These two flags are used for the same purpose, just
combine them into a no-ir flag to annotate no initiating
radiation is allowed.

Old userspace sending either flag will have it treated as
the no-ir flag. To be considerate to older userspace we
also send both the no-ir flag and the old no-ibss flags.
Newer userspace will have to be aware of older kernels.

Update all places in the tree using these flags with the
following semantic patch:

@@
@@
-NL80211_RRF_PASSIVE_SCAN
+NL80211_RRF_NO_IR
@@
@@
-NL80211_RRF_NO_IBSS
+NL80211_RRF_NO_IR
@@
@@
-IEEE80211_CHAN_PASSIVE_SCAN
+IEEE80211_CHAN_NO_IR
@@
@@
-IEEE80211_CHAN_NO_IBSS
+IEEE80211_CHAN_NO_IR
@@
@@
-NL80211_RRF_NO_IR | NL80211_RRF_NO_IR
+NL80211_RRF_NO_IR
@@
@@
-IEEE80211_CHAN_NO_IR | IEEE80211_CHAN_NO_IR
+IEEE80211_CHAN_NO_IR
@@
@@
-(NL80211_RRF_NO_IR)
+NL80211_RRF_NO_IR
@@
@@
-(IEEE80211_CHAN_NO_IR)
+IEEE80211_CHAN_NO_IR

Along with some hand-optimisations in documentation, to
remove duplicates and to fix some indentation.
Signed-off-by: NLuis R. Rodriguez <mcgrof@do-not-panic.com>
[do all the driver updates in one go]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Putting the context id of the primary phy context in
the placeholder of the secondary is obviously a bad
idea.
Spotted by smatch.

Fixes: dac94da8 ("iwlwifi: mvm: new BT Coex API")
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Reported by "make includecheck"

Tested that the corresponding sources still compile well on x86
Signed-off-by: NMichael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

If the firmware image that we attempt to load doesn't
actually exist we have a broken firmware file or other
code not checking things correctly, so warn in such a
case. Also avoid assigning cur_ucode/ucode_loaded then.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When writing the disable_power_off value, the LPRX
enable value also gets written unintentionally, so
fix that by adding the missing break statement.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This can be useful when using the device as a sniffer.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Having a WARN_ON() followed by a printed message is
less useful than having the message in the warning
so move the message.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When we disassociate, mac80211 removes the station and
then, it sets the bss it unsets the assoc bool in bss_info.

Since the firwmware wants it the opposite (first set the
MAC context as unassoc, and only then, remove the STA of
the API), we have a small period of time in which the STA
in firmware doesn't have a valid ieee80211_sta pointer.
During that time, iwl_mvm_vif->ap_sta_id, is still set
to the STA in firmware that represent the AP.

This avoids:

[ 4481.476246] BUG: unable to handle kernel NULL pointer dereference at 00000045
[ 4481.479521] IP: [<f8416a6a>] iwl_mvm_bt_coex_reduced_txp+0x7a/0x190 [iwlmvm]
[ 4481.482023] *pde = 00000000
[ 4481.484332] Oops: 0000 [#1] SMP DEBUG_PAGEALLOC
[ 4481.486897] Modules linked in: netconsole configfs autofs4 rfcomm(O) bnep(O) nfsd nfs_acl auth_rpcgss exportfs nfs lockd binfmt_misc sunrpc fscache arc4 iwlmvm(O) mac80211(O) btusb(O) iwlwifi(O) bluetooth(O) cfg80211(O) snd_hda_codec_hdmi coretemp dell_wmi snd_hda_codec_idt compat(O) dell_laptop aesni_intel i915 sparse_keymap dcdbas cryptd psmouse serio_raw aes_i586 microcode snd_hda_intel drm_kms_helper snd_hda_codec drm snd_pcm snd_timer i2c_algo_bit video intel_agp intel_gtt snd soundcore snd_page_alloc crc32c_intel ahci sdhci_pci libahci sdhci mmc_core e1000e xhci_hcd [last unloaded: configfs]
[ 4481.502983]
[ 4481.505599] Pid: 6507, comm: kworker/0:1 Tainted: G           O 3.4.43-dev #1 Dell Inc. Latitude E6430/0CMDYV
[ 4481.508575] EIP: 0060:[<f8416a6a>] EFLAGS: 00010246 CPU: 0
[ 4481.511248] EIP is at iwl_mvm_bt_coex_reduced_txp+0x7a/0x190 [iwlmvm]
[ 4481.513947] EAX: ffffffea EBX: 00000002 ECX: 00000001 EDX: 00000001
[ 4481.516710] ESI: ec6f0f28 EDI: 00000000 EBP: e8175dfc ESP: e8175d9c
[ 4481.519445]  DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
[ 4481.522185] CR0: 8005003b CR2: 00000045 CR3: 01a5e000 CR4: 001407d0
[ 4481.524950] DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
[ 4481.527768] DR6: ffff0ff0 DR7: 00000400
[ 4481.530565] Process kworker/0:1 (pid: 6507, ti=e8174000 task=e8032b20 task.ti=e8174000)
[ 4481.533447] Stack:
[ 4481.536379]  e472439f 00003a12 e8032b20 e8033048 00000001 e8175ddc 00000246 e8033040
[ 4481.540132]  00000002 01814990 ec4d1ddc e8175dcc 00000000 00000000 00000000 00000000
[ 4481.543867]  00000000 00000000 00000001 000001c8 009b0002 ec4d1ddc ec6f0f28 00000000
[ 4481.547633] Call Trace:
[ 4481.550578]  [<f8418027>] iwl_mvm_bt_rssi_event+0x197/0x220 [iwlmvm]
[ 4481.553537]  [<f840919c>] iwl_mvm_stat_iterator+0xdc/0x240 [iwlmvm]
[ 4481.556582]  [<f8d129c2>] __iterate_active_interfaces+0xe2/0x1f0 [mac80211]
[ 4481.559544]  [<f84090c0>] ? iwl_mvm_update_smps+0x90/0x90 [iwlmvm]
[ 4481.562519]  [<f84090c0>] ? iwl_mvm_update_smps+0x90/0x90 [iwlmvm]
[ 4481.565498]  [<f8d12b0c>] ieee80211_iterate_active_interfaces+0x3c/0x50 [mac80211]
[ 4481.568421]  [<f8409b43>] iwl_mvm_rx_statistics+0xb3/0x130 [iwlmvm]
[ 4481.571349]  [<f8405431>] iwl_mvm_async_handlers_wk+0xc1/0xf0 [iwlmvm]
[ 4481.574251]  [<c1052915>] ? process_one_work+0x105/0x5c0
[ 4481.577162]  [<c1052991>] process_one_work+0x181/0x5c0
[ 4481.580025]  [<c1052915>] ? process_one_work+0x105/0x5c0
[ 4481.582861]  [<f8405370>] ? iwl_mvm_rx_fw_logs+0x20/0x20 [iwlmvm]
[ 4481.585722]  [<c10530f1>] worker_thread+0x121/0x2c0
[ 4481.588536]  [<c1052fd0>] ? rescuer_thread+0x1d0/0x1d0
[ 4481.591323]  [<c105af0d>] kthread+0x7d/0x90
[ 4481.594059]  [<c105ae90>] ? flush_kthread_worker+0x120/0x120
[ 4481.596868]  [<c15b7cc2>] kernel_thread_helper+0x6/0x10
[ 4481.599605] Code: 9d de c3 c8 85 c0 74 0d 80 3d f8 ae 42 f8 00 0f 84 dc 00 00 00 8b 45 c8 0f b6 d3 31 ff 89 55 c0 8b 84 90 d8 03 00 00 0f b6 55 c7 <38> 50 5b 89 45 bc 0f 84 a8 00 00 00 a1 e4 d2 04 c2 85 c0 0f 84
[ 4481.611782] EIP: [<f8416a6a>] iwl_mvm_bt_coex_reduced_txp+0x7a/0x190 [iwlmvm] SS:ESP 0068:e8175d9c
[ 4481.614985] CR2: 0000000000000045
[ 4481.687441] ---[ end trace b11bc915fbac4412 ]---
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The number of commands can never be negative, so it should
be using an unsigned type. This also shuts up an smatch
warning elsewhere in the code.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Change old UAPSD bit to PM_CMD_SUPPORT, and add a new bit to indicate
real UAPSD support.
Don't use UAPSD when the firmware doesn't support it.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

mac80211_hwsim canceled beacon_timer on any vif changing from enabled
to disabled beaconing. This breaks cases where there are multiple
beaconing vifs and only one of them is removed. Fix this by tracking
beaconing status per vif and disable beacon_timer only if no active vif
remain with beaconing enabled.
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In order to reconfigure the correct reg domain on
recovery, we have to save the current configuration
before clearing it (wl->reg_ch_conf_pending is
considered before configuring a new regdomain).
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

wlcore configures different dwell times according to number
of active interfaces (in order to prevent hurting VO during
scan).

However, determining active vif only according to
bss_conf->idle is not explicit enough, and might result
in non-started vifs being counted as started as well
(e.g. unassociated sta during sta).

Fix it by checking for explicit conditions according
to the vif type.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

Make sure the FW is awake when entering recovery. This is useful for
reading the FW panic log and also some FW registers giving us crash
report stats.

We must do this before interrupts are disabled since we rely on an
interrupt to complete the wakeup.

If the wakeup fails, continue recovery normally. All read/writes will be
blocked and won't do any harm.
Signed-off-by: NBarak Bercovitz <barak@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

The FW panic log is read during recovery work.
It has to be stopped properly before reading. otherwise,
inconsistent data might be read which cause the driver
to freeze.

__wlcore_cmd_send has to work for the special case of
CMD_STOP_FWLOGGER, while in recovery, in order to stop
the fw log before it is read.
Signed-off-by: NBarak Bercovitz <barak@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

Reading FW panic log is only supported in host mode (SDIO)
Signed-off-by: NBarak Bercovitz <barak@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

FW memory block size and FW log end marker parameters
are added to wl structure and are initialized per
chip architecture.

convert_hwaddr hw operation is added to convert chip
dependent FW internal address.

Copy from FW log is also simplified to copy the entire
memory block as FW logger utility is repsponsible
for parsing of FW log content.
Signed-off-by: NIgal Chernobelsky <igalc@ti.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

update the fw logger mode to continuous, and output to dbgpins (uart).
Signed-off-by: NIdo Reis <idor@ti.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

number of fwlog mem_blocks can be configured using module param.
this is a fw debug feature: in case a large fw log data is busrted during
a short period of time, the memory get filled and data is lost.
this allows us to dynamicly set the fw log mem_block usage, although
configuring more mem_block for logger comes at the expense of TP.
Signed-off-by: NYair Shapira <yair.shapira@ti.com>
Signed-off-by: NIdo Reis <idor@ti.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

Change interrogate command prototype to have command size
and returned buffer length.
This fixes the issue when command parameters are needed to
be passed to FW in addition to acx header as in the case with
get RSSI command, where role_id has to be passed.
Signed-off-by: NIgal Chernobelsky <igalc@ti.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

Add new ap_event_mask field, to indicate events that
should be unmasked only when there's an ap interface.

This is done in order to avoid spurious wakeups
when we don't care about the incoming event anyway.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

Print current active channel/s and a role type for
that channel in the driver_state debugfs.
Signed-off-by: NVictor Goldenshtein <victorg@ti.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

Driver default config is aligned with phy default parameters.

Now that RDL1_3 has 2 antennas defined by default we need to explicitly
define ht.mode to HT_MODE_WIDE to have SISO40 as default.
Signed-off-by: NYair Shapira <yair.shapira@ti.com>
Signed-off-by: NIgal Chernobelsky <igalc@ti.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

Use the module_pci_driver() macro to make the code simpler
by eliminating module_init and module_exit calls.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The PCI and SoC specific drivers are using separate
code now so it is not reasonable to use the same
module for both drivers anymore.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The 'rt2800pci_hwcrypt_disabled' function is the
only PCI specific callback which is used by the
SoC driver. Create a clone of that to get rid of
the dependency.

Even though the two functions are using the same
variable, but the SoC specific code will be moved
into a separate module which will have its own
'modparam_nohwcrypt' variable.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move the function into the rt2800mmio module, in order
to make it usable from other modules.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The function is called for PCI and SoC devices
however the MCU related part of the function
has no effect on SoC devices. Move the common
part of the function into a separate helper and
use that for the SoC devices.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The function contain code for SoC devices only.
Rename the function to 'rt2800soc_disable_radio'
and move it to the SoC specific section. Use
the renamed function in the SoC specific code
only and remove the 'if rt2x00_is_soc(rt2x00dev)'
condition from the function body.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The 'rt2800pci_set_state' function uses MCU commands
to set the device state, however these have no effect
on SoC devices. Use a different set_state callback
which does not use the MCU fcuntions.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use empty firmware callbacks for SoC devices because those
don't require firmware.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Rename the 'rt2800pci_read_eeprom_soc function' to
'rt2800soc_read_eeprom' and use that directly in the
SoC specific 'rt2800_ops' structure. Also move the
'rt2800pci_eeprom_read' function into an 'ifdef PCI'
section and remove the 'rt2800pci_read_eeprom_soc'
call from that.

Additionally, remove the dummy inline eeprom functions.
Those are not used anymore.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This makes it possible to use different callback
functions for PCI and SoC devices which will allow
to move the SoC driver into a separate module.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move the functions into a separate module, in order
to make those usable from other modules.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The functions are used for devices with memory
mapped I/O and contain no PCI specific code at
all. Use rt2800mmio prefix instead of rt2800pci
in the function names to reflect that.

The patch contains no functional changes.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move the functions into a separate module, in order
to make those usable from other modules. Also move
the queue register offset macros from rt2800pci.h
into rt2800mmio.h.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The functions are used for devices with memory
mapped I/O and contain no PCI specific code at
all. Use rt2800mmio prefix instead of rt2800pci
in the function names to reflect that.

The patch contains no functional changes.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move the functions into a separate module, in order
to make those usable from other modules.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The functions are used for devices with memory
mapped I/O and contain no PCI specific code at
all. Use rt2800mmio prefix instead of rt2800pci
in the function names to reflect that.

The patch contains no functional changes.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move the functions into a separate module, in order
to make those usable from other modules. Also move
the RX descriptor related defines from rt2800pci.h
into rt2800mmio.h
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>