Convert the opal hvc driver to use the new irqchip to register for
opal events. As older firmware versions may not have device tree
bindings for the interrupt parent we just use a hardcoded hwirq based
on the event number.
Signed-off-by: NAlistair Popple <alistair@popple.id.au>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Convert the opal ipmi driver to use the new irq interface for events.
Signed-off-by: NAlistair Popple <alistair@popple.id.au>
Acked-by: NCorey Minyard <cminyard@mvista.com>
Cc: Corey Minyard <minyard@acm.org>
Cc: openipmi-developer@lists.sourceforge.net
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Whenever an interrupt is received for opal the linux kernel gets a
bitfield indicating certain events that have occurred and need handling
by the various device drivers. Currently this is handled using a
notifier interface where we call every device driver that has
registered to receive opal events.

This approach has several drawbacks. For example each driver has to do
its own checking to see if the event is relevant as well as event
masking. There is also no easy method of recording the number of times
we receive particular events.

This patch solves these issues by exposing opal events via the
standard interrupt APIs by adding a new interrupt chip and
domain. Drivers can then register for the appropriate events using
standard kernel calls such as irq_of_parse_and_map().
Signed-off-by: NAlistair Popple <alistair@popple.id.au>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Most of the OPAL subsystems are always compiled in for PowerNV and
many of them need to be initialised before or after other OPAL
subsystems. Rather than trying to control this ordering through
machine initcalls it is clearer and easier to control initialisation
order with explicit calls in opal_init.
Signed-off-by: NAlistair Popple <alistair@popple.id.au>
Cc: Mahesh Jagannath Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Fastsleep is one of the idle state which cpuidle subsystem currently
uses on power8 machines. In this state L2 cache is brought down to a
threshold voltage. Therefore when the core is in fastsleep, the
communication between L2 and L3 needs to be fenced. But there is a bug
in the current power8 chips surrounding this fencing.

OPAL provides a workaround which precludes the possibility of hitting
this bug. But running with this workaround applied causes checkstop
if any correctable error in L2 cache directory is detected. Hence OPAL
also provides a way to undo the workaround.

In the existing implementation, workaround is applied by the last thread
of the core entering fastsleep and undone by the first thread waking up.
But this has a performance cost. These OPAL calls account for roughly
4000 cycles everytime the core has to enter or wakeup from fastsleep.

This patch introduces a sysfs attribute (fastsleep_workaround_applyonce)
to choose the behavior of this workaround.

By default, fastsleep_workaround_applyonce = 0. In this case, workaround
is applied/undone everytime the core enters/exits fastsleep.

fastsleep_workaround_applyonce = 1. In this case the workaround is
applied once on all the cores and never undone. This can be triggered by
echo 1 > /sys/devices/system/cpu/fastsleep_workaround_applyonce

For simplicity this attribute can be modified only once. Implying, once
fastsleep_workaround_applyonce is changed to 1, it cannot be reverted
to the default state.
Signed-off-by: NShreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Reviewed-by: NPreeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This is a cleanup patch; doesn't change any functionality. Moves
all cpuidle related code from setup.c to a new file.
Signed-off-by: NShreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Reviewed-by: NPreeti U Murthy <preeti@linux.vnet.ibm.com>
[mpe: Fix the SMP=n build by including asm/smp.h in idle.c]
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Currently, cpu_online_cores_map returns a mask, which for every core with
at least one online thread, has the bit for thread 0 of the core set to 1,
and the bits for all other threads of the core set to 0. But thread 0 of
the core itself may not be online always. In such cases, if the returned
mask is used for IPI, then it'll cause IPIs to be skipped on cores where
the first thread is offline, because the IPI code refuses to send IPIs to
offline threads.

Fix this by setting the bit of the first online thread in the core.
This is done by fixing this in the underlying function
cpu_thread_mask_to_cores.

The result has the property that for all cores with online threads, there
is one bit set in the returned map. And further, all bits that are set in
the returned map correspond to online threads.
Signed-off-by: NShreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Reviewed-by: NPreeti U Murthy <preeti@linux.vnet.ibm.com>
[ Changelog from Michael Ellerman <mpe@ellerman.id.au> ]
Reviewed-by: NGautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The commit 8170a83f ("powerpc: Wireup the kcmp syscall to sys_ni") has
disabled the kcmp syscall for powerpc.  This has been done due to the use
of unsigned long parameters which may require a dedicated wrapper to handle
32bit process on top of 64bit kernel.  However in the kcmp() case, the 2
unsigned long parameters are currently only used to carry file descriptors
from user space to the kernel.  Since such a parameter is passed through
register, and file descriptor doesn't need to get extended, there is,
today, no need for a wrapper.

In the case there will be a need to pass address in or out of this system
call, then a wrapper could be required, it will then be to care of it.

As today this is not the case, it is safe to enable kcmp() on powerpc.

Tested (by Laurent) on 64-bit, 32-bit, and 32-bit userspace on 64-bit
kernel using tools/testing/selftests/kcmp [mpe].
Signed-off-by: NLaurent Dufour <ldufour@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The only little endian configuration we support is ppc64le, all other
configurations are big endian.

So we should only offer a choice of endian if we're building for 64-bit
Book3S, ie. PPC_BOOK3S_64.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Currently, the macro IS_BRIDGE is not used any where.
This patch just removes it.
Signed-off-by: NWei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

As the comment indicates, powernv_eeh_get_state() will inform EEH core to
delay 1 second. This means the delay doesn't happen when
powernv_eeh_get_state() returns.

This patch moves the delay subtraction just before msleep(), which is the
same logic in pseries_eeh_wait_state().
Signed-off-by: NWei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

To retrieve the PCI slot state, EEH driver would set a timeout for that.
While current comment is not aligned to what the code does.

This patch fixes those comments according to the code.
Signed-off-by: NWei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

struct pci_io_addr_range{} stores the information of pci resources. It
would be better to keep these related fields have the same type as in
struct resource{}.

This patch fixes the start/end/flags type in struct pci_io_addr_range{} to
have the same type as in struct resource{}.
Signed-off-by: NWei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The patch adds one more EEH sub-command (VFIO_EEH_PE_INJECT_ERR)
to inject the specified EEH error, which is represented by
(struct vfio_eeh_pe_err), to the indicated PE for testing purpose.
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: NDavid Gibson <david@gibson.dropbear.id.au>
Acked-by: NAlex Williamson <alex.williamson@redhat.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The patch defines PCI error types and functions in uapi/asm/eeh.h
and exports function eeh_pe_inject_err(), which will be called by
VFIO driver to inject the specified PCI error to the indicated
PE for testing purpose.
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

There are two equivalent sets of PE state constants, defined in
arch/powerpc/include/asm/eeh.h and include/uapi/linux/vfio.h.
Though the names are different, their corresponding values are
exactly same. The former is used by EEH core and the latter is
used by userspace.

The patch moves those constants from arch/powerpc/include/asm/eeh.h
to arch/powerpc/include/uapi/asm/eeh.h, which are expected to be
used by userspace from now on. We can't delete those constants in
vfio.h as it's uncertain that those constants have been or will be
used by userspace.
Suggested-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

OpenPower BMC machines do not place any sysparams in the device tree, so
at every boot we get a warning:

 [    0.437176] SYSPARAM: Opal sysparam node not found

Remove the warning, and reorder the init so we don't peform allocations
when there is no sysparam node in the device tree.
Signed-off-by: NJoel Stanley <joel@jms.id.au>
Acked-by: NNeelesh Gupta <neelegup@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Traffic on the cbe-oss-dev list is more or less non-existent, other than
CC's from linuxppc.

It's seems like we may as well just send everyone to linuxppc and
archive the list.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
Acked-by: NJeremy Kerr <jk@ozlabs.org>

The only little endian configuration we support is ppc64le. As such if
we're building little endian we don't need a 32-bit VDSO, because there
is no 32-bit userspace.

This patch is a fairly ugly mess of #ifdefs, but is the minimal logic
required to disable the 32-bit VDSO. We can hopefully clean up the
result in future with some further refactoring.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

In vdso_fixup_features() we have start64/start32 and size64/size32, but
they have the same types, ie. void * and unsigned long.

They're only used to save the return value from find_sectionXX() for the
subsequent call to do_feature_fixups(), so there's no overlap in their
usage either.

So we can just consolidate them into start/size and avoid the
duplication.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

It's in the git history if we ever need it back.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

There is a bug in binutils 2.24 which causes miscompilation if we're
building little endian and using weak symbols (which the kernel does).

It is fixed in binutils commit 57fa7b8c7e59 "Correct elf_merge_st_other
arguments for weak symbols", which is in binutils 2.25 and has been
backported to the binutils 2.24 branch and has been picked up by most
distros it seems.

However if we're running stock 2.24 (no extra version) then the bug is
present, so check for that and bail.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

We have several checks for bad gcc versions in our Makefile. These don't
apply if we're building with clang, so skip them in that case.

The obvious check would be for ${COMPILER} = "gcc", but because of the
way the logic in the top level Makefile conditionally sets COMPILER,
it's possible that we're building with gcc but COMPILER was not set.

So instead check for ${COMPILER} != "clang", which we know is currently
the only other possibility.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Currently we print "Starting Linux PPC64" at boot. But we don't mention
anywhere whether the kernel is big or little endian.

If we print the utsname->machine value instead we get either "ppc64" or
"ppc64le" which is much more informative, eg:

  Starting Linux ppc64le #1 SMP Wed Apr 15 12:12:20 AEST 2015
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The pasemi MSI code is currently always built when MPIC=y && PCI_MSI=y.
It should not have any effect on other platforms, because it immediately
checks the MPIC's compatible property for "pasemi,pwrficient-openpic".

However it's odd that it's still built even when PASEMI=n. It also
needn't be in sysdev, as it's only used by pasemi. So move it into
platforms/pasemi, whereby it will only be built for PASEMI=y.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The STRICT_MM_TYPECHECKS code has bit-rotted over the years. To make it
possible to easily build test it, make it a CONFIG option.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Failure return from dlpar_configure_connector when dlpar adding cpus
results in leaking references to the cpus parent device node. Move the
call to of_node_put() prior to checking the result of
dlpar_configure_connector.

Fixes: 8d5ff320 ("powerpc/pseries: Make dlpar_configure_connector parent node aware")
Signed-off-by: NNathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The irq_domain_ops are not modified by the driver and the irqdomain core
code accepts pointer to a const data.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Pull drm fixes from Dave Airlie:
 "I really need to get back to sending these on my Friday, instead of my
  Monday morning, but nothing too amazing in here: a few amdkfd fixes, a
  few radeon fixes, i915 fixes, one tegra fix and one core fix"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm: Zero out invalid vblank timestamp in drm_update_vblank_count.
  drm/tegra: Don't use vblank_disable_immediate on incapable driver.
  drm/radeon: stop trying to suspend UVD sessions
  drm/radeon: more strictly validate the UVD codec
  drm/radeon: make UVD handle checking more strict
  drm/radeon: make VCE handle check more strict
  drm/radeon: fix userptr lockup
  drm/radeon: fix userptr BO unpin bug v3
  drm/amdkfd: Initialize sdma vm when creating sdma queue
  drm/amdkfd: Don't report local memory size
  drm/amdkfd: allow unregister process with queues
  drm/i915: Drop PIPE-A quirk for 945GSE HP Mini
  drm/i915: Sink rate read should be saved in deca-kHz
  drm/i915/dp: there is no audio on port A
  drm/i915: Add missing MacBook Pro models with dual channel LVDS
  drm/i915: Assume dual channel LVDS if pixel clock necessitates it
  drm/radeon: don't setup audio on asics that don't support it
  drm/radeon: disable semaphores for UVD V1 (v2)

misc i915 fixes.

* tag 'drm-intel-fixes-2015-05-08' of git://anongit.freedesktop.org/drm-intel:
  drm/i915: Drop PIPE-A quirk for 945GSE HP Mini
  drm/i915: Sink rate read should be saved in deca-kHz
  drm/i915/dp: there is no audio on port A
  drm/i915: Add missing MacBook Pro models with dual channel LVDS
  drm/i915: Assume dual channel LVDS if pixel clock necessitates it

Since commit 844b03f2 we make
sure that after vblank irq off, we return the last valid
(vblank count, vblank timestamp) pair to clients, e.g., during
modesets, which is good.

An overlooked side effect of that commit for kms drivers without
support for precise vblank timestamping is that at vblank irq
enable, when we update the vblank counter from the hw counter, we
can't update the corresponding vblank timestamp, so now we have a
totally mismatched timestamp for the new count to confuse clients.

Restore old client visible behaviour from before Linux 3.17, but
zero out the timestamp at vblank counter update (instead of disable
as in original implementation) if we can't generate a meaningful
timestamp immediately for the new vblank counter. This will fix
this regression, so callers know they need to retry again later
if they need a valid timestamp, but at the same time preserves
the improvements made in the commit mentioned above.
Signed-off-by: NMario Kleiner <mario.kleiner.de@gmail.com>
Cc: <stable@vger.kernel.org> #v3.17+

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Pull ARM fixes from Russell King:
 "A set of ARM fixes:

   - fix an off-by-one error in the iommu DMA ops, which caused errors
     with a 4GiB size.

   - remove comments mentioning the non-existent CONFIG_CPU_ARM1020_CPU_IDLE
     macro.

   - remove useless CONFIG_CPU_ICACHE_STREAMING_DISABLE blocks, where
     this symbol never appeared in any Kconfig.

   - fix Feroceon code to cope with a previous change correctly (it
     incorrectly left an additional word in an assembly structure
     definition)

   - avoid a misleading IRQ affinity warning in the ARM PMU code for
     IRQs which are already affine to their CPUs.

   - fix the node name printed in the IRQ affinity warning"

* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  ARM: 8352/1: perf: Fix the pmu node name in warning message
  ARM: 8351/1: perf: don't warn about missing interrupt-affinity property for PPIs
  ARM: 8350/1: proc-feroceon: Fix feroceon_proc_info macro
  ARM: 8349/1: arch/arm/mm/proc-arm925.S: remove dead #ifdef block
  ARM: 8348/1: remove comments on CPU_ARM1020_CPU_IDLE
  ARM: 8347/1: dma-mapping: fix off-by-one check in arm_setup_iommu_dma_ops

Pull samsung fixes from Kukjin Kim:
 "Here is Samsung fixes for v4.1.  Since I've missed to send this via
  arm-soc tree before v4.1-rc3, so I'm sending this to you directly

   - fix commit ea08de16 ("ARM: dts: Add DISP1 power domain for
     exynos5420") which causes 'unhandled fault: imprecise external
     abort' error when PD turned off.  ("make DP a consumer of DISP1
     power domain")

   - fix 's3c-rtc' probe failure on Odriod-X2/U2/U3 boards ("add
     'rtc_src' clock to rtc node for source clock of rtc")

   - fix typo for 'cpu-crit-0' trip point on exynos5420/5440

   - fix S2R failure on exynos5250-snow due to card power of Marvell
     WiFi driver (suspend/resume) ("add keep-power-in-susped to WiFi
     SDIO node")"

* tag 'samsung-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
  ARM: dts: Add keep-power-in-suspend to WiFi SDIO node for exynos5250-snow
  ARM: dts: Fix typo in trip point temperature for exynos5420/5440
  ARM: dts: add 'rtc_src' clock to rtc node for exynos4412-odroid boards
  ARM: dts: Make DP a consumer of DISP1 power domain on Exynos5420

Pull ARM SoC fixes from Arnd Bergmann:
 "A few patches have come up since the merge window.  The largest one is
  a rewrite of the PXA lubbock/mainstone IRQ handling.  This was already
  broken in 2011 by a change to the GPIO code and only noticed now.

  The other changes contained here are:

  MAINTAINERS file updates:

   - Ray Jui and Scott Branden are now co-maintainers for some of the
     mach-bcm chips, while Christian Daudt and Marc Carino have stepped
     down.

   - Andrew Victor is no longer maintaining at91.  Instead, Alexandre
     Belloni now becomes an official maintainer, after having done a
     bulk of the work for a while.

   - Baruch Siach, who added the mach-digicolor platform in 4.1 is now
     listed as maintainer

   - The git URL for mach-socfpga has changed

  Bug fixes:

   - Three bug fixes for new rockchip rk3288 code

   - A regression fix to make SD card support work on certain ux500
     boards

   - multiple smaller dts fixes for imx, omap, mvebu, and shmobile

   - a regression fiix for omap3 power consumption

   - a fix for regression in the ARM CCI bus driver

  Configuration changes:

   - more imx platforms are now enabled in multi_v7_defconfig"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (39 commits)
  MAINTAINERS: add Conexant Digicolor machines entry
  MAINTAINERS: socfpga: update the git repo for SoCFPGA
  ARM: multi_v7_defconfig: Select more FSL SoCs
  MAINTAINERS: replace an AT91 maintainer
  drivers: CCI: fix used_mask init in validate_group()
  bus: omap_l3_noc: Fix master id address decoding for OMAP5
  bus: omap_l3_noc: Fix offset for DRA7 CLK1_HOST_CLK1_2 instance
  ARM: dts: dra7: Fix efuse register size for ABB
  ARM: dts: am57xx-beagle-x15: Switch GPIO fan number
  ARM: dts: am57xx-beagle-x15: Switch UART mux pins
  ARM: dts: am437x-sk: reduce col-scan-delay-us
  ARM: dts: am437x-sk: fix for new newhaven display module revision
  ARM: dts: am57xx-beagle-x15: Fix RTC aliases
  ARM: dts: am57xx-beagle-x15: Fix IRQ type for mcp7941x
  ARM: dts: omap3: Add #iommu-cells to isp and iva iommu
  ARM: omap2plus_defconfig: Enable EXTCON_USB_GPIO
  ARM: dts: OMAP3-N900: Add microphone bias voltages
  ARM: OMAP2+: Fix omap off idle power consumption creeping up
  MAINTAINERS: Update brcmstb entry
  MAINTAINERS: Remove Christian Daudt for mach-bcm
  ...

Pull user-namespace fix from Eric Biederman:
 "Eric Windish recently reported a really bug that allows mounting fresh
  copies of proc and sysfs when it really should not be allowed.  The
  code attempted to verify that proc and sysfs were fully visible but
  there is a test missing to ensure that the root of the filesystem is
  visible.  Doh!

  The following patch fixes that.

  This fixes a containment issue that the docker folks are seeing"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
  mnt: Fix fs_fully_visible to verify the root directory is visible

Pull irq updates from Thomas Gleixner:
 "Two patches from the irq departement:

   - a simple fix to make dummy_irq_chip usable for wakeup scenarios

   - removal of the gic arch_extn hackery.  Now that all users are
     converted we really want to get rid of the interface so people wont
     come up with new use cases"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip: gic: Drop support for gic_arch_extn
  genirq: Set IRQCHIP_SKIP_SET_WAKE flag for dummy_irq_chip

Pull timer fix from Thomas Gleixner:
 "A simple fix to actually shut down a detached device instead of
  keeping it active"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  clockevents: Shutdown detached clockevent device

We cast away the volatile, but really, why make it volatile at all?
We already do a mb() inside the cpumask_empty() loop.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This fixes a dumb bug in fs_fully_visible that allows proc or sys to
be mounted if there is a bind mount of part of /proc/ or /sys/ visible.

Cc: stable@vger.kernel.org
Reported-by: NEric Windisch <ewindisch@docker.com>
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>