Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Or going from tiled to untiled may break.
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

While debugging Haswell link train failures I observed that we never
try the maximum voltage configuration more than once consecutively. We
start the training, the monitor keeps telling us to increase the
voltage, then when we reach the maximum we just go back to the start
(because of the "memset" above "voltage_tries = 0"). When we reach
this point, we keep alternating between the maximum and the minimum
voltages until we give up.

The DP spec suggests that we should try the same voltage 5 times
before giving up. This patch makes us try the maximum voltage at
least 5 times before going back to the minimum voltages.

This patch does not fix any particular bug I'm aware of.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We have way too much lying hardware to rely on a simple "does someone
answer on the ddc i2c address?" check. And now it's unused, so just
kill it.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Somehow detect_ddc manages to fall through all checks when we think
that something responds on the ddc i2c address, but the edid read
failed. Fix this up by explicitly checking for this case.

This fixes a regression on newer chips because since

commit aaa37730
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Sat Jun 16 15:30:32 2012 +0200

    drm/i915/crt: Do not rely upon the HPD presence pin

we use ddc detection also on hotplug capable platforms. And one of
these reads all 0s for any i2c transaction if nothing is connected to
the vga port.

v2: Implement Chris Wilson's review:
- simplify logic, default to "nothing detected"
- kill stale comment
- BUG_ON(!crt->type != ANALOG)

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=51900Tested-by: NYang Guang <guang.a.yang@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

I so totally suck.

This can cause a black screen if (for whatever reason) the bios
hasn't set this bit itself.

This regression has been introduced in

commit 7cf41601
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Tue Jun 5 10:07:09 2012 +0200

    drm/i915: clear up backlight #define confusion on gen4+
Tested-by: NKenneth Graunke <kenneth@whitecape.org>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Having had to dive into the bspec to understand what each stage of the
workaround meant, and how that the ring broadcasting IDLE corresponded
with the GT powering down the ring (i.e. rc6) add comments to aide
the next reader.

And since the register "is used to control all aspects of PSMI and power
saving functions" that makes it quite interesting to inspect with
regards to RC6 hangs, so add it to the error-state.

v2: Rediscover the piece of magic, set the RNCID to 0 before waiting for
the ring to wake up.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

It never quite worked despite the numerous workarounds, yet I still see
people trying to use this hardware and filing bug reports. As we no
longer even try to implement the workarounds, since 6a233c78
(drm/i915/ringbuffer: kill snb blt workaround), simply disable the ring.

v2: Add a message to inform the user about the limited capabilities of
their pre-production hardware.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This initializes power wells within the modeset_init_hw routine.
Testing has shown that this works for both driver load time and for
suspend-resume code paths.
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

There is little point waking up every 10ms to service an interrupt which
we then promptly ignore. So only program the the PMIER to enable
interrupts for those events which we do handle, not all of them!
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Eugeni Dodonov <eugeni.dodonov@intel.com>
Cc: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

There were some fields missed. Daniel pointed this out in review, and I
know I fixed it, but something happened somehow and some time.
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

*sigh* the docs had it spelled wrong, corrected it, and then proceeded
to re-do the original error. The original code preserved this history,
and this patch attempts to keep in sync with the current docs.
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Userspace uses long in quite a few places more than the kernel. Which
gives me neat proof that I'm the only guy on this side of the galaxy
who ever tried to run glxgears on a 64bit machine with sis graphics on
linux.

Note that the longs in drm_sis_mem_t aren't aligned properly, so this
won't even work with 32bit userspace on 64bit kernel as-is. Hence the
patch can't break that, either.

Nope, I'm not nuts enough to write the 32bit ioctl compat layer for
this and test it with some wine app. Even though hunting the ebay
dungeons for a sis card actually supported by the mesa drivers casts
some doubts on this ...
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDave Airlie <airlied@redhat.com>

With the last patch to ditch DMA_QUEUE support, we should be able
to call the dma cleanup uncoditionally, even when the master has
disappeared.

Do so because it just makes more sense.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Absolutely unused. All the values are only ever initialized and
then used at most in some debug printout functions.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Only one driver (i810) even sets that flag. Now the actual locking
code uncoditionally promotes lock->context to an unsigned int.

Closer inspection of the userspace reveals that the drm lock context
is defined as an unsigned int (at least on linux). I suspect we just
have a strange case of signedness confusion going on.

Tested on my i815, doesn't seem to break anything.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDave Airlie <airlied@redhat.com>

All leftover users either haven't set DRIVER_HAVE_DMA, in which
case this will never be called, or use the drm_core implementation.

Call that directly in the only callsite.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The reclaim_buffers function of the savage driver actually wants to run
with the hw_lock held - at least there are printks in the call-chain
to that effect. But the drm core only calls reclaim_buffers as used
by savage _after_ forcefully dropping the hwlock (in case it's still
hold by the closing fd).

So do the same idlelock dance as for the other dma drivers and hope
that papers over any issues.

v2: Don't let the idlelock linger around.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: NTormod Volden <debian.tormod@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

i810 was the last user of this code, with that gone, kill it.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This reverts commit 6e877b57,
reinstating the original commit:

commit 87499ffd
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Tue Oct 25 23:51:24 2011 +0200

    drm/i810: cleanup reclaim_buffers

    My dear old i815 always hits the deadlocked on reclaim_buffers
    warning. Switch over to the idlelock duct-tape on hope that
    works better. I've fired up my i815 and now closing glxgears doesn't
    take 5 seconds anymore. \o/

The original problem with that was that I've moved it ahead in the
series so that it could be included despite some patches not being
ready quite yet. The little problem is that this patch required some
of the previous rework to work correctly.

Now that everything is in the right order again, this actually works
on my i810 and does speed up closing gl apps as the original commit
claimed. Without hanging the machine, as the revert says.
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The only two users are now folded into the drivers preclose functions,
so this is unused.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Like for via.

v2: Actually drop the idlelock again if taken.

v3: Fixup.

v4: Fixup the "has master" vs. "is master" confusion the refactor
introduced.

v5: Drop the idlelock in the early return path.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDave Airlie <airlied@redhat.com>

A few things
- kill reclaim_buffers, it's never ever called because via does not set
  DRIVER_HAVE_DMA
- inline the idlelock dance into the buffer reclaim logic and make it
  a simple preclose cleanup function
- directly call the the dma_quiescent function and kill the needless
  if check.

v2: Actually drop the idlelock when we take it. Reported by James
Simmons.

v3: Rebased onto latest drm-next.

v4: Fixup the refactor.

v5: More fixup the refactor - I've accidentally changed the check for
any master to checking whether the closing fd is the master.

v6: Don't forget to drop the idlelock in the early return path, too.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This ports over the dpms code from udlfb, and should mean
a better chance of turning on some udl devices.
Signed-off-by: NDave Airlie <airlied@redhat.com>

This check the root ports supported link speeds and enables
GEN2 mode if the 5.0 GT link speed is available.

The first 3.0 cards are SI so they will probably need more investigation.
Signed-off-by: NDave Airlie <airlied@redhat.com>

This should work for PCIE3.0 as well.
Signed-off-by: NDave Airlie <airlied@redhat.com>

We need these for detecting the max link speed for drm drivers.
Acked-by: NBjorn Helgaas <bhelgass@google.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Print various CP register that have valuable informations regarding
GPU lockup.
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

we are referencing the pointer after doing alloc_apertures,
as alloc_apertures kzallocs, the kzalloc may fail and we get a NULL.

so we need to check for NULL before we dereference this pointer
Signed-off-by: NDevendra Naga <devendra.aaru@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This could previously fail if either of the enabled displays was using a
horizontal resolution that is a multiple of 128, and only the leftmost column
of the cursor was (supposed to be) visible at the right edge of that display.

The solution is to move the cursor one pixel to the left in that case.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=33183

Cc: stable@vger.kernel.org
Signed-off-by: NMichel Dänzer <michel.daenzer@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The passed mode must not be modified by the operation, make it const.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

It's unused. At it confused me quite a bit until I've discovered that.

Cc: dri-devel@lists.freedesktop.org
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Go through the interface vtable instead, because not everyone might be
using the crtc helper code.

Cc: dri-devel@lists.freedesktop.org
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Ok, this requires quite a dance to actually hit:
1) We plug in a 2nd screen, enable it in both X and (by vt-switching)
in the fbcon.
2) We disable that screen again in with xrandr.
3) We vt-switch again, so that fbcon displays on the 2nd screen, but X
on the first screen. This obviously needs a driver that doesn't switch
off unused functions when regaining the VT.
3) When X controls the vt, we unplug that screen.

Now drm_fb_helper_hotplug_event we noticed that that some crtcs are
bound, but because we still have the fbcon on the 2nd screeen we also
have bound set. Which means the fbcon wrongly assumes it's in control
of everything an happily disables the output on the 2nd screen, but
enables its fb on the first screen.

Work around this issue by counting how many crtcs are bound and how
many are bound to fbcon and assuming that when fbcon isn't bound to
all of them, it better not touch the output configuration.

Conceptually this is the same as only restoring the fbcon output
configuration on the driver's ->lastclose, when we're sure that no one
else is using kms. So this should be consistent with existing kms
drivers.

Chris has created a separate patch for the intel ddx, but I think we
should fix this issue here regardless - the fbcon messing with the
output config while it's not fully in control simply isn't a too
polite behaviour.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=50772Tested-by: NMaxim A. Nikulin <M.A.Nikulin@gmail.com>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This contains all the radeon documentation rebased on top of the ib fixes.

* 'next' of git://people.freedesktop.org/~deathsimple/linux:
  drm/radeon: fix SS setup for DCPLL
  drm/radeon: fix up pll selection on DCE5/6
  drm/radeon: start to document evergreen.c
  drm/radeon: start to document the functions r100.c
  drm/radeon: document VM functions in radeon_gart.c (v3)
  drm/radeon: document non-VM functions in radeon_gart.c (v2)
  drm/radeon: document radeon_ring.c (v4)
  drm/radeon: document radeon_fence.c (v2)
  drm/radeon: document radeon_asic.c
  drm/radeon: document radeon_irq_kms.c
  drm/radeon: document radeon_kms.c
  drm/radeon: document radeon_device.c (v2)
  drm/radeon: add rptr save support for r1xx-r5xx
  drm/radeon: update rptr saving logic for memory buffers
  drm/radeon: remove radeon_ring_index()
  drm/radeon: update ib_execute for SI (v2)
  drm/radeon: fix const IB handling v2
  drm/radeon: let sa manager block for fences to wait for v2
  drm/radeon: return an error if there is nothing to wait for

Need to actually set the SS parameters rather than just 0.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>

Selecting ATOM_PPLL_INVALID should be equivalent as the
DCPLL or PPLL0 are already programmed for the DISPCLK, but
the preferred method is to always specify the PLL selected.
SetPixelClock will check the parameters and skip the
programming if the PLL is already set up.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>

Still a lot to do.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>

Still a lot more to do.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>