>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>

This adds the mmc host driver for Freescale MXS-based SoC i.MX23/28.
The driver calls into mxs-dma via generic dmaengine api for both pio
and data transfer.

Thanks Chris Ball for the indentation patch.
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>
Reviewed-by: NArnd Bergmann <arnd@arndb.de>
Tested-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Acked-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NChris Ball <cjb@laptop.org>

This switches the mxcmmc driver to use the dmaengine API. Unlike
the old one this one is always present in the tree, even if no DMA
is implemented, hence we can remove all the #ifdefs in from the driver.
The driver automatically switches to PIO mode if no DMA support or no
suitable channel is available.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch adds support for 8-bit buswidth.
dw_mmc can use 8-bit buswidth and set to CTYPE_8BIT in card-type register.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

If we need some quirks, maybe add quirks in future
But now, quirks value set to integer..later we should be confused..
So I think that need bit-shift control.

And If we need not any quirks, we didn't set anything..
(Need not DW_MCI_QUIRK_NONE)
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Use the new dmaengine helper functions, and drop the error check
on the returned cookier from the dmaengine - we recently
established that this is really not allowed to fail.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

This variable doesn't seem to be used for anything after the
other patches so just drop it.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

According to the DMA-API you shall unmap the sglists with the same
sglist length as passed into the mapping function, not the
returned value from the mapping function.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

As established for the MMCI, it is proper to map the DMA buffers
on the DMA engine which is the one actually performing the DMA.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Use the new dmaengine helper functions, and drop the error check
on the returned cookier from the dmaengine - we recently
established that this is really not allowed to fail.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

The host_sglen is now actually used to keep track of whether DMA
is active or not, so rename and retype it to bool.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

According to the DMA-API you shall unmap the sglists with the same
sglist length as passed into the mapping function, not the
returned value from the mapping function.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

As established for the MMCI, it is proper to map the DMA buffers
on the DMA engine which is the one actually performing the DMA.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Use the new dmaengine helpers to make the code more readable.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Fixes the following:
- It is perfectly legal for the dma_map_sg() to return fewer
  entries than were passed in.
- Supply the returned numer of (possibly coalesced) entries to
  the device_pre_slave_sg() function.
- Use the proper original sg_len when unmapping the sglist
  in the error path.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

As established for the MMCI, it is proper to map the DMA buffers
on the DMA engine which is the one actually performing the DMA.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Signed-off-by: NManoj Iyer <manoj.iyer@canonical.com>
Cc: <stable@kernel.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

So we know the implementation and prototypes agree with each other.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: NChris Ball <cjb@laptop.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

The test file is created under debugfs, not sysfs. Also remove
the unnecessary default n.
Signed-off-by: NWill Newton <will.newton@imgtec.com>
Reviewed-by: NChris Ball <cjb@laptop.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Setting this bit in the clock enable register will stop the clock
when the card is in the IDLE state.
Signed-off-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

We need to run the card detect tasklet at the end of slot initialisation
as it is possible that a card has been inserted prior to boot, so we don't
see an insertion interrupt and now the card is sitting there inserted but
with no power to it.
Signed-off-by: NNeil Jones <neil.jones@imgtec.com>
Signed-off-by: NWill Newton <will.newton@imgtec.com>
Reviewed-by: NMatt Fleming <matt@console-pimps.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Currently MMC_MXC driver can be selected by all i.MX devices.

Restrict its use only for the appropriate processors.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

Reviewed-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NChris Ball <cjb@laptop.org>

Add two large sequential I/O performance tests:
        35. Large sequential read into scattered pages
        36. Large sequential write from scattered pages

The tests measure transfer times for 10MiB, 100MiB, 1000MiB.
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Existing performance tests measure single or sequential I/O speed.
Add two random I/O tests:
        33. Random read performance by transfer size
        34. Random write performance by transfer size
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

The test area size was set to the preferred erase size but for comparison
purposes it is better if it is the same size for different devices.  Make
it a multiple of preferred erase size that is greater than or equal to 4MiB.
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

This sdio card supports having its sdio clock shutdown.
It is also not using the SDIO IRQ, but rather uses a side gpio irq.
Signed-off-by: NPierre Tardy <tardyp@gmail.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Some sdio card are not following sdio standard, and do not work
when the sdio bus's clock is gated.

To keep functionnality for all legacy driver, we turn this quirk on
for every sdio card.
Drivers needs to disable the quirk manually when someone verifies that
their supported card works with clock gating.
Signed-off-by: NPierre Tardy <tardyp@gmail.com>
Acked-by: NOhad Ben-Cohen <ohad@wizery.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Some cards have quirks valid for every platforms using current
platform quirk hooks leads to a lot of code and debug duplication.

So we inspire a bit from what exists in PCI subsystem and do our own
per vendorid/deviceid quirk.  We still drop the complexity of the pci
quirk system (with special section tables, and so on).
That can be added later if needed.
Signed-off-by: NPierre Tardy <pierre.tardy@intel.com>
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>
Acked-by: NOhad Ben-Cohen <ohad@wizery.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Since mmc clock gating can also be used as a power gating
tip, it's better to put the led blinking after having
ungated the clock.
Signed-off-by: NPierre Tardy <pierre.tardy@intel.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

If the MMC host controller does not support waiting for card signaling
busy state (MMC_CAP_WAIT_WHILE_BUSY cap), there is no point in prining
the relevant warning message.
Signed-off-by: NPawel Moll <pawel.moll@arm.com>
Reviewed-by: NMatt Fleming <matt@console-pimps.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Samsung SDHCI host controller supports the Auto CMD12.
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

While the MMC handled the card's read only flag correctly on open,
it did not setup the flag in the allocated disk structure. The
consequence being that probing the /sys/class/block/mmcblkX/ro
attribute always reported 0.
Signed-off-by: NMarc-Andre Hebert <hebert.marcandre@gmail.com>
Reviewed-by: NChris Ball <cjb@laptop.org>
Tested-by: NChris Ball <cjb@laptop.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Enhanced area feature is a new feature defined in eMMC4.4 standard. This
user data area provides higher performance/reliability, at the expense
of using twice the effective media space due to the area using SLC.

The MMC driver now reads out the enhanced area offset and size and adds
them to the device attributes in sysfs. Enabling the enhanced area can
only be done once, and should be done in manufacturing. To use this
feature, bit ERASE_GRP_DEF should also be set.

Documentation/ABI/testing/sysfs-devices-mmc describes the two new
attributes.
Signed-off-by: NChuanxiao Dong <chuanxiao.dong@intel.com>
Reviewed-by: NChris Ball <cjb@laptop.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
  [CPUFREQ] pcc-cpufreq: don't load driver if get_freq fails during init.