Allow systems to tune detection rate and debounce suitably for their
mechanical parameters.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

With some GPIO control it is possible to detect microphones in a wider
range of configurations by directly measuring the microphone impedance
when the HPDET method cannot distinguish between the behaviour of the
two grounds. Allow a GPIO to be provided in platform data and use it to
implement this behaviour.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NMyungjoo Ham <myungjoo.ham@samsung.com>

The accessory detection functionality in Arizona devices is flexible and
supports several system designs in addition to the default one implemented
by the existing driver. One such design uses the HPDET feature to determine
what kind of accessory is present by comparing measurements taken with the
two headphone grounds available on the device, implement that if selected
by platform data.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NMyungjoo Ham <myungjoo.ham@samsung.com>

Some system designs provide an input on GPIO5 which in conjunction with
the jack detection feature indicates the presence of an accessory.
Support such systems, using the microphone clamp feature to minimise
wakeups of the processor.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NMyungjoo Ham <myungjoo.ham@samsung.com>

Allow configuration of the rise time for MICBIAS via platform data, the
delay required depends on things like the external component selection.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Acked-by: NMyungJoo Ham <myungjoo.ham@samsung.com>

The Arizona CODECs contain a haptics module providing vibration feedback
support. Implement basic support for this, providing simple start/stop and
signal magnitude control.

Since the output path for haptics is routed through the CODEC audio routing
it is modelled as a signal generator within ASoC, the haptics driver calls
DAPM to start and stop the output drivers. An appropriate output path must
be configured via ALSA to connect the haptics source to the correct output.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The WM5110 is a highly-integrated low-power audio system for smartphones,
tablets and other portable audio devices. It combines an advanced DSP
feature set with a flexible, high-performance audio hub CODEC.

The support is based on the Arizona core driver.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The registers have stride 2 so we can write the loop properly now.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Several forthcoming Wolfson devices are based on a common platform
known as Arizona allowing a great deal of reuse of driver code. This
patch adds core support for these devices.

In order to handle systems which do not use the generic clock API a
simple wrapper for the 32kHz clock domain in the devices is provided.
Once the generic clock API is widely available this code will be moved
over to use that.

For simplicity some WM5102 specific code is included in the core driver,
the effort involved in splitting the device out isn't worth it.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>