The transfer burst count (TBC) field in the Isoc TRB does not fit the new
larger burst count available for USB 3.1 SSP Isoc tranfers.
xhci 1.1 solved this by reusing the TD size field for transfer burst count.
The Mult field was outgrown as well. xhci 1.1  controllers can calculate
Mult itself and is not set if the new layout is used.

xhci 1.1 controllers that support the new Isoc TRB format expose a
Extended TBC Capability (ETC). To take the new format into use the xhci
host controller driver needs to set a Extended TBC Enable (ETE) bit.
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Clean up xhci_queue_isoc_tx() and helpers to prepare them for USB 3.1 and
xhci 1.1 isoc TRB changes.

Only functional change is adding xhci version 1.1 to the BEI flag check
toghether with xhci version 1.0. Both versions behave the same.
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

SuperSpeedPlus doubled the number of transactions per service interval
the isoc endpoints supports.

To support this, xhci 1.1 added Large ESIT Capability (LEC), which
takes into use new bits in the endpoint context to fit the parameters.

If xhci supports LEC, and the device has a SuperSpeedPlus Isoc companion
descriptor then take into use the high bits of max esit payload, and
skip calculating the Mult field as it wouldn't fit. LEC capable
host will calculate the Mult based on other paramenters.
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

xhci_endpoint_init() and helper functions were a bit messy.
Adding the higher bandwidth SuperSpeedPlus Isoc support on
top of it would make it even harder to read.

No functional changes.
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

USB 3.1 devices that support precision time measurement have an
additional PTM cabaility descriptor as part of the full BOS descriptor

Look for this descriptor while parsing the BOS descriptor, and store it in
struct usb_hub_bos if it exists.
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

USB 3.1 devices can return a new SuperSpeedPlus isoc endpoint companion
descriptor for a isochronous endpoint that requires more than 48K bytes
per Service Interval.

The new descriptor immediately follows the old USB 3.0 SuperSpeed Endpoint
Companion and will provide a new BytesPerInterval value.

It is parsed and stored in struct usb_host_endpoint with the other endpoint
related descriptors, and should be used by USB3.1 capable hosts to reserve
bus time in the schedule.
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix the RC QPs send queue overhead computation to take into account
two additional segments in the WQE which are needed for registration
operations.

The ATOMIC and UMR segments can't coexist together, so chose maximum out
of them.

The commit 9e65dc37 ("IB/mlx5: Fix RC transport send queue overhead
computation") was intended to update RC transport as commit messages
states, but added the code to UC transport.

Fixes: 9e65dc37 ("IB/mlx5: Fix RC transport send queue overhead computation")
Signed-off-by: NKamal Heib <kamalh@mellanox.com>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Reviewed-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

A narrow window for race condition still exist between
multicast join thread and *dev_flush workers.
A kernel crash caused by prolong erratic link state changes
was observed (most likely a faulty cabling):

[167275.656270] BUG: unable to handle kernel NULL pointer dereference at
0000000000000020
[167275.665973] IP: [<ffffffffa05f8f2e>] ipoib_mcast_join+0xae/0x1d0 [ib_ipoib]
[167275.674443] PGD 0
[167275.677373] Oops: 0000 [#1] SMP
...
[167275.977530] Call Trace:
[167275.982225]  [<ffffffffa05f92f0>] ? ipoib_mcast_free+0x200/0x200 [ib_ipoib]
[167275.992024]  [<ffffffffa05fa1b7>] ipoib_mcast_join_task+0x2a7/0x490
[ib_ipoib]
[167276.002149]  [<ffffffff8109d5fb>] process_one_work+0x17b/0x470
[167276.010754]  [<ffffffff8109e3cb>] worker_thread+0x11b/0x400
[167276.019088]  [<ffffffff8109e2b0>] ? rescuer_thread+0x400/0x400
[167276.027737]  [<ffffffff810a5aef>] kthread+0xcf/0xe0
Here was a hit spot:
ipoib_mcast_join() {
..............
      rec.qkey      = priv->broadcast->mcmember.qkey;
                                       ^^^^^^^
.....
 }
Proposed patch should prevent multicast join task to continue
if link state change is detected.
Signed-off-by: NAlex Estrin <alex.estrin@intel.com>

Changes from v4:
- as suggested by Doug Ledford, optimized spinlock usage,
i.e. ipoib_mcast_join() is called with lock held.
Changes from v3:
- sync with priv->lock before flag check.
Chages from v2:
- Move check for OPER_UP flag state to mcast_join() to
ensure no event worker is in progress.
- minor style fixes.
Changes from v1:
- No need to lock again if error detected.
Signed-off-by: NDoug Ledford <dledford@redhat.com>

When checking specific attribute from a bit mask, need to use bitwise
AND and not logical AND, fixed that.

Fixes: 145d9c54 ('IB/core: Display extended counter set if
available')
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: NChristoph Lameter <cl@linux.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The while loop after err_slaves should use post-decrement; otherwise
we'll fail to do the kfrees for i==0, and will run into out-of-bounds
accesses if the setup above failed already at i==0.

[I'm not sure why one even bothers populating the ->vlan_filter array:
mlx4.h isn't #included by anything outside
drivers/net/ethernet/mellanox/mlx4/, and "git grep -C2 -w vlan_filter
drivers/net/ethernet/mellanox/mlx4/" seems to suggest that the
vlan_filter elements aren't used at all.]
Signed-off-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

This reverts commit 829b6962.

Revert this change as it causes a sysfs path to change and therefore
introduces and ABI regression. More precisely Android's vold is not being
able to access /sys/module/mmcblk/parameters/perdev_minors any more, since
the path becomes changed to: "/sys/module/mmc_block/..."

Fixes: 829b6962 ("mmc: block: don't use parameter prefix if built as
module")
Reported-by: NJohn Stultz <john.stultz@linaro.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

In __cpufreq_cooling_register() we allocate the arrays for time_in_idle
and time_in_idle_timestamp to be as big as the number of cpus in this
cpufreq device.  However, in get_load() we access this array using the
cpu number as index, which can result in an out of bound access.

Index time_in_idle{,_timestamp} using the index in the cpufreq_device's
allowed_cpus mask, as we do for the load_cpu array in
cpufreq_get_requested_power()
Reported-by: NNicolas Boichat <drinkcat@chromium.org>
Cc: Amit Daniel Kachhap <amit.kachhap@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Tested-by: NNicolas Boichat <drinkcat@chromium.org>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NJavi Merino <javi.merino@arm.com>
Signed-off-by: NEduardo Valentin <edubezval@gmail.com>

Intel BXT/APL use a card detect GPIO however the host controller
will not enable bus power unless it's card detect also reflects
the presence of a card.  Unfortunately those 2 things race which
can result in commands not starting, after which the controller
does nothing and there is a 10 second wait for the driver's
10-second timer to timeout.

That is fixed by having the driver look also at the present state
register to determine if the card is present.  Consequently, provide
a 'get_cd' mmc host operation for BXT/APL that does that.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Intel BXT/APL use a card detect GPIO however the host controller
will not enable bus power unless it's card detect also reflects
the presence of a card.  Unfortunately those 2 things race which
can result in commands not starting, after which the controller
does nothing and there is a 10 second wait for the driver's
10-second timer to timeout.

That is fixed by having the driver look also at the present state
register to determine if the card is present.  Consequently, provide
a 'get_cd' mmc host operation for BXT/APL that does that.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Drivers may need to provide their own get_cd() mmc host op, but
currently the internals of the current op (sdhci_get_cd()) are
provided by sdhci_do_get_cd() which is also called from
sdhci_request().

To allow override of the get_cd functionality, change sdhci_request()
to call ->get_cd() instead of sdhci_do_get_cd().

Note, in the future the call to ->get_cd() will likely be removed
from sdhci_request() since most drivers don't need actually it.
However this change is being done now to facilitate a subsequent
bug fix.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

In the past, fixes for specific hardware devices were implemented
in sdhci using quirks.  That approach is no longer accepted because
the growing number of quirks was starting to make the code difficult
to understand and maintain.

One alternative to quirks, is to allow drivers to override the default
mmc host operations.  This patch makes it easy to do that, and it is
needed for a subsequent bug fix, for which separate patches are
provided.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

EOImode1 is only used for the root controller and hence only the root
controller uses the eoimode1 functions for handling interrupts. However,
if the root controller supports EOImode1, then the EOImodeNS bit will be
set for all GICs, enabling EOImode1. This is not what we want and this
causes interrupts on non-root GICs to only be dropped in priority but
never deactivated. Therefore, only set the EOImodeNS bit for the root
controller.
Acked-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NJon Hunter <jonathanh@nvidia.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

Setting the affinity of an IRQ, it only applicable for the root
interrupt controller and so only populate this operator for the root
controller.
Acked-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NJon Hunter <jonathanh@nvidia.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

Calling component_add() may result in the completion of a set of
devices, which will try to bring up a master. In bringing the master
up, we populate its match array with the current set of children.

If binding any of the devices fails, component_add() itself will fail,
free the struct component entry, and return to the caller. The
now-freed entry is never removed from the master's match array, and
will later be used in a futile attempt to bind to freed memory.

Bring component_add's behaviour on failure to bring up a master into
line with component_del by removing the (to-be-freed) component from
the master's match array.

The specific case which broke was:
  - rockchip_drm_drv adds a component master
  - dwhdmi_rockchip adds a child component in probe (master incomplete)
  - rockchip_drm_vop adds two children in probe, which completes the
    set
  - inside component_add, we try to bring up the master, having
    populated the master's match array, and fail with EPROBE_DEFER from
    dwhdmi_rockchip; we delete the putative component
  - rockchip_drm_vop's probe fails and returns EPROBE_DEFER
  - we later re-probe rockchip_drm_vop and add the component; the
    master is complete, so we attempt to bring it up again
  - walking the match array, we find the previous child, whose master
    pointer doesn't match (as it has been freed in the meantime)
  - rockchip_drm_vop probe fails, and will never be attempted again

Fixes: ffc30b74Signed-off-by: NDaniel Stone <daniels@collabora.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NQuinn Tran <quinn.tran@qlogic.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NBart Van Assche <bart.vanassche@sandisk.com>
Fixes: fb3269ba ("qla2xxx: Add selective command queuing")
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Signed-off-by: NQuinn Tran <quinn.tran@qlogic.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NBart Van Assche <bart.vanassche@sandisk.com>
Fixes: fb3269ba ("qla2xxx: Add selective command queuing")
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch fixes an incorrect return of zero from the new
unmap_zeroes_data_store() configfs store attribute handler
introduced in v4.5-rc1, to use the correct 'count' bytes
return value.
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Otherwise we could try to evict overlapping userptr BOs in get_user_pages(),
leading to a possible circular locking dependency.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

An arbitrary amount of time can pass between spin_unlock and
radeon_fence_wait_any, so we need to ensure that nobody frees the
fences from under us.

Based on the analogous fix for amdgpu.
Signed-off-by: NNicolai Hähnle <nicolai.haehnle@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org

Signed-off-by: NNicolai Hähnle <nicolai.haehnle@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org

An arbitrary amount of time can pass between spin_unlock and
fence_wait_any_timeout, so we need to ensure that nobody frees the
fences from under us.

A stress test (rapidly starting and killing hundreds of glxgears
instances) ran into a deadlock in fence_wait_any_timeout after
about an hour, and this race condition appears to be a plausible
cause.

v2: agd: rebase on upstream
Signed-off-by: NNicolai Hähnle <nicolai.haehnle@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org

No need to re-init asic if it's already been initialized.
Skip IB tests since kernel processes are frozen in thaw.
Signed-off-by: NFlora Cui <Flora.Cui@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Adding Intel codename DNV platform device IDs for SATA.
Signed-off-by: NAlexandra Yates <alexandra.yates@linux.intel.com>
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org

Commit 27cbd7e8 ("mmc: sh_mmcif: rework dma channel handling")
introduced a typo causing the TX DMA channel allocation to be overwritten
by the requested RX DMA channel.

Fixes: 27cbd7e8 ("mmc: sh_mmcif: rework dma channel handling")
Signed-off-by: NChris Paterson <chris.paterson2@renesas.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Prior to 4.3, openvswitch tunnel vports (vxlan, gre and geneve) could
transmit vxlan packets of any size, constrained only by the ability to
send out the resulting packets.  4.3 introduced netdevs corresponding
to tunnel vports.  These netdevs have an MTU, which limits the size of
a packet that can be successfully encapsulated.  The default MTU
values are low (1500 or less), which is awkwardly small in the context
of physical networks supporting jumbo frames, and leads to a
conspicuous change in behaviour for userspace.

Instead, set the MTU on openvswitch-created netdevs to be the relevant
maximum (i.e. the maximum IP packet size minus any relevant overhead),
effectively restoring the behaviour prior to 4.3.
Signed-off-by: NDavid Wragg <david@weave.works>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow the MTU of geneve devices to be set to large values, in order to
exploit underlying networks with larger frame sizes.

GENEVE does not have a fixed encapsulation overhead (an openvswitch
rule can add variable length options), so there is no relevant maximum
MTU to enforce.  A maximum of IP_MAX_MTU is used instead.
Encapsulated packets that are too big for the underlying network will
get dropped on the floor.
Signed-off-by: NDavid Wragg <david@weave.works>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow the MTU of vxlan devices without an underlying device to be set
to larger values (up to a maximum based on IP packet limits and vxlan
overhead).

Previously, their MTUs could not be set to higher than the
conventional ethernet value of 1500.  This is a very arbitrary value
in the context of vxlan, and prevented vxlan devices from being able
to take advantage of jumbo frames etc.

The default MTU remains 1500, for compatibility.
Signed-off-by: NDavid Wragg <david@weave.works>
Acked-by: NRoopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver only needs to allocate for [ngpio / 32] controllers,
as each controller handles 32 gpios. But the current driver
allocates for ngpio of which the extra allocated are unused.
Fix it be registering only the required number of controllers.
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: NKeerthy <j-keerthy@ti.com>
Reviewed-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Currently the first parameter of irq_domain_add_legacy is NULL.
irq_find_host function returns NULL when we do not populate the of_node
and hence irq_of_parse_and_map call fails whenever we want to request a
gpio irq. This fixes the request_irq failures for gpio interrupts.
Signed-off-by: NKeerthy <j-keerthy@ti.com>
Reviewed-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This used to return -EFAULT, but the function above returns -EINVAL on
the same condition so let's stick to that.

The removal of error return on this path was introduced with b093410c
('mmc: block: copy resp[] data on err for MMC_IOC_MULTI_CMD').

Fixes: b093410c ('mmc: block: copy resp[] data on err for MMC_IOC_MULTI_CMD').
Signed-off-by: NOlof Johansson <olof@lixom.net>
Cc: Grant Grundler <grundler@google.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

If we reload phy-twl4030-usb, we get a warning about unbalanced
pm_runtime_enable. Let's fix the issue and also fix idling of the
device on unload before we attempt to shut it down.

If we don't properly idle the PHY before shutting it down on removal,
the twl4030 ends up consuming about 62mW of extra power compared to
running idle with the module loaded.

Cc: stable@vger.kernel.org
Cc: Bin Liu <b-liu@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: NeilBrown <neil@brown.name>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>

Otherwise rmmod omap2430; rmmod phy-twl4030-usb; modprobe omap2430
will try to use a non-existing phy and oops:

Unable to handle kernel paging request at virtual address b6f7c1f0
...
[<c048a284>] (devm_usb_get_phy_by_node) from [<bf0758ac>]
(omap2430_musb_init+0x44/0x2b4 [omap2430])
[<bf0758ac>] (omap2430_musb_init [omap2430]) from [<bf055ec0>]
(musb_init_controller+0x194/0x878 [musb_hdrc])

Cc: stable@vger.kernel.org
Cc: Bin Liu <b-liu@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: NeilBrown <neil@brown.name>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>

If phy_pm_runtime_get_sync failed but we already
enable regulator, current code return directly without
doing regulator_disable. This patch fix this problem
and cleanup err handle of phy_power_on to be more readable.

Fixes: 3be88125 ("phy: core: Support regulator ...")
Cc: <stable@vger.kernel.org> # v3.18+
Cc: Roger Quadros <rogerq@ti.com>
Cc: Axel Lin <axel.lin@ingics.com>
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>

fixing the error reported by script checkpatch.pl
static variables blinkenlights and old_scheme_first
were initialised to 0, correcting it.
Signed-off-by: NSaurabh Sengar <saurabh.truth@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/input/touchscreen/colibri-vf50-ts.c: In function ‘vf50_ts_probe’:
drivers/input/touchscreen/colibri-vf50-ts.c:302: error: implicit declaration of function ‘of_property_read_u32’
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>