Skip to content

cloud-kernel
cloud-kernel

openanolis / cloud-kernel
1 年多 前同步成功

通知 160
Star 36
Fork 7
cloud-kernel
cloud-kernel
切换分支/标签
  1. 23 8月, 2009 2 次提交
  3. 22 6月, 2009 1 次提交
  5. 09 6月, 2009 3 次提交
  7. 30 5月, 2009 1 次提交
    • J
      net: convert unicast addr list · ccffad25
      由 Jiri Pirko 提交于 
      This patch converts unicast address list to standard list_head using
previously introduced struct netdev_hw_addr. It also relaxes the
locking. Original spinlock (still used for multicast addresses) is not
needed and is no longer used for a protection of this list. All
reading and writing takes place under rtnl (with no changes).

I also removed a possibility to specify the length of the address
while adding or deleting unicast address. It's always dev->addr_len.

The convertion touched especially e1000 and ixgbe codes when the
change is not so trivial.
Signed-off-by: NJiri Pirko <jpirko@redhat.com>

 drivers/net/bnx2.c               |   13 +--
 drivers/net/e1000/e1000_main.c   |   24 +++--
 drivers/net/ixgbe/ixgbe_common.c |   14 ++--
 drivers/net/ixgbe/ixgbe_common.h |    4 +-
 drivers/net/ixgbe/ixgbe_main.c   |    6 +-
 drivers/net/ixgbe/ixgbe_type.h   |    4 +-
 drivers/net/macvlan.c            |   11 +-
 drivers/net/mv643xx_eth.c        |   11 +-
 drivers/net/niu.c                |    7 +-
 drivers/net/virtio_net.c         |    7 +-
 drivers/s390/net/qeth_l2_main.c  |    6 +-
 drivers/scsi/fcoe/fcoe.c         |   16 ++--
 include/linux/netdevice.h        |   18 ++--
 net/8021q/vlan.c                 |    4 +-
 net/8021q/vlan_dev.c             |   10 +-
 net/core/dev.c                   |  195 +++++++++++++++++++++++++++-----------
 net/dsa/slave.c                  |   10 +-
 net/packet/af_packet.c           |    4 +-
 18 files changed, 227 insertions(+), 137 deletions(-)
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      ccffad25
  9. 24 5月, 2009 1 次提交
  11. 21 5月, 2009 1 次提交
  13. 18 5月, 2009 2 次提交
    • V
      fcoe: adds spma mode support · 184dd345
      由 Vasu Dev 提交于 
      If we can find a type NETDEV_HW_ADDR_T_SAN mac address from the
corresponding netdev for a fcoe interface then sets up added the
fc->ctlr.spma flag and stores spma mode address in ctl_src_addr.

In case the spma flag is set then:-

 1. Adds spma mode MAC address in ctl_src_addr as secondary
    MAC address, the FLOGI for FIP and pre-FIP will go out
    using this address.
 2. Cleans up stored spma MAC address in ctl_src_addr in
    fcoe_netdev_cleanup.
 3. Sets up spma bit in fip_flags for FIP solicitations along
    with exiting FPMA bit setting.
 4. Initialize the FLOGI FIP MAC descriptor to stored spma
    MAC address in ctl_src_addr. This is used as proposed
    FCoE MAC address from initiator along with both SPMA
    and FPMA bit set in FIP solicitation, in response the
    switch may grant any FPMA or SPMA mode MAC address to
    initiator.

Removes FIP descriptor type checking against ELS type
ELS_FLOGI in fcoe_ctlr_encaps to update a FIP MAC descriptor,
instead now checks against FIP_DT_FLOGI.

I've tested this with available FPMA-only FCoE switch but
since data_src_addr is updated using same old code for
both FPMA and SPMA modes with FIP or pre-FIP links, so added
SPMA mode will work with SPMA-only switch also provided that
switch grants a valid MAC address.
Signed-off-by: NVasu Dev <vasu.dev@intel.com>
Signed-off-by: NYi Zou <yi.zou@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      184dd345
    • V
      fcoe: consolidates netdev related config and cleanup for spma mode · ab6b85c1
      由 Vasu Dev 提交于 
      Currently fcoe_netdev_config adds netdev pkt handler for fcoe pkts,
fcoe_if_create adds netdev pkt handler for fip packets, a secondary
MAC address is added by fcoe_netdev_config and then later cleanup
for these netdev related config/adds is done only during
fcoe_if_destroy and no cleanup done on error during fcoe interface
creation after above netdev config calling in fcoe_if_create.

So this patch adds single func for above mentioned cleanup the
fcoe_netdev_cleanup and then calls this func on either fcoe interface
destroy or exiting from fcoe_if_create due to an error after fcoe/fip
related above netdev config is done.

Moved netdev pkt handler addition code blocks for fip pkts close to
similar code block for foce pkt in fcoe_netdev_config, so that added
fcoe_netdev_cleanup could be called on error from fcoe_netdev_config
to undo these both additions for fcoe/fip pkt handlers. This move
required reference to fcoe_fip_recv in fcoe_netdev_config, so moved
fip related functions fcoe_fip_recv, fcoe_fip_send and
fcoe_update_src_mac above fcoe_netdev_config.

This consolidation will enable spma mode support in next patch to
easily add or delete spma mode mac address beside fixing current
no cleanup issue during error.
Signed-off-by: NVasu Dev <vasu.dev@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      ab6b85c1
  15. 27 4月, 2009 4 次提交
  17. 03 4月, 2009 12 次提交
  19. 14 3月, 2009 3 次提交
  21. 10 3月, 2009 8 次提交
  23. 07 3月, 2009 1 次提交
    • V
      [SCSI] libfc, fcoe: fixed locking issues with lport->lp_mutex around lport->link_status · bc0e17f6
      由 Vasu Dev 提交于 
      The fcoe_xmit could call fc_pause in case the pending skb queue len is larger
than FCOE_MAX_QUEUE_DEPTH, the fc_pause was trying to grab lport->lp_muex to
change lport->link_status and that had these issues :-

1. The fcoe_xmit was getting called with bh disabled, thus causing
"BUG: scheduling while atomic" when grabbing lport->lp_muex with bh disabled.

2. fc_linkup and fc_linkdown function calls lport_enter function with
lport->lp_mutex held and these enter function in turn calls fcoe_xmit to send
lport related FC frame, e.g. fc_linkup => fc_lport_enter_flogi to send flogi
req. In this case grabbing the same lport->lp_mutex again in fc_puase from
fcoe_xmit would cause deadlock.

The lport->lp_mutex was used for setting FC_PAUSE in fcoe_xmit path but
FC_PAUSE bit was not used anywhere beside just setting and clear this
bit in lport->link_status, instead used a separate field qfull in fc_lport
to eliminate need for lport->lp_mutex to track pending queue full condition
and in turn avoid above described two locking issues.

Also added check for lp->qfull in fc_fcp_lport_queue_ready to trigger
SCSI_MLQUEUE_HOST_BUSY when lp->qfull is set to prevent more scsi-ml cmds
while lp->qfull is set.

This patch eliminated FC_LINK_UP and FC_PAUSE and instead used dedicated
fields in fc_lport for this, this simplified all related conditional
code.

Also removed fc_pause and fc_unpause functions and instead used newly added
lport->qfull directly in fcoe.
Signed-off-by: NVasu Dev <vasu.dev@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
      bc0e17f6
  25. 31 12月, 2008 1 次提交