Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- Use new routing input defines in em28xx-cards.c
- Fix S-Video settings for tvp5150-based cards (input was copied from saa7115
  based cards and worked only because S-Video was selected in the default: case)
- Replace VIDIOC_S_INPUT by VIDIOC_INT_S_VIDEO_ROUTING in em28xx-video.c
- Remove the now obsolete VIDIOC_S_INPUT handler in saa7115.c
- Add VIDIOC_INT_G/S_VIDEO_ROUTING in tvp5150.c
- Add new media/tvp5150.h with the routing defines.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Some saa7115-based cards use a different crystal frequency and a different
audio clock generation. Add a new VIDIOC_INT_S_CRYSTAL_FREQ command to be
able to set these values.
Also change the default APLL setting to 0. It makes no sense to have the
audio clock independent from the video clock, this can lead to audio/video
synchronization problems. Setting this to 0 is also consistent with the old
saa7114.c source and the way the Hauppauge Windows driver sets it.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- improve handling of the EXTERN input: don't start an unnecessary carrier scan
- improve the LOG_STATUS output
- ensure that a carrier scan is started again when switching back to the tuner.
- set correct prescale for L-NICAM
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

There is some old code in the or51133 firmware loading function that
has no effect.  Left a comment to in case it helps someone trying
to reverse engineer the chip.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Move <linux/usb_input.h> to <linux/usb/input.h> and remove some
redundant includes.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Various drivers use xmit_lock internally to synchronise with their
transmission routines.  They do so without setting xmit_lock_owner.
This is fine as long as netpoll is not in use.

With netpoll it is possible for deadlocks to occur if xmit_lock_owner
isn't set.  This is because if a printk occurs while xmit_lock is held
and xmit_lock_owner is not set can cause netpoll to attempt to take
xmit_lock recursively.

While it is possible to resolve this by getting netpoll to use
trylock, it is suboptimal because netpoll's sole objective is to
maximise the chance of getting the printk out on the wire.  So
delaying or dropping the message is to be avoided as much as possible.

So the only alternative is to always set xmit_lock_owner.  The
following patch does this by introducing the netif_tx_lock family of
functions that take care of setting/unsetting xmit_lock_owner.

I renamed xmit_lock to _xmit_lock to indicate that it should not be
used directly.  I didn't provide irq versions of the netif_tx_lock
functions since xmit_lock is meant to be a BH-disabling lock.

This is pretty much a straight text substitution except for a small
bug fix in winbond.  It currently uses
netif_stop_queue/spin_unlock_wait to stop transmission.  This is
unsafe as an IRQ can potentially wake up the queue.  So it is safer to
use netif_tx_disable.

The hamradio bits used spin_lock_irq but it is unnecessary as
xmit_lock must never be taken in an IRQ handler.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Mixing "depends on I2C" and "select I2C" within the media subsystem
leads to the following problem:
Warning! Found recursive dependency: I2C DVB_BUDGET DVB_BUDGET_PATCH
DVB_AV7110 VIDEO_SAA7146_VV VIDEO_SAA7146 I2C
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NManu Abraham <manu@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Those functions don't exist on PPC64 architecture.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

reference to .init.text: from .text between 'dvb_bt8xx_probe'
(at offset 0x122c) and 'dvb_bt8xx_remove'
reference to .init.text: from .text between 'dvb_bt8xx_probe'
(at offset 0x1267) and 'dvb_bt8xx_remove'
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Ref: Bugzilla 6179, 6589
Signed-off-by: NManu Abraham <manu@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

If CONFIG_VIDEO_DEV=m and CONFIG_VIDEO_V4L1_COMPAT=y, v4l1-compat should
be built as a module (currently, it isn't built at all leading to
problems with modules using it).
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

CONFIG_VIDEO_VIVI depends on CONFIG_VIDEO_BUF.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This patch fixes two off-by-one errors spotted by the Coverity checker.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

drivers/media/video/vivi.c: In function `vivi_map_sg':
drivers/media/video/vivi.c:799: error: `DMA_NONE' undeclared (first use in this function)
drivers/media/video/vivi.c:799: error: (Each undeclared identifier is reported only once
drivers/media/video/vivi.c:799: error: for each function it appears in.)
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Frequency range values in the current driver for the LG TDVS H06xF tuners
appear to have been a transposing of the 5 in the mid range 160-455 instead
of 165-450.
This patch corrects the pll programming for these tuners as per the datasheet.
Signed-off-by: NRusty Scott <rustys@ieee.org>
Signed-off-by: NMac Michaels <wmichaels1@earthlink.net>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

There is a missing break in card initialization function. Might screw
up initialization of Terratec Cinergy 400 TV.
Signed-off-by: NMikhail Gusarov <dottedmag@dottedmag.net>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The fast firmware load hack in cx25840 uses private data. In fact, it
breaks pvrusb2 and doesn't work at all with ivtv. It is a unsafe
implementation and so it is removed.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This patch prevents a bug where the frontend is unable to tune after waking
from powered down state. Now, the device remains powered on until it is
disconnected, just like the windows driver. It seems that the bluebird
firmware is unable to successfully handle tuning after a powered down state.
This patch fixes all of the FusionHDTV Bluebird USB2 devices. The Medion
MD95700 will still behave as before, since it was unaffected by this bug.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

*) Allow forcing the bandselect value with a module parameter to 
facilitate determining the correct bandselect frequencies.
*) Changes the bandselect frequency thresholds based on experiments 
with the above parameter in conjunction with the values in the spec.

Signed-off-by: Yeasah Pell <yeasah at schwide.net>
Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

*) Sets an additional tuner parameter (demodulator sample gain) that 
wasn't being set before.
*) Removes the low symbol rate tuner parameter tweaks in the previous 
patch -- it appears those tweaks are not necessary with the demodulator 
sample gain set correctly.
*) Cleanup and document the demodulator register initialization sequence.
*) Change set_fec routine to disable FEC auto scan when a specific code 
rate is selected.
*) Remove error message when reported FEC is invalid (which happens 
sometimes when the card has no signal)

Signed-off-by: Yeasah Pell <yeasah at schwide.net>
Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The previous DISEQC code didn't wait, so it was unreliable

Signed-off-by: Yeasah Pell <yeasah at schwide.net>
Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Current debug messages at cx24123 are next to useless, since they don't
print the values sent/read to registers. With this patch, debug=1 will
show comprehensive messages. debug=2 will show also read/write operations
at I2C bus.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>

- fixed the reception of channels with low symbol rates.
  ( The VGA1 and VGA2 offsets recommended by cx24109 docs for
  symbol rates from 1 to 5 MSps do not work. I changed them
  to values found experimentally. The charge pump current
  and FILTUNE voltage are now set to values recommended in
  the docs. This improves reception for symbol rates < 15 MSps.
  The values written in the SYSSymbolRate registers are calculated
  with better precision. )
		     
- fixed the cx24123_get_fec() function. It was returning the values
  for DCII mode.
- removed some unused variables

Signed-off-by: Vadim Catana <skystar at moldova.cc>
Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

In several places we use dev->devno right after we kfree() dev.  This fixes
coverity bug id #1065
Signed-off-by: NEric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

V4L1 API is depreciated and should be removed soon from kernel. This patch
adds two new options, one to disable V4L1 drivers, and another to disable
V4L1 compat module. This way, it would be easy to check what still depends
on V4L1 stuff, allowing also to test if app works fine with V4L2 only support.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Witout this patch tv out don't work properly with my pvr350 card.
Signed-off-by: NJose Alberto Reguero <jareguero@telefonica.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The computation in cx88_risc_buffer suffers from the mistake:
a non-zero padding value can cause more page borders to be crossed,
leading to big buffer over-runs.  
This patch changes the additive constant from 3 + 4 to 4
It also changees the constant in cx88_risc_databuffer from 3 + 4 to 2,
because 2 dwords are the correct vaule.
Signed-off-by: NDuncan Sands <baldrick@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

It looks like the HD3000 was prototyped with the 7610 tuner when
the driver was developed, but the cards appear to have always shipped
with the 7612 tuner and the driver was never adjusted for it.
The definition needs to be corrected.
- The HD-3000 was prototyped with a Thomson DTT7610,
  but production versions used a DTT7612 tuner.
- This patch changes both dvb-pll settings and V4L tuner type.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

When pluto2 were selected, all other module dependencies were
just discarded.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Spotted a couple more places where it fails to check if
dvb_register_adapter() fails.
Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Now that the CI code reinitialises the frontend, need to move the CI
initialisation to after the frontend init in order to ensure the frontend is
always in a good state. Fixes an oops caused by the frontend being NULL as
well.
Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

When disable_ir=1 parameter is used, or when saa7134_input_init1()
fails for any other reason, dev->remote will remain NULL, and the
driver will oops in saa7134_hwinit2().  Therefore dev->remote must be
checked before dereferencing.
Signed-off-by: NSergey Vlasov <vsu@altlinux.ru>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>